Panasonic ELITE PANABOARD UB-T780 Operating Instructions Manual

Set up your projector as instructed below. About Positioning the Image • When you are projecting an image, make sure that the edge of the projected image is at least 5 mm (1/4 in.) from the screen frame. The electronic pen may not function correctly within 50 mm (2 in.) of the position sensor in the upper-left corner of the screen board. Projectable Area 5 mm (1/4 in.) 5 mm (1/4 in.) 50 mm (2 in.) 5 mm (1/4 in.) Project the Image as a Rectangle • Adjust the location of the projector to project at a right angle with the elite Panaboard. Operating Instructions (For Basi ...

Gently wipe the screen board surface with a soft, moist cloth. Notice • Do not use thinner, benzene, or abrasive chemicals to clean. (Doing so can result in discoloration.) 11. Confirm that the elite Panaboard can operate. See "Confirming the elite Panaboard Operation" (page 54). For Wall Mounting (with 1-part lower frame cover) 1. Loosely wrap the power cord with the cable tie, and plug the power cord into the AC inlet. • Connect the power cord to the elite Panaboard before installing on a wall. Power Cord 1 2 2. Insert the end of the cable tie into the ...

• For Wall Mounting (with 2-part lower frame cover) ® page 45 • For Wall Mounting (with 1-part lower frame cover) ® page 48 • For Mounting on a Stand (Sold Separately) ® page 52 Package the unit as depicted in the diagram in "Preparing for Removing the elite Panaboard from Its Packaging" (page 44), and reinforce the packaging with tape or 2 bands. Notice • When handling the screen board, hold it by the frame and not the screen board itself. (Holding the screen bo ...

apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire that is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire that is coloured BLUE must be connected to the terminal in the plug that is marked with the letter N or coloured BLACK. The wire that is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or co ...

Note • There are 2 types of lower frame covers for the elite Panaboard: a lower frame cover made from 2 parts and a lower frame cover made from 1 part. If you will be mounting elite Panaboard on a wall, the assembly procedure will differ depending on the type of lower frame cover. Follow the steps below: 1 2 2 When the lower frame cover is secured with 4 screws (2 parts) ® Page 45 When the lower frame cover is secured with 2 screws (1 part) ® Page 48 For Wall Mounting (with 2-part lower frame cover) 1. Loosely wrap the power cord with the cable tie, and plug ...

using the two-wing bolts (M5 ´ 12 mm [1/2 in.] [2 count]) included with the stand. Note • When installing the elite Panaboard on the stand, you can adjust its height to 4 different levels. When changing the height, remove the left and right screws from the back of the elite Panaboard, and securely insert them at the desired height. Torque (greater than 1 N·m [10 kgf·cm (9 lbf·in.)]). elite Panaboard Height Screw Position -100 mm (-3 7/8 in.) Highest Standard 2nd from top +100 mm (+3 7/8 in.) 2nd from bottom +200 mm (+7 7/8 in.) Lowest 5. W ...

• When drilling the holes and installing the wall mounting plates, follow the procedure in "Wall Types and Installation Procedures" (page 38). 5. Mount the elite Panaboard on the wall. See "Assembling the elite Panaboard" (page 45). Wall Types and Installation Procedures The method for attaching the wall mounting plates to the wall will vary depending on the wall's structure. Three available options are listed below. Other methods may be necessary depending on the wall. Metal or Concrete walls Stud plugs (not included) are needed. Drill ...