ParaBody PBF005C Product Assembly Instruction Sheets

8. Attach sixteen (16) PARAGLIDE STRIPS to the SWIVEL SLEEVE (ONE IN EACH CORNER, BOTH ENDS) as shown in (DETAIL A) using the following steps: • Thoroughly clean all inside surfaces where the PARAGLIDE STRIPS are to be attached. PARABODY INC. • Remove paper backing from the PARAGLIDE STRIPS and firmly apply them to all shown surfaces . (16 places) 9. Assemble the SWIVEL SLEEVE to the LEFT side ofthe BENCH FRAME as shown in (DETAIL A) using one (1) 112 X 5 IN. BOLT, one (1) 112 IN. WASHER, and one (1) 1/2 IN. LOW HEIGHT LOCK NUT. (NOTE: TIGHTEN SWIVEL SLEEVE ENOUGH THAT IT SWIVELS FREELY, YET IT DOESN'T WOBBLE) 10. nsert two (2) 1-3/4 IN. SQ. END CAPS into each end ofthe ADJUSTABLE SLIDE. 11. Insert the multiple hole end of the ADJUSTABLE SLIDE into the SWIVEL SLEEVE. (NOTE: BE SURE SWIVEL SLEEVE IS IN THE PROPER POSITION, SEE DRAWING) Attach the other end to the ADJUSTABLE SLIDE MOUNT on the BACK PAD, using one (1) 112 X 2-1/2 IN. BOLT, two (2) 1/2 IN. WASHERS, and one (1) 112 IN. LOW HEIGHT LOCK NUT. (TIGHTEN UNTIL SNUG, THEN BACK OFF 1/4 IN. TURN) FLAT/INCLINE BENCH PBF005C 12. To adjust SEAT PAD andlor BACK PAD use the two (2) 3/8 IN. L-PINS. (SEE DRAWING) 13. The extra 3/8 IN. L-PIN, and TIIUMBSCREW is for securing the BODYSMITH ATTACHMENTS at the front of the FLATIINCLINE BENCH. (SEE DRAWING) 4 PRODUCT ASSEMBLY INSTRUCTION SHEETS TOOLS REQUIRED FOR ASSEMBLY • 9/16 INCH SOCKET • ADJUSTABLE WRENCH • RUBBER MALLET or HAMMER REVISION: B If you experience any probiem with the assembiy of this product, piease contact your deaier or your PARABODY Customer Service Representative at: 1-800-328-9714

PBF005C FLAT/INCLINE BENCH ASSEMBLY INSTRUCTIONS SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY HARDWARE: ITEM NAMEIDESCRIPTION QTY • THE BODYSMITH FLAT/INCLINE BENCH MUST BE ASSEMBLED ON A FLAT, LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 1/2 X 5 IN. BOLT 1 3/8 X 3 IN. BOLT 6 1/2 X 2-1/2 IN. BOLT 1 3/8 X 1-1/4 IN. BOLT 6 1/2 IN. WASHER , 3 3/8 IN. WASHER 18 3/8 IN. LOCK WASHER 10 3/8 IN. NlIT 4 1/2 IN. LOW HEIGHT LOCK NlIT 2 3/8 IN. LOW HEIGHT LOCK NlIT 2 3/8 IN. L-PIN 3 2 IN. SQ. END CAP 4 1-3/4 IN. SQ. END CAP 2 PARAGLIDE STRIPS 16 THUMBSCREW 1 *** IMPORTANT *** KEEP ALL LOOSE FRAME CONNECTIONS LOOSE UNTIL INSTRUCTED IN THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN WELDMENTSIPARTS: ITEM NAMEIDESCRIPTION QTY 1. 2. 3. 4. 5. 6. 7. 8. 9. BASE LEG (pB2365-1) 1 BENCH FRAME (pB2587-1) 1 ADJUSTABLE SLIDE MOUNT (pB2596-1) 1 ADJUSTABLE SLIDE (pB2590-1) 1 SEAT BRACKET (pB2352-1) 4 SWIVEL SLEEVE (pB2592-1) 1 SEAT PAD (pB2358-1) 1 BACK PAD , (pB2359-1) 1 FRONT RUNNER (pB2591-1) 1 2 1. 2. 3. 4. 5. 6. 7. Insert four (4) 2 IN. SQ. END CAPS into each end of the BASE LEG, and FRONT RUNNER. SECURELY assemble the BASE LEG to the REAR CONNECTOR on the BENCH FRAME, using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, two (2) 3/8 IN. LOCK WASHERS, and two (2) 3/8 IN. NUTS. SECURELY assemble the FRONT RUNNER to the FRONT CONNECTOR on the BENCH FRAME, using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, two (2) 3/8 IN. LOCK WASHERS, and two (2) 3/8 IN. NlITS. (SEE DRAWING) Assemble four (4) SEAT BRACKETS to the BENCH FRAME as shown on drawing, using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. LOW HEIGHT LOCK NlITS. (NOTE: TIGHTEN SEAT BRACKETS ENOUGH THAT THEY SWIVEL FREELY, YET THEY DON'T WOBBLE) SECURELY assemble the SEAT PAD to the FRONT set of SEAT BRACKETS, using two (2) 3/8 X 1- 1/4 IN. BOLTS, two (2) 3/8 IN. LOCK WASHERS, and two (2) 3/8 IN. WASHERS. SECURELY assemble the BACK PAD to the REAR set of SEAT BRACKETS, using two (2) 3/8 X 1- l/4 IN. BOLTS, two (2) 3/8 IN. LOCK WASHERS, and two (2) 3/8 IN. WASHERS. SECURELY assemble the ADJUSTABLE SLIDE MOUNT to the BACK PAD, using two (2) 3/8 X 1- l/4 IN. BOLTS, two (2) 3/8 IN LOCK WASHERS, and two (2) 3/8 IN. WASHERS. (NOTE: THE OFFSETTING FLANGE ON THE ADJUSTABLE SLIDE MOUNT SHOULD BE LOCATED ON THE LEFT SIDE OF THE BACK PAD. SEE DRAWING) 3

I ' <2PU'5~~ I - -----> ~~ ~ " ,----- " '('''' ~~ '- !", I 'JJ VJ~ ,J "1'1' 31B X 1'/<.4' ( ~- BOLT 3/£WASHffi ~~I.:::,t:.AIERACK::- rZPLLS,) CHl,",,\ ' '" PLLS, ~ , 3IB~ WASHER [2 P.llS.) ?;.. 318 LOW tIT. 1.DC,KNlJT 3/8' L - PIN ~ 3/BX~ ~ BOLT ~ ~ BACK LJ ~ ~ ---I;! E.ND CAP 1"2. PLCS) FRONT RUNNER. AID.5LlD- M to. DUN\" ~ BENl:.H FRAME "5/5 X3 BOLl, ~ '013l>l'5Q 12. P • END CAP LCS.) 3/80 LOc.KWASHER ~~:-- " .~ "3IS WASHER 3/B [2. PLCS.) X 11/".(500 (2. PL.CS.) , , 3/8' LOU(. 11 WASHERS~ / 1.L.1 PliS.) -®~~ c;n .. 3(£' 11 I ._."H-~~------- I WASHER 3/B WASHElZ- 3113' NUT (7. PLCS;) (2. PLC.S.) (!..j PUS,) () DETAIL''I{'/' ___ll./ SW IVEL SLEF'lE) AD...I. 5L1D~ , l ~ I 'IL" w "'"'-.£:l 1 ASHER f.!!;.~. SEE REAR C.ONNE.CTOR . 'lL" X2J/2...· BOLT DETAIL "A" SCALE: -;:-lJLL WIJ.RNIN(;, LABEl- -~ LifE t