Acclaim Lighting AL-Dimmer-1 PRO User Instructions

DMX ADDRESS SETTING DMX IN DMX OUT AL-DIMMER-1 PRO 1 1 2 2 4 4 8 8 16 16 32 32 64 64 128 128 256 Dim Addr Load ( 6A) max Analog GND +12-24V +12-24V GND GND 0-10V IN On Off DESCRIPTIONS 24-004-2461-00 Rev 1.1 Congratulations with your purchase of this product. Check for transport damage. You should be in possession of the following items: 1 AL-Dimmer-1 PRO 1 Manual, 1 Screwdriver & 1 Connecting part Should you discover transport damage after unpacking the equipment, inform the hauler immediately. Never connect a damaged device. You may also contact your supplier. DELIVERY PACKET TECHNICAL SPECIFICATIONS Operation temperature Housing Control Protocol Listing Dimensions Weights 0 degC to + 40 degC Black plastic DMX-512 (1990) CE certified 50g Power Requirement 12~24VDC 6A Max *Please Note: Improvements and specifications in the design of the unit and the manual are subject to change without any prior written notice. OPERATION GUIDE 1.DMX Control Mode(DMX Addressing) DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication between intelligent fixtures. Each Dip Switch represents a binary value. In this mode, the dip-switch 10 is flipped to the " " position, DMX address can be addressed and the intensity of LED product is dimmable. ON 1 2 3 4 5 6 7 8 9 10 ON OFF 1 = 0= Connection Terminal Read this manual carefully before using our AcclaimLighting AL-Dimmer-1 PRO. This unit serves as a single channel dimmer. A maximum of up to 6A loads are allowed on a single output, DMX address enables to be addressed by flipping the dip-switch. The dimmer is available in DMX Control Mode, Manual Dim Mode and features 0-10V analog input. The intensity of LED product can be dimmed in the Manual Dim Mode. AL-Dimmer-1 PRO Input 2-pin terminal connector for Power In 2-pin terminal connector for Analog In 3-pin terminal connector for DMX In Output(6A Max.) 3-pin terminal connector for DMX out 4-pin terminal connector for LOAD 90(L) x 40(W) x 20(H)mm User Instructions AL-Dimmer-1 PRO -Page 1- INGRESS PROTECTION RATING IP20

In this mode, the dip-switch 10 is flipped to the " " position, Flip the dip-switch 1~8 to set the intensity of LED product. Each Dip Switch represents a binary value. OFF 1 2 3 4 5 6 7 8 9 10 ON OFF 1 = 0= The intensity is set by combining the different dipswitches that will add up to the value you wish to achieve, for example: Setting the Intensity for 21. Flip switches1,3,&5 to the "ON" position Setting the Intensity for 201. Flip switches1,4,7,& 8 to the "ON" position Dipswitches# Value 1=1 3=4 5=16 =21 Dipswitches# Value 1=1 4=8 7=64 8=128 =201 Dip Switch 1 address equals 1 Dip Switch 2 address equals 2 Dip Switch 3 address equals 4 Dip Switch 4 address equals 8 Dip Switch 5 address equals 16 Dip Switch 6 address equals 32 Dip Switch 7 address equals 64 Dip Switch 8 address equals 128 1,2,4 3,4 1,3,4 2,3,4 1,2,3,4 1 2 1,2 3 1,3 2,3 1,2,3 4 1,4 2,4 SWITCHES ON SWITCHES ON Intensity Value 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 .. .. .. .. .. .. 1 2 3 4 5 6 7 8 9 10 ON OFF 1 = 0= 255 1,2,3,4,5,6,7,8 Intensity Value A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to achieve, for example: Setting DMX address for 201. Flip switches1,4,7,& 8 to the "ON" position Dipswitches# Value 1=1 4=8 7=64 8=128 =201 Setting DMX address for 21. Flip switches1,3,&5 to the "ON" position Dipswitches# Value 1=1 3=4 5=16 =21 Dip Switch 1 address equals 1 Dip Switch 2 address equals 2 Dip Switch 3 address equals 4 Dip Switch 4 address equals 8 Dip Switch 5 address equals 16 Dip Switch 6 address equals 32 Dip Switch 7 address equals 64 Dip Switch 8 address equals 128 Dip Switch 9 address equals 256 1,2,4 3,4 1,3,4 2,3,4 1,2,3,4 1 2 1,2 3 1,3 2,3 1,2,3 4 1,4 2,4 SWITCHES ON SWITCHES ON START CH# START CH# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 .. .. .. .. .. .. 1 2 3 4 5 6 7 8 9 10 ON OFF 1 = 0= 511 1,2,3,4,5,6,7,8,9 .. .. -Page 2-

Analog 0-10V IN Analog 0-10V IN Analog 0-10V IN Analog 0-10V IN Analog 0-10V IN -Page 3-