3Com 3012 Command Reference Manual

Description Using the if-match dscp command, you can define DSCP match rule. Using the undo if-match dscp command, you can delete DSCP match rule. You can configure this command for a class for several times. When a command is configured, the ip-dscp-value will be sorted in the ascending order automatically. Only when the specified DSCP values are identical with those in the rule (sequence may be different), can the command be deleted. Up to 8 DSCP values can be configured by a command. If several DSCPs are configured with the same v ...

Commands 6.1 isdn ignore callednum Syntax isdn ignore callednum undo isdn ignore callednum View ISDN BRI interface view, CE1/PRI interface view, CT1/PRI interface view Parameter None Description Using the isdn ignore callednum command, the user can disable the SETUP ACK messages if the received SETUP messages in data service calls do not carry the called number information.. Using undo isdn ignore callednum command, the router will send SETUP ACK messages. By default, the router that is interoperating with an exchange sends SETUP ACK messages even if t ...

Description Using the qmtoken command, you can configure the number of QoS sending tokens. Using the undo qmtoken command, you can disable the sending token function of QoS. By default, disable QoS sending token function. In such operation as FTP transmission, QoS queue may become invalid since the upper layer provides flow control function. QoS sending token function provides a kind of traffic control mechanism for the lower layer queue, and the number of packets sent to the lower layer interf ...

Syntax public-key-code end View Public key view Parameter None Description Using the public-key-code end command, you can end the public key editing and save the configured public key. Besides, you can also use this command to return from the public key view to the system view. After ending the public key editing by executing this command, the system will verify the validity of the key before saving the key. If there is any invalid character in the character string, the system will prompt that it will discard all the public key data configured by the user due to the p ...

outbound: Outbound direction. policy-name: Policy name. Description Using the qos apply policy command, you can attach an associated QoS policy to an interface. Using the undo qos apply policy command, you can delete associated QoS policy from an interface. If the sum of the bandwidths specified for the assured and expedited forwarding classes in a QoS policy exceeds the available bandwidth on the interface, the policy cannot be applied on the interface. When the available bandwidth on the interface is modified, the policy will be delet ...

Syntax wred ip-precedence value low-limit low-limit high-limit high-limit [ discard-probability discard-prob ] undo wred ip-precedence value View Policy-class view Parameter value: Precedence of IP packets in the range of 0 to 7. low-limit: Lower threshold value in the range of 1 to 1024. It is 10 by default. high-limit: Upper threshold value in the range of 1 to 1024. It is 30 by default. discard-prob: Denominator of drop proportion in the range of 1 to 255. It is 10 by default. Description Using wred ip-precedence command, you can set precedence lower-limit, upper-li ...

undo car View Policy-class view Parameter cir rate: Committed information rate in the range of 8000 to 155000000 bit/s. cbs size: Committed burst size, that is, the number of bits that can be sent in each interval in the range of 15000 to 155000000 bits. By default, it is 15000. ebs size: Excessive burst size in the range of 0 to 155000000 bits. By default, it is 0. Conform: Action (defaulted to pass) conducted to the packets when the traffic of the packets conforms to the CIR. exceed: Action (defaulted to d ...

user, in which case the user will be unable to log into the system. By default, no login authentication mode is specified, that is, the user is unable to log into the system. You must specify an authentication mode for a new user, otherwise, the user will be unable to log into to the system. The authentication mode set for the new user will take effect the next time when the user log into the system. For related command, see display ssh user-information. Example Set the authentication mode to password for the us ...