Morso 1400 Instructions For Installation And Use Manual

A wall sleeve should be bricked securely into the wall of the chimney at the appropriate height and the stovepipe inserted centrally. The pipe must not extend into the actual chimney open- ing, but rather must reach only to the inside of the chimney aperture. The gap between the stovepipe and sleeve must be sealed using glass fibre packing rope. Only use stovepipe components that comply to National and Local Building Regulations. 1.8 Connecting to a stainless steel insulated chimney system If your installation involves taking the chimney straight ...

ing embers in the bed. Spread the embers across the bottom, but concentrated mostly towards the front of the stove. 6. Place three pieces of fuel weighing roughly 0.6 kg and measuring about 25 cm in length across the coals in one layer, with spacing of roughly 1 cm between the pieces of wood. 7. When the secondary air supply (top vent) is opened all the way and the door is closed, the new fuel will ignite in a few minutes. 8. Once the new fuel has taken, adjust the secondary air amount to the desired setting; optimal com ...

the stove (B) Above the stove Clearance to furniture Morsø 1410 uninsulated flue 300 mm 500 mm 600 mm 700 mm Morsø 1410 insulated flue 200 mm 550 mm 600 mm 700 mm Morsø 1440 uninsulated flue 350 mm 300 mm 600 mm 700 mm Morsø 1440 insulated flue 200 mm 250 mm 600 mm 700 mm In situations where the stove is to be fitted into a brick or non-combustible recess, we recommend that the stove is installed with at least 10 cm clearance to the wall, this will allow room air to circulate around the stove; also the maintenance of the outside stove is ea ...

A wall sleeve should be bricked securely into the wall of the chimney at the appropriate height and the stovepipe inserted centrally. The pipe must not extend into the actual chimney open- ing, but rather must reach only to the inside of the chimney aperture. The gap between the stovepipe and sleeve must be sealed using glass fibre packing rope. Only use stovepipe components that comply to National and Local Building Regulations. 1.8 Connecting to a stainless steel insulated chimney system If your installation involves taking the chimney straight ...

The heat output of your stove is regulated by means of the air inlets. The primary air sup- ply, i.e. the air which passes through the shaking grate, is controlled by the bottom draft vent, while the secondary air supply, i.e. the air supplied to the fire across the glass window, is con- trolled by the top draft vent. The stove’s rated heat output is 4.8 kW. The efficiency is 76%. Your new Morsø stove is EN-tested and recommended to be fired with wood. The stove is intended for intermittent use. N.B! Wood is a material that contains a great deal of ga ...

the stove (B) Above the stove Clearance to furniture Morsø 1410 uninsulated flue 300 mm 500 mm 600 mm 700 mm Morsø 1410 insulated flue 200 mm 550 mm 600 mm 700 mm Morsø 1440 uninsulated flue 350 mm 300 mm 600 mm 700 mm Morsø 1440 insulated flue 200 mm 250 mm 600 mm 700 mm In situations where the stove is to be fitted into a brick or non-combustible recess, we recommend that the stove is installed with at least 10 cm clearance to the wall, this will allow room air to circulate around the stove; also the maintenance of the outside stove is ea ...

• Stove being used/fired too vigorously • Too much air passing through the bottom grate • Use of excessively dry wood (wood from old furniture) • Excessive debris collection on baffle plate or inner fireback (see section on cleaning) • Ash level too high in the ash pan (see section on ash Firebricks It should be expected that at sometime the Chamote firebricks will show some signs of crack- ing in its surface; however this is regarding as natural and will not alter the overall function. Gaskets The rope gaskets in the door will need reg ...

the stove (B) Above the stove Clearance to furniture Morsø 1410 uninsulated flue 300 mm 500 mm 600 mm 700 mm Morsø 1410 insulated flue 200 mm 550 mm 600 mm 700 mm Morsø 1440 uninsulated flue 350 mm 300 mm 600 mm 700 mm Morsø 1440 insulated flue 200 mm 250 mm 600 mm 700 mm In situations where the stove is to be fitted into a brick or non-combustible recess, we recommend that the stove is installed with at least 10 cm clearance to the wall, this will allow room air to circulate around the stove; also the maintenance of the outside stove is ea ...