Screen Technics ELECTRICINEMA Instruction Manual

Thank you for purchasing a Screen Technics Projection Screen, please ensure that you read the following instructions fully before to install this product. Wall Mounting Instructions 1. Measure the wall where the screen is to be installed and mark with a pencil the desired height to top of screen case and also the centre of the screen. 2. Measure the length of screen canister along the top surface and mark the centre of the canister with a pencil, to assist in lining up the screen when mounting. 3. Determine the best positions for the wall brackets, allowing that in Gyprock or in low strength walls the brackets will be screwed into a timber stud. In more solid walls, such as masonry, position the brackets approx 150mm in from the canister end. The brackets should be no more than 450mm in from each end. You must use a minimum of 3 off wood screws per bracket or 2 off Dyna-bolts, for masonry walls and you must be satisfied that the attachment is strong enough for the a safe installation.

of screen canister. 4. You may need to remove the bottom clip in order to screw brackets to wall, please ensure to replace them afterwards. 5. Using two people install the screen by placing the screen canister into the bottom of the bracket clips and pivoting back the canister to slot the top pins into the T channels running along the top of the canister (you may have to remove any tape that is in the way).

hooked into the T section of the screen canister. Ceiling Mount Instructions Below is a photo showing a side view using the brackets for ceiling fixing, you would follow the instructions for the wall mounting system, with the only difference being the screen is mounted hard against the ceiling. It is important that adequate support is supplied by the ceiling structure to support the screen and to ensure a safe installation. Never rely just on the Gyprock for attachment. Please follow these instructions to ensure trouble free operation;  Ensure that the screen is free to descend and that any adhesive tape that has been placed on the bottom of the screen (to stop movement during transport) has been removed.  When installed, the opening in the canister should be down and at the back of the canister. This will put the motor on the left-hand side of the screen, as viewed by the audience.  Cleaning of the screen is best achieved by first dusting the surface with a feather duster, then to remove any stubborn marks, use a small amount of mild detergent and warm water on a clean white lint free cloth. Do not use a saturated cloth, as this may leave a watermark, only a damp one. It is most important that you only treat the actual mark by this process and not the entire surface.  The Motor is 240 V 50Hz and draws 1.2 A.  The screen drop is set and tested at the factory. Therefore, any damage caused to the screen from limit re- adjustment is not covered by warranty.

After the installation of the ElectriCinema Connect is completed, plug the screen into a standard power point and turn on. Point 1 - The screen comes with a standard 3 pin power plug which suitable for Australian and New Zealand GPO’s (general power outlet). The projection screen can be operated in three ways:  2 Channel Infra Red Remote Control - supplied  Impulse wall Switch – Up & Down (supplied by others)  Dry Contact Closure – (Two Momentary Contacts) , One for Up and One for Down connected from common to up and down. Command is send when contact is released - for connection to control systems. Point 2 - Infra Red Remote Control The projection screen is packaged with a 2 channel Infra Red Transmitter and a 300mm long IR Sensor, already connected to the screen and exiting the rear of the canister. Position the IR Sensor Eye with double sided tape or a U Pin, so that it can be seen from where you wish to operate the projection screen, and use the up and down buttons on the transmitter on channels 1 or 2 to operate the screen. The following procedures require access to the Connect Module and as such you MUST remove all power from the screen before removing the end canister plate as electrocution may occur. Point 3 - Impulse Wall Switch (supplied by others). The Connect Module equipped projection screen can also have simple wall switch operation, although due to interior décor choices the actual switch itself is not supplied with the screen and needs to be sourced. The Connect Module comes with a pluggable terminal block, located as plugged into the module, so that you can wire the wall switch to the connector and then plug it into the control module itself, you may leave the IR Sensor eye lead in place or remove it at this stage and connect the wall switch connector to the module. Point 3 - Dry Contact Closure This is the industry standard method of switching a projection screen via a Building Control System, such as AMX, Crestron, C-Bus, etc…etc It is operated on a momentary contact switching standard with an Open, Close and Common input port. It utilises the same connection as the above described Impulse Wall Switch.

RJ12 6 Core Straight Through Data cable can link up to 9 devices for multiple products. Point 5 – (Optional Accessory ) Low Voltage Trigger Relay Module / Item No 3500404 Switches device upon the receipt of 5v to 24v DC from a projectors low volt output port, plugs into the left hand RJ12 on the module. Once you have chosen your switching method ensure that you refit the screen canister end plate before applying mains power to the screen. Note: As the Infra Red control is also used to perform a Connect module reset in case you are troubleshooting any performance issues, it is recommended that the IR cable be left attached to the module even if it is not the chosen operating method for your installation. Should you have any questions regarding the installation of our projection screens please call our technical sales desk on +61 2 4869 2100 for assistance. Limit Setting for Connect ElectriCinema Screens The following instructions are for the adjustment of the limit switches that alter the upper and lower stop positions on "Connect" ElectriCinema Screens only Where are The Limit Switches? At the opposite end to the power cable (ie on the Right Hand Side). One switch is accessible through the slat rod opening and the other is behind a rubber grommet towards the front of the canister. Which Switch is for Up and Down? Down switch - Accessible through the rubber grommet Up switch - Accessible through the slat rod opening What Tools do I Need? Either the limit setting tool (supplied), a narrow tip screw driver (less than 4mm) or a 4mm Allen Key Which Way do I Turn the Switch? Clockwise always increases the amount of rotation (travel) of the motor. Anti-clockwise always reduces the amount of rotation (travel) of the motor. So pick the switch responsible for the limit position, up or down. Clockwise turning of the switch will always let the motor travel further in that direction. Anti-clockwise turning of the switch will lessen the amount of travel in that direction. Can I adjust the switch while the screen is sitting on the limit - ie fully up or down? Clockwise adjustment? – YES. But it is better to back the screen away from the limit and then adjust

sitting on the limit. Never attempt this. You must back the screen away from the limit before adjustment. After adjustment you will need to run the screen up and down to pick up the new limit Will I void the product warranty if I damage the screen whilst making these adjustments? Yes. Should you have any questions regarding the installation of our products please call our sales desk on +61 2 4869 2100 for assistance