Metra Electronics 95-7899 Installation Instructions Manual

Phillips Screwdriver • Utility Knife • Socket Wrench 1-800-221-0932 www.metraonline.com KIT FEATURES © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION APPLICATIONS 2001-2005 Honda Civic (Except 2005 Civic SE) • Double DIN Head Unit Provision • Stacked ISO DIN Head Unit Provision •A) Double DIN Trim Plate KIT COMPONENTS TOOLS REQUIRED: 95-7899 A

Center Console Without Armrest . . . . . . . . . . . . . . . . . . . . . . . . 1 Center Console With Armrest . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - Double DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 TABLE OF CONTENTS 95-7899

CENTER CONSOLE WITHOUT ARMREST CLIP CLIP A B C D 95-7899 Disconnect the negative battery terminal to prevent an accidental short circuit. 1 Unclip the parking brake trim panel and remove (2) Phillips screws exposed. (Figure A) 2 Remove (1) Phillips screw and (1) clip from each side of the center console. (Figure B) Slide the console rearward to access (2) Phillips screws on the power outlet panel. (Figure C) 3 With ashtray: Remove the ashtray and (1) screw from inside ashtray cavity. Without ashtray: Skip to step five. 4 Unclip the power outlet panel and remove (2) Phillips screws exposed. (Figure C) 5 Unclip the dash trim panel assembly (including the head unit and the cli- mate controls) and remove assembly. 6 Remove (3) screws securing the cli- mate control pod to the back of the assembly and remove pod. 7 Remove (4) Phillips screws securing the factory head unit to the bracket assembly and remove the unit. (Figure D) 8 DASH DISASSEMBLY

terminal to prevent an accidental short circuit. 1 Automatic transmission: a. Apply parking brake and place shifter in neutral position. b. Unclip and remove trimring around shifter. (Figure A) Manual transmission: a. Apply parking brake b. Remove the shifter knob by hold- ing the plastic section above the boot down firmly with one and turn- ing the knob counterclockwise with the other hand. 2 Unclip and remove center console trim panel (Figure B) and remove (2) screws exposed. (Figure C) 3 With ashtray: Remove the ashtray and (1) screw from inside ashtray cavity. Without ashtray: Skip to step five. 4 Gently pry out on the center console edge trim (Figure D) to release the four rear clips, then pull the trim toward the rear to release the remaining clips and remove (2) Phillips screws exposed. 5 Unclip the dash trim panel assembly (including the head unit and the cli- mate controls) and remove assem- bly. 6 Remove (3) screws securing the cli- mate control pod to the back of the assembly and remove pod. 7 Remove (4) Phillips screws securing the factory head unit to the bracket assem- bly and remove the unit. 8 DASH DISASSEMBLY 2001-2005 HONDA CIVIC (EXCEPT 2005 CIVIC SE) CENTER CONSOLE WITH ARMREST

Trimplate. (Figure A) 1 Skip to step #1 in the Final Assembly. 4 Snap the DDIN Trimplate into the bracket and unit assembly. (Figure B) 2 Attach the aftermarket radio to the factory brackets by aligning the holes and securing it to the brackets using the screws supplied with radio. (Figure C) 3 DOUBLE DIN HEAD UNIT PROVISION A B C

bracket & unit assembly. (Figure B) 2 Skip to step #1 in the Final Assembly. 4 Depending on the type of aftermar- ket head units being installed (ie: Flip down, removable and motorized faced head units) the center bar may have to be removed and a small por- tion of the inside top and bottom edge of the DDIN Trimplate may have to be filed slightly. (Figure A) 1 3 STACKED ISO HEAD UNIT PROVISION A B C Attach the stacked head units to the factory brackets by aligning the holes and securing them to the brackets using the screws supplied with the units. (Figure C)

B) Twist ends together C) Solder D) Tape B C D Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. FINAL WIRING CONNECTIONS 95-7899 FINAL ASSEMBLY 12V Ignition / Acc . . . Red 12V Batt / Memory . . Yellow Ground . . . . . . . . . . . Black* Power Antenna . . . . . Blue Amp Turn-On . . . . . . Blue / White Amp Ground . . . . . . . Black / White Illumination. . . . . . . . Orange Dimmer . . . . . . . . . . Orange / White Right Front (+) . . . . . Gray Right Front (-). . . . . . Gray/ Black Left Front (+) . . . . . . White Left Front (-). . . . . . . White / Black Right Rear (+). . . . . . Violet Right Rear (-) . . . . . . Violet / Black Left Rear (+). . . . . . . Green Left Rear (-) . . . . . . . Green / Black METRA / EIA WIRING CODE *NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.