Rangemaster ELAS90EC User's Manual & Installation Instructions

best possible cooking performance and years of faithful service. However, a great cooker alone cannot guarantee perfect results every time. The other vital ingredients are of course enthusiasm and quality cookware. We ofer cookware to work perfectly with all fuel types manufactured by Rangemaster, including induction hobs. You can be assured of functionality with style, as well as the quality and meticulous attention to detail you expect from the pioneers of range cooking. Visit: www.rangemastercookshop.co.uk Ingredients • Oil for greasing • 100 g strawberries • 100 g raspberries • 100 g redcurrants • 100 g blackberries • or a 400 g mixture of any soft fruits • 2 medium eggs • 30 g caster sugar • 80 ml skimmed milk • 2 tsp vanilla extract • 60 g plain four (sifted) • 1 tsp baking powder • Icing sugar to dust Method 1. Preheat the oven to 200 °C (for a conventional oven), 180 oC (for a fan oven) or gas mark 6. 2. Lightly grease a dish 26 cm wide x 4 cm deep. 3. Thickly slice any large strawberries and place them with the other fruits into an ovenproof dish, deep enough so the berries are about 2 deep. 4. Whisk the eggs and caster sugar until pale and fufy. Beat the milk and vanilla extract into the mixture and then fold in the sifted four and baking powder. 5. Pour the cake mix over the fruit and bake on the centre shelf of the oven for 15-20 minutes, or until the mixture is cooked through and golden on the top. 6. Dust with icing sugar and serve immediately with cream or crème fraiche. FRUITY BAKED PUDDING Serves 4–6 Ingredients • 3 kg (6½ lb) skinned and boned loin of pork • 2 x 70 g packs prosciutto • Grated zest of 2 lemons • Bay leaves • Salt and freshly ground black pepper For the sauce: • 1 tablespoons plain four • 4 tablespoons lemon juice • Chicken stock/water Method 1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a fan oven) or gas mark 7. 2. Spread one of the packs of prosciutto over a chopping board; place the pork on top with the outer (fat) part of the pork resting on the prosciutto. 3. Sprinkle the lemon zest onto the inside of the meat and season well. Lay the remaining prosciutto on top of the zest and roll up. 4. Secure the pork with string or silicone bands and thread bay leaves under the string, covering the whole piece of pork. Put the meat on to a trivet over a large roasting tin containing enough water to cover the base. 5. Place into the oven and cook for 30 minutes. Reduce the heat to 180 °C conventional oven/160 °C fan oven/gas 4 and continue roasting for a further 25 minutes per 500 g. Should the prosciutto start becoming too brown, cover with some foil. 6. When the pork is cooked, place onto a warm plate, cover with foil and allow to rest for at least 20 minutes. 7. Spoon of most of the fat from the roasting tin and stir the four into the remaining. Gradually add the stock and lemon juice, adding more stock until the desired consistency is reached and simmer for 5 minutes. Check the seasoning, adding more pepper or lemon juice as necessary. 8. Remove the string or bands from the pork and carve into slices, serve with the sauce. ROAST LOIN OF PORK WITH PROSCUITTO & BAY LEAVES

1 Installation and Maintenance 1 Peculiar Smells 1 Ventilation 1 Personal Safety 1 Hob Care 2 Cooker Care 3 Cleaning 3 2. Cooker Overview 4 The Hob 4 The Grill / Glide-out Grill 6 The Ovens 7 Operating the Ovens 9 The Clock 10 Accessories 14 Main Oven Light 14 3. Cooking Tips 15 Tips on Cooking with the Timer 15 General Oven Tips 15 4. Cooking Table 16 5. Cleaning Your Cooker 17 Hob 17 Grills 18 Control Panel and Doors 18 Ovens 19 The Tall Oven 19 Cleaning Table 20 6. Troubleshooting 21 7. Installation 23 Dear Installer 23 Safety Requirements and Regulations 23 Provision of Ventilation 23 Location of Cooker 23 Positioning the Cooker 24 Moving the Cooker 24 Repositioning the Cooker Following Connection 25 Levelling the Cooker 25 Electrical Connection 26 Final Checks 26 Final Fitting 27 Customer Care 27 8. Circuit Diagrams 28 Circuit Diagram: Hob 28 Circuit Diagram: Fan Oven 29 Circuit Diagram: Multi-function Oven (Classic Deluxe) 30 Circuit Diagram: Multi-function Oven (Elan) 31 9. Technical Data 32 Contents 90 Ceramic U110016-03A

This User Guide covers a number of diferent models. Although some of the illustrations will look diferent to your particular model the functions will be the same. We hope the meaning is clear. Your cooker should give you many years of trouble-free cooking if installed and operated correctly. It is important that you read this section before you start, particularly if you have not used a ceramic cooker before. n n This appliance is designed for domestic cooking only. Using it for any other purpose could invalidate any warranty or liability claim. In particular, the oven should NOT be used for heating the kitchen – besides invalidating claims, this wastes fuel and may overheat the control knobs. Installation and Maintenance In the UK the electrical installation should be in accordance with BS 7671. Otherwise, all installations must be in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local electricity supply companies’ requirements. Make sure that the cooker is wired in and switched on. Set the clock to make sure that all the ovens are functional – see the relevant section in this manual. The cooker should be serviced only by a qualifed service engineer, and only approved spare parts should be used. Always allow the cooker to cool and then switch it of at the mains before cleaning or carrying out any maintenance work, unless specifed otherwise in this guide. Peculiar Smells When you frst use your cooker it may give of an odour. This should stop after use. Before using your cooker for the frst time, make sure that all packing materials have been removed and then, to dispel manufacturing odours, turn the ovens to 200 °C and run for at least an hour. Before using the grill for the frst time you should also turn on the grill and run for 30 minutes with the grill pan in position, pushed fully back, and the grill door open. Make sure the room is well ventilated to the outside air (see ‘Ventilation’ below). People with respiratory or allergy problems should vacate the area for this brief period. Ventilation The use of a cooking appliance results in the production of heat and moisture in the room in which it is installed. Therefore, make sure that the kitchen is well ventilated: keep natural ventilation holes open or install a powered cookerhood that vents outside. If you have several hotplates on, or use the cooker for a long time, open a window or turn on an extractor fan. Personal Safety n n DO NOT modify this appliance. n n This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. n n Children or infrm persons should be supervised to make sure that they do not play with the appliance. n n CAUTION: A long term cooking process has to be supervised from time to time. A short term cooking process has to be supervised continuously. n n Danger of fre: DO NOT store items on the cooking surfaces. n n To avoid overheating, DO NOT install the cooker behind a decorative door. n n Accessible parts will become hot during use and will retain heat even after you have stopped cooking. Keep babies and children away from the cooker and never wear loose–ftting or hanging clothes while the appliance is in use. n n DO NOT use a steam cleaner to clean the cooker. Always be certain that the controls are in the OFF position when the oven is not in use, and before attempting to clean the cooker. n n Take care when touching the marked cooking areas of the hob. n n When the oven is on, DO NOT leave the oven door open for longer than necessary – otherwise the control knobs may become very hot. Always keep combustible materials, e.g. curtains, and fammable liquids a safe distance away from your cooker. n n DO NOT spray aerosols in the vicinity of the cooker while it is on. Use dry oven gloves when applicable – using damp gloves might result in steam burns when you touch a hot surface. Do not use a towel or other bulky cloth in place of a glove – it might catch fre if brought into contact with a hot surface. n n NEVER operate the cooker with wet hands. n n DO NOT use aluminium foil to cover shelves, linings or the oven roof. n n NEVER heat unopened food containers. Pressure build up may make the containers burst and cause injury. n n DO NOT use unstable saucepans. Always make sure that you position the handles away from the edge of the hotplate.

ArtNo.312-0001 Not cooking surface Fig.1-1 n n Make sure to use adequately sized pans with fat bottoms that are large enough to cover the surface of the hotplate heating area. Using undersized pans will expose a portion of the hotplate surface to direct contact and may result in the ignition of clothing. Never leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy spills may catch on fre. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point. n n WARNING! Unattended cooking on a hob with fat or oil can be dangerous and may result in fre. n n NEVER leave a chip pan unattended. Always heat fat slowly, and watch as it heats. Deep fry pans should be only one third full of fat. Filling the pan too full of fat can cause spill over when food is added. If you use a combination of oils or fats in frying, stir them together before heating, or as the fats melt. Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan. Carefully watch for spills or overheating of foods when frying at high or medium high temperatures. Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool. Do not use the top of the fue (the slot along the back of the cooker) for warming plates, dishes, drying tea towels or softening butter. n n DO NOT use water on grease fres and never pick up a faming pan. Turn of the controls and then smother a faming pan on a surface unit by covering the pan completely with a well-ftting lid or baking tray. If available, use a multi-purpose dry chemical or foam-type fre extinguisher. Cooking high moisture content foods can create a ‘steam burst’ when the oven door is opened. When opening the oven stand well back and allow any steam to disperse (Fig.1-1). Take care that no water seeps into the appliance. Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for hotplate cooking; others may break because of the sudden change in temperature. This appliance is heavy so take care when moving it. Hob Care n n NEVER cook directly on the hob surface (Fig.1-2). n n DO NOT use the hob surface as a cutting board. Do not leave utensils, foodstufs or combustible items on the hob when it is not is use (e.g. tea towels, frying pans containing oil). n n DO NOT place plastic or aluminium foil, or plastic containers, on the hob. n n DO NOT leave the hob zones switched on unless being used for cooking. ArtNo.312-0002 Salt cellar onto hob Fig.1-2 ArtNo.312-0003 Moving pans Fig.1-3 Fig.1-4

oven steam out the back n n NEVER allow anyone to climb or stand on the hob. Do not stand or rest heavy objects on the hob. Although the ceramic surface is very strong, a sharp blow or sharp falling object (e.g. a salt cellar) might cause the surface to crack or break (Fig.1-3). n n Should a crack appear in the surface, disconnect the appliance immediately from the supply and arrange for its repair. Always LIFT pans of the hob. Sliding pans may cause marks and scratches (Fig.1-4). Always turn the control to the OFF position before removing a pan. n n Take care when placing hot lids onto the hob surface. Lids that have been covering boiling or steaming foods can ‘stick’ to the ceramic glass. Should this occur, DO NOT attempt to lift the lid of the hotplate: this may damage the hob surface. Instead, slide the lid to the edge of the hob surface and remove. DO NOT place anything between the base of the pan and the hob surface (e.g. asbestos mats, aluminium foil, wok stand). n n Avoid heating an empty pan. Doing so may damage both the hob and pan. Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for hob cooking; others may break because of the sudden change in temperature. The ceramic surface should be washed after use in order to prevent it from becoming scratched or dirty. However, you should clean the hob with caution as some cleaners can produce noxious fumes if applied to a hot surface. DO NOT use abrasive cleaners/pads, oven aerosols/pads or stain removers on the surface. We recommend that you avoid wiping any surface unit areas until they have cooled and the indicator light has gone of. Sugar spills are the exception to this (see ‘Cleaning your Cooker’). After cleaning, use a dry cloth or paper towel to remove any cleaning cream residue. Cooker Care As steam can condense to water droplets on the cool outer trim of the oven, it may be necessary during cooking to wipe away any moisture with a soft cloth. This will also help to prevent soiling and discolouration of the oven exterior by cooking vapours (Fig.1-5). Cleaning In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other food stuf could result in a fre. Clean only the parts listed in this guide. Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface. Fig.1-5

The 90 ceramic cooker (Fig.2-1) has the following features: A. A ceramic hob B. A control panel C. A separate grill or glide-out grill D. A programmable fan oven or multi-function oven (depending on model) E. A tall fan oven The Hob Use only pans that are suitable for ceramic hobs. We recommend stainless steel and enamelled steel pans as pots and pans with copper or aluminium bases leave traces on the hob that are difcult to remove. The kind of pan you use and the quantity of food afects the setting required. Higher settings are required for larger quantities of food. Pots and pans should have thick, smooth, fat bottoms (Fig.2-2). This allows the maximum heat transfer from the hob to the pan, making cooking quick and energy efcient. Never use a round-bottomed wok, even with a stand. The very best pans have bases that are very slightly curved up when cold. If you hold a ruler across the bottom you will see a small gap in the middle (Fig.2-3). When they heat up the metal expands and lies fat on the cooking surface. Fig.2-2 ArtNo.200-0001 - 90 Induction annotated GENERIC 1 4 6 5 3 2 1 4 6 5 3 2 1 4 6 5 3 2 1 1 3 4 4 3 2 2 1 1 3 4 4 3 2 2 A B C D E Fig.2-1 Fig.2-3 DocNo.020-0002 - Overview - 90 Ceramic - Generic

1.65 kW 1.1 kW 2.02 kW 1.1 kW 1.56 kW ArtNo.312-0013 - 90 ceramic heat indicator light ArtNo.312-0003 Moving pans Make sure that the base of the pan is clean and dry to prevent any residue burning onto the hob panel. This also helps prevent scratches and deposits. Always use pans that are the same size as (or slightly larger than) the areas marked on the hob top (Fig.2-4). Using smaller pans wastes heat, and any spillage will be burnt on. Using a lid will help the contents boil more quickly. Always lift pans of the hob (Fig.2-5). Sliding pans may cause marks and scratches. Always turn the control to the ‘OFF’ position before removing a pan. n n Take care when placing hot lids onto the hob surface. Lids that have been covering boiling or steaming foods can ‘stick’ to the ceramic glass. Should this occur, DO NOT attempt to lift the lid of the hotplate: this may damage the hob surface. Instead, slide the lid to the edge of the hob surface and remove. There are indicator lights for each of the cooking areas (Fig.2-6). The lights come on when a hob control is turned on and stays lit while the surface cools. n n Always take care before touching the surface, even when the hob is turned of – it may be hotter than you think. The ratings of the diferent cooking areas are shown in (Fig.2-7). The areas marked with two concentric circles have an inner and an outer element. Rotate the control knob clockwise to heat the whole area for larger pans; turn it counter-clockwise to just heat the inner part for smaller pans (Fig.2-8). When cooking on the hob, you may see the hob area you are using switch of and on: this is caused by a safety device that limits the temperature of the hob. This is quite normal, especially when cooking at high temperatures. If it happens a lot with a particular pan, however, it may mean the pan is not suitable – perhaps too small or too uneven – for a ceramic hob. For best results, preheat a covered serving dish for 10 minutes before adding food to it. Use only heat-resistant dishes. Fig.2-5 ArtNo.312-0006 Correct pan sizes Fig.2-4 Fig.2-7 Fig.2-6 1 2 3 1 2 3 Fig.2-8

Fig.2-12 ArtNo.330-0003 - Grill pan w handle pulled forwards ArtNo.200-0003 - Generic grill control to full Fig.2-9 Fig.2-11 ArtNo.331-0001Grill pan pulled forwards Fig.2-10 The Grill / Glide-out Grill Open the door and pull the grill pan (Fig.2-9) or carriage (Fig.2-10) forward using the handle. The grill has two elements that allow either the whole area of the pan to be heated or just the right-and half. Adjust the heat to suit by turning the knob. To heat the whole grill, turn the knob clockwise (Fig.2-11). To heat the right-hand half, turn the knob counter-clockwise. The neon indicator light by the grill control will come on. For best results, leave the grill pan in the grill chamber and preheat the appropriate part(s) of the grill for two minutes. The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat. n n DO NOT leave the grill on for more than a few moments, without the grill pan underneath it, otherwise the knobs may become hot. Once the grill has preheated, take the grill pan out again and put the trivet back in place with the food on it. Slide the grill pan or carriage back into the grill chamber. Make sure that it is pushed right in. n n Accessible parts may be hot when the grill is in use. Young children should be kept away. The grill pan trivet can be turned over to give two grilling positions (Fig.2-12). n n Never close the grill door when the grill is on.

Fig.2-13 Function Use Defrost To thaw small items in the oven without heat Fan oven A full cooking function, even heat throughout, great for baking Fanned grilling Grilling meat and fish with the door closed Fan assisted A full cooking function good for roasting and baking Conventional oven A full cooking function for roasting and baking in the lower half of the oven Browning element To brown and crisp cheese topped dishes Base heat To crisp up the bases of quiche, pizza or pastry ArtNo.321-0006 - Multi-function oven Fig.2-14 ArtNo.323-0002 Tall oven Fig.2-15 Fan oven Multi-function oven Tall fan oven Table 2-1 The Ovens The clock must be set to the time of day before the ovens will work. See the following section on ‘The Clock’ for instructions on setting the time of day. References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed from the front of the appliance. The left-hand oven is either a fan oven (Fig.2-13) or a multi-function oven (Fig.2-14), depending on model. The right-hand tall oven is a fan oven (Fig.2-15). Fan ovens circulate hot air continuously, which means faster, more even cooking. The recommended cooking temperatures for a fan oven are generally lower than those for a non-fan oven. Multi-function ovens have an oven fan and oven fan element, as well as two extra heating elements. One element is in the top of the oven and the second is under the oven base. Take care to avoid touching the top element and element defector when placing or removing items from the oven. The multi-function oven has 3 main cooking functions: fan, fan assisted and conventional cooking. These functions should be used to complete most of your cooking. The browning element and base heat can be used in the latter part of the cooking process to fne tune the results to your particular requirements. Use fanned grilling for all your grilling needs and defrost to safely thaw small items of frozen food. Table 2-1 gives a summary of the multi-function modes. The multi-function oven has many varied uses. We suggest you keep a careful eye on your cooking until you are familiar with each function. Remember, not all functions will be suitable for all food types.

Rapid Response (Classic Deluxe only) The Rapid Response setting enables you to preheat the oven faster than normal. It uses the fan oven element with additional heat from one of the elements in the top of the oven. Fan ovens heat up quickly; but the Rapid Response feature speeds this process up enabling you to start cooking sooner. To use the Rapid Response feature, turn the function control knob to R and set the temperature required. The light on the control panel next to the function control will come on. When the required temperature is reached the top element will switch of and the light will go out. The oven temperature is then maintained by the fan oven element and fan. Should you choose to place food into the cold oven prior to cooking while using the Rapid Response function, make sure that cakes, etc. are not positioned too near the top of the oven. Fan Oven This function operates the fan and the heating element around it. An even heat is produced throughout the oven, allowing you to cook large amounts quickly. Fan oven cooking is particularly suitable for baking on several shelves at one time and is a good ‘all-round’ function. It may be necessary to reduce the temperature by approximately 10 °C for recipes previously cooked in a conventional oven. If you wish to preheat the oven, wait until the indicator light has gone out before inserting the food. Fanned Grilling This function operates the fan whilst the top element is on. It produces a more even, less ferce heat than a conventional grill. For best results, place the food to be grilled on a trivet over a roasting tin, which should be smaller than a conventional grill pan. This allows greater air circulation. Thick pieces of meat or fsh are ideal for grilling in this way, as the circulated air reduces the ferceness of the heat from the grill. The oven door should be kept closed while grilling is in progress, so saving energy. You will also fnd that the food needs to be watched and turned less than for normal grilling. Preheat this function before cooking. Fan Assisted Oven This function operates the fan, circulating air heated by the elements at the top and the base of the oven. The combination of fan and conventional cooking (top and base heat) makes this function ideal for cooking large items that need thorough cooking, such as a large meat roast. It is also possible to bake on two shelves at one time, although they will need to be swapped over during the cooking time, as the heat at the top of the oven is greater than at the base, when using this function. This is a fast intensive form of cooking; keep an eye on the food cooking until you have become accustomed to this function. Conventional Oven (Top and Base Heat) This function combines the heat from the top and base elements. It is particularly suitable for roasting and baking pastry, cakes and biscuits. Food cooked on the top shelf will brown and crisp faster than on the lower shelf, because the heat is greater at the top of the oven than at the base, as in ‘Fan assisted oven’ function. Similar items being cooked will need to be swapped around for even cooking. This means that foods requiring diferent temperatures can be cooked together, using the cooler zone in the lower half of the oven and hotter area to the top. The exposed top element may cook some foods too quickly, so we recommend that the food be positioned in the lower half of the oven to cook. The oven temperature may also need to be lowered. Browning Element This function uses the element in the top of the oven only. It is a useful function for the browning or fnishing of pasta dishes, vegetables in sauce, shepherds pie and lasagne, the item to be browned being already hot before switching to the top element. Base Heat This function uses the base element only. It will crisp up your pizza or quiche base or fnish of cooking the base of a pastry case on a lower shelf. It is also a gentle heat, good for slow cooking of casseroles in the middle of the oven or for plate warming. The Browning and Base Heat functions are useful additions to your oven, giving you fexibility to fnish of items to perfection. Defrost This function operates the fan to circulate cold air only. No heat is applied. This enables small items such as desserts, cream cakes and pieces of meat, fsh and poultry to be defrosted. Defrosting in this way speeds up the process and protects the food from fies. Pieces of meat, fsh and poultry should be placed on a shelf, over a tray to catch any drips. Be sure to wash the shelf and tray after defrosting. Defrost with the oven door closed. Large items, such as whole chickens and joints should not be defrosted in this way. We recommend this be carried out in a refrigerator. Defrosting should not be carried out in a warm oven or when an adjoining oven is in use or still warm. Make sure that dairy foods, meat and poultry are completely defrosted before cooking.

Fan Ovens Turn the oven knob to the desired temperature (Fig.2-16). The oven indicator light will glow until the oven has reached the temperature selected. It will then cycle on and of during cooking. Multi-function Ovens The multi-function oven has two controls: a function selector and a temperature setting knob (Fig.2-17). Turn the function selector control to a cooking function. Turn the oven temperature knob to the temperature required (Fig.2-16). The oven heating light will glow until the oven has reached the temperature you selected. It will then cycle on and of during cooking. Fig.2-16 Temperature control Function control Fig.2-17

A B A – Timer knob, B – Adjusting knob Fig.2-18 ArtNo.300-0005 2BC minute minder setting ArtNo.300-0006 2BC minute minder setting 2 ArtNo.301-0007 2BC Stopping the oven 1 ArtNo.301-0008 2BC Stopping the oven 2 Fig.2-19 Fig.2-20 Fig.2-21 Fig.2-22 ArtNo.301-0009 2BC Setting the cooking timer ArtNo.301-0010 2BC Setting the cooking time Fig.2-23 Fig.2-24 The Clock You can use the clock to turn the left-hand oven on and of. The clock must be set to the time of day before the oven will work. Note on multi-function ovens: When using the timer functions, frst set the clock as required before setting the oven temperature and selecting the oven function. The 2-button Clock Setting the time of day The 2-button LCD clock is shown in (Fig.2-18). When the clock is frst connected, the display fashes ( 0.00 ) and (G) alternately. To set the time, turn and hold the Timer knob to the clock symbol [A] and at the same time turn the Adjusting knob left or right until the clock shows the time of day. Remember this is a 24-hour clock. Let go of the Timer knob and it will spring back to the vertical, oven manual setting. IMPORTANT: The left-hand oven will not operate unless the clock has been set. Setting the minute minder To activate the minute minder turn the Timer knob to the right to the [C] minute minder setting – it should click into position (Fig.2-19). Rotate the Adjusting knob to set the time required (Fig.2-20). You can either turn the knob back to the vertical manual setting [B] to keep an eye on the time of day, or leave it in the [C] minute minder position as the time ticks down. To stop the beeper when it sounds, turn the Adjusting knob counter-clockwise. • The ‘cook period’, which is the length of time you want the oven to cook for. • The ‘stop time’, which is the time of day you want the oven to stop cooking. To stop the oven at a specifc time of day Turn the Timer knob to the [E] position (Fig.2-21). Use the Adjusting knob to set the ‘stop time’. You can set the oven to turn on at any time over the following 24-hour period. AUTO shows in the display (Fig.2-22). Turn the Timer knob to the bottom ‘AUTO’ setting to return to the clock display. Once the ‘stop time’ is reached, the beeper sounds. Turn the Timer knob to the vertical [B] to return to manual cooking. To start and then stop the oven using the Timer You cannot set a start time directly – this is set automatically by a combination of the ‘cook time’ and ‘stop time’. Turn the Timer knob to the [D] position (Fig.2-23). Turn the Adjusting knob to set the ‘cooking time’ you need (Fig.2-24).

show the current time of day plus the ‘cook time’ you just set. Use the Adjusting knob to set the ‘stop time’ required (Fig.2-25). The ‘stop time’ is displayed, followed by ‘AUTO’. Set the oven to the cooking temperature you need. Turn the Timer knob to the ‘Auto’ setting. When your cooking is fnished, the beeper sounds. Turn the Timer knob to the vertical [B] to return to manual cooking. If you are out, do not worry about the beeper going of – it stops on its own after a while. When you return, turn the Timer knob to the vertical [B] to return to manual cooking. AUTO is showing, but you want to revert to manual cooking You can cancel any automatic settings by briefy turning the Timer knob to the clock symbol [A] and then releasing it. Key Lock When the key lock is activated the left-hand oven is locked and will not come on. The right-hand oven can be operated as usual. To activate the key lock Make sure that the clock is in manual mode and cancel any active programs. Turn and hold the Timer knob to the clock symbol [A] for about 8 seconds. ‘On’ appears on the display (Fig.2-26). While still holding the Timer knob turned to the clock symbol [A], turn the Adjusting knob clockwise until the key symbol [F] and ‘OF’ shows on the display (Fig.2-27). Release the knobs. The left-hand oven is now locked, as is confrmed by the display showing the time of day alongside the key symbol [F] (Fig.2-28). To turn of the key lock Turn and hold the Timer knob to the clock symbol [A] for about 8 seconds. ‘OF’ will appear on the display (Fig.2-29). While still holding the Timer knob turned to the clock symbol [A], turn the Adjusting knob clockwise until the key symbol [F] goes out on the display and ‘On’ shows (Fig.2-30). Let go of the knobs. After a few seconds, the display reverts to showing the time of day. The oven can now be used normally. ArtNo.301-0008 2BC Stopping the oven 2 Fig.2-25 Art No. 301-0011 2BC Activating the key lock 1 ArtNo.301-0012 2BC Activating the key lock 2 ArtNo.301-0013 2BC Activating the key lock 3 ArtNo.301-0014 2BC Deactivating the key lock 1 ArtNo.301-0015 2BC Deactivating the key lock 2 Fig.2-26 Fig.2-27 Fig.2-28 Fig.2-29 Fig.2-30

Setting the time of day The 6-button LCD clock is shown in Fig.2-31. When the clock is frst connected the display fashes ( 0.00 ) and (G) alternately. Press and hold both the [C] and [D] buttons down (Fig.2-32). Now press the [+] button (or the [–] button) until the correct time shows. Do not forget that it is a 24-hour clock. If you need to reset the cooker, turn of the power supply and wait for a couple of minutes and start again. Setting the minute minder Press and hold the [C] button (Fig.2-33), and then press the [+] button until the length of time you want to cook for is shown (Fig.2-34). You can check the time remaining by pressing [C]. When the beeper sounds cancel it by pressing [C]. • The ‘cook period’, which is the length of time you want the oven to cook for. • The ‘stop time’, which is the time of day you want the oven to stop cooking. To stop the oven automatically Press and hold the Stop Time [E] button (Fig.2-35) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig.2-36). AUTO will show in the display. Once the ‘stop time’ is reached, the beeper sounds. To stop the beep turn the oven control knob to 0 frst and then press [B] once; press [B] again to return to manual cooking. To start and stop the oven automatically Before you set the clock you must have two numbers clearly in mind – the ‘cook period’ and the ‘stop time’. Note: You cannot set a start time directly – this is set automatically by setting the ‘cook period’ and the ‘stop time’. Press and hold the [D] button (Fig.2-37) and then press the [+] button (or [–] button) until the required ‘cook period’ shows (Fig.2-38). Now press and hold the [E] button (Fig.2-39) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig.2-40). Release the buttons. AUTO will now show in the display. Set the oven to the required temperature. When cooking is fnished the beeper will sound. Turn the oven knob to the OFF position frst, and then press the [B] button once to stop the beep; press it again to return to manual cooking. If you are out, do not worry about the beeper going of, it stops after a while. When you return, turn the oven knob to 0 frst, and then press [B] twice to return to manual cooking. ArtNo.302-0001 - 6-button clock ArtNo.302-0003 - 6BC minute minder setting 1 ArtNo.302-0004 - Minute minder setting 2 ArtNo.302-0005 - 6BC Stopping the oven 1 Fig.2-32 Fig.2-33 Fig.2-34 Fig.2-35 ArtNo.302-0002 - 6BC annotated A B C D E F Fig.2-31 A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time, D – Manual, E & F – Time setting buttons ArtNo.302-0005a - 6BC Stopping the oven 1a Fig.2-36 ArtNo.302-0006 - 6BC setting the cook time Fig.2-37 ArtNo.302-0006 - 6BC setting the cook time Fig.2-38 ArtNo.302-0005 - 6BC Stopping the oven 1 Fig.2-39 ArtNo.302-0005a - 6BC Stopping the oven 1a Fig.2-40

ArtNo.302-0008 - Activating the key lock 1 ArtNo.302-0009 - Activating the key lock 2 Fig.2-41 Fig.2-42 ArtNo.302-0011 - 6BC Deactivating the key lock 1 Fig.2-43 Fig.2-44 ArtNo.302-0012 - Deactivating the key lock 2 Fig.2-45 AUTO is showing, you want to reset to manual cooking To return to manual cooking from any automatic setting, the ‘cook period’ must be cancelled. Press and hold the [E] button and then press the [–] button until the display reads ( 0.00 ). Press the [B] button to return to manual cooking. Key Lock Activating the key lock will lock the left-hand oven and it will not come on. The right-hand oven can be operated as usual. To activate the key lock Make sure that the clock is in manual mode and cancel any active programs. Hold the Minute Minder [C] and Cook period [D] buttons. When ‘On’ appears on the display (Fig.2-41) press the [+] button once. The key symbol [F] and ‘OF’ will now show on the display (Fig.2-42). Release the buttons. The left-hand oven is now locked, as confrmed by the display showing the time of day alongside the key symbol (Fig.2-43). To turn of the key lock Hold the Minute Minder [C] and Cook period [D] buttons. When ‘OF’ appears on the display (Fig.2-44) press the [+] button once. The key symbol [F] will go out and ‘On’ will show on the display (Fig.2-45). Release the buttons. After a few seconds the display will revert to show the time of day. The oven can now be used normally.

In addition to the fat shelves, some models are supplied with a drop shelf (Fig.2-46). The drop shelf increases the possibilities for oven shelf spacing. The oven shelves can be easily removed and reftted. Pull the shelf forward until the back of the shelf is stopped by the shelf stop bumps in the oven sides (Fig.2-47). Lift up the front of the shelf so the back of the shelf will pass under the shelf stop and then pull the shelf forward (Fig.2-48). To reft the shelf, line up the shelf with a groove in the oven side and push the shelf back until the ends hit the shelf stop. Lift up the front so the shelf ends clear the shelf stops, and then lower the front so that the shelf is level and push it fully back (Fig.2-49). Oven shelves – Right-hand (Tall) Oven The tall oven is supplied with four fat cooking shelves (Fig.2-50) and a plate warming shelf (Fig.2-51). When using the tall oven, you can cook on all four shelves at the same time, but make sure that they are well spaced out allow the hot air to circulate. The Handyrack (Main Oven) The Handyrack (Fig.2-52) fts to the left-hand oven door only. Food cooking on it is easy to attend to, because it is accessible when the door is open. The maximum weight that can be held by the Handyrack is 5.5 kg (12 lb). It should only be used with the supplied roasting tin, which is designed to ft the Handyrack. Any other vessel could be unstable. It can be ftted at two diferent heights. One of the oven shelves must be removed and the other positioned to suit. When the Handyrack is used in its highest position, other dishes can be cooked on the bottom shelf position or base of the oven. When the Handyrack is used in its lowest position, other dishes can be cooked on the second shelf position or base of the oven. To ft the Handyrack, locate one side of it on the door bracket (Fig.2-53). Then spring the other side out to clip it onto the other bracket (Fig.2-54). Main Oven Light Press the button to turn the light on (Fig.2-55). If the oven light fails, turn of the power supply before changing the bulb. See the ‘Troubleshooting’ section for details on how to change the bulb. ArtNo.320-0017 Main oven light Fig.2-55 ArtNo.320-0013 Removing the shelf 3 ArtNo.320-0014 Handyrack on LH door ArtNo.320-0015 Fitting the Handyack 1 Fig.2-52 Fig.2-53 ArtNo.320-0016 Fitting the handyrack 2 Fig.2-54 ArtNo.320-0011 Removing the shelf 1 ArtNo.320-0012 Removing the shelf 2 Fig.2-47 Fig.2-48 Fig.2-49 ArtNo.324-0009 Tall oven shelf ArtNo.324-0010 Plate warming shelf Fig.2-50 Fig.2-51 Shelf guard Front Front Shelf guard Flat shelf Drop shelf Fig.2-46

If you want to cook more than one dish, choose dishes that require approximately the same cooking time. However, dishes can be ‘slowed down’ slightly by using small containers and covering them with aluminium foil, or ‘speeded up’ slightly by cooking smaller quantities or placing them in larger containers. Very perishable foods such as pork or fsh should be avoided if a long delay period is planned, especially in hot weather. n n DO NOT place warm food in the oven to be timed. n n DO NOT use a timed oven that is already warm. n n DO NOT use the timed oven if the adjoining oven is already warm. Whole poultry must be thoroughly defrosted before being placed in the oven. Check that meat and poultry are fully cooked before serving. General Oven Tips The wire shelves should always be pushed frmly to the back of the oven. Baking trays with food cooking on them should be placed level with the front edge of the oven’s wire shelves. Other containers should be placed centrally. Keep all trays and containers away from the back of the oven, as overbrowning of the food may occur. For even browning, the maximum recommended size of a baking tray is 340 mm (13 ½”) by 340 mm (13 ½”) in the main oven and 232 mm (9 1/8”) and 321 mm (12 5/8”) in the tall oven. When the oven is on, do not leave the door open for longer than necessary, otherwise the knobs may get very hot. • Always leave a “finger’s width” between dishes on the same shelf. This allows the heat to circulate freely around them. • To reduce fat splashing when you add vegetables to hot fat around a roast, dry them thoroughly or brush lightly with cooking oil. • Where dishes may boil and spill over during cooking, place them on a baking tray. • The ‘Cook & Clean’ oven liners (see ‘Cleaning Your Cooker’) work better when fat splashes are avoided. Cover meat when cooking with foil or use a roasting bag. • Sufficient heat rises out of the oven while cooking to warm plates in the grill compartment. • If you want to brown the base of a pastry dish, preheat the baking tray for 15 minutes before placing the dish in the centre of the tray. 3. Cooking Tips DocNo.030-0006 - Cooking tips - 90 electric

ArtNo.050-0007 Oven shelf positions Oven Shelf Positions Top Centre Base The oven control settings and cooking times given in the table below are intended to be used AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a preferred result. Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The temperature in the fan oven does not vary with height in the oven so you can use any shelf. Food Meat Beef (no bone) Lamb Pork Poultry Chicken Turkey Duck Casserole Yorkshire Pudding Cake Very rich fruit - Christmas, wedding, etc. Fruit 180 mm tin Fruit 230 mm tin Madeira 180 mm Queen cakes Scones Victoria sandwich 180 mm tin 210 mm tin Desserts Shortcrust tarts Fruit pies Tartlets Puff pastry Meringues Baked egg custard Baked sponge pudding Milk pudding Bread Fish Fillet Whole Steak Approximate Cooking Time 30-35 minutes per 500g +30-35 minutes. 20-25 minutes per 500g +20-25 minutes. 30-35 minutes per 500g +30-35 minutes. 25-30 minutes per 500g +25-30 minutes. 35-40 minutes per 500g +35-40 minutes. 25-30 minutes per 500g +25-30 minutes. 20-25 minutes per 500g +20-25 minutes. 15-20 minutes per 500g +15-20 minutes. 20 minutes per 500g +20 minutes. 15 minutes per 500g +15 minutes. 25-30 minutes per 500g. 20 minutes per 500g. 2-4 hours according to recipe. Large tins 30-35 minutes; individual 10-20 minutes. 45-50 minutes per 500g of mixture. 2-2½ hours. Up to 3½ hours. 80-90 minutes. 15-25 minutes. 10-15 minutes. 20-30 minutes. 30-40 minutes. 20-30 minutes on a preheated tray. 35-45 minutes. 10-20 minutes according to size. 20-40 minutes according to size. 2-3 hours. 45-60 minutes. 40-45 minutes. 2 to 3 hours. 20-30 minutes. 15-20 minutes. 15-20 minutes per 500g. Steaks according to thickness. Conventional Oven Temperature °C (Shelf Position) 160 (C) 200 (C) 160 (C) 200 (C) 160 (C) 200 (C) 160 (C) 200 (C) 160 (C) 200 (C) 160 (C) 200 (C) 140-150 (C) 220 (C) 140 (C/B) 150 (C/B) 150 (C/B) 160 (C/B) 190 (C/B) 220 (C/B) 180 (C/B) 180 (C/B) 200 (C/B) 200 (C/B) 200 (C/B) 210 (C/B) 100 (C/B) 160 (C/B) 180 (C/B) 140-150 (C/B) 210 (C) Fanned Grilling 190 (C/B) 190 (C/B) 190 (C/B) Fan Oven Temperature °C 150 190 150 190 150 190 150 190 150 190 150 190 130-140 210 130 140 140 150 180 210 170 170 190 190 190 200 90 150 170 130-140 200 190 (C/B) 190 (C/B) 190 (C/B) Thoroughly thaw frozen joints before cooking. Meat may be roasted at 220°C (210°C for fan oven) and the cooking time adjusted accordingly. For stuffed and rolled meats, add approximately 10 minutes per 500g, or cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for the remainder. For stuffed poultry, you could cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for remainder. Do not forget to include the weight of the stuffing. For fresh or frozen prepacked poultry, follow instructions on the pack. Thoroughly thaw frozen poultry before cooking. Using the conventional oven: when two tier cooking leave at least one runner space between shelves. Position the baking tray with the front edge along the front of the oven shelf. ArtNo.050-0001 Gas cooking table Using the conventional oven: for even browning the maximum size of baking tray recommended is 340 mm x 340 mm. This ensures free heat circulation. If cooking a two tier load, the trays should be interchanged approximately halfway though the cooking time. Up to three tiers can be cooked in a fan oven at the same time but make sure to leave at least one runner space between each shelf being cooked on. DocNo.031-0004 - Cooking table - electric & fan single cavity

Isolate the electricity supply before carrying out any major cleaning. Allow the cooker to cool. n n NEVER use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt. n n DO NOT mix diferent cleaning products – they may react together with hazardous results. All parts of the cooker can be cleaned with hot soapy water – but take care that no surplus water seeps into the appliance. Remember to switch the electricity supply back on and reset the clock before reusing the cooker. Hob Daily Care First of all make sure that all heat indicator lights are of and that the cooking surface is cool. Apply a small dab of ceramic cleaning cream in the centre of each area to be cleaned. Dampen a clean paper towel and work the cream onto the cooking surface. As a fnal step, wipe the cooking surface with a clean, dry paper towel. Cleaning Spills For spills and boil-overs that occur while cooking, turn the unit of and wipe the area surrounding the hot zone with a clean paper towel. If a spill (other than a sugary substance) is on the hot zone, do not clean until the unit has completely cooled down, and then follow the instructions below (‘Cleaning burned-on spills’). If you accidentally melt anything on the surface, or if you spill foods with a high sugar content (preserves, tomato sauce, fruit juice, etc.), remove the spill IMMEDIATELY with a razor scraper, while the unit is still hot. IMPORTANT: Use an oven glove to protect your hand from potential burns. Scrape the major spill or melted material from the cooking zone and push into a cold area. Then, turn the unit ‘OFF’ and allow it to cool before cleaning further. After the cooking surface cools down and the heat indicator lights go of, follow the ‘Daily Care’ procedure outlined above. Cleaning Burned-on Spills Make sure that the heat indicator lights are of and that the hob is cool. Remove the excess burned-on substance with a single-edged razor scraper. Hold the scraper at an angle of about 30° to the surface and then scrape of the burned-on matter (Fig.5-1). Once you have removed as much as possible with the scraper, follow the ‘Daily Care’ procedure outlined above. ArtNo.312-0010 Cleaning; scraping the ceramic hob Fig.5-1 DocNo.042-0003 - Cleaning - CE 90 - GENERIC

Fig.5-2 ArtNo.331-0003 Grill frame out, no pan ArtNo.331-0004 Removing the grill frame Fig.5-3 Fig.5-4 ArtNo.331-0005 Removing the grill rail Fig.5-5 ArtNo.331-0006 Grill pan plan Fig.5-6 Grills The grill pan and trivet should be washed in hot soapy water. After grilling meats or any foods that soil, leave to soak for a few minutes immediately after use. Stubborn particles may be removed from the trivet using a nylon brush. Alternatively, the grill pan can be washed in a dishwasher. n n Before you remove any of the grill parts for cleaning, make sure that they are cool, or use oven gloves. n n DO NOT use any abrasive substances. Cleaning the Glide-out Grill The grill pan can be easily removed for cleaning as follows: Remove the grill pan support frame by pulling the grill pan forward (Fig.5-2). Lift the grill pan clear of the support frame. The support frame is held to the side rails by two clips on each side (Fig.5-3). For each side, support the side rail with one hand and with the other hand lift the frame up and out of the side clips (Fig.5-4). For safety, push the side rails back into the grill chamber. If you need to remove the side rails to allow cleaning of the grill chamber, you can unhook them from the grill chamber sides (Fig.5-5) and wipe the sides clean with a soft cloth and mild detergent. n n DO NOT put the side runners in a dishwasher. Once you have fnished, hook the side rails back onto the sides of the chamber. To reft the frame, pull the side rails forward and, for each side in turn, support the side rail and press the frame down into the side rails. Replace the grill pan. When reftting the grill pan, make sure that the wide rim is at the front (Fig.5-6). Control Panel and Doors Avoid using any abrasive cleaners, including cream cleaners. For best results, use a liquid detergent. The same cleaner can also be used on the doors, or alternatively, using a soft cloth wrung out in clean hot soapy water. You can use the same method for cleaning the control panel and knobs. After cleaning, polish with a dry cloth.

The oven door front panels can be taken of so that the glass panels can be cleaned. Move the cooker forward to gain access to the sides (see the ‘Moving the Cooker’ section under ‘Installation’). Open the oven door slightly and remove the front panel fxing screws from the door sides, two each side (Fig.5-7). Carefully lift of the outer door panel. The inside face of the glass panels can now be cleaned – take care not to disturb or wet the door insulation. Note: If the door is triple glazed then the inner two panels are fxed together and should not be separated. After cleaning, carefully reft the outer door panel and replace the side fxing screws. n n DO NOT use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass. Ovens 'Cook & Clean' Panels The main oven has side ‘Cook & Clean’ panels which have been coated with a special enamel that partly cleans itself. This does not stop all marks on the lining, but helps to reduce the amount of manual cleaning needed. These panels work better above 200 °C. If you do most of your cooking below this temperature, occasionally remove the panels and wipe with a lint free cloth and hot soapy water. The panels should then be dried and replaced and the oven heated at 200 °C for about one hour. This will make sure that the panels are working efectively. Removing the Panels to clean the Enamel Interior If you wish to clean the enamel interior of the oven, you will need to remove the shelves, followed by the ‘Cook & Clean’ panels. Each side of the oven is fxed with four fxing screws. You do not have to remove the screws to remove the oven panels. Simply lift each side panel upwards, slide them of the screws and then pull them forwards (Fig.5-8). Once the panels have been removed, the oven enamel interior can be cleaned. DO NOT use steel wool, oven cleaning pads, or any other materials that will scratch the surface. The Tall Oven To clean the oven sides, slide out the shelves, unhook the supports from the oven sides and lift out (Fig.5-9). ArtNo.320-0002a Proplus oven door side screws Fig.5-7 ArtNo.320-0008 Removing the oven lining Fig.5-8 ArtNo.320-0022 Tall oven side support Fig.5-9

electrical retailers as stated. For enamelled surfaces use a cleaner that is approved for use on vitreous enamel. Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately. Hotplate Part Finish Recommended Cleaning Method Hob Top Enamel or stainless steel Hot soapy water, soft cloth. Any stubborn stains remove gently with a nylon scourer. Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary. Griddle plate (some models only) Non-stick surface Allow to cool. Wash in hot soapy water. Do not use abrasive cleaners/scourers. Dishwasher. Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary. Outside of cooker Part Finish Recommended Cleaning Method Door, Door surround and storage drawer exterior. Enamel or paint Hot soapy water, soft cloth. Any stubborn stains, remove gently with a liquid detergent. Stainless steel E-cloth (electrical retailers) or microfbre all-purpose cloth (supermarket). Sides and plinth Painted surface Hot soapy water, soft cloth. Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary. Control panel Paint, enamel or stainless steel Warm soapy water. Do not use abrasive cleaners on lettering. Control knobs/handles & trims Plastic/chrome, copper or lacquered brass Warm soapy water, soft cloth. Brass Brass polish. Oven door glass/Glass lid (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary. Oven and Grill Part Finish Recommended Cleaning Method Sides, foor & roof of oven NOT COOK & CLEAN OVEN PANELS (see below) Enamel Any proprietary oven cleaner that is suitable for enamel. CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW MANUFACTURER’S INSTRUCTIONS. Do not allow contact with the oven elements. Cook & Clean oven panels (some models only) Special enamel that partly cleans itself This surface cleans itself at 200 °C and above, or the panels can be removed and washed with hot soapy water and a nylon brush. Oven shelves, Handyrack, Grill trivet, Handygrill rack (some models only) Chrome An oven interior cleaner that is suitable for chrome. Soap flled pad. Dishwasher. Grill Pan/Meat Tin (some models only) Enamel Hot soapy water. Soap flled pad. Dishwasher. Table 5-1

21 6. Troubleshooting n n Interference with and repairs to the hob MUST NOT be carried out by unqualifed persons. Do not try to repair the hob as this may result in injury and damage to the hob. Please arrange for repair by a suitably competent person. A crack has appeared in the hob surface Disconnect the cooker immediately from the power supply and arrange for its repair. DO NOT use the cooker until after the repair. My hob is scratched Always use the cleaning methods recommended in this guide and make sure that the pan bottoms are smooth and clean. Marks from mineral deposits from water or food can be removed with a cleaning cream. However, tiny scratches are not removable but will become less visible in time as a result of cleaning. The oven fan is noisy The note of the oven fan may change as the oven heats up – this is perfectly normal. Grill not cooking properly Are you using the pan and trivet supplied with the cooker? Is the pan being used on the runners, not the foor of the compartment? Is the grill tray pushed back fully to the ‘back stop’ position? The knobs get hot when I use the oven or grill. Can I avoid this? Yes, this is caused by heat rising from the oven or the grill, and heating them up. Do not leave the oven door open. Make sure that the grill pan is pushed right back to the ‘back stop’ when grilling. Always grill with the grill compartment door open. If there is an installation problem and I don’t get my original installer to come back to fx it, who pays? You do. Service organisations will charge for their call- outs if they are correcting work carried out by your original installer. Therefore, it is in your own interest to keep track of this installer so that you can contact them as required. Power failure In the event of a failure in the electrical supply, remember to reset the clock to make sure that the timed oven continues to operate. Food is cooking too slowly, too quickly, or burning Cooking times may difer from your previous oven. Check that you are using the recommended temperatures and shelf positions – see the oven cooking guide. Then adjust the settings according to your own individual tastes. The oven is not cooking evenly Do not use a baking tray with dimensions larger than those specifed in the section on ‘General Oven Tips’. If you are cooking a large item, be prepared to turn it round during cooking. If two shelves are used, check that space has been left for the heat to circulate. When a baking tray is put into the oven, make sure that it is placed centrally on the shelf. Check that the door seal is not damaged and that the door catch is adjusted so that the door is held frmly against the seal. A dish of water when placed on the shelf should be the same depth all over. (For example, if it is deeper at the back, then the back of the cooker should be raised up or the front lowered.) If the cooker is not level, arrange for your supplier to level it for you. The timed oven is not coming on when turned on manually Is the power on? Is the clock illuminated? If not, there may be something wrong with the power supply. Is the cooker supply on at the isolator switch? Has the time of day been set? Is the key symbol [F] showing in the display to signify that the oven is locked? See the ‘Clock’ section of the instructions for more information on the key lock feature. The timed oven is not coming on when automatic cooking Has the oven knob been left in the OFF position by mistake? Is the oven locked (see above)? Oven temperature getting hotter as the cooker gets older If turning the temperature down using the oven control knob has not worked, or has only worked for a short time, then you may need a new thermostat. This should be ftted by a service person.

The bulb has probably blown. You can buy a replacement bulb (which is not covered under the guarantee) from most electrical stores. Ask for an Edison screw ftting 15 W 230 V lamp, FOR OVENS (Fig.6-1). It must be a special bulb, heat resistant to 300 °C. Before removing the existing bulb, turn of the power supply and make sure that the oven is cool. Open the oven door and remove the oven shelves. Locate the bulb cover and unscrew it by turning it counter-clockwise – it may be very stif (Fig.6-2). Taking care to protect your fngers with a glove in case the bulb should shatter, unscrew the old bulb. Screw in the new bulb clockwise and then screw the bulb cover back on. Turn on the electricity supply and check that the bulb now lights. The oven door is misaligned The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.6-3). Loosen the bottom hinge fxing screws and use the notch and a fat bladed screwdriver to move the position of the hinge to set the hinge position (Fig.6-4). Retighten the hinge screws. ArtNo.324-0007 Unscrewing the bulb cover Fig.6-2 ArtNo.324-0005 Oven light bulb Fig.6-1 ArtNo.320-0006 Oven door hinge adjustment 1 Fig.6-3 Efect of hinge adjustment – exagerrated for clarity ArtNo.320-0007 Oven door hinge adjustment 2 Fig.6-4 Centreline of hinge pin Oven door omitted for clarity

23 You will need the following equipment to complete the cooker installation satisfactorily: • Multimeter (for electrical checks) You will also need the following tools: 1. Steel tape measure 2. Cross-head screwdriver 3. Flat-bladed screwdriver 4. Spirit level 5. Pencil 6. Adjustable spanner 7. 3 mm and 4 mm Allen keys 8. 13 mm spanner or socket wrench Checking the parts: 7. Installation Dear Installer Before you start your installation, please complete the details below, so that, if your customer has a problem relating to your installation, they will be able to contact you easily. Safety Requirements and Regulations n n This cooker must be installed in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local electricity supply companies’ requirements. n n The appliance must be installed in accordance with the regulations in force and only in a well ventilated space. n n Read the instructions before installing or using this appliance. Provision of Ventilation This appliance is not connected to a combustion products evacuation device. Therefore, particular attention must be given to the relevant requirements regarding ventilation. All rooms require a window that can be opened, or equivalent, while some rooms require a permanent vent in addition to the window. Location of Cooker The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower. This appliance is designed for domestic cooking only. Use for any other purpose could invalidate any warranty or liability claim. ArtNo.050-0011 - Installer information table Installer’s Name Appliance Serial Number Installer’s Telephone Number Installer’s Company Grill pan and trivet (standard model shown) Flat oven shelf ArtNo.330-0002 - Grill pan w handle Drop shelf Handyrack ArtNo.324-0003 Handyrack Roasting tin Plinth (standard model shown) ArtNo.324-0004 Roasting tin Tall oven shelves and shelf supports Splashback (optional) ArtNo.000-0010 Tall oven shelves ArtNo.421-0002 - Splashback

24 Fig.7-4 ArtNo.090-0024 - 90 induction door clearances 130 mm min ArtNo.090-0028 - 90 cooker min spacing GENERIC 75 mm min 75 mm min 650 mm min 905 mm min 930 mm max ArtNo.090-0016 - 90 2BC min positions above cooker 410mm min 900mm min* Fig.7-1 Fig.7-2 Fig.7-3 Positioning the Cooker Fig.7-1 shows the minimum recommended distance from the cooker to nearby surfaces. The cooker should not be placed on a base. The hotplate surround should be level with, or above, any adjacent work surface. A gap of 75 mm should be left between each side of the cooker ABOVE the hotplate level and any adjacent vertical surface. For non-combustible surfaces (such as unpainted metal or ceramic tiles), this can be reduced to 25 mm. A minimum space of 650 mm is required between the top of the hob and a horizontal combustible surface. Fig.7-2 shows the suggested clearances above the cooker. *Any cookerhood should be installed in accordance with the hood manufacturer’s instructions. Surfaces of furniture and walls at the sides and rear of the appliance should be heat, splash and steam resistant. Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage and discolouration. We cannot accept responsibility for damage caused by normal use of the cooker to any material that de-laminates or discolours at temperatures less than 65 °C above room temperature. We recommend a gap of 910 mm (920 mm for induction cookers) between units to allow for moving the cooker. Do not box the cooker in – it must be possible to move the cooker in and out for cleaning and servicing. If the cooker is near a corner of the kitchen, a clearance of 130 mm is required to allow the oven doors to open (Fig.7-3). The actual opening of the doors is slightly less, but this allows for some protection of your hand as you open the door. Moving the Cooker n n On no account try and move the cooker while it is plugged into the electricity supply. n n The cooker is very heavy, so take great care. We recommend that two people manoeuvre the cooker. Make sure that the foor covering is frmly fxed, or removed, to prevent it being disturbed when moving the cooker around. To help you, there are two levelling rollers at the back, and two screw-down levelling feet at the front. Remove the polystyrene base pack. From the front, tilt the cooker backwards and remove the front half of the polystyrene base (Fig.7-4). Repeat from the back and remove the rear half of the polystyrene base.

25 ArtNo.010-0004 Moving the cooker Fig.7-5 Fig.7-7 Fig.7-6 Lowering the Two Rear Rollers To adjust the height of the rear of the cooker, frst ft a 13 mm spanner or socket wrench onto the hexagonal adjusting nut (Fig.7-5). Rotate the nut – clockwise to raise – counter-clockwise to lower. Make 10 complete (360°) turns clockwise. Make sure you lower BOTH REAR ROLLERS. Completing the Move Unfold the rear edge of the cardboard base tray. Open the grill door and right-hand oven door so that you can get a good grip on the bottom of the fascia panel as you move the oven (Fig.7-6). Carefully push the cooker backwards of the base tray. Remove the base tray. Position the cooker close to its fnal position, leaving just enough space to get behind it (Fig.7-7). n n Do not use the door handles or control knobs to manoeuvre the cooker. Repositioning the Cooker Following Connection If you need to move the cooker once it has been connected, make sure it is switched of at the supply switch before gripping under the fascia panel and lifting the front of the cooker slightly (Fig.7-6). Check behind the cooker to make sure that the electricity cable is not caught. As you progress, always make sure that the cable has sufcient slack to allow the cooker to move. When you replace the cooker, check behind it again once more to make sure that the electricity cable is not caught or trapped. Levelling the Cooker It is recommended that you use a spirit level on a shelf in one of the ovens to check for level. Place the cooker in its intended position. Take care not to twist it within the gap between the kitchen units as damage may occur to the cooker or units. The front feet and rear rollers can be adjusted to level the cooker. To adjust the height of the rear of the cooker, use a 13 mm spanner or socket wrench to turn the hexagonal adjusting nuts at the front bottom corners of the cooker. To set the front, turn the feet bases to raise or lower.

26 ArtNo.130-0010 Electrical connections single-phase L N 230 V ac 50 Hz 10 mm² max L1 N L3 L2 3N ac 230/400 V 50 Hz 6 mm² max 10 mm² max Electrical Connection This appliance must be installed by a suitably qualifed electrician to comply with the relevant electrical regulations, and also the local electricity supply company requirements. Current Operated Earth Leakage Breakers The combined use of your cooker and other domestic appliances may cause nuisance tripping, so we recommend that the cooker is protected on an individual RCD (Residual Current Device) or RCBO (Residual Current Breaker with Overload). IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED ELECTRICIAN. n n WARNING: THE APPLIANCE MUST BE EARTHED. Note: The cooker must be connected to the correct electrical supply as stated on the voltage label on the cooker, through a suitable cooker control unit incorporating a double-pole switch, having a contact separation of at least 3 mm in all poles. n n The cooker MUST NOT be connected to an ordinary domestic power point. Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (Fig.7-8 and Fig.7-9). Check that the links are correctly ftted and that the terminal screws are tight. Secure the mains cable using the cable clamp. Final Checks Hob Check Check each cooking zone in turn. Be sure to use pans of the correct size and material. Grill Check Turn on the grill control and check that the grill heats up. Oven Check Set the clock as described earlier, and then turn on the ovens. Check the oven fans start to turn and that the ovens heat up. Fig.7-8 Fig.7-9

27 Art No 215-0028 - Handrail fascia fixings ArtNo.350-0012 - Securing the plinth Fig.7-13 ArtNo.350-0010 - Fitting the plinth 1 (Kitchener) Fig.7-14 ArtNo.350-0011 - Fitting the plinth 2 (Kitchener) Outer plinth Outer plinth fxing screw Inner plinth Fig.7-15 ArtNo.215-0026 - Handle gaskets fixed ArtNo.215-0027 - Elan handle blanking plugs Fig.7-10 Fig.7-11 Fig.7-12 Final Fitting Fitting the Handles and Handrail (depending on model) Remove the 4 mm Allen screws from the doors (Fig.7-10). Fit the door handles and secure using the 4 mm screws. n n The handles should be above the fxings. Elan only: Fit the plastic blanking plugs to the fxing holes (Fig.7-11). Remove the 4 mm Allen screws from the top corners of the fascia (Fig.7-12). Fit the front handrail in position and secure using the 4 mm screws. Fitting the 1-piece Plinth Loosen the three screws along the front bottom edge of the cooker. Hook the central keyhole over the central screw. Twist and ft each end keyhole over their respective screws. Tighten the fxing screws (Fig.7-13). Fitting the 2-piece Plinth (Classic Deluxe & Professional Deluxe only) Note: When ftting the 2-piece plinth make sure to remove the 3 white plastic fxings (if present). Fit the inner plinth to the bottom front of the cooker using the 4 screws provided (Fig.7-14). Fit the outer plinth (2 screws, 1 each end) to the inner plinth. The height of the outer plinth can be adjusted by sliding it up or down via the slotted hole (Fig.7-15). Fitting the Splashback (optional) Position the splashback on the rear of the hotplate and secure with the screws supplied. Customer Care Installer: Please complete your details in this Guide, inform the user how to operate the cooker and hand oven the instructions. Thank you.

Circuit Diagram: Hob DocNo.090-0002 - Circuit diagrams - 90 ceramic GENERIC ArtNo.082-0012 - 90 Ceramic (hob) circuit diagram 1.65kW 1.1kW 2.02kW 1.56kW 1.1kW br br br b b b w br g/y b br r b bk/w br br r b bk br br r br br br b r br br r r b br br br bk r br w bk/w bk r br bk bk br b b r br bk bk br b b br br br br b bk r b r b bk b br b br br bk b r b br bk br A B C D F G Code Description A Left-hand front control B Left-hand rear control C Centre right-hand rear control D Centre right-hand front control F Right-hand control G Hob neons Code Colour b Blue br Brown bk Black or Orange r Red v Violet w White y Yellow g/y Green/yellow bk/w Black/white

Key The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz. P1 P3 1 P2 2 P1 1 3 P4 4 P095199 1 2 1 P1 P1 P2 P1 P3 1 P2 2 P1 1 3 P4 4 P033458 P033458 E r v b b b b b b br br br br bk r v bk r r v bk r w b br br br w y br y r w b br b br r o y y y y y v v y o g/y b b b w br br gy br b b bk gy b br br o v bk bk g/y w w w b w b b b o br w br br bk bk br br br bk r A1 A2 A3 J J B4 B1 B2 D H B3 G1 G2 C4 J H C3 C1 C2 F Code Description A1 Grill energy regulator A2 Grill front switch A3 Grill elements B1 Left-hand zoned oven thermostat B2 Left-hand oven thermostat front switch B3 Left-hand oven element B4 Left-hand oven fan C1 Right-hand oven thermostat C2 Right-hand oven thermostat front switch Code Description C3 Right-hand oven element C4 Right-hand oven fan D Clock F Cooling fan G1 Oven light switch G2 Oven light H Thermal cut-out J Neon Code Colour b Blue br Brown bk Black or Orange r Red v Violet w White y Yellow g/y Green/yellow bk/w Black/white

ArtNo.082-0017 - 90 ceramic - MF (classic DL) oven circuit diagram P033458 2 3 4 1 P3 P2 P1 P4 5 6 P6 P5 P028728 6 P6 5 P5 4 P4 7 P7 8 P8 2 P2 1 P1 3 P3 P033458 2 3 4 1 P3 P2 P1 P4 g/y b w bk r v br r or or bk y v w b g/y bk br gr br or br bk v br w b bk w br br br br b v r y gy w r bk v r bk b v v br br bk br r r r bk b bk b b b b b b b b b b b w gr y r or or b w b b b w b or br v b b b b b b b b w b w w w r v v b r v br br gr y b v v br br bk bk E A2 C A1 B1 A3 B3 B4 B2 B5 B6 B7 D2 I D1 D3 B8 D4 F G1 I H I H G2 I H Code Description A1 Grill front switch A2 Grill energy regulator A3 Grill elements B1 Left - hand oven front switch B2 Left - hand oven thermostat B3 Left - hand oven top element (outer) B4 Left - hand oven top element (inner) B5 Left - hand oven centre element B6 Left - hand oven fan B7 Left - hand oven base element B8 Left - hand multi - function switch Code Description C Clock D1 Right - hand oven front switch D2 Right - hand oven thermostat D3 Right - hand oven element D4 Right - hand oven fan F Cooling fan G1 Light switch G2 Oven light H Thermal cut - out I Neon Circuit Diagram: Multi-function Oven (Classic Deluxe) Code Colour b Blue br Brown bk Black or Orange r Red v Violet w White y Yellow g/y Green/yellow bk/w Black/white

ArtNo.082-0016 - 90 ceramic MF (elan) oven circuit diagram P033458 2 3 4 1 P3 P2 P1 P4 P095199 1 2 P2 P1 P028728 6 P6 5 P5 4 P4 7 P7 8 P8 2 P2 1 P1 3 P3 P033458 2 3 4 1 P3 P2 P1 P4 g/y w b w bk r br r v br r or v v y v w b g/y bk br gr br or br bk v br w b bk w br br br br b v r v y b v r bk b v v br br bk br r r r bk b bk b b b b b b b b b b b w gr y r or b v w b b b w b or br v b b b b b b b b w b w b w w b b b v br br br bk y bk E A2 C A1 B1 A3 B3 B4 B2 B5 B6 B7 D2 I D1 D3 B8 D4 F G1 I H I H G2 I H Code Description A1 Grill front switch A2 Grill energy regulator A3 Grill elements B1 Left-hand oven front switch B2 Left-hand oven thermostat B3 Left-hand oven top element (outer) B4 Left-hand oven top element (inner) B5 Left-hand oven centre element B6 Left-hand oven fan B7 Left-hand oven base element B8 Left-hand multi-function switch Code Description C Clock D1 Right-hand oven front switch D2 Right-hand oven thermostat D3 Right-hand oven element D4 Right-hand oven fan F Cooling fan G1 Light switch G2 Oven light H Thermal cut-out I Neon Circuit Diagram: Multi-function Oven (Elan) Code Colour b Blue br Brown bk Black or Orange r Red v Violet w White y Yellow g/y Green/yellow bk/w Black/white

INSTALLER: Please leave these instructions with the user. DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening. COUNTRY OF DESTINATION: GB/IE/FR/NL/BE/DE/AT/SE/LU Connections Electric 230/400 V 50 Hz Dimensions Overall height minimum 905 mm maximum 930 mm Overall width 900 mm Overall depth 600 mm (to fascia inc. splashback); 610 mm (over hotplate) Minimum space above hotplate 650 mm Refer to 'Positioning the Cooker'. Ratings ArtNo. 312-0012 - 90 Ceramic hob ratings 1.65 kW 1.1 kW 2.02 kW 1.1 kW 1.56 kW Ovens Main oven Tall oven Forced air convection Multi-function Multi-function (with Rapid Response) Forced air convection Maximum power output @ 230 V 50 Hz 2.5 kW 2.5 kW 3.7 kW 2.5 kW Energy efciency class on a scale of A (more efcient) to G (less efcient) A A A A Energy consumption based on standard load 0.85 kWh 0.90 kWh 0.90 kWh 0.95 kWh Usable volume (litres) 67 67 68 66 Size Large Large Large Large Time to cook standard load 38 minutes 41 minutes 41 minutes 49 minutes Surface area of the grid 1400 cm² 1400 cm2 1400 cm2 790 cm2 Grill 2.3 kW Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.) Fan oven variant: 14.4 kW Multi-function oven variant: 14.4 kW Multi-function oven (with rapid response) variant: 16.6 kW ArtNo.100-0002 - Technical data - 90 ceramic - GENERIC

with your appliance once it has been installed, please telephone 0870 789 5107. CONSUMER SERVICE LINES OPEN: Monday to Thursday 8am–6pm Friday 8am–5pm Saturday 9am–1pm WARRANTY Your manufacturer warranty covers goods of our own brand for defective workmanship and materials for a period of 1 year from the date of purchase. This warranty covers mechanical breakdown and proven cosmetic and manufacturing defects. You will receive an additional FREE full 12 months guarantee by registering your purchase using the FREEPOST form provided. Alternatively, call free on 0800 587 5747, quoting reference RMGX57A, or register online at www.rangemaster.co.uk. Any damage, blemishes or chips identifed upon receipt of the product must be reported within 90 days – proof of purchase may be required to establish validity. Scratches on the surface of ceramic hobs must be reported within 14 days. Scratches caused by usage are not covered. Accidental damage is not covered by the manufacturer’s warranty. For warranty compliance, the requirements are that the appliance: • Has been correctly installed in accordance with current legislation, relevant British and European Standards and Codes of Practice, by a suitably competent person registered with Gas Safe or equivalent body and, where applicable, a qualifed electrician. • Has been used solely for domestic cooking purposes. • If in use in the UK*, has not been taken abroad as a personal export. (In the Republic of Ireland conditions may vary, so consult your retailer.) • Is not second-hand or a refurbished appliance. The manufacturer’s warranty is not transferable. • Has not been subject to misuse, accidental damage or modifcation, and has not deteriorated due to normal domestic wear and tear, and the manufacturer’s recommendations concerning cleaning materials have been followed. • Has not been repaired by persons or organisations other than those authorised to act on behalf of AGA Rangemaster. Exceptions: • Items not included under the free 1 year guarantee include pan supports, griddles, wok rings, baking trays, grill pans, trivets, flters, light bulbs and other consumable accessories. • Any damage caused other than through normal use. • Breakdowns associated with cooking spillage. • Cosmetic deterioration deemed to be normal wear and tear. This warranty is in addition to your Statutory Rights. * Only certain models can be adapted for use with Mains Gas supplied in the Channel Islands and Isle of Man. OUT OF WARRANTY Service work should only be carried out by technically competent and suitably qualifed personnel. For your own safety, always make sure that work is carried out by a Gas Safe registered engineer for gas appliances or an approved electrician for electrical models. For a competitive quote and to arrange for a Rangemaster approved engineer to attend, call Consumer Services on: 0870 7895107. SPARE PARTS To maintain optimum and safe performance, we recommend that only genuine Rangemaster spare parts are used. These are available from most major spares stockists, including ourselves. Contact Consumer Services on 0870 7895107, who will be happy to help. STANDARDS Rangemaster cookers are designed and manufactured to a recognised international quality standard, which meets the requirements of BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001 for continually improving environmental procedures. Rangemaster cookers comply with the essential requirements of the appropriate European Directives, and carry the CE mark. Name of Appliance & Colour* Appliance Serial Number* Fuel Type* Natural Gas LP Gas Dual Fuel Electric Retailer’s Name & Address Date of Purchase Installer’s Name & Address Installer’s Telephone Number Date of Installation * This information is on the appliance data badge - look in the appliance instructions to fnd out where the data badge is located.

Clarence Street Royal Leamington Spa Warwickshire CV31 2AD England Tel: +44 (0) 1926 457400 Fax: +44 (0)1926 450526 E-mail: [email protected] Consumer Services Tel: +44 (0) 870 7895107 www.rangemaster.co.uk For ROI Enquiries Tel: 1850 302 502 Registered in England and Wales. Registration No. 354715 Registered Ofce: Juno Drive, Leamington Spa, Warwickshire, CV31 3RG Search Rangemaster UK Rangemaster continuously seeks improvements in specifcation, design and production of products and thus, alterations take place periodically. Whilst every efort is made to produce up-to-date literature, this booklet should not be regarded as an infallible guide to current specifcation, nor does it constitute an ofer for the sale of any particular appliance. ALSO PART OF THE RANGEMASTER COLLECTION... Refrigeration Built-in Cooking Dishwashing Sinks & Taps