Sekonic SR-6500 Operating Manual

Appendix ■Sheet creation reference You can use paper that you make yourself with this device in addition to the optional paper that we offer. If you make your own paper, follow the specifications below. (1) Sheet size Height 148.0-355.6mm Width 82.55-228.6mm Do not cut or round the corners on the reference side (timing mark side). (See P. ⅳ) (2) Weight and thickness (3) Paper quality OCR paper, bond paper, or recycled OCR paper. * Cut corners and round corners They help you to easily check if paper is placed in the right direction, and help you to mana ...

Selected paper discharge sensor Printing start sensor [Main body unit] Error Explanation Code Procedures for Resolving and Clearing Errors Form left in hopper A sheet left in the paper feeding detection sensor. T1 ...

Printer settings ■Printer control .................................................................................................. 49 ■SR-6500 mode 1. Character size setting.................................................................................... 50 2. Character interval setting............................................................................... 51 ■SR-9000 mode 1. Character size setting........................................................ ...

This device can be set “A4 size (11.7inch)” or “14inch size” “A4 size (11.7inch)” mode is use for A4 size (length: 297mm) or short length sheet. “14inch size” is use for over 298mm length sheet. Note *“A4 size (11.7inch)” mode is for reading of A4 (length :297mm) size or short length paper. (The line speed will be 1,240mm.) *“14inch size” mode is for reading over 298mm (length) paper. (If set “14inch size” to read of A4 (length :297mm) or short length paper, it line speed will be slow.) *The printing position and Barco ...

a gap and a floating on the adsorption aspect. In case of a certain pressing the panel side, make stick. 2) Because the aliging roller section has used the magnet, do not bring close a floppy disk and magnetic card etc... Aligning roller Operation ■Loading paper 3. Use the index markings on the side guide to determine how many sheets maximum should be placed on the paper feed table. Errors may occur if too many sheets are placed on the table. Side guide index markings ...

This device is equipped with USB and RS-232C interfaces. When connecting the OMR, the connection with USB in order to show the performance of this device sufficiently is recommended. When using USB connection, use the USB driver inside CR-ROM that came with this device. When replacing the OMR SR-9000 series with this device, you can use the RS-232C interface. ※ 1 When using the RS-232C interface, set the same communication setting on this device and the computer. Set the computer communication setting by checking your computer or software manuals. ※ 1)There ...

1 500,000 or 3 years - Driving roller / 2 2 500,000 or 3 years - Driving roller / 3 2 500,000 or 3 years - Driving roller / 4 1 500,000 or 3 years - Driving roller / 5 1 500,000 or 3 years - Paper discharge roller/1 2 500,000 or 3 years - Stacker unit * Replacement periods may differ depending on usage conditions (usage frequency, quality of paper used, etc.) Driving roller/2 Paper discharge roller/1 Driving roller/1 Driving roller/4 Driving roller/5 Driving roller/3 Service schedule ...

1. Turn the power off. 2. Open the cover on the top of stacker unit. 3. Loosen the barcode unit position fixing screw, move the barcode unit according to barcode position, and tighten the screw to secure it. * The scale on the positioning sticker indicates center of the barcode position from the edge of the paper(Timing mark side). The barcode position is determined by aligning the barcode unit position fixing screw with the scale on the sticker. 4. Turn the power on. 1 0 0 1 0 0 5 0 5 0 BAR CODE/V （mm） 1 5 0 1 5 0 2 0 0 2 0 0 Positioning scr ...