Mitsubishi Eclipse Owner's Manual

SPYDER. We are confident you will enjoy your vehicle. It has been engi- neered for optimum performance, durability and comfort. By thoroughly reading this Owner’s Manual, you will gain an understanding of the many features that are included in the ECLIPSE/ECLIPSE SPYDER. The Owner’s Manual contains descriptions and illustrations that will assist in the operation and maintenance of your vehicle. Your Authorized Mitsubishi Motors Dealer will be happy to assist you with any further questions you may have regarding the operation of your vehicle. Please note that this manual applies to all ECLIPSE/ECLIPSE SPYDER models and explains all features including options. Some features explained in this manual may not be installed on your vehicle. Please leave this Owner’s Manual in the vehicle at the time of resale. The next owner will appreciate having access to the information contained here. This manual includes instructions for standard and optional equipment available at the time of printing. Mitsubishi Motors Corporation reserves the right to make changes in design and specifications and to make additions or improvements in its product without assuming any obligation to install these on previously manufactured products. Throughout this manual the words WARNING and CAUTION appear. These are reminders to be especially careful. Failure to follow the instructions could result in personal injury or damage to your vehicle. WARNING ! Indicates a strong possibility of severe personal injury or death if instructions are not followed. CAUTION ! Points out hazards or unsafe practices that could cause minor personal injury or damage to your vehicle. You will see another important symbol: NOTE Gives helpful information. WARNING ! G Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects and reproduc- tive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. ©2009 Mitsubishi Motors Corporation Printed in U.S.A. This vehicle is manufactured by Mitsubishi Motors North America, Inc. in U.S.A. under license from Mitsubishi Motors Corporation. 09PS24_28(NAFTA)_Cover2.fm 1 ページ ２００８年８月８日　金曜日　午前８時３２分

1 2 3 4 5 6 7 8 9 Overview Quick index General information Seat and restraint systems Features and controls Driving safety Comfort controls For emergencies Vehicle care and maintenance Customer assistance/Reporting Safety Defects Specifications BK0098300US.book 1 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00100201114 Combination headlights and dimmer switch P.3-127 Turn signal lever P.3-131 Supplemental restraint system - air bag (for driver’s seat) P.2-36 Horn switch P.3-138 Electric remote-controlled outside mirror switch P.3-59 Front fog light switch (if so equipped) P.3-133 Steering wheel audio remote control switch (if so equipped) P.5-65 Instrument cluster P.3-106 Cruise control lever P.3-91 Ignition switch P.3-61 Wiper and washer switch P.3-134 Fuses P.7-38 ASC off switch (if so equipped) P.3-87 Engine hood release lever P.7-4 Steering wheel tilt lock lever P.3-55 Front fog light switch (if so equipped) P.3-133 Headlights leveling switch (if so equipped) P.3-130 ASC off switch (if so equipped) P.3-87 BK0098300US.book 1 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00100201127 Supplemental restraint system - air bag (for front passenger’s seat) P.2-36 Glove compartment P.3-177 Audio system P.5-24, 5-26, 5-39 Hazard warning flasher switch P.3-132 Vents P.5-2 Multi center display P.3-116 Passenger’s air bag off indicator P.2-43 Front passenger seat belt warning light P.2-19 Hands-free Bluetooth® cellular phone interface system with voice rec- ognition (if so equipped) P.3-139 BK0098300US.book 2 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00100201130 Gearshift or selector lever P.3-67, 3-72 Parking brake lever P.3-54 Floor console box P.3-178 Cup holder P.3-179 Heated seat switch (if so equipped) P.2-10 Air conditioning P.5-5, 5-14 Electric rear window defogger switch P.3-137 Electric convertible top (ECLIPSE SPYDER) Operation indicator lamp Top (OPEN) switch P.3-33 Top (CLOSE) switch P.3-33 Power outlet P.3-170 Auxiliary Audio connector (mini-jack) P.5-63 BK0098300US.book 3 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Dome light (Front)/Reading lights P.3-171, 3-172, 7-50, 7-68 Inside rearview mirror P.3-56, 3-104 Sun visors P.3-168 Vanity mirror (if so equipped) P.3-169 Supplemental restraint system - side air bag (for front seats) P.2-51 Adjustable seat belt shoulder anchor (for front seats) P.2-19 Seat belts P.2-13 Front seats P.2-4 Head restraints P.2-12 Sunroof switch P.3-28 Except for vehicles with sunroof Vehicles with sunroof Inside rearview mirror P.3-56, 3-104 Reading lights (if so equipped) P.3-174, 7-50, 7-69 Window lock switch P.3-28 Power door lock switch P.3-15 ECLIPSE Dome light (Front)/Reading lights (if so equipped) P.3-171, 3-173, 7-50 BK0098300US.book 4 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Supplemental restraint system - curtain air bag P.2-52 Rear shelf panel (if so equipped) P.3-180 Coat hooks (if so equipped) P.3-181 Dome light (Rear) P.3-171, 7-50, 7-68 ECLIPSE BK0098300US.book 5 ページ ２００８年１２月８日　月曜日　午前１１時３７分

system P.2-28 Jack P.6-9 Tools P.6-8 Spare tire P.6-11 Luggage hooks P.3-182 Luggage hooks P.3-182 Tether anchors for child restraint system P.2-28 Inside rear hatch/trunk lid release P.3-18 Cargo area light P.3-176, 7-50, 7-69 ECLIPSE BK0098300US.book 6 ページ ２００８年１２月８日　月曜日　午前１１時３７分

P.3-28 ECLIPSE Outside rearview mirrors P.3-59 Fuel tank filler door P.1-4 Locking and unlocking P.3-13 Keyless entry system P.3-7 Front fog lights (if so equipped) P.3-133, 7-48, 7-57 Engine compartment P.7-6 Engine hood P.7-4 Windshield wiper and washer P.3-134 Headlight P.3-127, 7-48, 7-51 Front turn-signal, parking and side-marker lights P.3-131, 7-48, 7-56 Headlight P.3-127, 7-48, 7-52 Vehicles with high intensity discharge (HID) type headlights Except for vehicles with high intensity discharge (HID) type headlights Parking and side-marker light P.3-127, 7-48, 7-53 Front turn signal light P.3-131, 7-48, 7-55 BK0098300US.book 7 ページ ２００８年１２月８日　月曜日　午前１１時３７分

License plate light P.7-49, 7-66 Back-up lights P.7-49, 7-59 Tire inflation pressure P.7-23 Changing tires P.6-9 Tire rotation P.7-26 Tire chains P.7-29 Tire pressure monitoring system P.3-97 Rear turn signal lights P.3-131, 7-49, 7-59 Rear side-marker lights P.3-127, 7-49, 7-59 Stop and tail lights P.3-127 Rear window wiper and washer (if so equipped) P.3-136 Rear hatch button P.3-16 ECLIPSE Satellite radio antenna (if so equipped) P.5-75 High-mounted stop light (vehicles with large rear spoiler) P.7-49 High-mounted stop light (except for vehicles with large rear spoiler) P.7-49 Rear-view camera (if so equipped) P.3-104 BK0098300US.book 8 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Sun visors P.3-168 Vanity mirror (if so equipped) P.3-169 Supplemental restraint system - side air bag (for front seats) P.2-51 Seat belts P.2-13 Front seats P.2-4 Head restraints P.2-12 Inside rearview mirror P.3-56, 3-104 Window lock switch P.3-28 Power door lock switch P.3-15 ECLIPSE SPYDER Rear seat P.2-11 Dome light (Front)/Reading lights P.3-171, 3-173, 7-50 BK0098300US.book 9 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Inside emergency trunk lid release P.3-20 ECLIPSE SPYDER BK0098300US.book 10 ページ ２００８年１２月８日　月曜日　午前１１時３７分

P.3-59 Fuel tank filler door P.1-4 Locking and unlocking P.3-13 Keyless entry system P.3-7 Front fog lights P.3-133, 7-48, 7-57 Engine compartment P.7-6 Engine hood P.7-4 Windshield wiper and washer P.3-134 Headlight P.3-127, 7-48, 7-51 Front turn-signal, parking and side-marker lights P.3-131, 7-48, 7-56 Headlight P.3-127, 7-48, 7-52 Vehicles with high intensity discharge (HID) type headlights Except for vehicles with high intensity discharge (HID) type headlights Parking and side-marker light P.3-127, 7-48, 7-53 Front turn signal light P.3-131, 7-48, 7-55 BK0098300US.book 11 ページ ２００８年１２月８日　月曜日　午前１１時３７分

License plate light P.7-49, 7-66 Back-up lights P.7-49, 7-59 Tire inflation pressure P.7-23 Changing tires P.6-9 Tire rotation P.7-26 Tire chains P.7-29 Tire pressure monitoring sys- tem P.3-97 Rear turn signal lights P.3-131, 7-49, 7-59 Rear side-marker lights P.3-127, 7-49, 7-59 Stop and tail lights P.3-127 Trunk lid button P.3-16 ECLIPSE SPYDER Satellite radio antenna (if so equipped) P.5-75 High-mounted stop light P.7-49 Rear-view camera P.3-104 BK0098300US.book 12 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00200700979 NOTE G These warning lights will come on for a few seconds for a bulb check when the ignition key is first turned to “ON”. Warning light Do this Ref. page Charging system warning light G Park your vehicle in a safe place and stop the engine. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance. P.3-115 Oil pressure warning light G Park your vehicle in a safe place and stop the engine, then check the engine oil level. If the light comes on while the engine oil level is normal, have the system checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. P.3-115 or Brake warning light G If this light comes on while driving, check to see that the parking brake is fully released. G If this light stays on after releasing the parking brake, stop and check the brake fluid level. G If the brake fluid level is correct, there may be a system malfunction. Avoid hard braking and high speeds, and contact an authorized Mit- subishi Motors dealer or a repair facility of your choice for assistance. P.3-113 BK0098300US.book 1 ページ ２００８年１２月８日　月曜日　午前１１時３７分

ment cluster flashes rapidly (twice per second) (if so equipped) G Park your vehicle in a safe place. Idle the engine until the selector lever position indicator stops flash- ing. If the indicator does not go off, have the system checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. P.3-75 or Engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”) G Although your vehicle will usually be drivable and not need towing, have the engine system checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. If the vehicle is not drivable, contact emergency roadside assistance at 1- 888-648-7820 (for vehicles sold in U.S.A.) or 1-888-576-4878 (for vehicles sold in Canada), an authorized Mitsubishi Motors dealer, or local towing company for assistance. P.3-114 Anti-lock braking system warning light G Park your vehicle in a safe place and stop the engine. Test the system as described on page 3-83. G If the light does not go out after the test, or if it comes on again, we recommend that you have the system checked at an authorized Mit- subishi Motors dealer or a repair facility of your choice as soon as possible. G When this light comes on, the anti-lock braking system is not func- tioning and only the ordinary braking system is functioning. P.3-83 SRS warning light G It is not necessary to stop the vehicle immediately, but we recommend that you have the air bag and the pre-tensioner seat belt system checked at an authorized Mitsubishi Motors dealer as soon as possi- ble. P.2-24, 2-44 Warning light Do this Ref. page BK0098300US.book 2 ページ ２００８年１２月８日　月曜日　午前１１時３７分

ment cluster flashes slowly (once per second) (if so equipped) G Have the automatic transaxle checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. P.3-75 and ASC indicator and ASC OFF indicator G Park your vehicle in a safe place and turn off the engine. Restart the engine and check to see if the indicator comes on again. G If the indicator does not go out, or if it comes on again, have your vehicle inspected at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. G When this indicator comes on, the active stability control is not func- tioning and normal operation of the vehicle will not be affected. P.3-88 Tire pressure monitoring system warning light G If the warning light comes on, you should stop and adjust the tires to the proper inflation pressure as soon as possible. (See “Tire inflation pressures” on page 7-23.) Once adjustments have been made, the warning light will go off after a few minutes of driving. G If the warning light blinks for approximately 1 minute and then remains continuously illuminated, the system is not operating prop- erly. If the system returns to normal, the warning light will go off. If the warning light does not go off, have the vehicle inspected at an authorized Mitsubishi Motors dealer. P.3-99 Warning light Do this Ref. page BK0098300US.book 3 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00200800664 Sound Do this Ref. page Constant tone when the driver’s door is opened. “Key reminder buzzer” A tone will sound if the driver’s door is opened while the ignition key is in the “LOCK” or “ACC” position. Remove the key to stop the tone. OR P.3-14 “Headlight reminder buzzer” A tone will sound if the driver’s door is opened when the ignition key is in the “LOCK” or “ACC” position or removed from the ignition switch while the lights are on. Turn the lights off. The tone will stop automatically when the lights are automatically turned off. (See page 3-128 for auto-cutout function.) P.3-129 BK0098300US.book 4 ページ ２００８年１２月８日　月曜日　午前１１時３７分

brake pedal while driving. “Brake pad wear alarm” The brake pads are worn down to the serviceable limit. Have the brake pads replaced at an authorized Mitsubishi Motors dealer or a repair facility of your choice. P.3-82 Tone when the ignition key is turned to the “ON” position. “Seat belt reminder buzzer” When the ignition key is turned to the “ON” position, the tone will sound for about 6 seconds. If the driver’s seat belt remains unfastened 1 minute later, the tone will sound intermittently (12 times) when the vehicle is driven. If the driver’s seat belt subsequently remains unfastened while the vehicle is being driven, the tone will sound as a warning each time the vehicle stops and starts. When the driver’s seat belt is fastened, the tone will stop. P.2-18 Tone when the vehicle is moving at more than 5 mph (8 km/h). “Door-ajar warning buzzer” Door or rear hatch (ECLIPSE) is not properly shut. If you shut the door or rear hatch (ECLIPSE), the tone will stop. P.3-116 When the headlights have flashed for three minutes, the horn will sound inter- mittently for three minutes. “Theft-alarm system” The theft-alarm system is operating. To stop the alarm, use the keyless-entry transmitter to lock or unlock the doors or rear hatch (ECLIPSE) or the trunk lid (ECLIPSE SPYDER). Alternatively, turn the ignition key to the “ON” position. P.3-22 Sound Do this Ref. page BK0098300US.book 5 ページ ２００８年１２月８日　月曜日　午前１１時３７分

(ECLIPSE SPYDER) N00200100029 Indicator Lamp Tone Do this Ref. page Flashes slowly (approx. one flash per second). Sounds intermit- tently and rapidly (approx. three times per second). G The requirements for operation of the electric convertible top are not all satisfied. Ensure satisfaction of all the require- ments. P.3-32 G The indicator and tone indicate that the electric convertible top is not going to operate. • Check whether the OPEN switch and CLOSE switch are both being pressed at the same time. • Check whether the OPEN (or CLOSE) switch is being pressed when the top is fully open (or closed). P.3-33, 3-36 G The indicator and tone indicate that the electric convertible top has temporarily stopped working because continuous operation of one switch then the other has triggered a protec- tion circuit. Wait about seven minutes, then try operating the electric convertible top again. P.3-33 Flashes rapidly (approx. two flashes per sec- ond). Sounds for approx. five sec- onds. G The top is partly open. Stop the vehicle and completely open or close the top. The tone will then stop. P.3-38 Sounds intermit- tently and slowly (approx. once per second). G The indicator and tone indicate a system fault. Have the vehi- cle inspected by an authorized Mitsubishi Motors dealer. P.3-38 BK0098300US.book 6 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00200900678 Problem Do this Ref. Page Cannot turn the key. From “LOCK” to “ACC” Turn the key while jogging the steering wheel in either direction. From “ACC” to “LOCK” Vehicles with automatic transaxle: Check the position of the selector lever. The key cannot be removed unless the selector lever is set to the “P” (PARK) position. Vehicles with manual transaxle: Place the key at the “ACC” position. Push the key in and turn it. P.3-62, 3-63 Cannot shift the selector lever from the “P” (PARK) position. (for vehicles with automatic transaxle) Shift the selector lever while pressing the brake pedal. Check that the ignition key is in the “ON” position. P.3-72 The windows are fogged up. 1. Set the mode selection dial to the “ ” or “ ” position. 2. Turn on the blower. P.5-12, 5-20 The engine does not start. The lights do not come on. The lights are dim. The horn does not honk. The horn sound is weak. Have the battery checked. Recharge or replace as needed. P.6-2, 7-16 BK0098300US.book 7 ページ ２００８年１２月８日　月曜日　午前１１時３７分

ture gauge indicator is at the “H” (hot) position. Steam comes out of the engine compartment. The engine is overheated. Carefully stop the vehicle in a safe place. P.6-6 The vehicle is stuck in sand, mud, or snow. Move the gearshift lever or selector lever rhythmically between 1st and Reverse gears (for vehicles with manual transaxle) or “Sports mode” and “R” (REVERSE) positions (for vehicles with automatic transaxle), while pressing lightly on the accelerator pedal. P.6-22 WARNING ! G When attempting to rock your vehicle out of a stuck position, be sure that no one is near the vehicle. The rocking motion may cause the vehicle to suddenly lurch forward or backward, possibly injuring bystanders. G Avoid revving the engine or spinning the wheels. Prolonged efforts to free a stuck vehicle may result in overheating and transaxle failure. If the vehicle remains stuck after several rocking attempts, have a towing service pull the vehicle out. BK0098300US.book 8 ページ ２００８年１２月８日　月曜日　午前１１時３７分

properly after driving through water. Dry out the brakes by driving slowly while lightly pressing the brake pedal. P.4-6 The automatic transaxle does not shift when accelerating and/or the vehicle does not easily begin to move. There may be a problem in the automatic transaxle. Have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice. Shift the lever into 2nd gear of the sports mode when starting the vehicle. If the vehicle is on a level road, shift the lever back to “D” (DRIVE) position. (This method may or may not work depending on the type of malfunction.) P.3-80 A tire is punctured. 1. Park the vehicle in a safe place where the surface is flat and level. 2. Replace the flat tire with the spare tire. P.6-9 BK0098300US.book 9 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Filling the fuel tank . . . . . . . . . . . . . . . . . . . . . . . .1- 4 Modification of your vehicle . . . . . . . . . . . . . . . . .1- 7 Mitsubishi Motors genuine parts . . . . . . . . . . . . . .1- 9 California Perchlorate Materials Requirements. . .1- 9 BK0098300US.book 1 ページ ２００８年１２月８日　月曜日　午前１１時３７分

equipped with a fuel filler tube especially designed to accept only a small diameter unleaded gasoline dispensing nozzle. Gasoline detergent additives In the United States, fuel suppliers are required by law to add detergents to their gasoline to minimize fuel-injector fouling and minimize intake-valve deposits. Detergent gasoline helps keep your engine in tune and your emission-control system working properly. Octane requirement 2.4 liter engine model Your vehicle is designed to operate on unleaded gasoline hav- ing a minimum octane number of 87 [(MON+RON)/2], or 91 RON. 3.8 liter engine model Your vehicle is designed to operate on premium grade unleaded gasoline having a minimum octane number of 91 [(MON+RON)/2], or 95 RON. If premium grade unleaded gas- oline is not available, unleaded gasoline having an octane num- ber of 87 [(MON+RON)/2], or 91 RON may be temporarily use as an emergency measure, but only under the following precautions. G Have the fuel tank filled only partially with unleaded reg- ular gasoline, and fill up with unleaded premium gasoline as soon as possible. G Avoid full throttle driving and abrupt acceleration. MON: Motor Octane Number RON: Research Octane Number Oxygenated gasoline Gasoline sold at some service stations contains oxygenates such as ethanol and MTBE, although the oxygenates may not be identified by those names. Oxygenates are required in some areas of the country. Such fuel can be used in your vehicle. WARNING ! G Gasoline is highly flammable and explosive. You could be burned, seriously injured or killed when handling it. Whenever you refuel your vehicle, stop the engine and keep flames, sparks, and smoking materials away from the vehicle. Always handle fuel in well-ventilated outdoor areas. CAUTION ! G Using leaded gasoline in your vehicle will damage the engine, catalytic converter, and the oxygen sen- sors. Also, using leaded gasoline is illegal, and will void your warranty coverage of the engine, catalytic converter, and oxygen sensors. BK0098300US.book 2 ページ ２００８年１２月８日　月曜日　午前１１時３７分

gasoline may be used in your vehicle, provided the octane number is at least as high as that recommended for unleaded gasoline. Methanol Do not operate your vehicle on gasoline containing methanol (wood alcohol). Using this type of alcohol could adversely affect the vehicle’s performance and damage critical parts of the vehicle's fuel system. Reformulated gasoline Many areas of the country require the use of cleaner burning fuel referred to as “Reformulated Gasoline”. Reformulated gasoline contains oxygenates and is specially blended to reduce vehicle emissions and improve air quality. Mitsubishi Motors Corporation strongly supports the use of reformulated gasoline. Properly blended reformulated gasoline has no adverse effect on vehicle performance or on the durabil- ity of the engine and fuel system. MMT (methylcyclopentadienyl manganese tri- carbonyl) MMT is a manganese-containing metallic additive that is blended into some gasolines to increase the octane number. Mitsubishi Motors Corporation recommends using gasolines without MMT. Use of gasolines blended with MMT may adversely affect per- formance, and cause the malfunction indicator on your instru- ment panel to come on. If this happens, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance. Sulfur in gasoline Your vehicle may have been designed to satisfy California’s low-emission regulations based on clean-burning low-sulfur gasoline. Gasoline sold in parts of the country other than Cali- fornia is allowed to have a higher sulfur content. Using such gasoline could adversely affect the vehicle's catalytic converter and cause the engine malfunction indicator (“SERVICE ENGINE SOON” or “CHECK ENGINE”) to come on. Illumi- nation of this indicator while you are using high-sulfur gaso- line does not necessarily mean the vehicle’s emission-control system is malfunctioning. Your authorized Mitsubishi Motors dealer may suggest you try using a different, lower-sulfur brand of unleaded gasoline to determine whether the problem is fuel-related. NOTE G Poor-quality gasoline can cause problems such as poor starting, stalling during idling, abnormal engine noise, and poor acceleration. If you experience any of these prob- lems, try using a different brand of gasoline. If the engine malfunction indicator (“SERVICE ENGINE SOON” or “CHECK ENGINE”) flashes, have the vehicle inspected as soon as possible by the nearest authorized Mitsubishi Motors dealer or a repair facility of your choice. BK0098300US.book 3 ページ ２００８年１２月８日　月曜日　午前１１時３７分

cause deposits to form in the fuel system and engine, resulting in poor starting and poor acceleration. If these problems occur, you are advised to add a detergent addi- tive to the gasoline when you refuel the vehicle. The addi- tive will remove the deposits, thereby returning the engine to a normal condition. Be sure to use a genuine Mitsubishi detergent additive. Using an unsuitable additive could make the engine malfunction. For details, please contact the nearest authorized Mitsubishi Motors dealer. Filling the fuel tank N00301100740 WARNING ! G Gasoline is highly flammable and explosive. You could be burned, seriously injured or killed when handling it. When refueling your vehicle, always turn the engine off and keep away from flames, sparks, and smoking materials. Always handle fuel in well-ventilated outdoor areas. G Before removing the fuel cap, be sure to get rid of your body’s static electricity by touching a metal part of the car or fuel pump. Any static electricity on your body could create a spark that ignites fuel vapor. G Perform the whole refueling process (opening the fuel tank filler door, removing the fuel cap, etc.) by yourself. Do not let any other person come near the fuel tank filler. If you allowed a person to help you and that person was carrying static electricity, fuel vapor could be ignited. G Do not move away from the fuel tank filler until refueling is finished. If you moved away and did something else (for example, sitting on a seat) part- way through the refueling process, you could pick up a fresh charge of static electricity. G Be careful not to inhale fuel vapor. Fuel contains toxic substances. G Keep the doors and windows closed while refueling the vehicle. If they were open, fuel vapor could get into the cabin. BK0098300US.book 4 ページ ２００８年１２月８日　月曜日　午前１１時３７分

17.7 gal (67 L) Refueling 1. Before filling with fuel, stop the engine. 2. The fuel tank filler is located on the rear driver side of your vehicle. To open the fuel tank filler door, hook a finger behind the door, and pull the door toward you. 3. Open the fuel tank filler pipe by slowly turning the cap counterclockwise. A- Remove B- Close WARNING ! G Since the fuel system may be under pressure, remove the fuel tank filler cap slowly. This relieves any pressure or vacuum that might have built up in the fuel tank. If the cap is venting vapor or if you hear a hissing sound, wait until it stops before removing the cap. Otherwise, fuel may spray out, injuring you or others. BK0098300US.book 5 ページ ２００８年１２月８日　月曜日　午前１１時３７分

dling of the fuel filler nozzle. Do not tilt the nozzle. Insert the nozzle in the tank port as far as it will go. 5. When the nozzle stops automatically, do not try to add more fuel. 6. To close, turn the fuel tank filler cap slowly clockwise until you hear clicking sounds, then gently push the fuel tank filler door closed. NOTE G If the fuel tank filler cap is not tight while driving, the engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”) may come on when the onboard diagnostic (OBD) system performs a self check. Always tighten the fuel tank filler cap until you hear click- ing sounds. The indicator will go off after driving several times. If the indicator does not go off, contact your authorized Mitsub- ishi Motors dealer or a repair facility of your choice as soon as possible. CAUTION ! G Your vehicle can only be operated using unleaded gasoline. Serious engine and catalytic converter damage will result if leaded gasoline is used. CAUTION ! G To avoid fuel spillage and overfilling, do not “top- off” the fuel tank. Spilled fuel could discolor, stain, or crack the vehicle’s paintwork. If fuel spills on the paintwork, wipe it off with a soft cloth. WARNING ! G Make sure the fuel cap is securely closed. If the fuel cap is loose, fuel could leak, resulting in a fire. CAUTION ! G If you need to replace the fuel tank filler cap, use only the cap specified for your model vehicle. BK0098300US.book 6 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00301600048 This vehicle should not be modified with non-Mitsubishi Motors genuine parts. Modification with non-Mitsubishi Motors genuine parts could affect its performance, safety or durability, and may even violate regulations. In addition, dam- age or performance problems resulting from the modification may not be covered under warranty. Installation of accessories N00301700023 G The installation of accessories, optional parts, etc., should only be carried out within the limits prescribed by law in the driving area and in accordance with the guidelines and warnings contained within the documents accompanying this vehicle. Only Mitsubishi Motors approved accessories should be fitted to your vehicle. G Improper installation of electrical parts could cause fire. Refer to the “Modification/alterations to the electrical or fuel systems” section within this owner’s manual. G Using a cellular phone or radio set inside the vehicle with- out an external antenna may cause electrical system inter- ference, which could lead to unsafe vehicle operation. G Tires and wheels which do not meet specifications must not be used. Refer to the “Specifications” section for information regarding wheel and tire sizes. CAUTION ! G Before any electrical or electronic accessories are installed, consult an authorized Mitsubishi Motors dealer. BK0098300US.book 7 ページ ２００８年１２月８日　月曜日　午前１１時３７分

provided by different manufacturers in the market, it is not always possible for an authorized Mitsubishi Motors dealer to check whether the attachment or installation of non-Mitsubishi Motors genuine parts will affect the driving safety of your Mit- subishi-vehicle. Modification/alterations to the electrical or fuel systems N00301800040 Mitsubishi Motors manufactures high quality vehicles with an emphasis on safety. It is important that any accessory that is to be fitted, or any modifications carried out which involve the electrical or fuel systems, should be carried out in accordance with Mitsubishi Motors guidelines. WARNING ! G If you choose to use a cellular phone while driving, you must not allow that usage to distract you in the safe operation of your vehicle. Anything, including cellular phone usage, that distracts you from the safe operation of your vehicle increases your risk of an accident. Refer to and follow all state and local laws in your area regarding cellular phone usage while driving. CAUTION ! G Please consult an authorized Mitsubishi Motors dealer concerning any such accessory fitment or modification. If the wires interfere with the vehicle body or improper installation methods are used (protective fuses not included, etc.), electronic devices may be adversely affected, resulting in a fire or other acci- dent. BK0098300US.book 8 ページ ２００８年１２月８日　月曜日　午前１１時３７分

N00301400105 Mitsubishi Motors Genuine Parts are designed and manufac- tured to meet high standards of performance, and are recom- mended for all of your maintenance needs. Also available from your Mitsubishi Motors dealer are a wide variety of accessories to personalize your new vehicle. Each Mitsubishi vehicle has a selection of Mitsubishi Motors authorized accessories to choose from to tailor your new vehicle to your own personal preference. Your Mitsubishi Motors dealer’s Parts Manager has information on various audio systems, protection items, as well as interior and exterior accessories available for your specific model. California Perchlorate Materials Require- ments N00300100017 Certain components of this vehicle, such as airbag modules, seat belt pretensioners, and button cell batteries, may contain perchlorate materials. Special handling may apply. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate. BK0098300US.book 9 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- 2 Seats and restraint systems. . . . . . . . . . . . . . . . . . .2- 3 Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- 4 Rear seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- 11 Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- 12 Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- 13 Seat belt use during pregnancy . . . . . . . . . . . . . . .2- 22 Seat belt pre-tensioner and force limiter systems .2- 22 Child restraints. . . . . . . . . . . . . . . . . . . . . . . . . . . .2- 24 Maintenance and inspection of seat belts. . . . . . . .2- 35 Supplemental Restraint System (SRS) - air bag . .2- 36 BK0098300US.book 1 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Seats N00408400323 1 - Front seats G To adjust the seat forward or backward → P.2-5 G To adjust the seatback → P.2-6 G To adjust the seat height (Driver’s side only) → P.2-7 G To adjust the lumbar support (Driver’s side only) → P.2-9 G For access to the rear seat (Passenger’s side only) → P.2-10 G Heated seats (if so equipped) → P.2-10 2 - Rear seat G Folding the seatbacks forward (ECLIPSE only) → P.2-11 BK0098300US.book 2 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-3 2 Seats and restraint systems N00401600195 Your vehicle has seat belts and other features that help protect you and your passengers in an accident. Seat belts are the most important safety device. When worn properly, seat belts can reduce the chance of serious injury or death in various types of crashes. For added protection during a severe frontal collision, your vehicle has a Supplemental Restraint System (SRS) with air bags for the driver and front seat passenger. The seats, head restraints, and door locks also are safety equipment, which must be used correctly. Always check the following before you drive: G That everyone in your vehicle is properly wearing their seat belt. G That infants and small children are properly secured in appropriate child restraints in the rear seat. G That all doors are fully closed and locked. G That seatbacks are upright. Safety equipment cannot prevent injury or death in all motor vehicle accidents. You can help reduce the risk of injury or death, however, by following the instructions in this manual. BK0098300US.book 3 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Front seats N00401800201 Position the driver’ s seat as far back as possible while main- taining a position that still enables you to fully apply the ped- als, easily control the steering wheel and safely operate the vehicle. Manual seat Power seat WARNING ! G Do not attempt to adjust the seat while driving. This can cause loss of vehicle control and result in an accident. G After adjusting the seat, make sure that the seat is securely locked into position. G To reduce the risk to the driver of serious injury or death during deployment of the driver’s air bag, always properly wear the seat belt and adjust the driver’s seat as far back as possible while maintain- ing a position that still enables you to fully apply the pedals, easily control the steering wheel, and safely operate the vehicle. G To reduce the risk to the front passenger of serious injury or death during deployment of the passen- ger’s air bag, always properly wear the seat belt and adjust the front passenger’s seat as far back as pos- sible. G Always place children 12 years old and under in the rear seat and use appropriate child restraints. BK0098300US.book 4 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-5 2 To adjust the seat forward or backward N00401900260 Manual seat Pull the seat adjusting lever up and slide the seat forward or backward to the desired position. Release the adjusting lever to lock the seat in place. CAUTION ! G Make sure that the seat is adjusted by an adult. If it is adjusted by a child, an unexpected accident might occur. G Do not place a cushion or the like between your back and the seatback while driving. The effectiveness of the head restraints will be reduced in the event of an accident. G When sliding the seats, be careful not to catch your hand or leg. G When sliding or reclining the seat rearward, pay careful attention to the rear seat passengers. WARNING ! G To make sure that the seat is securely locked, try to move it forward or backward without using the adjusting lever. BK0098300US.book 5 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Power seat Push the switch to adjust the seat forward or backward to the desired position. Release the switch, and the seat will lock at that position. NOTE G To prevent the battery from running down, operate the power seat with the engine running. To adjust the seatback N00402000167 To adjust the seatback, lean forward slightly, gently pull the seatback lock lever up, then lean backward to a comfortable position and release the lever. The seatback will lock in place. 1- Forward (towards the front of the vehicle) 2- Backward (towards the rear of the vehicle) CAUTION ! G The reclining mechanism used in the seatback is spring loaded, and will cause the seatback to return quickly to the vertical position when the lock lever is operated. When pulling the lever, sit close to the seatback or hold the seatback with your hand to control its return motion. BK0098300US.book 6 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-7 2 To adjust the seat height (Driver’s side only) N00402100100 Manual seat Turn the dial to raise or lower the whole seat cushion. WARNING ! G To reduce the risk of serious injury or death in the event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehi- cle is in motion. Seat belt performance during an accident can be adversely affected if the seatbacks are reclined. The more a seatback is reclined, the more likely seat belt performance will be adversely affected. If the seat belt is not properly positioned against the body dur- ing an accident, there is increased risk you will slide under the belt and receive serious injury or death. 1- Raise 2- Lower BK0098300US.book 7 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Power seat Front and/or rear parts of the seat cushion height can be adjusted. NOTE G To prevent the battery from running down, operate the power seat with the engine running. Front part of the seat cushion Operate the switch to raise or lower the front part of the seat cushion. Rear part of the seat cushion Operate the switch to raise or lower the rear part of the seat cushion. 1- Raise 2- Lower 1- Raise 2- Lower BK0098300US.book 8 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-9 2 Whole seat cushion Operate the center of the switch to raise or lower the whole seat cushion. To adjust the lumbar support (Driver’s side only) N00402200097 A lumbar support is included in the seatback of the driver’s seat. 1- Raise 2- Lower 1- Strong 2- Weak BK0098300US.book 9 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 For access to the rear seat (Passenger’s side only) N00402400028 For rear seat passenger entry or exit, the front passenger seat and seatback can be moved forward by either pulling up the seat lock lever or depressing the lock release pedal behind the seat. To return the seat, push the seatback backward until you hear a “click” and the seat locks in position. Heated seats (if so equipped) N00435600121 The heated seats can be operated when the ignition key is in the “ON” position. The indicator light (A) will illuminate while the heater is on. WARNING ! G To make sure that the seat is securely locked, try to move it forward or backward without using the adjusting lever. To reduce the risk of serious injury or death in the event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehicle is in motion. 1- Heater high (for quick heating) 2- Heater off 3- Heater low (to keep the seat warm) BK0098300US.book 10 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-11 2 Rear seat N00402500074 Folding the seatbacks forward (ECLIPSE only) N00402900153 The rear seatbacks can be folded forward to provide additional cargo area space. Pull the left and/or right release knobs, and fold the rear seat- backs forward. NOTE G Confirm that the seatback locks securely when it is returned. CAUTION ! G Switch off the seat heaters when not in use. Operate the heaters at high for quick heating. After the seat has become warm, set the heater to low to keep it warm. Slight variations in the seat temperature may be felt while using the heated seats. This is caused by the operation of the heater’s internal thermostat and does not indicate a malfunction. If the following types of persons use the heated seats, they might become too hot or receive minor burns (red skin, heat blisters, etc.): • Children, elderly persons, ill persons • Person with sensitive skin • Excessively fatigued persons • Persons under the influence of alcohol or sleep- inducing medication (cold medicine, etc.) G Do not place heavy objects on the seat or stick pins, needles, or other pointed objects into it. G Do not use a blanket, cushion, or other material with high heat insulation properties on the seat while using the heater; doing so could cause the heater ele- ment to overheat. G When cleaning the seat, do not use benzene, gaso- line, alcohol, or other organic solvents; doing so could damage not only the surface of the seat, but also the heater. G If water or any other liquid is spilled on the seat, allow it to dry thoroughly before attempting to use the heater. Turn the heater off immediately if it appears to be malfunctioning during use. BK0098300US.book 11 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Head restraints N00404300454 The front seats are equipped with padded head restraints (A) integrated with the seatbacks. These head restraints can reduce the risk of a whiplash injury if your vehicle is hit from the rear. To maximize the effectiveness of your head restraint, adjust your seatback to the upright position and sit back against the seatback with your head close to the head restraint. WARNING ! G Do not allow anyone to ride in the cargo area while the vehicle is in motion. People who are not properly seated and restrained can be seriously injured or killed in an accident. G To avoid reducing rearward vision, do not load cargo or luggage higher than the top of the seatback. G Firmly secure cargo and luggage. Unsecured cargo and luggage can move during braking or in an acci- dent, causing serious injury or death. BK0098300US.book 12 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-13 2 Seat belts N00406000282 Seat belts are installed in your vehicle to help reduce the risk of injury to the driver and passenger in the event of an accident. Always use the provided seat belts. Carefully review the following information for proper seat belt usage. WARNING ! G In order to minimize the risk of a neck injury due to a rear impact, the driver and front passenger seat- backs must be adjusted to the upright position before vehicle operation. The driver should never adjust the seat while the vehicle is in motion. G Never place a cushion or similar device on the seat- back. This can adversely affect head restraint per- formance by increasing the distance between your head and the restraint. WARNING ! G To help reduce the risk of injury or death in an acci- dent, seat belts and child restraints must always be used. Refer to “Child restraints” on page 2-24 for additional information. G Never use one seat belt for more than one person. G Never carry more people in your vehicle than there are seat belts. G Always adjust the seat belt for a snug fit. G Always place the shoulder belt over your shoulder and across your chest. Never put it behind you or under your arm. G Always wear the lap belt as low as possible across your hips, not around your waist. G Never modify or alter the seat belts in your vehicle. G To reduce the risk to the driver of serious injury or death during deployment of the driver’s air bag, always properly wear the seat belt and adjust the driver’s seat as far back as possible while maintain- ing a position that still enables you to fully apply the pedals, easily control the steering wheel, and safely operate the vehicle. BK0098300US.book 13 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Seat belt instructions N00406200314 All seats are equipped with a seat belt which uses one com- bined lap-and-shoulder belt with an emergency locking retrac- tor. This system is designed to provide both comfort and safety. It permits full extension and automatic retraction of the belts dur- ing normal vehicle operation. A sensing device inside the belt retractor is designed to lock the retractor in the event of a sud- den change in the vehicle’s motion. NOTE G For instructions on installing a child restraint system using a seat belt, refer to “Installing a child restraint system using the seat belt” on page 2-31. G To reduce the risk to a front seat passenger of seri- ous injury or death from a deploying air bag, make sure the passenger always wears the seat belt prop- erly, remains seated all the way back and upright in their seat, and moves the seat as far back as possible. Refer to “Supplemental Restraint System (SRS) - air bag” on page 2-36 for additional information. G Never hold an infant or child in your arms or on your lap when riding in this vehicle even when you are wearing your seat belt. Never place any part of the seat belt you are wearing around an infant or child. Failure to follow these simple instructions cre- ates a risk of serious injury or death to your child in the event of an accident or sudden stop. G Children 12 years old and under should always ride in the rear seat and be properly restrained. This reduces their risk of serious injury or death in an accident, especially due to a deploying front passen- ger air bag. Refer to “Child restraints” on page 2-24 for additional information. G Any child who is too small to properly wear a seat belt must be properly restrained in an appropriate child restraint system. Children 12 years old and under should be seated only in the rear seat to reduce their risk of serious injury or death in an accident, especially from the deployment of a front passenger air bag. G Infants MUST be placed in a rear-facing child safety seat and positioned in the rear seat. G In the event of an accident, all seat belt assemblies, including retractors and attachment hardware, should be inspected by an authorized Mitsubishi Motors dealer to determine whether replacement is necessary. WARNING ! BK0098300US.book 14 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-15 2 1. Occupants should always sit back in their seats with their backs against the upright seatback. To reduce the risk of serious injury or death during deployment of the air bag, adjust the driver’s seat as far back as possible while main- taining a position that still enables you to fully apply the pedals, easily control the steering wheel, and safely oper- ate the vehicle. The front passenger seat should also be moved as far back as possible. Refer to “Supplemental Restraint System (SRS) - air bag” on page 2-36. Also refer to “To adjust the seat forward or backward” on page 2-5. WARNING ! G To reduce the risk of serious injury or death in the event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehi- cle is in motion. Seat belt performance during an accident can be adversely affected if the seatbacks are reclined. The more a seatback is reclined, the more likely seat belt performance will be adversely affected. If the seat belt is not properly positioned against the body dur- ing an accident, there is increased risk you will slide under the belt and receive serious injury or death. BK0098300US.book 15 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 2. Grasp the latch plate and slide it up the webbing so that it easily pulls across your body. 3. Pull the seat belt out slowly while holding the latch plate. Push the latch plate into the buckle until you hear a “click”. Pull up on the belt to be sure the latch plate is locked securely in the buckle. NOTE G If the seat belt locks up and cannot be pulled out, pull it once with force and let it retract all the way. Then, pull the belt out slowly once again. BK0098300US.book 16 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-17 2 4. The lap part of the belt must always be worn low and snug across the hips. Pull up on the shoulder portion of the belt to take up any slack in the lap belt. NOTE G With the exception of the seat belt for the driver, the seat belts in all other seating positions are equipped with an Automatic Locking Retractor (ALR) function. If you pull the seat belt fully out of the retractor, the retractor will switch to its ALR child restraint installation function (see page 2-31). When the ALR function has been activated, the seat belt will only retract. If this happens, let the belt fully retract, then pull the seat belt back out, repeating steps 1 through 4. 5. To release the belt, press the button on the buckle and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists in the webbing. Then make sure it remains untwisted as it retracts. WARNING ! G Be sure the lap belt portion fits snugly and is worn as low as possible across the hips, not around the waist. Failure to follow this instruction will increase the risk of serious injury or death in the event of an accident. G Be sure the seat belt webbing is not twisted when worn. Twisted webbing may adversely affect seat belt performance. BK0098300US.book 17 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Driver’s seat belt reminder/warning light N00418400137 A tone and warning light are used to remind the driver to fasten the seat belt. When the ignition key is turned to the “ON” position, the warn- ing light will come on and a tone will sound for about 6 sec- onds. If the driver’s seat belt remains unfastened approximately 1 minute later, the warning light will flash and the tone will sound intermittently (12 times each) when the vehicle is driven. If the driver subsequently unfastens the seat belt while driving, the warning light and tone will issue further warnings. And if the seat belt remains unfastened, the warning light and tone will issue further warnings each time the vehicle starts moving from a stop. When the seat belt is fastened, the warnings will stop. WARNING ! G In order to reduce the risk of serious injury or death in an accident, always wear your own seat belt. Do not allow anyone to ride in your vehicle unless he or she is also seated and wearing a seat belt. Children should additionally be restrained in a secure child restraint system. BK0098300US.book 18 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-19 2 Front passenger seat belt warning light N00418300093 The front passenger seat belt warning light is located above the central vents in the instrument panel. The light normally comes on when the ignition switch is turned to the “ON” position and goes off a few seconds later. The light comes on when a person sits on the front passenger seat but does not fasten the seat belt. It goes off when the seat belt is subsequently fastened. Adjustable seat belt shoulder anchor (ECLIPSE only, front seats) N00406300230 To move the anchor down, press the lock knob (A) and slide the anchor down to the desired position. To move the anchor up, slide the anchor up to the desired posi- tion. WARNING ! G Do not install any accessory or sticker that makes the light difficult to see. Anchor down Anchor up BK0098300US.book 19 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Seat belt guide (ECLIPSE SPYDER only, front seats) N00419300032 Each front seat is fitted with a seat belt guide (A). Instruction Insert the seat belt into the seat belt guide through the slot (B). WARNING ! G Always adjust the shoulder belt anchor so that the shoulder belt is positioned across the center of your shoulder without touching your neck. The shoulder belt should not be able to fall off your shoulder. Fail- ure to follow this instruction can adversely affect seat belt performance and increase the risk of seri- ous injury or death in the event of an accident. G Adjust the shoulder belt anchor only when the vehi- cle is not in motion. G Make sure the anchor is securely locked in position after adjusting it. WARNING ! G Always use the seat belt guide so that the shoulder belt is positioned across the center of your shoulder without touching your neck. The shoulder belt should not be able to fall off your shoulder. Failure to follow this instruction can adversely affect seat belt performance and increase the risk of serious injury or death in the event of an accident. BK0098300US.book 20 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-21 2 NOTE G Remove the seat belt from the seat belt guide when a pas- senger is going to move to or from the rear seat. Seat belt extender N00406700087 When your seat belt, even fully extended, is not long enough, a seat belt extender must be obtained. The extender may be used for either of the front seats. G Make sure the part of the seat belt webbing you inserted into the seat belt guide is not twisted. Twisted webbing may adversely affect seat belt per- formance. WARNING ! WARNING ! G The extender should only be used if the existing belt is not long enough. Anyone who can use the stan- dard seat belt should not use an extender. Unneces- sary use of an extender can adversely affect seat belt performance in an accident. G When not required, the extender must be removed and stowed. BK0098300US.book 21 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Seat belt use during pregnancy N00406800075 Seat belts work for everyone, including pregnant women. Like all occupants, pregnant women are more likely to be seriously injured or killed in an accident if they do not wear seat belts. Seat belt pre-tensioner and force limiter systems N00417700319 The driver’s and front passenger’s seats each have a seat belt equipped with a pre-tensioner system. Pre-tensioner system The driver and front passenger seat belts are equipped with a seat belt pre-tensioner system. In moderate-to-severe frontal collisions, this system operates simultaneously with the deployment of the front air bags. The seat belt pre-tensioners are located within the seat belt retractors (A). When activated, the pre-tensioners quickly draw back seat belt webbing and increase seat belt performance. WARNING ! G To reduce the risk of serious injury or death to preg- nant women and unborn children in an accident, pregnant women should always wear a seat belt. The lap portion of the seat belt should be worn snug and low across the hips and below the rounding. Consult your doctor if you have any additional questions or concerns. BK0098300US.book 22 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-23 2 The seat belt pre-tensioner system includes the following com- ponents: The air bag control unit monitors the readiness of the electronic parts of the system whenever the ignition switch is in the “ON” or “START” position. These include all of the items listed above and all related wiring. The pre-tensioner seat belts will operate only when the ignition switch is in the “ON” or “START” position. When the seat belt pre-tensioners activate, some smoke is released and a loud noise will be heard. The smoke is not harm- ful, but care should be taken not to intentionally inhale it, as it may cause some temporary irritation to people with respiratory problems. Even in the event of a severe frontal impact, the pre-tensioners will not operate if the seat belts are not fastened. The seat belt pre-tensioners may not activate in certain frontal collisions, even though the vehicle may appear to be severely damaged. Such non-activation does not mean something is wrong with the seat belt pre-tensioner system, but rather that the collision forces were not severe enough or not of the type to activate the system. 1- SRS warning light 2- Front impact sensors 3- Seat belt pre-tensioners 4- Seat belt buckle switches 5- Air bag control unit WARNING ! G The seat belt pre-tensioner system is designed to work only once. After the seat belt pre-tensioners have been activated, they will not work again. They must promptly be replaced and the entire seat belt pre-tensioner system inspected by an authorized Mitsubishi Motors dealer. BK0098300US.book 23 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 SRS warning light N00408700049 This warning light tells you if there is a problem involving the SRS air bags and the pre-tensioner seat belts. Refer to “SRS warning light” on page 2-44. Force limiter system N00408900070 In the event of an accident, the seat belt force limiter system will help reduce the force applied to the driver and front seat passenger. Child restraints N00407100600 When transporting infants or small children in your vehicle, an appropriate child restraint system must always be used. This is required by law in the U.S. and Canada. Child restraints specifically designed for infants and small chil- dren are offered by several manufacturers. Choose only a child restraint system with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 (FMVSS 213) or Motor Vehicle Restraint Systems and Booster Cushions Safety Regulations (RSSR). Look for the manufacturer’s statement of compliance on the box and child restraint itself. The child restraint system should be appropriate for your child’s weight and height, and should properly fit your vehi- cle’s seat. For detail information, refer to the instruction manual accom- panying the child restraint system. Guidelines for child restraint system selection All children should be properly restrained in a restraint device that offers the maximum protection for their size and age. Be sure to check local, state, or provincial requirements for child size and age that may vary from the recommendations listed below. G Children less than 1 year old and children less than 20 pounds (9 kg) MUST ride in a rear-facing child safety seat that MUST ONLY be used in the rear seat. G Children older than 1 year of age and who weigh less than 40 pounds (18 kg) or who are less than 40 inches (100 cm) tall must be in a forward-facing restraint used only in the rear seat. BK0098300US.book 24 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-25 2 G Children who weigh more than 40 pounds (18 kg) or who are more than 40 inches (100 cm) tall, regardless of age, should use a suitable child seat or a booster seat (including a booster cushion) in the rear seat until the vehicle’s lap/shoulder belt fits them properly. WARNING ! G All children must be seated in the rear seat, and properly restrained. Accident statistics show that children of all sizes and ages are safer when properly restrained in the rear seat, rather than in the front seat. G Any child who is too large to use a child restraint should ride in the rear seat and wear the lap and shoulder belt properly. The shoulder belt must be positioned over the shoulder and across the chest, not across their neck, and with the lap belt posi- tioned low on the child’s hips, not across their stom- ach. If necessary, a booster seat (including a booster cushion) should be used to help achieve a proper seat belt fit. Follow the booster seat (including a booster cushion) manufacturer’s instructions. Only use a booster seat (including a booster cushion) that is certified as complying with Federal Motor Vehicle Safety Standards or Motor Vehicle Restraint Sys- tems and Booster Cushions Safety Regulations. G Your ECLIPSE SPYDER is not equipped with a tether anchor. Child restraint systems and a booster seat (including a booster cushion) which require a tether strap cannot be used in your ECLIPSE SPY- DER. G Never operate the electric convertible top when a child is in your ECLIPSE SPYDER or when a child restraint system is attached to the rear seat. G Never hold an infant or child in your arms or on your lap when riding in this vehicle, even when you are wearing your seat belt. Never place any part of the seat belt you are wearing around an infant or child. Failure to follow these simple instructions cre- ates a risk of serious injury or death to your child in the event of an accident or sudden stop. WARNING ! BK0098300US.book 25 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 WARNING ! G Your vehicle is also equipped with a front passenger air bag. Never put REAR-FACING CHILD RESTRAINTS or INFANT RESTRAINTS in the front passenger seat. This places the infant too close to the passenger air bag. During deployment of the air bag, the infant can be seriously injured or killed. Rear-facing child restraints or infant restraints must only be used in the rear seat. Air bag cover WARNING ! G FRONT-FACING CHILD RESTRAINTS should always be used in the rear seat whenever possible. If one must be used in the front passenger seat, move the seat to the most rearward position and make sure the child stays in the child restraint, properly restrained. Failure to follow these instructions could result in serious injury or death to the child. BK0098300US.book 26 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-27 2 NOTE G Before purchasing a child restraint system, try installing it in the rear seat to make sure there is a good fit. Because of the location of the seat belt buckles and the shape of the seat cushion, it may be difficult to securely install some manufacturer’s child restraint systems. If the child restraint system can be pulled forward or to either side easily on the seat cushion after the seat belt has been tightened, choose another manufacturer’s child restraint system. Depending on the seating position in the vehicle and the child restraint system that you have, the child restraint can be attached using one of the following two methods: • To the lower anchorage in the rear seat ONLY if the child restraint is compatible with the LATCH system (See page 2-28). • To the seat belt (See page 2-31). WARNING ! G It is important to use an approved rear-facing infant restraint until the infant is one year old (unless the infant outgrows the seat sooner). This allows the infant’s neck and spine to develop enough to support the weight of their head in the event of an accident. G When installing a child restraint system, follow the instructions provided by the manufacturer and fol- low the directions in this manual. Failure to do so can result in serious injury or death to your child in an accident or sudden stop. G After installation, push and pull the child restraint system back and forth, and side to side, to see that it is firmly secured. If the child restraint system is not installed securely, it may cause injury to the child or other occupants in the event of an accident or sud- den stop. G When not in use, keep your child restraint system secured with the seat belt, or remove it from the vehicle, in order to prevent it from being thrown around inside the vehicle during an accident. BK0098300US.book 27 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Installing a child restraint system using the LATCH (Lower Anchors and Tethers for chil- dren) system N00418800043 Lower anchor locations The seating positions in the rear seat of your vehicle are equipped with lower anchors for attaching child restraint sys- tems compatible with the LATCH system. NOTE G The symbols on the seatback show the location of the lower anchor points. Tether anchor locations (ECLIPSE only) N00418900086 Your vehicle has 2 attachment points on the floor of the cargo area. These are for securing a child restraint system tether strap to each of the 2 rear seating positions in your vehicle. *- Rear of the vehicle BK0098300US.book 28 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-29 2 Examples of child restraint systems compatible with the LATCH system N00419000101 Using the LATCH system N00419100128 1. Push the anchor connectors (A) on the child restraint sys- tem into the slits (B) in accordance with the instructions provided by the child restraint system manufacturer. Remember, the lower anchors (E) provided with your vehicle are designed to secure suitable child restraint sys- tems compatible with the LATCH system in the rear seat only. A- Rear-facing child restraint B- Front-facing child restraint C- Child restraint system lower anchor connectors D- Tether strap (These are only examples.) A: Connector B: Slit C: Vehicle seatback D: Vehicle seat cushion E: Lower anchor BK0098300US.book 29 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 NOTE G In order to secure a child restraint systems compatible with the LATCH system, use the lower anchor points in the rear seat. It is not necessary to use the vehicle’s seat belt. 2. Open the rear hatch. Remove the rear shelf panel (if so equipped). Refer to “Rear shelf panel” on page 3-180. 3. Cut out the notch (F) in the cargo floor carpet by hand, then lift the carpet. WARNING ! G If there is any foreign material in or around the lower anchors, remove it before installing the child restraint system. Also, make sure the seat belt is away from, not looped through or otherwise inter- fering with, the child restraint system. If foreign matter is not removed and/or the seat belt interferes with the child restraint system, the child restraint system will not be secured properly, could detach and move forward in the event of sudden braking or an accident, and could result in injury to the child or other vehicle occupants. G When the vehicle is moving, do not adjust the seat where the child restraint system is installed. In an ECLIPSE, install a tether strap in accordance with steps 2 to 4 shown hereafter. * - Rear of the vehicle BK0098300US.book 30 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-31 2 4. Latch the tether strap hook (G) of the child restraint sys- tem to the tether anchor (H) and tighten the tether strap so it is securely fastened. NOTE G When using a child restraint system that requires a tether strap, the rear shelf panel cannot be installed. 5. Push and pull the child restraint system in all directions to be sure it is firmly secured. Installing a child restraint system using the seat belt (With emergency/automatic locking mecha- nism) N00407300370 With the exception of the driver, the seat belt in all other seat- ing positions can be converted from normal Emergency Lock- ing Retractor (ELR) mode to Automatic Locking Retractor (ALR) mode. This means that when you pull the seat belt fully out of the retractor, the retractor will switch to its ALR child restraint installation function. Always use the ALR child restraint installation function when you install a child restraint system using the seat belt. Children 12 years old and under should always be restrained in the rear seat, whenever possible, although the front passenger seat belt can also be converted to ALR mode. WARNING ! G Child restraint tether anchors are designed only to withstand loads from correctly fitted child restraint systems. Under no circumstances are they to be used for adult seat belts, or harnesses, or for attaching other items or equipment to the vehicle. WARNING ! G When you install a child restraint system using the seat belt, always make sure the retractor has been switched to the ALR child restraint installation function. The ALR function will keep the child restraint system tightly secured to the seat. Failure to convert the retractor to the ALR function may allow the child restraint system to move for- ward during sudden braking or an accident, result- ing in serious injury or death to the child or other occupants. G [ECLIPSE SPYDER only] Before attaching a child restraint system to the front passenger seat, insert the seat belt into the seat belt guide. Refer to “Seat belt guide” on page 2-20. BK0098300US.book 31 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Installation: 1. Place the child restraint system in a rear seating position. 2. Route the seat belt through the child restraint system according to the instructions provided by the child restraint manufacturer. Then insert the seat belt latch plate into the buckle. Make sure you hear a “click” when you insert the latch plate into the buckle. 3. To activate the ALR child restraint installation function, slowly pull the shoulder part of the belt all the way out of the retractor until it stops. Then let the belt feed back into the retractor. 4. After the belt has retracted, tug on it. If the belt is in the ALR function, you will not be able to pull it out. If the webbing can be pulled out from retractor, the ALR func- tion has not been activated and you will need to repeat steps 3 and 4. BK0098300US.book 32 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-33 2 5. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt allowing the slack to feed into the retractor. Remember, if the lap belt portion is not tight, the child restraint system will not be secure. It may help to put your weight on the child restraint system and/or push on its seatback while pulling up on the belt (see illustration). 6. Open the rear hatch. Remove the rear shelf panel (if so equipped). Refer to “Rear shelf panel” on page 3-180. 7. Cut out the notch (A) in the cargo floor carpet by hand, then lift the carpet. In an ECLIPSE, if your child restraint system requires the use of a tether strap fasten the tether strap in accordance with steps 6 to 8 shown hereafter. * - Rear of the vehicle BK0098300US.book 33 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 8. Latch the tether strap hook (B) of the child restraint sys- tem to the tether anchor (C) and tighten the tether strap so it is securely fastened. NOTE G When using a child restraint system that requires a tether strap, the rear shelf panel cannot be installed. 9. Before putting your child in the restraint, push and pull the restraint in all directions to be sure it is firmly secured. Do this before each use. If the child restraint system is not firmly secure, repeat steps 1 through 8. 10. To remove a child restraint system from the vehicle and deactivate the ALR mode, remove the child from the restraint. Unlatch the buckle. Then remove the belt from the restraint and let the belt fully retract. WARNING ! G Child restraint tether anchors are designed only to withstand loads from correctly fitted child restraint systems. Under no circumstances are they to be used for adult seat belts, or harnesses, or for attaching other items or equipment to the vehicle. BK0098300US.book 34 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-35 2 Children who have outgrown child restraint sys- tems N00407600490 Children who have outgrown a child restraint system should be seated in the rear seat and wear the seat belt. If the shoulder belt crosses their face or neck, and/or the lap belt crosses their stomach, a commercially available booster seat (including a booster cushion) must be used, to raise the child so that the shoulder belt crosses their shoulder and the lap belt remains positioned low across their hips. The booster seat (including a booster cushion) should fit the vehicle seat and have a label certifying compliance with Federal Motor Vehicle Safety Stan- dards or Motor Vehicle Restraint Systems and Booster Cush- ions Safety Regulations. Maintenance and inspection of seat belts N00407000221 The seat belt webbing may be cleaned with mild soap or deter- gent solution. Do not use an organic solvent. Allow the belts to dry in the shade. Do not allow them to retract until completely dry. Do not attempt to bleach or re-dye the belts. The color may rub off and the webbing strength may be affected. Regularly check your seat belt buckles and their release mech- anisms for positive engagement and release of the latch plate. Check the retractors for automatic locking when in the Auto- matic Locking Retractor function. The entire seat belt assembly should be replaced if the webbing shows any obvious cuts, tears, increase in thickness in any sec- tion of the webbing from broken fibers, or severe fading from sunlight. All of these conditions indicate a weakening of the belt, which may adversely affect seat belt performance in an accident. WARNING ! G Any child who is too small to properly wear a seat belt must be properly restrained in an appropriate child restraint system, to reduce their risk of serious injury or death in an accident. G A child should never be left unattended in, or unsu- pervised, around your vehicle. When you leave the vehicle always take the child out as well. G Children can die from heat stroke if left or trapped inside the vehicle, especially on hot days. G Keep your vehicle locked and the trunk (ECLIPSE SPYDER) closed when not in use. Keep your vehicle keys away from children. G For ECLIPSE SPYDER, never allow children to play in the trunk of your vehicle. WARNING ! G Do not attempt to repair or replace any part of the seat belt assemblies. This work should be done by an authorized Mitsubishi Motors dealer. Failure to have an authorized Mitsubishi Motors dealer per- form the work could reduce the effectiveness of the belts and could result in a serious injury or death in an accident. BK0098300US.book 35 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Supplemental Restraint System (SRS) - air bag N00407700606 This vehicle is equipped with a Supplemental Restraint System (SRS), which includes air bags for the driver and front passen- ger. The SRS front air bags are designed to supplement the primary protection of the driver and front passenger seat belt systems by providing those occupants with protection against head and chest injuries in certain moderate to severe frontal collisions. The SRS front air bags, together with the sensors at the front of the vehicle and sensors attached to the front seats, form an advanced air bag system. In an ECLIPSE, the SRS side air bags are also designed to sup- plement the seat belts and provide the driver and front passen- ger with protection against chest and abdomen injuries in certain moderate to severe side impact collisions. In an ECLIPSE SPYDER, the SRS side air bags are also designed to supplement the seat belts and provide the driver and front passenger with protection against head and chest injuries in certain moderate to severe side impact collisions. The SRS curtain air bags (ECLIPSE only) are designed to sup- plement the seat belts and provide the driver and front passen- ger with protection against head injuries in certain moderate to severe side impact collisions. The SRS air bags are NOT a substitute for use of the seat belts. For maximum protection in all types of accidents, seat belts must ALWAYS be worn by everyone who drives or rides in this vehicle (with infants and small children in an appropriate child restraint in the rear seat, and older children buckled in the rear seat). Refer to “Child restraints” on page 2-24. WARNING ! G IT IS VERY IMPORTANT TO ALWAYS WEAR YOUR SEAT BELT PROPERLY EVEN WITH AN AIR BAG. • Seat belts help keep the driver and front passenger properly positioned. This reduces the risk of injury in all collisions, and reduces the risk of serious injuries or death when the air bags inflate. During sudden braking just before a collision, an unrestrained or improperly restrained driver or front passenger can move forward into direct con- tact with, or within close proximity to, the air bag when it begins to inflate. The beginning stage of air bag inflation is the most forceful and can cause serious injuries or death if the occupant comes in contact with the air bag at this time. • Seat belts reduce the risk of injury in rollovers, rear impact collisions, and in lower-speed frontal collisions, because the air bags are not designed to inflate in those situations. • Seat belts reduce the risk of being thrown from your vehicle in a collision or rollover. BK0098300US.book 36 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-37 2 WARNING ! G IT IS VERY IMPORTANT TO BE PROPERLY SEATED. • A driver or front passenger sitting too close to the steering wheel or instrument panel during air bag deployment can be seriously injured or killed. • Air bags inflate very quickly and with great force. If the driver and front passenger are not properly seated and restrained, the air bag may not provide the proper protection and can cause serious inju- ries or death when it inflates. • To reduce the risk to the driver of serious injury or death due to a deploying driver’s air bag, always properly wear your seat belt and adjust the driver’s seat as far back as possible, maintaining a position that still allows the driver to have good control of the steering wheel, brake, accelerator, and other vehicle controls. • To reduce the risk to the front passenger of serious injury or death from a deploying passenger’s air bag, make sure the passenger always wears the seat belt properly, remains seated upright and all the way back in the seat, and positions the seat as far back as possible. WARNING ! G Air bags inflate very quickly and with great force. Do not sit on the edge of the seat or lean your head or chest close to the steering wheel or the instrument panel. G Do not put your feet or legs on or against the instru- ment panel. BK0098300US.book 37 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 WARNING ! G Infants and small children should never ride unre- strained, or lean against the instrument panel. They should never ride held in your arms or on your lap. They can be seriously injured or killed in an acci- dent, especially when the air bags inflate. Infants and children should be properly seated in the rear seat in an appropriate child restraint system. Refer to “Child restraints” on page 2-24. WARNING ! G NEVER put REAR-FACING CHILD RESTRAINTS or INFANT RESTRAINTS in the front passenger seat. This places the infant too close to the passenger air bag. During deployment of that air bag, the infant can be seriously injured or killed. Rear-facing child restraints or infant restraints must only be used in the rear seat. Air bag cover BK0098300US.book 38 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-39 2 How the Supplemental Restraint System works N00407800317 The SRS includes the following components: WARNING ! G FRONT-FACING CHILD RESTRAINTS should be used in the rear seat whenever possible. If they must be used in the front passenger seat, move the seat to the most rearward position and make sure the child stays in the child restraint, properly restrained. Fail- ure to follow these instructions could result in seri- ous injury or death to the child. WARNING ! G Older children should be seated in the rear seat with their seat belt properly worn, and with an appropri- ate booster seat (including a booster cushion) if needed. Refer to “Children who have outgrown child restraint systems” on page 2-35. 1- Driver’s air bag 2- SRS warning light 3- Passenger’s air bag off indicator 4- Passenger’s front air bag 5- Front impact sensors 6- Driver’s seat position sensor 7- Passenger’s seat weight sensors 8- Air bag control unit BK0098300US.book 39 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 The air bag control unit monitors the readiness of the electronic parts of the system whenever the ignition switch is in the “ON” or “START” position. These include all of the items listed above and all related wiring. The air bags will operate only when the ignition switch is in the “ON” or “START” position. When the impact sensors detect a sufficient front or side impact to deploy the air bag(s), the appropriate air bag(s) will be deployed. When air bags deploy, some smoke is released accompanied by a loud noise. The smoke is not harmful, but do not intentionally inhale the smoke as it may cause temporary irritation to people with respiratory problems. After deployment, the air bags will quickly deflate, so quickly that some people may not even realize the air bags inflated. Air bag inflation does not prevent the driver from seeing or being able to steer the vehicle, and does not prevent people from leaving the vehicle. 9- Side air bag modules 10- Curtain air bag modules (ECLIPSE only) 11- Side impact sensors CAUTION ! G Air bags inflate very quickly and with great force. In certain situations, contact with an inflating air bag may cause small cuts, abrasions, and bruises. BK0098300US.book 40 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-41 2 Event Data Recording N00418600054 Your vehicle is equipped with an “EDR” - Event Data Recorder which is capable of collecting and storing data in the event of an air bag deployment. The EDR may record the following information: G Condition of specific vehicle systems; G Whether the driver and front passenger seat belts were buckled; G Diagnostic code(s) Driver’s seat position sensor N00417900092 The driver’s seat position sensor is attached to the seat rail and provides the air bag control unit with information on the seat’s fore-aft position. The air bag control unit controls deployment of the driver’s front air bag in accordance with the information it receives from this sensor. If there is a problem involving the driver’s seat position sensor, the SRS warning light in the instrument panel will come on. Refer to “SRS warning light” on page 2-44. WARNING ! G If the SRS warning light comes on, have the vehicle inspected by an authorized Mitsubishi Motors dealer as soon as possible. G Please observe the following instructions to ensure that the driver’s seat position sensor can operate correctly. • Adjust the seat to the correct position, and sit well back against the seatback. Refer to “Front seat” on page 2-4. • Do not recline the seatback more than necessary when driving. • Do not place metallic objects or luggage under the front seat. G If the vehicle is involved in a severe impact, have the sensor inspected by an authorized Mitsubishi Motors dealer as soon as possible. BK0098300US.book 41 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Passenger’s seat weight sensors N00418000221 The passenger’s seat weight sensors are attached to the seat rails and provide the air bag control unit with information regarding the weight on the front passenger seat. The air bag control unit controls deployment of the passenger’s front air bag in accordance with the information it receives from this sensor. The passenger’s front air bag will not deploy in an impact when the weight on the seat is sensed to be less than approxi- mately 66 pounds (30 kg). In this case, the passenger air bag off indicator will come on. Refer to “Passenger air bag off indicator” on page 2-43. If there is a problem involving the passenger seat weight sen- sors, the SRS warning light in the instrument panel will come on. Refer to “SRS warning light” page 2-44. WARNING ! G If any of the following conditions occur, you should immediately have your vehicle inspected by an authorized Mitsubishi Motors dealer as soon as pos- sible: • The SRS warning light does not initially come on when the ignition key is turned to the “ON” or “START” position. • The SRS warning light does not go out after sev- eral seconds. • The SRS warning light comes on while you are driving. G To ensure that the passenger’s seat weight sensors can correctly sense the weight being applied to the seat, observe the following instructions. Failure to follow these instructions can adversely affect the performance of the passenger’s air bag system. • Adjust the seat to the correct position, and sit well back against the seatback. Refer to “Front seat” on page 2-4. • Do not recline the seatback more than necessary. • Never have more than one person (adult or child) sitting on the seat. • Do not place anything between the seat and the floor console. • Do not hang anything on the front passenger’s seatback. • When attaching a child restraint system, secure it firmly. • Do not place luggage or other objects on the seat. • Do not use a seat cover or a cushion. • Do not modify or replace the seat and seat belt. • Do not place luggage or other objects under the seat. • Do not place the floor mat on the seat rails. • Do not expose the sensors to liquids or vapors. • Do not subject the sensors to shock. • Do not allow rear-seat occupants to push the front passenger seat with their feet or force the front passenger seat upward. • Do not allow rear-seat occupants to grasp the front passenger’s seatback or put their arms around it. • When attaching a child restraint system in the rear seat, make sure it does not interfere with the front seat. • When using the wind deflector, adjust the seat to the position where the seat does not come in con- tact with the wind deflector. (ECLIPSE SPYDER only) WARNING ! BK0098300US.book 42 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-43 2 Passenger’s air bag off indicator N00418100219 The passenger air bag off indicator is located in the instrument panel. The indicator normally comes on when the ignition switch is turned to the “ON” position and goes out a few seconds later. [For ECLIPSE] In the following situations, the indicator will stay on to show that the passenger’s front air bag is not operational. G The passenger’s seat weight sensors sense a weight of less than approximately 66 pounds (30 kg) on the front passen- ger seat. G The front passenger’s seat is not occupied. When the weight applied to the front passenger seat is sensed to be approximately 66 pounds (30 kg) or greater, the indicator goes out to show that the passenger’s front air bag is opera- tional. G If the vehicle is involved in a severe impact, have the sensors inspected by an authorized Mitsubishi Motors dealer as soon as possible. WARNING ! BK0098300US.book 43 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 [For ECLIPSE SPYDER] In the following situations, the indicator will stay on to show that the passenger’s front air bag and the passenger’s side air bag are not operational. G The passenger’s seat weight sensors sense a weight of less than about 66 pounds (30 kg) on the front passenger seat. G The front passenger’s seat is not occupied. When the weight applied to the front passenger seat is sensed as about 66 pounds (30 kg) or greater, the indicator goes off to show that the passenger’s front air bag and the passenger’s side air bag are operational. SRS warning light N00408300306 There is a Supplemental Restraint System (SRS) warning light on the instrument panel. The system checks itself each time the ignition is turned on. When the ignition key is in the “ON” or “START” position, the SRS warning light should come on for several seconds and then go out. This means the system is working properly. If there is a problem involving one or more of the SRS compo- nents, the warning light will come on and stay on. The SRS warning light is shared by the Supplemental Restraint System (SRS) and the seat belt pre-tensioner system. WARNING ! G If any of the following conditions occur, you should immediately have the air bag system in your vehicle inspected by an authorized Mitsubishi Motors dealer as soon as possible: • The passenger’s air bag off indicator comes on when an adult is sitting on the front passenger seat. • The passenger’s air bag off indicator does not come on when the front passenger’s seat is not occupied. • The passenger’s air bag off indicator does not come on when the ignition switch is turned to the “ON” position. • The passenger’s air bag off indicator comes on and goes out repeatedly. G Do not attach any accessory to your vehicle that makes the passenger’s air bag off indicator difficult or impossible to see. You must be able to see the passenger’s air bag off indicator and verify the status of the passenger’s air bag system. BK0098300US.book 44 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-45 2 Driver’s and passenger’s front air bag system N00407900220 The driver’s air bag is located under the padded cover in the middle of the steering wheel. The front passenger’s air bag is contained in the instrument panel above the glove compart- ment. The driver’s air bag and the front passenger’s air bag are designed to deploy at the same time. However, the front pas- senger’s air bag does not deploy when the front passenger seat is not occupied or when the weight sensor in the front passen- ger seat senses a weight on the seat of less than approximately 66 pounds (30 kg). WARNING ! G If any of the following conditions occur, the SRS and/or seat belt pre-tensioners are not working properly and you should immediately have it inspected by an authorized Mitsubishi Motors dealer: • The SRS warning light does not come on when the ignition key is turned to the “ON” or “START” position. • The SRS warning light does not go out after sev- eral seconds. • The SRS warning light comes on while driving. Driver Front passenger BK0098300US.book 45 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Deployment of front air bags N00408000459 The front air bags ARE DESIGNED TO DEPLOY when… The front air bags are designed to deploy when the vehicle suf- fers a moderate to severe frontal impact. A typical condition is shown in the illustration to the left. The front air bags are designed to deploy only in certain mod- erate to severe frontal collisions within the shaded area between the arrows in the illustration to the right. The front air bags will deploy if the impact to the vehicle’s main structure is above a specific threshold level. The thresh- old level is approximately 15 mph (25 km/h) for a frontal colli- sion straight into a solid flat wall that does not bend or deform. If the impact to the vehicle’s main structure is below this threshold level, the front air bags may not deploy. This thresh- old level may also be higher if the vehicle hits something that absorbs the impact, either by bending or moving (for example, another stationary vehicle, a pole or a guard rail). The beginning stage of air bag inflation is the most forceful, and can cause serious injuries or death if you are too close to the deploying air bag. Accordingly, it is important that you always wear the available seat belt. Head-on collision with a solid wall at speeds of approx. 15 mph (25 km/h) or higher Moderate to severe frontal impact within the shaded area between the arrows BK0098300US.book 46 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-47 2 The front air bags MAY NOT DEPLOY when … In certain types of front collisions, the front air bags may not deploy, even if the deformation of the body seems to be large, because the vehicle’s body structure is designed to absorb the impact and deform in order to help protect the occupants. Some typical situations where the front air bags may not deploy are shown in the illustrations. Because the front air bags do not protect the occupant in all types of frontal collisions, be sure to always wear your seat belts properly. Collision with a utility pole, tree or other narrow objects Collision where the vehicle slides under the rear body of a truck Oblique frontal impact BK0098300US.book 47 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 The front air bags ARE NOT DESIGNED TO DEPLOY when … The front air bags are not designed to deploy in situations where they cannot provide protection to the occupants. Some typical situations are shown in the illustrations. Because the front air bags do not protect the occupants in all types of collisions, be sure to always wear your seat belts prop- erly. Rear end collision to your vehicle Side collision to your vehicle Vehicle rolls onto its side or roof BK0098300US.book 48 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-49 2 The front air bags MAY DEPLOY when … The front air bags may deploy if the underside of the vehicle suffers a moderate to severe impact (undercarriage impact). Some typical situations are shown in the illustrations. Because the front air bags may deploy in certain types of unex- pected impacts, as shown in the illustrations, and these unex- pected impacts can move you out of position, it is important to always wear your seat belts properly. When worn properly, seat belts can help maintain your distance from the air bags when they begin to inflate. The beginning stage of air bag inflation is the most forceful and can cause serious injury or death if you are close to the deploying air bag. Collision with an elevated median/island or curb Vehicle travels over a deep hole/pothole Vehicle drives down a steep slope and hits the ground BK0098300US.book 49 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 WARNING ! G Do not attach anything to the steering wheel’s pad- ded cover, such as trim material, badges, etc. These could strike and injure an occupant if the air bag inflates. G Do not set anything on, or attach anything to, the instrument panel above the glove compartment. Such items could strike and injure an occupant if the air bag inflates. WARNING ! G Do not attach accessories to, or put them in front of, the windshield. They could restrict the air bag infla- tion, or strike and injure an occupant, when the air bag inflates. G Do not place objects, such as packages or pets, between the air bags and the driver or the front pas- senger. Such objects can adversely affect air bag performance, or cause serious injury or death when the air bag deploys. G Immediately after air bag inflation, some parts of the air bag system will be hot. Do not touch them. You could be burned. G The air bag system is designed to work only once. After the air bags deploy, they will not work again. They must promptly be replaced and the entire air bag system must be inspected by an authorized Mit- subishi Motors dealer. BK0098300US.book 50 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-51 2 Side air bag system N00408100290 The side air bags (A) are contained in the driver and front pas- senger seatbacks. [For ECLIPSE] The side air bag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat. [For ECLIPSE SPYDER] The side air bag is designed to inflate only on the side of the vehicle that is impacted. In the following situations, the passenger’s side air bag is not operational. G The passenger’s seat weight sensors sense a weight of less than about 66 pounds (30 kg) on the front passenger seat. G The front passenger’s seat is not occupied. ECLIPSE ECLIPSE SPYDER BK0098300US.book 51 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 A label is attached to the seatbacks in vehicles with side air bags. Curtain air bag system (ECLIPSE only) N00419200028 The curtain air bags are contained in the front and rear pillars and roof side rail. The curtain air bag is designed to inflate only on the side of the vehicle that is impacted, even with no passen- ger in the front seat. BK0098300US.book 52 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-53 2 WARNING ! G The side air bag and curtain air bag can cause seri- ous injury or death to anyone too close to the air bag when it deploys. To reduce the risk of injury from a deploying side air bag and curtain air bags, driver and front passenger must be properly restrained and seated well back, upright, and in the middle of the seat. Do not lean against the door. WARNING ! G In order to reduce the risk of injury from a deploy- ing side air bag, do not allow any rear seat passen- gers to hold onto the back of either front seat. Special care should be taken with children. G Do not place any objects near or around the front of either front seatback. Such objects can interfere with proper side air bag deployment and cause injury during deployment of the side air bag. G Do not place stickers, labels or additional trim on the back of either front seat. They can interfere with proper side air bag deployment. G Do not install seat covers or re-cover seats that have side air bags. Covers can interfere with proper side air bag deployment and adversely affect side air bag performance. BK0098300US.book 53 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 WARNING ! G Do not attach a microphone (A) or any other object around the part where the curtain air bag (B) deploys, such as on the windshield, side door glass or front and rear pillars and roof side rail. When the curtain air bag inflate, the microphone or other object may be hurled with great force or the curtain air bag may not inflate correctly, resulting in death or serious injury. WARNING ! G Do not put a hanger or any heavy or pointed object on the coat hook. If the curtain air bag was acti- vated, any such item could be propelled away with great force and could prevent the curtain air bag from inflating correctly. Hang clothes directly on the coat hook (without using a hanger). Make sure there are no heavy or sharp objects in the pockets of clothes that you hang on the coat hook. G Never install a rear-facing child restraint in the front passenger seat. Rear-facing child restraints MUST ONLY be used in the rear seat. G Front-facing child restraints should also be used ONLY in the rear seat. If a front-facing child restraint must be used in the front passenger seat, move the seat as far back as possible, and make sure that the child stays in the child restraint, properly restrained and away from the door. G Do not allow a child to lean against or sit close to the passenger door, even if the child is seated in a child restraint system. The child’s head should also not lean against or be close to the section of the seatback where the side air bag and curtain air bag are located. It is dangerous if the side air bag and cur- tain air bag deploys. Failure to follow all of these instructions could lead to serious injury or death to the child. G Work done on or in the vicinity of the side air bag and curtain air bag system components should be done only by an authorized Mitsubishi Motors dealer. Improper work methods can cause acciden- tal side air bag and curtain air bag deployment, or render a side air bag and curtain air bag inoperable. Either of these situations can result in serious injury or death. BK0098300US.book 54 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-55 2 Deployment of side air bag and curtain air bag N00408200392 The side air bag and curtain air bag ARE DESIGNED TO DEPLOY when … A side air bag and curtain air bag are designed to deploy when the vehicle suffers a moderate to severe side impact to the mid- dle of the passenger compartment. The typical situation is shown in the illustration. The seat belts in your vehicle are your primary means of pro- tection in an accident. The SRS (Supplemental Restraint Sys- tem) side air bags and curtain air bags are designed to provide additional protection. Therefore, for your safety and the safety of all occupants, be sure to always wear your seat belts prop- erly. The side air bag and curtain air bag MAY NOT DEPLOY when … In certain types of side collisions, the side air bag and curtain air bag may not deploy, even if the deformation of the body seems to be large, because the vehicle’s body structure is designed to absorb the impact and to deform in order to help protect the occupants. Some typical situations where the side air bag and curtain air bag may not deploy are shown in the illustrations. Because the side air bags and curtain air bags do not protect the occupant in all types of side collisions, be sure to always wear your seat belts properly. Moderate to severe impact to the middle of the vehicle body’s side structure BK0098300US.book 55 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 Side impact in an area away from the passenger compartment Motorcycle or other similar small vehicle collision with the side of vehicle Collision with a utility pole, tree or other narrow object Oblique side impact Vehicle rolls onto its side or roof BK0098300US.book 56 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-57 2 The side air bag and curtain air bag ARE NOT DESIGNED TO DEPLOY when … The side air bag and curtain air bag are not designed to deploy in situations where they cannot provide protection to the occu- pants. Some typical situations are shown in the illustrations. Because the side air bags and curtain air bags do not protect the occupants in all types of collisions, be sure to always wear your seat belts properly. SRS servicing N00408500627 Head-on collision Rear end collision WARNING ! G Any maintenance performed on or near the compo- nents of the SRS should be performed only by an authorized Mitsubishi Motors dealer. Do not permit anyone else to do any service, inspection, mainte- nance or repair on any SRS components or wiring. Similarly, no part of the SRS should ever be han- dled, removed or disposed by anyone except an authorized Mitsubishi Motors dealer. Improper work methods on the SRS components or wiring could result in an accidental air bag deploy- ment or could make the SRS inoperable. Either of these situations could result in serious injury or death. G Do not modify your steering wheel or any other SRS component or related vehicle part. For example, replacement of the steering wheel, or modifications to the front bumper or body structure can adversely affect SRS performance and may lead to injury. G If your vehicle has received any damage, you should have the SRS inspected by an authorized Mitsubishi Motors dealer to make sure it is in proper working order. G Do not modify your front seats, center pillar or cen- ter console. Such modifications can adversely affect SRS performance and may lead to injury. Also, if you discover any tear or open seam in the seat fabric near the side air bag, have the seat inspected by an authorized Mitsubishi Motors dealer. BK0098300US.book 57 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2 NOTE G When you transfer ownership of the vehicle to another person, we urge you to alert the new owner that it is equipped with the SRS and refer that owner to the applica- ble sections in this owner’s manual. G If you decide to junk or scrap your vehicle, we urge you to first take it to an authorized Mitsubishi Motors dealer so that the SRS can be made safe for disposal. G If any of the following parts needs to be modified for use by a handicapped person, the advanced air bag system will be greatly affected. Please consult an authorized Mit- subishi Motors dealer. • Driver’s seat • Front passenger seat • Front seat belt • Steering wheel • Instrument panel G For ECLIPSE, if you find a crack in or damage to the front pillar, rear pillar, or roof side rail where the curtain air bag is located, have the SRS inspected by an authorized Mitsubishi Motors dealer. WARNING ! [For vehicles sold in U.S.A.] To contact Mitsubishi Motors North America, Inc. call 1-888-648-7820 or write to: Mitsubishi Motors North America, Inc. Customer Relations Department P. O. Box 6400 Cypress, CA 90630-0064 [For vehicles sold in Canada] To contact Mitsubishi Motor Sales of Canada, Inc. call 1-888-576-4878 or write to: Mitsubishi Motor Sales of Canada, Inc. Customer Relations Department P.O. Box 41009 4141 Dixie Road Mississauga, ON L4W 5C9 [For vehicles sold in Puerto Rico] To contact Mitsubishi Motor Sales of Caribbean, Inc. call 1-800-981-0452 or write to: Mitsubishi Motor Sales of Caribbean, Inc. Customer Service Department P.O. Box 192216 SAN JUAN PR 00919-2216 BK0098300US.book 58 ページ ２００８年１２月８日　月曜日　午前１１時３７分

2-59 2 Warning labels N00408600282 Occupant restraint warning labels for the SRS are located in the vehicle as shown in the illustration. * - Located in the passenger’s side as well. BK0098300US.book 59 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Break-in recommendations . . . . . . . . . . . . . . . . . .3- 2 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 2 Electronic immobilizer (Anti-theft starting system). . . . . . . . . . . . . . . . .3- 3 Keyless entry system . . . . . . . . . . . . . . . . . . . . . . .3- 7 Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 13 Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . .3- 15 Rear hatch (ECLIPSE)/Trunk lid (ECLIPSE SPYDER) . . . . . . . . . . . . . . . . . . . . .3- 16 Inside rear hatch/trunk lid release . . . . . . . . . . . . .3- 18 Inside emergency trunk lid release (ECLIPSE SPYDER) . . . . . . . . . . . . . . . . . . . . .3- 20 Theft-alarm system . . . . . . . . . . . . . . . . . . . . . . . .3- 22 Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 26 Sunroof (ECLIPSE only, if so equipped). . . . . . . .3- 28 Electric convertible top (ECLIPSE SPYDER) . . .3- 31 Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 54 Steering wheel tilt lock lever . . . . . . . . . . . . . . . . .3- 55 Inside rearview mirror . . . . . . . . . . . . . . . . . . . . . .3- 56 Outside rearview mirrors . . . . . . . . . . . . . . . . . . . .3- 59 Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 61 Steering wheel lock . . . . . . . . . . . . . . . . . . . . . . . .3- 63 Starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 64 Manual transaxle . . . . . . . . . . . . . . . . . . . . . . . . . .3- 67 Automatic transaxle . . . . . . . . . . . . . . . . . . . . . . . .3- 72 Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 81 Anti-lock braking system. . . . . . . . . . . . . . . . . . . .3- 82 Active stability control (ASC) . . . . . . . . . . . . . . . .3- 85 Power steering system . . . . . . . . . . . . . . . . . . . . . .3- 90 Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 91 Tire pressure monitoring system . . . . . . . . . . . . . . 3- 97 Rear-view camera (if so equipped) . . . . . . . . . . . . 3-104 Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . . . 3-106 Indicator and warning light package . . . . . . . . . . . 3-112 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-113 Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-113 Multi center display. . . . . . . . . . . . . . . . . . . . . . . . 3-116 Combination headlights and dimmer switch. . . . . 3-127 Headlight levelling switch (if so equipped) . . . . . 3-130 Turn signal lever . . . . . . . . . . . . . . . . . . . . . . . . . . 3-131 Hazard warning flasher switch . . . . . . . . . . . . . . . 3-132 Front fog light switch (if so equipped) . . . . . . . . . 3-133 Wiper and washer switch . . . . . . . . . . . . . . . . . . . 3-134 Electric rear window defogger switch. . . . . . . . . . 3-137 Horn switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-138 Hands-free Bluetooth® cellular phone interface system with voice recognition (if so equipped). 3-139 Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-168 Vanity mirror (if so equipped). . . . . . . . . . . . . . . . 3-169 Power outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-170 Interior lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-170 Glove compartment. . . . . . . . . . . . . . . . . . . . . . . . 3-177 Floor console box . . . . . . . . . . . . . . . . . . . . . . . . . 3-178 Cup holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-179 Rear shelf panel (ECLIPSE only, if so equipped). 3-180 Coat hooks (ECLIPSE only, if so equipped). . . . . 3-181 Luggage hooks (ECLIPSE only). . . . . . . . . . . . . . 3-182 BK0098300US.book 1 ページ ２００８年１２月８日　月曜日　午前１１時３７分

3 Break-in recommendations N00508700226 Advanced automobile manufacturing techniques permit you to operate your new vehicle without requiring a long break-in period of low-speed driving. However, you can add to the future performance and economy of your vehicle by observing the following precautions during the first 300 miles (500 km). Drive your vehicle at moderate speeds during the break-in period. G Avoid revving the engine. G Avoid rough driving such as fast starts, sudden accelera- tion, prolonged high-speed driving and sudden braking. These would have a detrimental effect on the engine and also cause increased fuel and oil consumption, which could result in malfunction of the engine components. Be particularly careful to avoid full acceleration while in low gear. G Do not overload the vehicle. Observe the seating capacity (See “Cargo load precautions” on page 4-12). G Do not use this vehicle for trailer towing. Keys N00508800445 Two keys are provided. The keys fit all locks. Keep one in a safe place as a spare key. BK0098300US.book 2 ページ ２００８年１２月８日　月曜日　午前１１時３７分

3-3 3 NOTE G The key number (A) is stamped on the key number plate as shown in the illustration. Make a record of the key number and store the key and key number plate in separate places, so that you can order a key from your authorized Mitsubishi Motors dealer if the original keys are lost. G The key is a precision electronic device with a built-in sig- nal transmitter. Please observe the following in order to prevent damage. • Do not leave where it may be exposed to heat caused by direct sunlight, such as on top of the dashboard. • Do not take the remote control transmitter apart. • Do not excessively bend the key or subject it to strong impacts. • Keep the remote control transmitter dry. • Keep away from magnetic objects such as key holders. • Keep away from devices that produce magnetism, such as audio systems, computers and televisions. • Do not clean with ultrasonic cleaners. • Do not leave the key where it may be exposed to high temperature or high humidity. G As your vehicle is equipped with an electronic immobi- lizer, the engine is designed so that it will not start if the ID code registered in the immobilizer computer and the key’s ID code do not match. Refer to the section entitled “Electronic immobilizer” for details and key usage. Electronic immobilizer (Anti-theft starting system) N00509100676 The electronic immobilizer is designed to significantly reduce the possibility of vehicle theft. The purpose of the system is to immobilize the vehicle if an invalid start is attempted. A valid start attempt can only be achieved (subject to certain condi- tions), using a key “registered” to the immobilizer system. All of the keys provided with your new vehicle have been pro- grammed to the vehicle’s electronics. BK0098300US.book 3 ページ ２００８年１２月８日　月曜日　午前１１時３７分

3 NOTE G In the following cases, the vehicle may not be able to rec- ognize the registered ID code from the key. This means the engine will not start even when the registered key is turned to the “START” position. • When the key contacts a key ring or other metallic or magnetic object (Type A) • When the key grip contacts metal of another key (Type B) • When the key contacts or is close to other immobilizing keys (including keys of other vehicles) (Type C) G In cases like the above, move the offending object(s) away from the key and turn the key back to the “ACC” or “LOCK” position. Then try to start the engine again. If the engine does not start, contact an authorized Mitsubishi Motors dealer. BK0098300US.book 4 ページ ２００８年１２月８日　月曜日　午前１１時３７分

3-5 3 NOTE G Electronic immobilizer is not compatible with commer- cially available remote starting systems. Use of commer- cially available remote starting systems may result in vehicle starting problems and a loss of security protection. G A system failure is suspected when the ignition key is turned to the “START” position, and the engine does not start. In such a case, contact an authorized Mitsubishi Motors dealer. Replacement keys Only keys that have been programmed to the vehicle electron- ics can be used to start the vehicle. If you lose a key, you can order a key from your authorized Mitsubishi Motors dealer by referring to the key number. To prevent vehicle theft, the ID code for the vehicle keys must be changed. Take your vehicle and all remaining keys to your authorized Mitsubishi Motors dealer to have your ID code changed. Additional keys To add a key, you need to register the ID code to the vehicle. Registering the ID code can be done by your authorized Mit- subishi Motors dealer. Or it can be done by yourself (except for vehicles sold in Canada). For you to register the ID code yourself, follow the “Customer key programming” procedure below. If you choose to have your authorized Mitsubishi Motors dealer register the ID code, take your vehicle and any remain- ing keys to your authorized Mitsubishi Motors dealer. NOTE G You are provided with 2 keys, but you may add up to 6 more keys. Customer key programming (Except for vehicles sold in Canada) You can program new keys to the system if you have two valid (already registered) keys and blank (not registered) immobi- lizer key (specially cut for your vehicle at your Mitsubishi Motors dealer) by doing the following: 1. Insert the first valid key into the ignition and turn the igni- tion to the “ON” position for 5 seconds. 2. Turn the ignition to the “LOCK” position and remove the first key. 3. Within 30 seconds of turning the first key to the “LOCK” position, insert the second valid key into the ignition and turn it to the “ON” position. About 10 seconds later, the immobilizer indicator will start blinking. CAUTION ! G Do not make any alterations or additions to the immobilizer system. Alterations or additions could cause failure of the immobilizer. BK0098300US.book 5 ページ ２００８年１２月８日　月曜日　午前１１時３７分