ADS ADS-BM1 Install Manual

damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be in- stalled by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately) install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN hardware ADS-BM1 accessories ADS-USB (REQUIRED)    fiRmware OEM-IDS(RS)-BM1-[ADS-BM1] www.idatastart.com Automotive Data Solutions Inc. © 2014 15748

* If equipped with a factory hood switch. ** If equipped with an electric E-brake and it is activated, vehicle will shudown when a door is opened during RS sequence. *** If equipped with the Confort Access System, the door handles will not be functional during RS sequence. MAKE MODEL YEAR INSTALL TYPE FEATURES REMOTE START FROM OEM REMOTES SECURE TAKEOVER** DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE PARKING LIGHT CTRL RAP SHUTDOWN CTRL TACHOMETER STATUS MONITORING BRAKE PEDAL STATUS MONITORING VSS STATUS MONITORING GLOW PLUG STATUS MONITORING DOOR STATUS MONITORING TRUNK STATUS MONITORING HOOD STATUS MONITORING* BMW 1 Series PTS AT 08-13 1 • • • • • • • • • • • • • • • • • 3 Series PTS AT*** 06-11 1 • • • • • • • • • • • • • • • • • 3 Series Coupe PTS AT*** 07-13 1 • • • • • • • • • • • • • • • • • 5 Series PTS AT 05-10 1 • • • • • • • • • • • • • • • • • 6 Series PTS AT 05-10 1 • • • • • • • • • • • • • • • • • 1M PTS AT 11 1 • • • • • • • • • • • • • • • • • M3 PTS AT*** 08-12 1 • • • • • • • • • • • • • • • • • M3 Coupe PTS AT*** 08-13 1 • • • • • • • • • • • • • • • • • M5 PTS AT 06-10 1 • • • • • • • • • • • • • • • • • M6 PTS AT 06-10 1 • • • • • • • • • • • • • • • • • X1 PTS AT*** 12-14 1 • • • • • • • • • • • • • • • • • X5 PTS AT 07-13 1 • • • • • • • • • • • • • • • • • X5 Diesel PTS AT 07-13 1 • • • • • • • • • • • • • • • • • • X5 M PTS AT 10-13 1 • • • • • • • • • • • • • • • • • X6 PTS AT 08-14 1 • • • • • • • • • • • • • • • • • X6 M PTS AT 10-14 1 • • • • • • • • • • • • • • • • • Z4 PTS AT*** 09-14 1 • • • • • • • • • • • • • • • • • MINI Clubman PTS AT*** 08-14 1 • • • • • • • • • • • • • • • • • Cooper PTS AT*** 07-14 1 • • • • • • • • • • • • • • • • • Cooper Convertible PTS AT*** 08-14 1 • • • • • • • • • • • • • • • • • Countryman / ALL-4 PTS AT 11-14 2 • • • • • • • • • • • • • • • • • Coupe PTS AT*** 12-14 1 • • • • • • • • • • • • • • • • • Paceman PTS AT 13-14 2 • • • • • • • • • • • • • • • • • Roadster PTS AT*** 12-14 1 • • • • • • • • • • • • • • • • • NOTES I This fi rmware covers Automatic Transmission (AT) vehicles only. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 2 of 18 • 20140807 DOC.: #15748

OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 3 of 18 • 20140807 BOX CONTENTS - 1 OF 1 2 1 3 4 2 1 3 4 2 1 3 2 1 3 7 9 3 10 8 11 13 14 12 15 17 18 19 20 16 6 4 1 2 5 3 6 4 1 2 5 3 6 4 1 2 5 7 9 3 10 8 1113 14 12 1517 18 16 6 4 1 2 5 ADS-HRNBMW01-2 7 9 3 10 8 6 4 1 2 5 2 1 2 1 3 4 2 1 3 4 2 1 3 4 7 9 3 10 8 11 12 6 4 1 2 5 MODULE BOX CONTENTS 18 PIN WHITE CONNECTOR - ADAPTER CABLE AFTERMARKET HOOD SWITCH AND CABLE STICKER 1 EXPANSION PACK STICKER 2 10 PIN WHITE CONNECTOR 12 PIN BLACK CONNECTOR PROGRAMMING BUTTON LED 1 LED 2 XP LED 1 LED LED XP LED 2 RED BLUE BLACK BLACK RF PORT/WEBLINK PORT BLACK BLUE BLACK BLACK BLACK TOP VIEW TOP VIEW BOTTOM VIEW BLACK USB BLUE TELEMATIC PORT WHITE BLACK EXPANSION PACK ASSEMBLY EXPANSION CABLE WHITE T-HARNESS 1 T-HARNESS 2 T-HARNESS 2 THE ADS-HRNBMW01-2 CABLE IS INCLUDED IN KITS MANUFACTURED AFTER 11/12/2013. CONTACT YOUR AUTHORIZED DEALER, IF THIS CABLE IS NOT INCLUDED. WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE COMPUTER USB PORT 4 PIN BLACK CABLE MODULE WEBLINK PORT DOC.: #15748

imPoRtant instaLL viDeo gaLLeRY avaiLabLe onLine Before installing this product, consult our Install Video Gallery and watch: • Vehicle Disassembly Procedure videos • Module Connection Procedures videos • Module Programming Procedures videos Simply visit our forum and register at http://www.12voltdata.com/forum/viewtopic.php?f=340&t=9683&sid=a61772b486e4584ad6f058b171ffa425 www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 4 of 18 • 20140807 DOC.: #15748

START vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. Turn ignition to OFF position. Remove keyfob from keyport. Verify all keyfob functionalities (Door Lock, Door Unlock, Trunk Release and Comfort Access System if equipped). Insert the expansion pack into module. Connect the module to the computer with the WEBLINK cable. Flash the module with the latest fi rmware then fl ash the expansion pack. Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING DIAGRAM. WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages. START vehicle. Verify all vehicle functionalities. WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support. Turn ignition to OFF position. Remove keyfob from keyport. Connect and secure every connector to the module, as shown in STEP 2 of the WIRING DIAGRAM. Connect and secure every connector of the expansion cable to the module, as shown in STEP 3 of the WIRING DIAGRAM. If required, connect an accessory as shown in the COMPATIBLE ACCESSORIES section of the guide. If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING DIAGRAM. Put sticker 1 on a clean and visible surface in the engine bay and put sticker 2 under the dashboard near the OBDII connector. Module installation procedure completed. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 5 of 18 • 20140807 DOC.: #15748

STEP 3 CONNECT TO MODULE STEP 4 TYPE 1 - WIRING DIAGRAM - 1 OF 1 BRAKE HARNESS RELAY RELAY C2 HARNESS B2 HARNESS C1 CONNECTOR B1 CONNECTOR BRAKE SWITCH CONNECT THE FOLLOWING TO THE VEHICLE START THE VEHICLE WITH THE OEM KEYFOB TO TEST THE CONNECTIONS WHITE 18 PIN WARNING: THE ADAPTER CABLE IS NOT REQUIRED BLACK 4 PIN BLACK 6 PIN WARNING: THESE CONNECTORS HAVE TWO [2X] LOCKING MECHANISMS. INSERT THE CONNECTOR IN ITS HOUSING AND APPLY GENTLE PRESSURE ON BOTH EXTREMITIES TO SECURE THE CONNECTION. (TWO AUDIBLE CLICKS WILL BE HEARD.) MODULE BLACK 20 PIN STEP 1 STEP 2 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 WARNING 07 GRAY/WHITE - HOOD STATUS (-) INPUT 08 GRAY/BLACK (NOT USED) WHITE 10 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH CONNECT IF REQUIRED HOOD SWITCH MINI: BEHIND INSTRUMENT PANEL, DRIVER SIDE BMW: UNDER DASH, DRIVER SIDE COMFORT ACCESS SYSTEM MODULE www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 6 of 18 • 20140807 DOC.: #15748

MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR MINI Countryman / ALL-4 PTS AT 11-14 12V X14261 ~ 51 pin 02 Red/Yellow (+) Driver kick panel ~ Ground X14261 ~ 51 pin 47 Brown or Brown/Black (-) Driver kick panel ~ CanH X14261 ~ 51 pin 46 Orange/Green (DATA) Driver kick panel ~ CanL X14261 ~ 51 pin 45 Green (DATA) Driver kick panel ~ Paceman PTS AT 13-14 12V X14261 ~ 51 pin 02 Red/Yellow (+) Driver kick panel ~ Ground X14261 ~ 51 pin 47 Brown or Brown/Black (-) Driver kick panel ~ CanH X14261 ~ 51 pin 46 Orange/Green (DATA) Driver kick panel ~ CanL X14261 ~ 51 pin 45 Green (DATA) Driver kick panel ~ www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 7 of 18 • 20140807 DOC.: #15748

STEP 2 CONNECT TO MODULE STEP 3 TYPE 2 - WIRING DIAGRAM - 1 OF 1 BRAKE HARNESS RELAY RELAY KEYPORT HARNESS BRAKE SWITCH DRIVER KICK PANEL CONNECT IF WIRE IS PRESENT CONNECT THE FOLLOWING TO THE VEHICLE START THE VEHICLE WITH THE OEM KEYFOB TO TEST THE CONNECTIONS CUT AND REMOVE CONNECTORS FROM T-HARNESS WHITE 18 PIN WHITE 18 PIN ADAPTER CABLE BLACK 4 PIN BLACK 6 PIN WARNING: THESE CONNECTORS HAVE TWO [2X] LOCKING MECHANISMS. INSERT THE CONNECTOR IN ITS HOUSING AND APPLY GENTLE PRESSURE ON BOTH EXTREMITIES TO SECURE THE CONNECTION. (TWO AUDIBLE CLICKS WILL BE HEARD.) PINK (NOT USED) RED BLACK PINK/YELLOW PINK/RED BLACK GROUND - 47 GROUND - 47 CANH - 46 CANL - 45 12V (+) - 02 MODULE BLACK 20 PIN STEP 1 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 WARNING 07 GRAY/WHITE - HOOD STATUS (-) INPUT 08 GRAY/BLACK (NOT USED) WHITE 10 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH CONNECT IF REQUIRED HOOD SWITCH STEP 4 KEYPORT CONNECTOR www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 8 of 18 • 20140807 DOC.: #15748

LED 1 is solid RED. Insert keyfob 1 into keyport. Within 10 seconds, LED 1 will fl ash GREEN once (1x). Remove keyfob 1 from keyport. LED 1 will turn solid RED. Wait 5 seconds. Insert keyfob 1 into keyport. Within 10 seconds, LED 1 will fl ash GREEN rapidly. Remove keyfob 1 from keyport. WARNING: Follow steps 4, 3, 2 as shown in the wiring diagram to disconnect the module from the vehicle. Connect module to computer and proceed with KLON programming. WARNING: Follow steps 2, 3, 4 as shown in the wiring diagram to connect the module to the vehicle. LED 1 will turn solid RED. Insert keyfob 1 into keyport. LED 1 will turn solid GREEN for 2 seconds. Remove keyfob 1 from keyport. Module Programming Procedure completed. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 9 of 18 • 20140807 DOC.: #15748

NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Insert keyfob into keyport. Time restriction. Complete next step within 5 seconds. Cycle ignition ON fi ve times [5x OFF/ON] rapidly. Parking Light will fl ash once [1x]. Wait, Parking Light will fl ash once [1x] to indicate that the valet mode is ON or twice [2x] to indicate that the valet mode is OFF. Turn ignition to STOP position. Remove keyfob from keyport. Valet Mode Programming Procedure completed. To exit valet mode: repeat steps 1 to 6. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 10 of 18 • 20140807 DOC.: #15748

It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. Module must be programmed to the vehicle. Use the Module Navigation Chart on the next page. Set ignition to OFF position. TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will fl ash GREEN an equal amount of times continuously. TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will fl ash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will fl ash GREEN an equal amount of times continuously. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. LED 1 will fl ash RED as many times as the current option number continuously. Configure every other setting and proceed to step 13. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will fl ash RED rapidly. Release programming button. LED 1 will turn OFF. Module navigation completed. Failure to exit the Module Navigation will drain vehicle battery. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 11 of 18 • 20140807 DOC.: #15748

moDuLe navigation chaRt: notes [X] menus [Y] oPtions [Z] settings I Default settings are listed in bold. 01 CONFIGURATION 01 DISARM/UNLOCK BEFORE START 01 oFF II Make sure the option is covered on the vehicle before attempting to change the setting. 02 ON 02 RELOCK AFTER START 01 oFF 02 ON 03 RELOCK AFTER SHUTDOWN 01 oFF 02 ON 04 FORCE UNLOCK ALL ON FIRST PRESS 01 oFF 02 ON 05 TAKEOVER 01 enabLe 02 DISABLE* 06 SECURE TAKEOVER DELAY 01 45 sec 02 90 SEC 03 03 MIN 04 04 MIN 07 FACTORY KEYLESS RS SEQUENCE 01 DISABLE 02 N/A 03 LOCK + UNLOCK + LOCK 04 LocK + LocK + LocK 08 MODULE RUN TIME 01 03 MIN 02 05 MIN 03 10 MIN 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 15 min 09 WAIT TO START DELAY 01 02 sec 02 05 SEC 03 08 SEC 04 10 SEC 05 15 SEC 06 20 SEC 07 25 SEC 08 30 SEC 10-15 N/A 01 N/A 02-07 Technical Support only 01 N/A 01 N/A *Vehicle will shutdown when a door is opened. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 12 of 18 • 20140807 DOC.: #15748

Remote staRteR eRRoR coDes: notes [X] numbeR oF PaRKing Light FLashes Diagnostic I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II After a remote starter failure, the parking lights will fl ash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 N/A 11 N/A 12 N/A 13 N/A 14 N/A 15 N/A 16 CAN communication failure during RS sequence. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 13 of 18 • 20140807 DOC.: #15748

test moDuLe LeD 1 status Diagnostic I DURING PROGRAMMING Flashing RED Missing/wrong information from fi rmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. II DURING REMOTE START Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. III WITH IGNITION OFF Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 14 of 18 • 20140807 DOC.: #15748

Disconnect all connectors from module except the BLACK 20-PIN connector. Disconnect the BLACK 20-PIN connector. PRESS AND HOLD programming button while connecting the BLACK 20-PIN connector. Wait, LED 1 will flash RED. RELEASE programming button. LED 1 will turn RED for 2 seconds. Module RESET completed. Reconnect all connectors. Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 15 of 18 • 20140807 DOC.: #15748

All vehicle doors must be closed and locked prior to remote start sequence. Time restriction. Complete steps 2 to 5 within 45 seconds. Unlock driver door. Open driver door and enter vehicle. Close driver door. Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 16 of 18 • 20140807 DOC.: #15748

checKList 01 WARNING: Vehicle engine will start many times. Test in a well ventillated area. 02 Open driver door window for easy vehicle access. 03 Close all vehicle doors, hood and trunk. 04 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? ¨ ¨ YES: Go to step 5. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connection, repeat step 4 and call technical support if the problem persist. 05 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? ¨ ¨ YES: Go to step 6. NO: Repeat step 5. If problem persists, push vehicle start button once [1x] to shut down the vehicle and call technical support. 06 Unlock and open driver door. 07 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 3: Does the vehicle remote start? ¨ ¨ YES: The module does NOT detect the door signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support. NO: Go to step 8. 08 Open hood. Question 4: Is the orange warning sticker "Sticker 1" placed under the hood? ¨ ¨ YES: Leave hood open and go to step 9. NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 9. 09 Close all doors. 10 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 5: Does the vehicle remote start? ¨ ¨ YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to Question 6. NO: Go to step 11. Question 6: Is the vehicle equipped with a factory hood switch? (Inside hood latch) ¨ ¨ YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support. NO: Install the mandatory hood switch included in the kit. Repeat installation checklist. 11 Close hood. 12 Enter vehicle. Do NOT press brake pedal. 13 Close all doors. 14 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 15 Wait for the vehicle to start. 16 Press brake pedal. Question 7: Does the vehicle shut down? ¨ ¨ YES: Go to step 17. NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support. 17 Apply parking brake. 18 Exit vehicle. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 17 of 18 • 20140807 DOC.: #15748

checKList 19 Close all doors. 20 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 21 Wait for the vehicle to start. Question 8: Is the vehicle equipped with Comfort Access System ? ¨ ¨ YES: For 1, 5, 6, X5, X6: Touch exterior driver door handle to unlock door using Comfort Access System. Within 45 seconds, go to step 22. YES: For 3, X1, Z4, Mini: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22. NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22. 22 Open driver door. Question 9: Does the vehicle shut down? ¨ ¨ YES: For Z4, X5, X6: Go to step 25. YES: For 1, 3, 5, 6, X1: The module does NOT detect the parking brake signal or the unlock signal from the vehicle communication network. Call technical support. NO: For Z4, X5, X6: The module does NOT detect the parking brake signal correctly from the vehicle communication network. Call technical support. NO: For 1, 3, 5, 6, X1: Go to step 23. 23 Press and release brake pedal. 24 Push vehicle start button once [1x] to shut down the vehicle. 25 Installation checklist completed. www.idatastart.com Automotive Data Solutions Inc. © 2014 OEM-IDS(RS)-BM1-[ADS-BM1]-EN Page 18 of 18 • 20140807 DOC.: #15748