Sharp MD-MS701H Service Manual

CONTENTS Page SAFETY PRECAUTION FOR SERVICE MANUAL ............................................................................................................... 2 SPECIFICATIONS ................................................................................................................................................................. 3 NAMES OF PARTS ............................................................................................................................................................... 4 OPERATION MANUAL .......................................................................................................................................................... 5 DISASSEMBLY ...................................................................................................................................................................... 8 REMOVING AND REINSTALLING THE MAIN PARTS ......................................................................................................... 9 ADJUSTMENT ...................................................................................................................................................................... 10 NOTES ON SCHEMATIC DIAGRAM .................................................................................................................................. 28 BLOCK DIAGRAM ............................................................................................................................................................... 29 SCHEMATIC DIAGRAM/WIRING SIDE OF P.W.BOARD ................................................................................................... 30 WAVEFORMS OF CD CIRCUIT .......................................................................................................................................... 39 TROUBLE SHOOTING ........................................................................................................................................................ 40 FUNCTION TABLE OF IC.................................................................................................................................................... 43 PARTS GUIDE/EXPLODED VIEW PACKING METHOD (FOR UK ONLY) • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. MD-MS701H MD-MS702H(BL) MD-MS702H(GY) SERVICE MANUAL SHARP CORPORATION No. SX789MDMS702H This document has been published to be used for after sales service only. The contents are subject to change without notice. Illustration: MD-MS701H

SAFETY PRECAUTION FOR SERVICE MANUAL Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements. However, the following precautions must be observed during servicing to protect your eyes against exposure to the laser beam. (1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens. (2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping. (3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup. (4) Under no circumstances look directly into the Pickup Lens at any time. (5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT Laser Diode Properties Material: GaAIAs Wavelength: 785 nm Pulse time: Read mode: 0.8 mW Continuous Write mode: max 10 mW 0.5 min cycle 1.5S Repetition VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERAS. KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1. CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED AVOID EXPOSURE TO BEAM . VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. ADVARSEL - USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN. VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖN LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEN. VARNING - OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSETTELSE FOR STRÅLING. VARO ! Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteeseen. VARNING! Osynlig laserstralning när denna del är öppnad och spärren är urkopplad. Betrakta ej strälen. Precaution to be taken when replacing and servicing the laser pickup. The following precautions must be observed during servicing to protect your eyesagainst exposure to the laser. Warning of possible eye damage when repairing: If the AC adaptor or batteries are connected when the top houising (disc cover) of the unit is removed, and the PLAY key is pressed, the laser will light up during docus access (2-3 seconds). (Fig. 2-1) During the operation, the laser will lesk from the opening btween the magnetic head and the mechanical chassis (Fig. 2-2). In order to protect your eyes, you most not look at the laser durnd repaor. Before repaoring be sure to disconnect the AC adaptor and remove the batteries. Figure 2-1 Figure 2-2 Magnet Head Lasar Beam Optical Pick-Up Main PWB Disc motor Mechanism Chassis Magnet head Optical pick-up Disc cover

FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. General Power source: DC 3.6 V (rechargeable lithium-ion battery x 1) DC 5 V (AC adaptor) AC 110 - 240V, 50/60 Hz DC 3V: Separately available battery case, AD-M70BC (commercially available, "AA" size, alkaline battery x 2) DC 4.5V: Separately available car adaptor, AD-CA20X (for cars with a 12-24V DC negative earth electrical system) Power consumption: 0.15 A (AC adaptor) 4 W Output power: RMS; 20 mW (10 mW + 10mW) (0.2% T.H.D.) Charging time: Approx. 2.5 hours (When using the AC adaptor included with the unit) Battery life: The continuous recording time is for analogue input when the volume level is set to "VOL 0". The continuous play time shows the value when the volume level is set to "VOL 15". The above values are the standard values when the unit is charged and used at an ambient temperature of 20oC. The operating time when using alkaline batteries may be different, depending on the type and manufacturer of the batteries, and on the operating temperature. Input sensitivity: Output level: Dimensions: Width: 87.0 mm (3-7/16") Height: 29.4 mm (1-3/16") Depth: 81.5 mm (3-7/32") Weight: MD-MS701H: 216 g (0.48 lbs.) with rechargeable battery MD-MS702H: 219 g (0.49 lbs.) with rechargeable battery Input socket: Line/Mic/optical digital, microphone (powered by the main unit) Output socket: Headphones (impedance: 32 ohms)/remote control unit MiniDisc Recorder Type: Portable MiniDisc recorder Signal readout: Non-contact, 3-beam semi-coductor laser pick-up Audio channels: Stereo 2 channels/monaural (long- play mode) 1 channel Frequency response: 20 - 20,000 Hz (± 3 dB) Rotation speed: Approx 400 - 900 rpm Error correction: ACIRC (Advanced Cross Interleave Reed-Solomon Code) Coding: ATRAC (Adaptive TRansform Acoustic Coding), 24-bit computed type Recording method: Magnetic modulation overwrite method Sampling frequency: 44.1 kHz (32 kHz and 48 kHz signals are converted to 44/1 kHz, and then recorded.) Wow and flutter: Unmeasurable (less than ±0.001% W.peek) Specifications for this model are subject to change without prior notice When using the rechargeable battery (fully charged) included with the unit When using two, commerically available, high capacity, "AA" size, alkaline batteries (in the separately available battry case) When using two, commercially available, high capacity, "AA" size batteries with the rechargeable battery (fully charged) Continuous recording: Approx. 3.5 hours Continuous recording: Approx. 4 hours Continuous recording: Approx. 7.5 hours Continuous play: Approx. 5 hours Continuous play: Approx. 8 hours Continuous play: Approx. 13 hours Headphones — 10 mW + 32 ohms 10 mW LINE 300mV — 50 kohms (-12dB) Maximum output level Specified output SPECIFICATIONS Recording Reference input Input level level impedance MIC H 0.25 mV 10 k ohms MIC L 2.5 mV 10 k ohms LINE 100 mV 20 k ohms Load impedance

NAME OF PARTS Remote Control Unit 1. Synchro Recording Indicator 2. Character/Time Information Indicator 3. Record Indicator 4. Repeat Indicator: 5. Random Indicator 6. Disc Mode Indicator 7. Total Track Number Display 8. Track Number Indicator 9. Battery Indicator: 10. Headpones Socket 11. Hold Switch 12. Play Mode Button 13. Volume Buttons: +, - 14. Bass Button 15. Display Button 16. Play/Pause Button: 17. Stop/Power Off Button: 18. Fast Reverse/Fast Forward Buttons: / Main Unit 1. Monaural Long-Play Mode Indicator 2. Record Indicator 3. Level Meter 4. Repeat Indicator: 5. TOC Indicator 6. Battery Indicator: 7. Random Indicator 8. Track Number Indicator 9. Character/Time Information Indicator 10. Synchro Recording Indicator 11. Disc Mode Indicator 12. Disc Name Indicator 13. Track Name Indicator 14. Remaining Recording Time Indicator 15. Total Track Number Display 16. Record/Track Mark Button 17. Volume/Name Select Buttons: +, - 18. Display/Lowercase Characters Button 19. Character Button 20. Stop/Power Off/Charge Button: /:OFF 21. Play/Pause Button: 22. Fast Reverse/Fast Forward/Recording Level Control/Cursor Buttons: / 23. Enter/Fast Play/Synchro Button 24. Editer/Auto Mark/Time Mark Button 25. Eject Lever 26. Bass/Delete Button 27. Mode/Insert Button 28. Microphone Input Socket 29. Hold Switch 30. Rechargeable Lithium-Ion Battery Compartment 31. Optical/Line Input Soket 32. Headphones Soket 33. 5V DC Input Sokets 34. Battert Case Connection Terminals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 29 34 30 33 28 31 32 RANDOM TOTAL 1 REC SYNC 12 13 14 11 15 16 17 18 10 1 6 2 3 4 5 7 8 9

Even if the maximum recording time of a MiniDisc has not been reached, “DISC FULL” or “TOC FULL” may be displayed. When the number of tracks used reaches the limit, regardless of the remaining recording time, further recording will be impossible. (Maximum number of tracks: 254) If a MiniDisc has been recorded or edited repeatedly or if a MiniDisc has scratches on it, it may not be possible to record the maximum number of tracks on it. Even if the number of tracks and the recording time have not reached the limit, “DISC FULL” may be displayed. If there are scratches on a disc, the unit will automatically avoid recording in those areas. The recording time will be reduced. Even if several short tracks are erased, the remaining recording time may not show an increase. When the remaining recording time of a disc is displayed, short tracks less than 8 seconds long may not be included in the total. Two tracks may not be combined in editing. For MiniDiscs on which repeated recording and editing operations were performed, the COMBINE function may not work. The total of the recorded time and time remaining on a disc may not add up to the maximum possible recording time. A cluster (about 2 seconds) is normally the minimum unit of recording. So, even if a track is less than 2 seconds long, it will use about 2 seconds of space on the disc. Therefore, the time actually available for recording may be less than the remaining time displayed. If there are scratches on discs, those sections will be automatically avoided (no recording will be placed in those sections). Therefore, the recording time will be reduced. When recorded tracks are played back using the cue and review operations, some sounds may be skipped. For MiniDiscs on which repeated recording and editing were performed, some sounds may be skipped whilst cueing and reviewing. A track number can be created in the middle of a track. If there are scratches or dust on a MiniDisc, the track numbers following that track will be increased by one. MiniDiscs are recorded using a different system than is used for cassette tapes or DAT recordings. Therefore, the following conditions may be encountered, depending on how the disc has been recorded or edited. These are due to system limitations, and should be considered normal. MINIDISC SYSTEM LIMITATIONS OPERATION MANUAL Rechargeable battery power When the rechargeable battery is used for the first time or when you want to use it after a long period of disuse, be sure to charge it fully. 1 Open the rechargeable battery com- partment cover. 2 Insert the rechargeable battery. Insert the side with the arrow first. 3 Close the rechargeable battery com- partment cover. 4 Plug the AC adaptor into the AC socket, and then insert the plug on the AC adaptor lead into the DC IN 5V socket. 5 Press the /:OFF button twice to begin charging. “ ” will appear, and the battery will begin charging. Battery charging will be complete in 2.5 hours. When the charging is com- plete, “ ” will go out. POWER SOURCE Notes: After charging has been completed, the AC adaptor may be left connected. (For example, when charging at night) The battery will not be charged when- ever the power to the main unit is turned on. If the AC adaptor is removed from the main unit or from the AC socket whilst charging, “ ” will not disappear for about 1 minute. This is normal. Do not force open the rechargeable battery cover too wide. Do not fit the separately available bat- tery case when charging the internal battery. This unit can be used with 4 different power sources: a rechargeable battery, an AC adaptor, a separately available battery case (AD-M70BC), and a separately available car adaptor (AD-CA20X). 1 2 5 4 :OFF Mark To the DC IN 5V socket AC 110-240V, 50/60 Hz Insert securely, all the way in.

Checking the remaining amount of battery charge The remaining amount of battery charge is shown by the battery indicator ( ) dur- ing operation. < How to read the battery indicator > When the battery is completely dis- charged, the whole battery indicator will flash. Recharge the battery or replace the alkaline batteries with new ones. When the battery has run completely out, “BATT EMPTY” (main unit) and “Lo BATT” (remote control unit) will appear. Then, the power will be disconnected automatically. Notes: When the AC adaptor included with this unit or a separately available car adaptor is used, the battery indicator will not be shown. The number of bars shown in the battery indicator may increase or decrease, de- pending on the operation being per- formed. This is normal. When the rechargeable battery and the alkaline batteries are used at the same time, the rechargeable battery is used first, and then the alkaline batteries. Since the battery indicator shows the re- maining amount of the particular battery being used, the number of bars will in- crease when the unit switches to the alka- line batteries. CONVENIENT OPERATION OF THE UNIT Battery indicator Charging is needed. When the battery is completely charged When the battery needs charging, it is impossible to start recording or editing. RECORDING USING A SEPARATELY AVAILABLE DIGITAL CABLE There are cases where digital recording may be impossible. In the following cases digital recording is impossible, even if you are using digital cables. When you attempt to make a new digital recording from a track that was digitally recorded on a MiniDisc MiniDiscs are designed so that only first generation digital copies can made, further digital copies are pre- vented by the SCMS (Serial Copy Man- agement System). Recording Playback CD player, MD player, etc. Digitally recorded MiniDisc Digital cable Recording Playback Digital cable Analogue recording is possible. Moisture condensation In the following cases, condensation may form inside the unit. Shortly after turning on a heater. When the unit is placed in a room where there is excessive steam or moisture. When the unit is moved from a cool place to a warm place. When the unit has condensation inside, the disc signals cannot be read, and the unit may not function properly. If this happens, remove the disc. The condensation should evaporate in approximately 1 hour. The unit will then function properly. TROUBLESHOOTING If trouble occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal sup- ply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1. Unplug the AC adaptor from the AC socket. 2. Remove the battery. 3. Leave the unit completely unpowered for approximately 30 seconds. 4. Plug the AC adaptor back into the AC socket and retry the operation. If strange sounds, smell or smoke come out of the unit or an object is dropped into the unit, remove the AC adaptor from the AC socket immediately and contact an au- thorised Sharp service centre. Many potential “problems” can be resolved by the owner without calling a service tech- nician. If something seems to be wrong with this product, check the following before calling your authorised SHARP dealer or service centre. PROBLEM CAUSE The unit does not turn on. Is the AC adaptor disconnected? Is the battery exhausted? Is the unit in the safety mode? Has condensation formed inside the unit? Is the unit being influenced by mechanical shock or by static electricity? No sound is heard from the headphones. Is the volume set too low? Is the remote control unit or the headphones plugged in? Are you trying to play a MiniDisc with data on it instead of a MiniDisc containing music? When the operation buttons are pressed, the unit does not respond. Is the unit in the safety mode? Is the battery exhausted? Is the remote control unit plug or the headphone plug inserted firmly? Some sounds are skipped. Is the battery exhausted? Is the unit being subjected to excessive vibration? The MiniDisc cannot be ejected. Has the track number or character information been written on the disc yet? Is the unit in the recording or editing mode? Recording and editing are impossible. Is the MiniDisc protected against accidental erasure? Is the unit connected properly to the other equipment? Is the AC adaptor unplugged or did a power failure occur whilst recording or editing? Is the unit in the safety mode?

Error messages Meaning Remedy BATT EMPTY The battery run down. Charge the rechargeable battery or replace the alkaline batteries (or use the AC adaptor for power). BLANK DISC Nothing is recorded. Replace the disc with a recorded disc. Can't COPY No copy can be made because of the SCMS copyright system. Record using the analogue cable. Can't EDIT A track cannot be edited. Change the stop position of the track and then try editing it. Can't REC Recording cannot be performed correctly due to vibration or shock in the unit. Re-record or replace it with another recordable disc. Can't WRITE Editing is impossible. Check the number of tracks. DEFECT The disc is scratched. If the sound you hear is not right, try recording again. Replace the disc with another recordable disc. Din UNLOCK Poor connection of the digital cable. Connect the digital cable securely. DISC ERROR The disc is damaged. Reload the disc or replace it. DISC FULL The disc is out of recording space. Replace it with another recordable disc. HOLD The unit is in the safety mode. Return the HOLD switch to its original position. LOCKED LOCK ERROR The EJECT lever was moved during recording or editing. Turn off the power and remove the MiniDisc. NO DISC A disc has not been loaded. Load a disc. PB DISC PROTECTED The disc is write protected. You tried to record on a playback- only disc. Move the write protection knob back to its original position. Replace it with a recordable disc. POWER ? Improper power is being supplied. Use one of the specified power sources. SORRY Since a track number is currently being located or written to, the unit cannot accept your command. Wait for a while and try the operation again. SYSTEM ERR You have come to the conclusion that the unit is out of order. To have it repaired, go to the distributor where you purchased the unit. TEMP OVER The temperature is too high. Turn off the power, and wait for a while. TOC ERROR A large portion of the disc has been damaged. Replace it with another recorded disc. TOC FULL There is no space left for recording character information (track names, disc names, etc.). Replace it with another recordable disc. Tr. Protect The track has been protected from being erased. Edit the track with the device on which it was recorded. U TOC ERROR A large portion of the disc has been damaged. There is an error in the recorded signal. Replace it with another recorded disc. Erase all of the signal errors, and then try recording again. ? DISC A disc which contains data other than music was played. There is an error in the signal from the disc. A disc which contains non-music data cannot be played. Replace it with another recorded disc. ERROR MESSAGES

1 Bottom Cabinet 1. Open the battery Lid. 8-1 2. Screw ..................... (A1) x6 2 Top Cabinet 1. Screw ..................... (B1) x4 8-1 2. Flat Cable ............... (B2) x2 3 Main PWB 1. Screw .................... (C1) x2 8-2 2. Flat Cable ...............(C2) x3 4 Mechanism Unit 1. Lift the left side, and remove 8-3 in the arrow direction. DISASSEMBLY Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take the battery and minidisc out of the unit. 2. When disassembling the machine, be sure to withdraw the power plug from the socket in advance. 3. When disassemble the parts, remove the nylon band or wire holder as necessary. To assemble after repair, be sure to arrange the wires as they were. If a screw of different length is fitted to the MD mecha- nism (the screw of the part to be fitted to the MD mechanism chassis), it may contact the optical pickup, resulting in malfunction. 4. When repairing, pay due attention to electrostatic charges of IC. REMOVAL PROCEDURE STEP FIGURE Bottom Cabinet Top Cabinet Center Cabinet Pull (A1)x1 Ø1.4x2mm (A1)x1 Ø1.4x2mm (A1)x2 Ø1.4x2mm (A1)x2 Ø1.4x2mm (B1)x1 Ø1.4x2mm (B1)x1 Ø1.4x2mm (B1)x2 Ø1.4x2mm Figu re 8-1 Figure 8-2 Mechanism Unit Figure 8-3 Caution: 1. Handle carefully the main PWB and flexible PWB. After removing the flexible PWB (*1) for optical pickup from the connector, wrap the front end of flexible PWB in conduc- tive aluminum foil so as to protect the optical pickup from electrostatic damage. 2. When removing the mechanism from the cabinet or when installing it, it is advisable to rotate the unit lock plate to lower the holder section. (C1)x1 Ø1.7x2.5mm (C1)x1 Ø1.7x2.5mm Pull Pull Pull Pull Pull Pull Pull Pull (B2)x1 (B2)x1 (C2)x1 (C2)x1 (C2)x1 Main PWB

REMOVING AND REINSTALLING THE MAIN PARTS Remove the mechanism according to the disassembling meth- ods 1 to 3. (See Page 8.) How to remove the spindle motor (See Fig. 9-1.) 1. Remove the solder joint (A1) x 1 of flex PWB. 2. Remove the stop (A2) x 3 pcs. and remove the spindle motor. Figure 9-5 Flexible PWB solder joint (A1) x1 Spindle Motor (A2)x3 ø1.4x2.8mm MDMechanism Figure 9-1 (B1)x2 Remove the solder joint Stop Washer (B2)x1 Drive Gear (B3)x1 Lift Motor (B4)x1 ø1.4x2.2mm Figure 9-2 Figure 9-3 (E1)x1 ø1.7x2.5mm Shaft Pickup Unit How to reinstall the optical pickup unit (See Fig. 9-5.) 1. Remove the screws (E1) x 1 pcs. 2. Remove the soldering joint (C2) x2 places of flex PWB, and remove the sled motor. How to remove the magnetic head (See Fig. 9-4.) 1. Remove the screw (D1) x 2 pc. 2. Remove the screw (D2) x1 which connects the magnetic head to the head relay flex PWB, and remove the soldering joint (D3) x2 pcs. Note: Mount carefully so as not to damage the magnetic head. (D1)x2 Ø1.4x1.8mm (D1)x1 Ø1.4x1.5mm Pickup Unit Magnetic Head Solder joint (D3)x2 Figure 9-4 How to remove the lift motor (See Fig. 9-2.) 1. Remove the solder joint (B1) x 2 of slide motor lead wire. 2. Remove the stop washer (B2) x 1 pc., and remove the drive gear (B3) x 1 PC. 3. Remove the screw (B4) x 1, and remove the lift motor. Note: Take care so that the motor gear is not damaged. (If the gear is damaged, noise is raised in search mode.) How to remove the sled motor (See Fig. 9-3.) 1. Remove the solder joint (C1) x 2 of slide motor lead wire. 2. Remove the screw (C2) x 2, and remove the sled motor. Note: Take care so that the motor gear is not damaged. (If the gear is damaged, noise is raised in search mode.) (C1)x2 ø1.4x1.2mm Sled Motor Washer x2 (C2)x2 Mecha Flexible PWB solder joint

1 High reflection disc MMD-110 (TEAC Test MD) 88GMMD-110 2 Lowreflection disc MMD-212 (TEAC Test MD) 88GMMD-212 3 Low reflection disc Recording minidisc UDSKM0001AFZZ ADJUSTMENT Test disc MD adjustment needs two types of disc, namely recording disc (low reflection disc) and playback-only disc (high reflection disc). Type Test disc Parts No. Note: Use the low reflection disc on which music has been recorded. EEPROM version Destination Leaving the TEST mode (1) Press the STOP button in the TEST mode stop state or version indicating state or whole LCD lighting state. (2) EEPROM rewrite-enable area updating, adjustment error setting (so as to adjust all the items when the power supply is turned on in the normal mode) (3) Change to standby state Test Mode 1. AUTO 1 Mode • Perform preliminary automatic adjustment. • If the combination of mechanism and pickup PWB has been changed, be sure to start from AUTO1. 2. AUTO 2 Mode • Perform ATT (attenuator) automatic adjustment. • Perform continuous playback (error rate display, jump test) 3. MANUAL 1 Mode • Temperature is displayed. (Updating in real time) • Seeing the displayed adjustment value, perform preliminary manual adjustment. (Error rate indication, jump test) 4. MANUAL 2 Mode • Temperature is displayed. (Updating in real time) • Seeing the displayed adjustment value perform manfully the preliminary adjustment. (Error rate indication, jump test) • Continuous playback is performed (error rate display, jump test). 5. RESULT 1 Mode • The value adjusted in AUTO1 or MANUAL1 is indicated. • (Execution in servo "OFF" state"). 6. RESULT 2 Mode • The value adjusted in AUTO 2 or MANUAL 2 is indicated. • Adjustment value is changed manually. (error rate display, jump test). 7. TEST-PLAY Mode • Continuous playback from the specified address is performed. • 1 line, 10 lines or 400 lines manual jump is performed. • C1 error rate display (pit section), ADIP error rate display (groove section) • The temperature correction is performed only when servo start is performed, but the posture correction is not performed duringcontinuous playback. Microcomputer version Entering the TEST mode 1. Setting at port (in standby state, disc-free state or power nonconnected state) (1) Set the port as follows. TEST1 : "Low" TEST0 : "High" (2) Press the PLAY button in the standby state (it is allowed to insert the disc or to connect the power supply). (3) Test Mode STOP [ _ T E S T _ ] 2. Setting by special button operation (in standby state) (1) Holding down the DISP button and ENTER button, press the PLAY button. (2) Normal mode setting initialization (BASS setting, VOL setting, etc.) (3) Indication of microcomputer version for one second [ ] (4) Whole LCD lighting for 2 seconds (5) Test Mode STOP [ _ T E S T _ ] *When the PLAY button is pressed during indication (3) and (4), the process proceeds to (5). 8. TEST-REC Mode • Continuous record from the specified address is performed. • Change of record laser output(servo gain is also changed according to laser output). • The temperature correction is performed only when servo start is performed, but the posture correction is not performed during continuous recording. 9. NORMAL Mode • The mode is changed from the TEST mode to the normal mode without adjustment. • In the normal mode the internal operation mode, memory capacity, etc. areindicated. • In the normal mode both temperature correction and posture correction are perfomed. 10. DIGITAL INPUT mode • Digital input information is displayed. 11. ERROR INFORMATION • Error information is displayed. Mode • Error information is initialized 12. E2-PROM Mode • Factors of digital servo are changed manually. (Each servo is turned on individually.) • Cut-off frequency of BASS1, BASS2 and BASS3 is selected manually. • Temperature detection terminal voltage is measured, and the reference value is set. • Defaults are selected and set. • Setting of EEPROM protect area is updated. (In case of protect releasing) 13. INNER Mode • Determine the position where the INNER switch is turned on. (only high reflection disc). • The temperature correction is performed only when servo start is performed, but the posture correction is not performed. Type Parts No. Price Code 1 Flat Cable for servicing 16Pin QCNWK0110AFZZ 2 Extension Connector for Service 16Pin RUNTK0460AFZZ Extension Cable (See Fig.10) Figure 10 Mecha Flexible PWB 16 pin 16 PIn CN601 QCNWK0110AFZZ 16pin Flat Cable RUNTK0460AFZZ Extension PWB for servicing 16pin PWB side

1. AUTO1 Mode • When the STOP button is pressed while the AUTO1 menu appears or during automatic adjustment, the mode changes to the TEST mode stop state. At this time the adjustment value is not output. • Be sure to adjust, using the specified disc MMD-212. At this time release the EEPROM (IC402) protection. (Refer to EEPROM write procedure.) • Adjustment NG; Adjustment item out of range, focus ON failure, and adjustment error • When the PLAY button is pressed while ADJ. OK is displayed, AUTO2 is executed. Operation in each TEST mode 2. AUTO2 Mode • When the STOP button is pressed while the AUTO2 menu appears or during automatic adjustment, the mode changes to the TEST mode stop state. At this time the adjustment value is not output. • Adjustment NG; Adjustment item out of range, and adjustment error 3. MANUAL1 Mode • Adjustment item to be made in AUTO1 mode is performed manually. • When the VOL UP button is pressed during adjustment, the setting increases, and the new setting is output. • If the VOL DOWN button is pressed during adjustment, the setting decreases and the new setting is output. • If the VOLUP/DOWN button is held down, the setting changes continuously with 100 ms cycle. • If the setting is within the allowable range, the RANDOM display lights. • When the STOP button is pressed during MANUAL1 MENU or measurement or adjustment, the state is changed to the TEST mode stop state. 4. MANUAL2 Mode • Adjustment item to be made in AUTO2 mode is performed manually. • When the VOL UP button is pressed during adjustment, the setting increases, and the new setting is output. • If the VOL DOWN button is pressed during adjustment, the setting decreases and the new setting is output. • If the VOLUP/DOWN button is held down, the setting changes continuously with 100 ms cycle. • If the setting is within the allowable range, the RANDOM display lights. • When the STOP button is pressed during MANUAL2 MENU or measurement or adjustment, the state is changed to the TEST mode stop state. • When the PLAY button is pressed in B-ATT set state, the mode is changed to the continuous playback mode. • As for operation during continuous playback refer to "TEST-PLAY mode explanation". 5. RESULT1 Mode 6. RESULT2 Mode • The measurement value and set value of adjustment items for AUTO1 and MANUAL 1 are displayed. • If the VOL UP button is pressed during setting indication, the setting increases. If the VOL DOWN button is pressed, the setting reduces. And then the new setting is stored in the RAM. • When the VOL UP/DOWN button is held down, the setting changes continuously, one cycle being 100 ms. • If the STOP button is pressed during RESULT1 menu or measurement value indication or set value indication, the state is changed to the TEST mode STOOP state. • The measurement value and set value of adjustment items for AUTO2 and MANUAL 2 are displayed. • If the VOL UP button is pressed during setting indication, the setting increases. If the VOL DOWN button is pressed, the setting reduces. And then the new setting is stored in the RAM. • When the VOL UP/DOWN button is held down, the setting changes continuously, one cycle being 100 ms. • If the STOP button is pressed during RESULT2 menu or measurement value indication or set value indication, the state is changed to the TEST mode STOOP state. 7. TEST-PLAY Mode •When the STOP button is pressed while the TEST-PLAY menu appears, or in TEST-PLAY or continuous playback mode, the mode changes to the TEST mode stop state. • When the PLAY button is pressed while the TEST-PLAY menu appears,continuous playback is initiated from the current pickup position. • Whenever the DISP button is pressed in the TEST-PLAY mode, the address changes as follows. 0050 — 03C0 — 0700 — 08A0 — 0050 — • Whenever the BASS key is pressed in the TEST-PLAY mode, the digit which is changed by the SKIP UP/DOWN button changes as follows. 0050 — 0050 — 0050 — 0050 — 0050 — • When the SKIP UP button is pressed in the TEST-PLAY mode, the digit of address specified by the BASS button is set to +1h. (0 to F) • When the SKIP DOWN button is pressed in the TEST-PLAY mode, the digit of address specified by the BASS button is set to -1h. (0 to F) * When the SKIP UP/DOWN button is held down, the setting changes continuously, one cycle being 100 ms. • When the BASS button is pressed in the continuous playback mode, the number of jump lines changes as follows. 1 — 10 — 400 — 1 * After the number of jump lines is indicated for one second, the address indication is restored. [ T R _ ] • When the SKIP UP button is pressed in the continuous playback mode, the specified number of lines is jumped in the FWD direction. • When the SKIP DOWN button is pressed in the continuous playback mode, the specified number of lines is jumped in the REV direction. * When the SKIP UP/DOWN button is held down, jump is repeated every approx. 100 ms.

• When the STOP button is pressed while the TEST-REC menu appears, or in the TEST-REC mode or continuous record mode, the mode changes to the TEST mode stop state. • When the PLAY button is pressed while the TEST-REC menu appears, the continuous record is initiated from the current pickup position. • Whenever the DISP button is pressed in the TEST-REC mode, the address changes as follows. 0050 — 03C0 — 0700 — 08A0 — 0050 — • Whenever the BASS button is pressed in the TEST-REC mode, the digit which is changed by the SKIP UP/DOWN button changes as follows. 0050 — 0050 — 0050 — 0050 — 0050 — • When the SKIP UP button s pressed in the TEST-REC mode, the digit of address specified by the BASS button is set to +1h.(0 to F) • When the SKIP DOWN button is pressed in the TEST-REC mode, the digit of address specified by the BASS button is set to -1h. (0 to F) * When the SKIP UP/DOWN button is held down, the setting changes continuously, one cycle being 100 ms. • When the VOL UP/DOWN button is pressed in the TEST-REC mode or continuous record mode, the laser record power changes. (Servo gain changes also according to record power.) * After the laser record power is indicated for one second, the address indication is restored. [ R P W ] • : Address • : Laser power cord • Operation is disabled if the premastered disc or disc is in miserase-protected state. 8. TEST-REC Mode 9. NORMAL Mode • When the STOP button is pressed while the NORMAl menu appears, the mode changes to the TEST mode stop state. • Indication during operation Indication of memory capacity on main unit LCD [ ] + Level meter : Internal mode : Address (Cluster section) : Address (Sector section) • Selection of sound volume, BASS, etc. is possible (without indication) • Recording is also possible. 11. Error data display Mode • Reversing when SKIP DOWN button is pressed • When the STOP button is pressed while the error data indication menu appears or during error data indication, the mode changes to the TEST mode stop state. • Error data 0 is the latest error. • Error which occurred in the TEST mode is also stored in the memory. • When the DISP button is pressed while the error data indication menu appears, the error data is initialized. [ C L E A R _ ] • : Error Code 10. Digital input display Mode (Din Mon) • When the STOP button is pressed while the digital input indication menu appears or during digital input information indication, the mode changes to the TEST mode stop state. • In case of analog input or digital input unlocking the indication data is _. Explanation of error history code 12h : RF side FG, TG, and TCRS adjustment termination failure 13h : Adjustment servo retraction excessive retrial 17h : A, B, E, F, and TCRSO offset measurement value out of tolerable range 21h : Focus retraction completion allowable time-over 23h : Track search completion allowable time-over 32h : P-TOC read failure 42h : U-TOC read failure 44h : U-TOC write data write disabled/read check error 52h : SD write data write disabled 71h : Pickup position initialization time-over •Whenever the DISP button is pressed in the continuous playback mode, the indication changes as follows. * Pit section Continuous playback (SUBQ address indication) [ S Q ] | Continuous playback (C1 error indication) [ C E ] | Continuous playback (SUBQ address indication) [ S Q ] * Groove section Continuous playback (ADIP address indication) [ A P ] | Continuous playback (C1 error indication) [ C E ] | Continuous playback (ADIP error indication) [ A E ] | Continuous playback (ADIP address indication) [ A P ]

12. INNER Mode • when the STOP button is pressed on the INNER menu (SQ______ ), the state is changed to the TEST mode STOP state. • : Address 72h : EEPROM data read check sum error 73h : Record head drive disabled (by EJECT lever) 82h : Power overvoltage detection 91h : Ambient temperature is higher that the allowable temperature. (1) Replace E2-PROM. (2) Deprive E2-PROM of protection (connect the pins 8 and 6 of IC402). (3) Refer to the latest E2-PROM data list. (4) Press the Display/Lower-case Character button, Enter/Synchro button and Play/Pause button to start the test mode. (5) Version display [ V e r . ] E2-PROM version (C ~ Z) Microcomputer ROM version (6) The whole LCD lights. (7) Test mode stop state [ T E S T ] (8) Press the "BASS" button, and press twice the "SKIP DOWN" button. [ E E P R O M ] (9) Perform the operation to display "E2-PROM SETTING MODE CHART", compare the E2-PROM DATA LIST with the display, and set according to the E2-PROM DATA LIST with the VOL UP or VOL DOWN key. (10) Set the temperature reference. (Refer to the Temperature Reference Setting Method.) (11) Set according to the E2-PROM DATA LIST. (12) Press the Stop button. [ T E S T ] (13) Press the Stop button. (14) After data is written in E2-PROM, turn off power . (15) Restore protection of E2-PROM (Disconnect connection made in Step (2) above). E2-PROM (IC402) writing procedure 1. Procedure to replace E2-PROM and write initial value of microcomputer in E2-PROM 2. Temperature reference setting method [1] Measurement, calculation and setting procedure (1) Set the TEST mode. • Set TEST 1, 0 = '01', and turn on power (or set PLAY ON in standby state). (2) Start the EEPROM mode 'Temp' menu. • In the TEST mode STOP state, press the keys as follows: BASS, SKIP-DOWN x 2 times, PLAY, SKIP-DOWN x 4 times, and PLAY in this order. • 'TM$$%%' is displayed. ($$= Temperature code, %% = Temperature reference) (3) Once press SKIP-UP, and determine the displayed microcomputer TEMP input AD value. • 'TPin##' is displayed. (## = TEMP input AD value) (4) At the ambient temperature, determine the temperature corrected value from the temperature measurement value correction table. (5) Determine the temperature reference, using the following formula. • Temperature reference = Microcomputer TEMP input AD value + Temperature corrected value • An example: Environmental temperature is 22°C and set voltage is 1.25V.

Ambient temperature Temperature correction -5oC ~ +9oC 08h + 0.5oC +6oC ~ +21oC 07h + 12.5oC +17oC ~ +32oC 06h + 23.6oC +29oC ~ +44oC 05h + 35.0oC Center temperature [3] Power IC VREF feed control output • Test/R-ROM write power input *Meaning of values • Temperature reference = Value to be predicted to be measured by the microcomputer at reference temperature (+23.6oC) • Temperature correction = Value to convert to measurement value at reference temperature (+23.6¯C) *Determining the temperature correction value • Temperature detection characteristics formula Ambient temperature (oC) = (-2.876 x TEMP input AD value) + 463 Hence, TEMP input AD value = (463 - Ambient temperature)/2.876 • The reference temperature (+23.6oC) is taken as a reference. (it is taken as '0'). Whenever the input AD value changes by '1', temperature is determined. For temperature correction, the input AD value is +/- inverted. Ambient temperature Temperature correction +14oC ~ +16oC - 03h + 15.0oC +17oC ~ +19oC - 02h + 17.8oC +20oC ~ +22oC - 01h + 20.7oC +23oC ~ +25oC ± 00h + 23.6oC +26oC ~ +27oC + 01h + 26.5oC +28oC ~ +30oC + 02h + 29.4oC [2] Temperature measurement value correction table Center temperature

E2-PROM DATA LIST TEMP setting Item display Set values T M _ _ Calculate values Sled setting Item display Set values S L G _ 9 4 H S L 2 _ 3 0 H S L M _ 4 F H S L V _ 3 6 H S K k _ 4 3 H S K t _ 4 0 H S K m _ 4 3 H EQ. SET setting Item display Set values H Q 1 _ 9 0 H H Q 2 _ 9 0 H H S G _ 1 1 H H S O _ F D H L Q 1 _ 9 0 H L Q 2 _ 9 0 H L S G _ 1 1 H L S O _ 0 0 H G Q 1 _ 9 8 H G Q 2 _ 8 4 H G S G _ 1 1 H G S O _ 0 0 H G Q R _ 0 0 H ADJ. SET setting Item display Set values C O K _ A 0 H F A T _ C 0 H T A T _ 3 F H C A T _ 2 0 H F A B _ 0 0 H Control setting Item display Set values C T 0 _ 4 8 H C T 1 _ E 0 H P W L _ 0 0 H R C 0 _ C 0 H R C 1 _ F E H S Y C _ A 6 H D R 1 _ A 0 H D R 2 _ A 6 H I N 1 _ D 4 H I N 2 _ 6 7 H C T R _ 6 D H C T 2 _ 1 4 H C T 3 _ 0 3 H C T 4 _ 6 4 H C T 5 _ 7 4 H C T 6 _ 0 8 H C T 7 _ 0 0 H S P M _ 0 0 H M S L _ 8 0 H R S L _ 0 0 H BASS setting Item display Set values B S 1 _ 0 2 H B S 2 _ A 4 H B S 3 _ C 4 H Item display Set values F G _ _ 6 3 H F F 1 _ 7 0 H F F 2 _ F 0 H F Z H _ E D H F L n _ 0 9 H D J G _ 1 4 H F R V _ 0 0 H F P f _ 8 8 H F L V _ 1 9 H W T f _ 2 0 H F S S _ 0 2 H Fucus setting Tracking setting Item display Set values T G _ _ 2 6 H T F 1 _ 7 0 H T F 2 _ E 0 H T F S _ 0 0 H T B o _ 2 B H T B t _ 1 7 H T K o _ 2 B H T K t _ 1 9 H T D o _ 6 7 H T D t _ 2 A H S C o _ 0 0 H S C t _ 4 0 H S C m _ 5 3 H D B O _ 0 0 H C L p _ 1 2 H C L r _ 2 4 H W T m _ E 0 H Item display Set values S P G _ 1 4 H S P i _ A A H S P m _ 7 9 H S P o _ 4 F H S P 1 _ 1 0 H S P 2 _ 6 0 H S P 3 _ F 2 H S P 4 _ F 2 H S P 5 _ 1 0 H S P D _ 6 1 H S P R _ C 4 H Spindle setting

: Test Mode STOP : Pre-autoadjustment menu : ATT autoadjustment menu : Pre-manual adjustment menu : ATT manual adjustment menu : Preadjustment value check menu : ATT adjustment value check menu : Continuous record menu (record/playback machine only) : Test mode normal playback menu : Error history display menu : EEPROM setting menu : INNER switch position measurement menu BASS T E S T Slide external periphery move Slide internal periphery move Tset Mode Menu Test Mode Change Chart A U T O 1 A U T O 2 SKIP UP SKIP DOWN SKIP DOWN M A N U 1 SKIP UP SKIP DOWN M A N U 2 SKIP UP SKIP DOWN R S L T 1 SKIP UP SKIP DOWN R S L T 2 SKIP UP SKIP DOWN T R E C SKIP UP SKIP DOWN : Continuous playback menu T P L A Y SKIP UP SKIP DOWN N O R M A L SKIP UP SKIP DOWN E D A T A SKIP UP SKIP DOWN : Digital input signal monitor menu (record/playback machine only) D i n M o n SKIP UP SKIP DOWN E E P R O M SKIP UP SKIP DOWN I N N E R SKIP UP SKIP UP SKIP DOWN SKIP DOWN SKIP UP * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. : Preautomatic Adjustment menu : Preadjustment error (adjustment value output) : During preadjustment adjustment Adjustment error Normal end : Preadjustment normal end (adjustment value output) : During ATT automatic adjustment PLAY PLAY A U T O 1 Preautomatic Adjustment A D J . O K A D J . N G A T 2 A T 1 * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * " " represent the adjustment number as follows. 0 0 : Innermost periphery move 0 2 : ABEF offset tentative measurement 0 4 : RF side focus gain coarse adjustment 0 5 : Focus ATT tentative setting 0 6 : RF side bit section tracking gain adjustment 0 7 : COUT level setting for pit section adjustment 0 8 : External periphery move 0 9 : RF side groove section tracking gain adjustment 1 0 : COUT level setting for groove section adjustment 1 1 : RF side TCRS gain adjustment 1 2 : Tracking ATT initial setting 1 3 : RF side focus gain minor adjustment 1 4 : Focus ATT initial setting 1 5 : S gain "High" ABEF offset measurement 1 6 : TCRS offset measurement 1 7 : S gain "Low" ABEF offset measurement

: ATT Autoadjustment menu : ATT adjustment error (adjustment value output) : During ATT autoadjustment Adjustment error Normal end : ATT adjustment normal end (adjustment value output) : Continuous playback (high reflection) : Continuous playback (low reflection) PLAY PLAY A U T O 2 ATT Autoadjustment A D J . O K A D J . N G S Q # # # # A P # # # # A T 2 * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * " " represent the adjustment number as follows. 0 0 : Innermost periphery move 0 3 : Pit section tracking ATT setting 0 4 : Pit section focus ATT setting 0 6 : External periphery move (low reflection only) 0 7 : TCRS ATT setting (low reflection only) 0 8 : Groove section tracking ATT setting (low reflection only) 0 9 : Groove section focus ATT setting (low reflection only) : Pre-Manual Adjustment menu : Temperature code display $ $ : Temperature code : A signal offset (AINO) tentative measurement : Measurement value : B signal offset (BINO) tentative measurement : Measurement value : E signal offset (EINO) tentative measurement : Measurement value : F signal offset (FINO) tentative measurement : Measurement value : Laser On (Play Power) : RF side focus gain coarse adjustment : Gain setting : A-ATT (focus) tentative setting : ATT setting : B-ATT (focus) tentative setting : ATT setting : RF side pit section tracking gain adjustment : Gain setting : Pit section adjustment COUT level setting : COUT level setting RF side groove section tracking gain adjustment : Gain setting : Groove section adjustment COUT level setting : COUT level setting : RF side TCRS gain adjustment : Gain setting : E-ATT (tracking) initial setting : ATT setting : F-ATT (tracking) initial setting : ATT setting PLAY M A N U 1 Pre-Manual Adjustment T M P $ $ A h SKIP UP SKIP DOWN B h SKIP UP SKIP DOWN E h SKIP UP SKIP DOWN F h SKIP UP SKIP DOWN L O N P SKIP UP SKIP DOWN R F g SKIP UP SKIP DOWN S a SKIP UP SKIP DOWN S b SKIP UP SKIP DOWN P T G SKIP UP SKIP DOWN P C H SKIP UP SKIP DOWN G T G SKIP UP SKIP DOWN G C H SKIP UP SKIP DOWN R C G SKIP UP SKIP DOWN S E SKIP UP SKIP DOWN S F SKIP UP SKIP DOWN Continued to the next page SKIP UP SKIP DOWN

: RF side focus gain minor adjustment : Gain setting : A-ATT (focus) initial setting : ATT setting : B-ATT (focus) initial setting : ATT setting : S gain "High" A signal offset (AINO) measurement : Measurement value : S gain "High" B signal offset (BINO) measurement : Measurement value : S gain "High" E signal offset (EINO) measurement : Measurement value : S gain "High" F signal offset (FINO) measurement : Measurement value TCRS signal offset (TCRSO) measurement : ATT setting : S gain "Low" A signal offset (AINO) measurement : Measurement value : S gain "Low" B signal offset (BINO) measurement : Measurement value : S gain "Low" E signal offset (EINO) measurement : Measurement value : S gain "Low" F signal offset (FINO) measurement : Measurement value Continued from the preceding page R F G SKIP UP SKIP DOWN S A SKIP UP SKIP DOWN S B SKIP UP SKIP DOWN A H SKIP UP SKIP DOWN B H SKIP UP SKIP DOWN E H SKIP UP SKIP DOWN F H SKIP UP SKIP DOWN T H SKIP UP SKIP DOWN A L SKIP UP SKIP DOWN B L SKIP UP SKIP DOWN E L SKIP UP SKIP DOWN F L SKIP UP SKIP DOWN P-MODE P-MODE * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. (In case of RF side gain setting change does not occur since there is only one digit.) • 2-digit setting 1st digit (initial value) 2nd value • 3-rd digit setting 1st digit (initial value) 2nd value 3rd digit P-MODE P-MODE P-MODE * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. L O N P L O N R * In laser ON state (without disc) the laser power is changed as follows when the [BASS] key is pressed. L O N M Play power Max. power BASS BASS BASS Record power : RF side focus gain coarse adjustment : A-ATT (focus) tentative setting : B-ATT (focus) tentative setting : ABMXO measurement value display "REPEAT" mark lighting R F g S a S b A B DISP DISP * In the setting display sate the value of selected digit changes in the range of "0h to Fh" when [VOL UP/DOWN] key is pressed. However, the RF side gain setting changed in the range of "0h to 6h". * When the [DISP] key is pressed, the display changes as follows. • ABMAXO Measurement value : RF side TCRS gain adjustment : TCRSMIO measurement value display "REPEAT" mark lighting R C G T C DISP DISP • TCRSMIO Measurement value : E-ATT (tracking) initial setting : LPFEINO measurement value display "REPEAT" mark lighting : EFMIO measurement value display "REPEAT", "1" mark lighting S E e i E F DISP DISP DISP • LPFEINO/EFMIO Measurement value : F-ATT (tracking) initial setting : LPFEINO measurement value display "REPEAT" mark lighting : EFMIO measurement value display "REPEAT", "1" mark lighting S F f i E F DISP DISP DISP • LPFEINO/EFMIO Measurement value : RF side focus gain coarse adjustment : A-ATT (focus) initial setting : B-ATT (focus) initial setting : LPFABO measurement value display "REPEAT" mark lighting R F G S A S B a b DISP DISP • LPFABO Measurement value : RF side pit section tracking gain adjustment : Pit section adjustment COUT level setting : RF side groove section tracking gain adjustment : Groove section adjustment COUT level setting : LPFEFO measurement value display "REPEAT" mark lighting P T G P C H G T G G C H e f DISP DISP • LPFEFO Measurement value

: Temperature code displayATT manual adjustment menu : Temperature code display $ $ : Temperature code : Laser ON (Play Power) : Pit section E-ATT (tracking) setting : ATT setting : Pit section E-ATT (tracking) setting : ATT setting : High reflection: A-ATT (focus) setting : Low reflection: A-ATT (focus) setting : ATT setting : TCRS ATT setting : ATT setting :Groove section E-ATT (tracking) setting : ATT setting :Groove section F-ATT (tracking) setting : ATT setting : Low reflection: A-ATT (focus) setting : ATT setting : Low reflection: B-ATT (focus) setting : ATT setting : High reflection pit section B-ATT (focus) setting : Low reflection pit section B-ATT (focus) setting : Low reflection groove section B-ATT (focus) setting : ATT setting Continuous playback (pit section) Continuous playback (groove section) # # # # : Address PLAY M A N U 2 ATT Manual Adjustment T M P $ $ L O N P L O N P L O N R SKIP UP SKIP DOWN P E SKIP UP SKIP DOWN P F SKIP UP SKIP DOWN H A L a SKIP UP SKIP DOWN : High reflection: B-ATT (focus) setting : Low reflection: B-ATT (focus) setting : ATT setting H B L b SKIP UP SKIP DOWN G C SKIP UP SKIP DOWN H B L b L B S Q # # # # A P # # # # PLAY P-MODE G E SKIP UP SKIP DOWN G F SKIP UP SKIP DOWN L A SKIP UP SKIP DOWN L B SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In B-ATT setting state, the continuous playback is started when the [PLAY] key is pressed. When in the continuous playback state the ATT manual adjustment B-ATT setting state is started when the [P-MODE] key is pressed in continuous playback state. * In laser ON state (without disc) the laser power is changed as follows if the [BASS] key is pressed (record/playback machine only). L O N M Play power Max. power BASS BASS BASS Record power P-MODE P-MODE P-MODE * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. 1st digit (initial value) 2nd value 3rd digit * In the specific setting display state the selection digit value changes in the range of "0h to Fh" when [VOL UP/DOWN] key is operated. * When the [DISP] key is pressed, the display changes as follows. : High reflection pit section A-ATT (focus) setting : High reflection pit section B-ATT (focus) setting : Low reflection pit section A-ATT (focus) setting : Low reflection pit section B-ATT (focus) setting : Low reflection groove section A-ATT (focus) setting : Low reflection groove section B-ATT (focus) setting : LPFABO measurement value display "REPEAT" mark lighting H A H B L a L b L A L B a b DISP DISP • LPFABO Measurement value : Pit section E-ATT (tracking) setting : Groove section E-ATT (tracking) setting : LPFEINO measurement value display "REPEAT" mark lighting : EFMIO measurement value display "REPEAT", "1" mark lighting P E G E e i E F DISP DISP DISP • LPFEINO/FEMIO Measurement value : Pit section F-ATT (tracking) setting : Groove section F-ATT (tracking) setting : LPFEINO measurement value display "REPEAT" mark lighting : EFMIO measurement value display "REPEAT", "1" mark lighting P F G F f i E F DISP DISP DISP • LPFEINO/FEMIO Measurement value : TCRS ATT setting : TCRSMIO measurement value display "REPEAT" mark lighting G C T C DISP DISP • TCRSMIO Measurement value

: B-ATT (focus) initial setting : E-ATT (tracking) initial setting : F-ATT (tracking) initial setting Continued from the preceding page S B SKIP UP SKIP DOWN S E SKIP UP SKIP DOWN S F SKIP UP SKIP DOWN P-MODE P-MODE * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. (For RF side gain setting only one digit is provided. Therefore change does not occur.) • 2-digit setting 1st digit (initial value) 2nd digit • 3-digit setting 1st digit (initial value) 2nd digit 3rd digit P-MODE P-MODE P-MODE * In the specific setting display state the value of selected digit changes in the range of "0h to Fh" when the [VOL UP/DOWN] key is pressed. However, the RF side gain setting changes in the range of "0h to 6h". : Pre-Adjustment Value Check menu : S gain "High" A signal offset measurement value (setting) : S gain "High" B signal offset measurement value (setting) : S gain "High" E signal offset measurement value (setting) : S gain "High" F signal offset measurement value (setting) : S gain "Low" A signal offset measurement value (setting) : S gain "Low" B signal offset measurement value (setting) : S gain "Low" E signal offset measurement value (setting) : S gain "Low" F signal offset measurement value (setting) : TCRS signal offset measurement value : RF side pit section tracking gain setting : RF side groove section tracking gain setting : RF side TCR gain setting : RF side focus gain setting : Pit section adjustment COUT level setting : Groove section adjustment COUT level setting : A-ATT (focus) initial setting PLAY R S L T 1 Pre-Adjustment Value Check A H B H SKIP UP SKIP DOWN E H SKIP UP SKIP DOWN F H SKIP UP SKIP DOWN A L SKIP UP SKIP DOWN B L SKIP UP SKIP DOWN E L SKIP UP SKIP DOWN F L SKIP UP SKIP DOWN T H SKIP UP SKIP DOWN P T G SKIP UP SKIP DOWN G T G SKIP UP SKIP DOWN R C G SKIP UP SKIP DOWN R F G SKIP UP SKIP DOWN P C H SKIP UP SKIP DOWN G C H SKIP UP SKIP DOWN S A SKIP UP SKIP DOWN Continued to the next page SKIP UP SKIP DOWN

: ATT Setting Check : Pit section E-ATT (tracking) setting : Pit section F-ATT (tracking) setting : Groove section E-ATT (tracking) setting : Groove section F-ATT (tracking) setting : High-reflection A-ATT (focus) setting : High-reflection B-ATT (focus) setting : Low-reflection A-ATT (focus) setting : Low-reflection B-ATT (focus) setting : TCRS-ATT setting PLAY R S L T 2 ATT Setting Check P E P F SKIP UP SKIP DOWN G E SKIP UP SKIP DOWN G F SKIP UP SKIP DOWN H A SKIP UP SKIP DOWN H B SKIP UP SKIP DOWN L A SKIP UP SKIP DOWN L B SKIP UP SKIP DOWN G C SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. • 3-digit setting 1st digit (initial value) 2nd digit 3rd digit P-MODE P-MODE P-MODE * In the specific setting display state the value of selection digit changes in the range of "0h to Fh" when the [VOL UP/DOWN] key is pressed. : Continuous playback menu : Continuous playback (pit section) : Continuous playback (groove section) # # # # : Address : Continuous playback (pit section) : Continuous playback (groove section) # # # # : Address PLAY T P L A Y Continuous Playback S Q # # # # A P # # # # : Continuous playback (pit section) : Continuous playback (groove section) # # # # : Address : High reflection pit section B-ATT (focus) setting : High reflection groovesection B-ATT (focus) setting : ATT setting P-MODE S Q # # # # A P # # # # H B L B * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the start address set state the start address changes as follows when the [DISP] key is pressed. 0 0 5 0 H (initial value) 0 3 C 0 H 0 7 0 0 H 0 8 A 0 H A d 0 0 5 0 A d 0 3 C 0 DISP DISP A d 0 7 9 0 DISP DISP A d 0 8 A 0 * In the start address setting state the start address change digit changes when the [BASS] key is pressed. 1st digit (initial value) 2nd digit 3rd digit A d 0 0 5 0 A d 0 0 5 0 BASS BASS A d 0 0 5 0 BASS * In the continuous playback state the number of jump lines changes as follows shown the [BASS] key is pressed. 1 (initial value) 10 400 1 T R 1 0 T R BASS BASS 4 0 0 T R BASS • Continuous playback from current pickup position : Continuous playback menu : Start address setting DISP T P L A Y A d 0 0 5 0 PLAY S Q # # # # A P # # # # • Continuous playback from any address * In the start address set state the value of selection digit changes in the range of "0h to Fh" when the [SKIP UP/DOWN" key is pressed. * In the continuous playback state the state is changed to ATT manual adjustment B-ATT setting state when the [P-MODE] key is pressed. * In the continuous playback state, jump ocurs in the specified number external periphery direction. If the key is held down, jump occurs continuously with 100 ms period.

: Continuous record menu PLAY T R E C Continuous Rrecord A P # # # # * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the start address set state the start address changes as follows when the [DISP] key is pressed. • Continuous record from the current pickup position : Continuous record menu : Start address setting : Continuous record # # # #: Address : Continuous record # # # #: Address PLAY T R E C A d 0 0 5 0 PLAY A P # # # # • Continuous record playback from any address A d 0 0 5 0 0 0 5 0 H (initial value) 0 3 C 0 H 0 7 0 0 H 0 8 A 0 H A d 0 3 c 0 DISP A d 0 7 0 0 DISP DISP DISP A d 0 8 A 0 * In the start address setting state the start address change digit changes when the [BASS] key is pressed. * In the start address set state the value of selection digit changes in the range of 0h to Fh wh en the [SKIP UP/DOWN] key is pressed. * In the continuous record state and start address set state the record laser power changes in t he range of "0h to Fh" when the [VOL UP/DOWN] key is pressed. A d 0 0 5 0 1st digit (initial value) 2nd digit 3rd digit A d 0 0 5 0 BASS A d 0 0 5 0 BASS BASS : INNER switch position measurement menu : Continuous playback (pit section) # # # # : Address PLAY I N N E R Inner Switch Position Measurement S Q # # # # * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. : TEST mode normal playback menu : Continuous playback @@@@@: Mode and address display PLAY N O R M A L Test Mode Normal Playback @ @ @ @ @ * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. : Digital input single monitor menu : FS code, C bit data display : Address : Control code : Category code PLAY D i n M o n Digital Input Signal Monitor C : U bit 1 data display : TNO : INDEX SKIP UP U 1 SKIP UP SKIP DOWN SKIP DOWN : U bit 2 data display : TIME (min.) : TIME (sec.) U 2 * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set.

: Error history display menu : Error history 0 display § § : Error code : Error history 1 display § § : Error code : Error history 2 display § § : Error code : Error history 3 display § § : Error code : Error history 4 display § § : Error code : Error history 5 display § § : Error code : Error history 6 display § § : Error code : Error history 7 display § § : Error code : Error history 8 display § § : Error code : Error history 9 display § § : Error code PLAY E D A T A Error History Display E 0 § § E 1 § § : Error history display menu : Error history clear PLAY E D A T A C L E A R SKIP UP SKIP DOWN E 2 § § SKIP UP SKIP DOWN E 3 § § SKIP UP SKIP DOWN E 4 § § SKIP UP SKIP DOWN E 5 § § SKIP UP SKIP DOWN E 6 § § SKIP UP SKIP DOWN E 7 § § SKIP UP SKIP DOWN E 8 § § SKIP UP SKIP DOWN E 9 § § SKIP UP SKIP DOWN • Error history clear • Error history display * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. : EEPROM setting menu : Focus setting menu : Spin setting menu : Tracking setting menu : Sled setting menu : BASS setting menu : TEMP setting menu : Adjustment setting menu : Digital EQ setting menu : Control setting menu PLAY E E P R O M EEPROM Setting F o c u s S p i n SKIP UP SKIP DOWN T r a c k SKIP UP SKIP DOWN S l e d SKIP UP SKIP DOWN B a s s SKIP UP SKIP DOWN T e m p SKIP UP SKIP DOWN A D J S E T SKIP UP SKIP DOWN D E Q S E T SKIP UP SKIP DOWN C T R L SKIP UP SKIP DOWN SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set.

: Focus setting menu : Focus system loop filter gain constant setting : setting : Focus system loop filter f-characteristics constant 1 setting : setting Focus system loop filter f-characteristics constant 2 setting : setting : FZC detection hysteresis level setting : setting : FOK generation comparison level setting (normal) : setting : DISC-ID judgment high-reflection lower-limit level : setting : Focus-related other settings : setting : FOK generation LPF factor setting (when focus "ON") : setting : Focus servo amptitude : setting : Auto-focus retraction waiting time setting : setting : Focus search inclination : setting PLAY F o c u s Focus Setting F G F F 1 SKIP UP SKIP DOWN F F 2 SKIP UP SKIP DOWN F Z H SKIP UP SKIP DOWN F L n SKIP UP SKIP DOWN D J G SKIP UP SKIP DOWN F R V SKIP UP SKIP DOWN F P f SKIP UP SKIP DOWN F L V SKIP UP SKIP DOWN W T f SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific state pressing the [DISP] key causes change to "focus setting menu". * In specific state the setting changed in the range of "00h to FFh" when the [VOL UP/DOWN" key is pressed. (The upper limit varies depending on the items) F F S SKIP UP SKIP DOWN : Spin setting menu : Spin system loop filter gain constant setting (until servo is turned on) : setting : Spin system loop filter again constant setting (after servo is turned on, internal periphery) : setting : Spin system loop filter gain constant setting (after servo is turned on, center) : setting : Spin system loop filter gain constant setting (after servo is turned on, externalperiphery) : setting : Spin system loop filter f-chracteristics constant 1 setting : setting Spin system loop filter f-chracteristics constant 2 setting : setting Spin system loop filter f-chracteristics constant 3 setting : setting Spin system loop filter f-chracteristics constant 4setting : setting Spin system loop filter f-chracteristics constant 5 setting : setting : Spin drive PWM duty limiter setting : setting : Spin-related other settings : setting PLAY S p i n Spin Setting S P G S P i SKIP UP SKIP DOWN S P m SKIP UP SKIP DOWN S P o SKIP UP SKIP DOWN S P 1 SKIP UP SKIP DOWN S P 2 SKIP UP SKIP DOWN S P 3 SKIP UP SKIP DOWN S P 4 SKIP UP SKIP DOWN S P 5 SKIP UP SKIP DOWN S P D SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific state pressing the [DISP] key causes change to "focus setting menu". * In specific state the setting changed in the range of "00h to FFh" when the [VOL UP/DOWN" key is pressed. (The upper limit varies depending on the items) S P R SKIP UP SKIP DOWN

: Tracking setting menu : Tracking system loop filter gain constant setting (normal) : setting : Tracking system loop filter f-characteristics constant 1 setting (normal) : setting : Tracking system loop filter f-characteristics constant 2 setting (normal) : setting : Tracking system filter selection switch setting : setting : Tracking brake level setting (1 line jump) : setting : Tracking brake level setting (10 line jump) : setting : Tracking kick level setting (1 line jump) : setting : Tracking kick level setting (10 line jump) : setting : Tracking drive pulse width time setting (1 line jump) : setting : Tracking drive pulse width time setting (10 line jump) : setting : Tracking slip stop time setting (1 line jump) : setting : Tracking slip stop time setting (10 line jump) : setting : Tracking slip stop time setting (move) : setting : PWM output offset setting : setting : COUT generation comparison level setting (PLAY) : setting COUT generation comparison level setting (REC) : setting Auto-move waiting time setting : setting PLAY T r a c k Tracking setting T G T F 1 SKIP UP SKIP DOWN T F 2 SKIP UP SKIP DOWN T F S SKIP UP SKIP DOWN T B o SKIP UP SKIP DOWN T B t SKIP UP SKIP DOWN T K o SKIP UP SKIP DOWN T K t SKIP UP SKIP DOWN T D o SKIP UP SKIP DOWN T D t SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific state the setting changes in the range of "00h to FFh" when the [VOL UP/DOWN] key is pressed. (The upper limit varies depending on the items) S C o SKIP UP SKIP DOWN S C t SKIP UP SKIP DOWN S C m SKIP UP SKIP DOWN D B O SKIP UP SKIP DOWN C L p SKIP UP SKIP DOWN C L r SKIP UP SKIP DOWN W T m SKIP UP SKIP DOWN : Slide setting menu : Slide system loop filter gain constant setting : setting : Slide system filter specific constant 2 setting : setting : Slide drive PWM duty limiter setting : setting : Slide serve output dead zone level setting : setting : Slide kick pulse level setting (forced shift) : setting : Slide kick pulse level setting (for 10 lines jump auxiliary) : setting : Slide kick pulse level setting (move) : setting PLAY S l e d Slide Setting S L G S L 2 SKIP UP SKIP DOWN S L M SKIP UP SKIP DOWN S L V SKIP UP SKIP DOWN S K k SKIP UP SKIP DOWN S K t SKIP UP SKIP DOWN S K m SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific state the setting changes in the range of "00h to FFh" when the [VOL UP/DOWN] key is pressed. (The upper limit varies depending on the items) : BASS setting menu : BASS1 characteristics setting : setting : BASS2 characteristics setting : setting : BASS3 characteristics setting : setting PLAY B a s s BASS setting B S 1 B S 2 SKIP UP SKIP DOWN B S 3 SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific state the setting changes in the range of "00h to FFh" when the [VOL UP/DOWN] key is pressed. (The upper limit varies depending on the items)

: Temp setting menu : TEMP setting : setting § § : Temperature code : TEMP A/D input value : Measurement value PLAY T e m p TEMP Setting T M § § T p i n SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In the specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific state the setting changes in the range of "00h to FFh" when the [VOL UP/DOWN] key is pressed. : Adjustment setting menu : Adjustment COUT level reference value : setting : Focus ATT reference value : setting : Tracking ATT reference value : setting : TCRS ATT reference value : setting : Focus balance factor : setting PLAY A D J S E T Adjustment Setting C O K F A T SKIP UP SKIP DOWN T A T SKIP UP SKIP DOWN C A T SKIP UP SKIP DOWN F A B SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. 1st digit (initial value) 2nd digit P-MODE P-MODE * In the specific state the setting changes in the range of "0h to Fh" when the [VOL UP/DOWN" key is pressed. : Digital EQ setting menu : High-reflection pit section Digital EQ tap factor A, D : setting : High-reflection pit section Digital EQ tap factor B, C : setting : High-reflection pit section Autolevel slicer gain : setting : High-reflection pit section Autolevel slicer slice level offset : setting : Lows-reflection pit section Digital EQ tap factor A, D : setting : Low-reflection groove section digital EQ tap factor A, D : setting : Lows-reflection pit section Digital EQ tap factor B, C : setting : Low-reflection pit section Autolevel slicer gain : setting : Low-reflection pit section Autolevel slicer slice level offset : setting : Low-reflection groove section digital EQ tap factor B, C : setting : Low-reflection groove section Autolevel slicer gain : setting : Low-reflection groove section Autolevel slicer slice level offset : setting : Digital EQ-related other settings : setting PLAY D E Q S E T Digital EQ Setting H Q 1 H Q 2 SKIP UP SKIP DOWN H S G SKIP UP SKIP DOWN H S O SKIP UP SKIP DOWN L Q 1 SKIP UP SKIP DOWN L Q 2 SKIP UP SKIP DOWN L S G SKIP UP SKIP DOWN L S O SKIP UP SKIP DOWN G Q 1 SKIP UP SKIP DOWN G S O SKIP UP SKIP DOWN D Q R SKIP UP SKIP DOWN G Q 2 SKIP UP SKIP DOWN G S G SKIP UP SKIP DOWN * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. 1st digit (initial value) 2nd digit P-MODE P-MODE * In the specific state the setting changes in the range of "0h to Fh" when the [VOL UP/DOWN" key is pressed.

: Control setting menu : Play start SD number, EEPROM version : setting : REC superposition, EL existence/nonexistence, move start minimum number, high-speed jump over-run : setting : DC-IN existence/nonexistence judgment level, AC adapter judgment level, built-in battery full judgment level : setting : Recording bit distribution parameter 0 : setting : Recording bit distribution parameter 1 : setting : Syncro level selection : setting : Dry cell exhaustion detection level setting 1 : setting : Dry cell exhaustion detection level setting 2 : setting : Built-in battery exhaustion detection level setting 1 : setting : Built-in battery exhaustion detection level setting 2 : setting : Intermittent servo restart accumulation sector number setting : setting : Control setting 2 : setting : Control setting 3 : setting : Control setting 4 : setting : Control setting 5 : setting : Control setting 6 : setting PLAY C T R L Control Setting (record/playback machine) C T 0 C T 1 SKIP UP SKIP DOWN P W L SKIP UP SKIP DOWN R C 0 SKIP UP SKIP DOWN R C 1 SKIP UP SKIP DOWN S Y C SKIP UP SKIP DOWN D R 1 SKIP UP SKIP DOWN D R 2 SKIP UP SKIP DOWN I N 1 SKIP UP SKIP DOWN I N 2 SKIP UP SKIP DOWN I N R SKIP UP SKIP DOWN C T 2 SKIP UP SKIP DOWN C T 3 SKIP UP SKIP DOWN C T 4 SKIP UP SKIP DOWN C T 5 SKIP UP SKIP DOWN C T 6 SKIP UP SKIP DOWN Continued to the next page SKIP UP SKIP DOWN : Control setting 2 : setting : Special mode selection data (unprotect area) : setting : Monitor selection data (unprotect area) : setting : Control-related other setting data (unprotect area) : setting Continued from the preceding page C T 7 SKIP UP SKIP DOWN S P M SKIP UP SKIP DOWN M S L R S L * When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set. * In specific state pressing the [DISP] key causes change to "focus setting menu". * In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. 1st digit (initial value) 2nd digit P-MODE P-MODE * In the specific state the setting changes in the range of "0h to Fh" when the [VOL UP/DOWN" key is pressed.

SW401 EJECT OFF—ON SW402 HOLD OFF—ON SW901 DISC IN OFF—ON SW902 DISC PROTECT OFF—ON NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad. As to electro- lytic capacitor, the expression “capacitance/withstand volt- age” is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chas- sis with no signal given. • Parts marked with “ ” ( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. POSITION REF. NO DESCRIPTION Figure 28 TYPES OF TRANSISTORS AND DIODES 2SA1314 C 2SA2982 C FRONT VIEW (G) 1 (D) 2 (S) 3 SB0209CP DA221 1SS373 SB00703Q TOP VIEW TOP VIEW B (D) (3) E (G) (1) C (S) (2) TOP VIEW DTC144 TE 2SC4213 B

Figure 29 BLOCK DIAGRAM LASER HEAD LIFT MOTOR MOTOR DRIVER SPINDLE MOTOR SLED MOTOR SPINDLE MOTOR DRIVER (BA6965FV) VCC VS HEAD DRIVER VS VCC RF SIGNAL PROCESSOR (IR3R55) PICK COIL DRIVER VCC VM 4 M D-RAM (IC202) ENDEC ATRAC (LB37648B) SYSTEM MICROCOMPUTER E2-PROM DISPLAY UNIT OPERATION UNIT AD/DA CONVERTER POWER DRIVER 2.5V REGULATOR +2.8V -2.8V (IR3M09) VCC POWER DRIVER (IR3M09) 2.5V REGULATOR (ON/OFF) (IR3R54N) AUDIO AMP. VCC VEE (IR3R54N) AUDIO AMP. VCC VEE +6~8 DC IN RIPPLE FILTER DIGITAL INPUT OPTICAL INPUT UNIT LINE INPUT LINE OUT MIC IN HEAD PHONES 4.5V REGULATOR (ON/OFF) REMOTE CONTROL POWER SELECT N-ch MOS FET 3V DC/DCONVERTER BATTERY VOLTAGE REGULATOR CONSTANT CURRENT DRIVE RECHARGEABLE BATTERY OPIC POWER SELECT CHARGE DRIVER VCC +2.8 +2.5 F IC901 +2.5 (LB1638) IC651 +2.5 +2.2 +2.5 +2.5 +2.5 +2.5 +2.5 (74ACT02) IC351 IC101 IC601 IC201 IC401 +2.5 IC402 +2.8 IC501 +2.5P IC771 +2.8 IC841 IC821 +2.5 +2.5 IC875 IC701 +2.8V -2.8V IC703 +2.8V -2.8V J701 +4.5 J701 J702 Q721 IC702 J703 IC801,803,804 +1.8~5.5V IC871 3~5V (1.8~3.4V) IC800,805,Q801 (2.9~4.1V) J801 DC JACK (4~5.5V) PICK T

Figure 30 SCHEMATIC DIAGRAM (1/4) P30 P31 P32 NOTES ON SCHEMATIC DIAGRAM can be found on page 28. A B C D E F G H 1 2 3 4 5 6 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 14 13 12 11 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 27 26 28 29 30 31 32 33 34 35 36 10 9 8 7 6 5 4 3 2 1 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 26 27 28 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 100 50 49 48 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 25 26 27 28 29 30 31 32 33 34 35 36 48 47 46 45 44 43 42 41 40 39 38 37 12 13 14 15 16 17 18 19 20 21 22 23 24 25 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 41 40 42 43 44 45 46 47 48 49 50 51 52 53 54 51 52 53 54 55 56 57 58 59 60 61 62 63 64 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 MAIN PWB-A1 1 16 SW902 DISC PROTECT HEAD PH901 COM W U V – + – + M M M PWB FLEXIBLE PICKUP UNIT FLEXIBLE PWB RF1 RF3 RF4 RF2 F– T+ F+ T– F E AGND LDVAR DGND DGND VCC CVCC COM LDON A B MP/R VCC OPIC CIN MCCK EFMO SPDRR GND VCC GND CSL2 CSL1 CST COM WIN VIN UIN UOUT RF WOUT NC VCC FG BRK– BRK+ STBY RIB VOUT VM DISCIN DISCPR INNSW PDCNT SPDRF SLDRF SLDRR DCNT1 VG VC LG GND VD3 FO3 RO1 PGND RO3 VD3 VD4 PGND RO4 RO2 RI4 FI4 FI3 RI3 VD4 FO4 RI2 FI2 FI1 RI1 VD2 FO2 PGND VD2 VD1 PGND FO1 VD1 OE PS CLK AGND NC NC T+ T– F– F+ LDCNT1 LDCNT2 FODRF FODRR TRDRF TRDRR G I2 VCC I1 G VS O2 NC O1 NC NC PLVDRY PLVDCI RKEY HKEY1 HKEY2 LDVAR TEMP SYWR SYRD SYRS RKEY HSTOP SYD0 SYD1 SYD2 DSPSCK DSPDAT DSPSTB BEEP CLOCK SYD3 SYD4 SYD5 SYD6 SYD7 RPLAY LDON OPICGA RFLAT VCC GND RACLK LDON HFON SYD3 SYD4 SYD5 SYD6 VLIM AVDD AVREF0 PLVINN DINT SENSE FOK XRT XRT FOK DINT RESET SENSE XT1 XT2 VSS INPGCK HKEY1 HKEY2 TEMP AVSS LDVAR MDOUT AVREF1 SYD0 SYD1 SYD2 SYD7 SYWR SYRD SYRS RKEY BEEP CNTRY EJECT HDON DSPSTB DSPDAT DSPSCK RPLAY HSTOP KHOLD F– T+ F+ T– EFMMON ROUT GOUT TTR EFMAGI EFMAGC AGND AVCC EFMI EFMO RF2-1 ADAG ADAGC ADIPI ADIPO ADLPFO 22KO 22KI WBO TCGO AOUT BOUT EOUT FOUT DVCC DATA CLOCK LATCH DTEMP DGND AGND SGAIN DISC STBY AVCC BIAS FIN EIN BIN AIN TCGI RFADD REFO REFI RF4 RF3 RF2 RF1 BIAS ADIP AGC EMF AGC DIFF DIFF SW and R HPF LPF LOGIC LDCNT1 RAA10 ACRCER PLCK SYRS FEMON DADATA ADDATA DFCK BCLK LRCK DGND VDD3 DOUT DIN X1O X1I VPD VXI ADPON DAPON OPTCNT DCNT1 EMPH1 LDCNT2 X700KO TOTMON TEMON SBCK SBO SBSY SFSY FOK SENSE COUT MCCK DINTX RSTX SYSD0 SYSD1 SYSD2 SYSD3 SYSD4 SYSD5 SYSD6 SYRDX SYWRX VBAT WBI TEST1 TEST0 FODRR FODRF TEST2 X176KO X176KO TRDRF TRDRR SLDRF SLDRR SPDRF SPDRR TCG AGND AIN FIN EIN BIN DGND VDD1 VDD1 DGND EFMI AVCC DGND VDD1 RAD0 RAD1 RAWEX RARASX RAA9 DGND VDD2 RAD3 RAD2 RACASX RAOEX RAA8 RAA7 RAA6 RAA5 RAA4 RAA0 RAA1 RAA2 RAA3 TCRS EFMO RMDAT OPICGA RFLAT RACLK RADAT PLVDRY PLVDCI PLVINN OPICGA LDVAR LDON TEMP RFLAT RACLK RADAT XRT RKEY HKEY2 HKEY1 FODRF FODRR TRDRF TRDRR SLDRF SLDRR SPDRF SPDRR LDCNT1 LDCNT2 DCNT1 FOK SENSE CIN MCCK DINT SYD0 SYD1 SYD2 SYD3 SYD4 SYD5 SYD6 SYD7 SYWR SYRD SYRS 97 SYSD7 CN101 100K R442 R444 2.7K C911 0.1 L651 0.47µH C600 15/10 Q101 2SA17457 C104 0.027 C107 0.012 C131 330P(CH) C109 1/6.3 C106 0.22/16 R101 22K R102 22K C20 1 C110 0.22/16 CK112 IC201 LR37648B R222 1M R207 680 IC101 IR3R55 C111 0.0033 C102 1/6.3 R104 22K R103 22K C161 1/6.3 R154 1.2K L100 10µH C100 10/6.3 XL201 33.8688MHz C211 5P(CH) R203 100 C212 5P(CH) C622 2.2 IC601 MPC17A39 C443 0.47/10 C441 10P(CH) C442 680P IC441 TC7W14FU INVERTER R443 39K R441 12K R408 100K IC404 7SH00FU R403 22K R404 150K IC401 IX2680A TP144 C103 1/6.3 C902 0.01 10K R909 R908 100K R907 180K R903 150 R904 22K R901 1 R902 1 IC901 BA6965FV C907 0.0022 C905 0.0022 C909 0.047 C906 0.0022 C908 0.47 C910 0.047 100K R905 R906 270K C903 3.3/10 R161 1.2K C165 0.033 R205 560K C205 0.1 R206 220K C651 1 IC651 LB1638M C357 0.1 IC351 74ACT02F HEAD DRIVE C354 0.1 C351 100P(CH) D352 SB0209CP D351 SB0209CP 0.039 C361 R361 8.2 C353 10/6.3 R423 22K R425 22K R424 22K R105 390K Q351 2SK2909 Q353 2SK2909 Q352 2SK2911 Q354 2SK2911 C123 390P C124 390P C121 270P(CH) C122 270P (CH) R204 1K C203 0.1 C207 0.1 SW401 EJECT R406 100K SW402 HOLD R405 10K R407 10K R409 100K L601 47µH C601 1/6.3 L602 47µH C602 1/6.3 L603 47µH L604 47µH C603 1/6.3 C604 1/6.3 L600 2.2µH L608 47µH R601 56K TP601 L610 47µH L609 47µH C610 1/6.3 C609 1/6.3 R922 100K R921 330 L204 R106 56K C608 3.3/10 R426 100K TP901 C112 0.033 C952 47/4 C951 47/4 C130 0.1 M902 SLED MOTOR M901 SPINDLE MOTOR M903 LIFT MOTOR SW901 DISC IN X176KO CK102 CK103 CK104 CK101 TP145 TP132 CK108 TP133 TP130 TP131 CK107 TP100 CK111 CK110 CK109 TP139 TP119 TP115 TP105 TP101 TP109 TP106 TP102 TP108 TP103 TP114 TP110 TP118 TP111 TP121 TP122 TP120 TP117 TP116 CN601 TP651 TP652 TP653 TP654 TP655 TP656 TP657 TP658 TP659 TP660 TP661 TP662 TP663 TP664 TP665 TP666 TP610 NAND GATE MOTOR DRIVE TP401 TP403 TP402 TP413 TP208 CK204 CK205 CK206 CK203 CK202 CK201 TP211 TP210 TP209 TP201 CK207 TP206 TP207

7 8 9 10 11 12 The numbers 1 to 18 are waveform numbers shown in page 39. Figure 31 SCHEMATIC DIAGRAM (2/4) P30 P31 P32 5 4 3 2 1 4 3 2 1 8 7 6 5 4 3 2 1 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1 18 17 16 15 14 13 12 11 10 9 8 7 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 26 27 28 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 100 50 49 48 98 99 100 1 2 3 4 5 6 1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 41 40 42 43 44 45 46 47 48 49 50 51 52 53 54 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 70 71 72 73 74 75 1 2 3 4 5 6 7 8 4M D-RAM P 33 1 JACK PWB-A2 CLOCK RKEY RPLAY VSS NC VDD OUT CIN MCCK G I2 VCC I1 G VS O2 NC O1 NC NC PLVDRY PLVDCI RKEY HKEY1 HKEY2 LDVAR TEMP SYWR SYRD SYRS RKEY HSTOP SYD0 SYD1 SYD2 DSPSCK DSPDAT DSPSTB BEEP CLOCK SYD3 SYD4 SYD5 SYD6 SYD7 RPLAY LDON OPICGA RFLAT VCC GND RACLK RADAT PBLAT RCLAT PBOPON MCPGIN INPGIN INPGCK EMPH0 LDON HFON SYD3 SYD4 SYD5 SYD6 VLIM AVDD AVREF0 PLVINN DINT SENSE FOK XRT XRT FOK DINT RESET SENSE XT1 XT2 X1 VSS X2 OEM VDD SLCNT3 SLCNT5 SLCNT1 SLCNT4 SLCNT6 SLCNT2 SWPUP PCNT2 CKSTP DISCIN INNSW DISCPR PDCNT VPP PHOLD PCNT1 CIN ELON PSLINN PSLDCI PSLDRY TEST1 TEST0 SPIN VDD EPCS INPGCK RCPCNT EEPK RTCCK EEPD RTCDT RTCWR RTCCE VSS EMPH0 HPLAY HREC MCPGIN INPGIN INPGCK OPTCNT DIN PBOPON BEEP PBLAT RCLAT RADAT RACLK ADPON DAPON DFCK LRCK BCLK ADDATA DADATA EMPH1 EMPH0 RMDAT DEM0 DEM1 RKEY RPLAY SCLK STDO MCLK LRCK STDI PWAD PWDA PBAULT BEEP AUDATA AUSCLK RCAULT PBMUTE RESET INPGIN MCPGIN DIN OPTCNT INPGCK VCCMIC VCC2.8X VCC2.8 DGND VD SDTI CMODE DEM1 DEM0 PWDA PWAD MCLK LRCK SCLK SDTO HKEY1 HKEY2 TEMP AVSS LDVAR MDOUT AVREF1 SYD0 SYD1 SYD2 SYD7 SYWR SYRD SYRS RKEY VCC CS SK DI DO GND PRTCT BEEP CNTRY PCNT1 E G V E D E EJECT HDON DSPSTB DSPDAT DSPSCK RPLAY HSTOP KHOLD MCPGIN INPGIN EFMMON LDCNT1 RAA10 ACRCER PLCK SYRS FEMON DADATA ADDATA DFCK BCLK LRCK DGND VDD3 DOUT DIN X1O X1I VPD VXI ADPON DAPON OPTCNT DCNT1 EMPH1 LDCNT2 X700KO TOTMON TEMON SBCK SBO SBSY SFSY FOK SENSE COUT MCCK DINTX RSTX SYSD0 SYSD1 SYSD2 SYSD3 SYSD4 SYSD5 SYSD6 SYRDX SYWRX VBAT WBI TEST1 TEST0 FODRR FODRF TEST2 X176KO X176KO TRDRF TRDRR SLDRF SLDRR SPDRF SPDRR TCG AGND AIN FIN EIN BIN DGND VDD1 VDD1 DGND EFMI AVCC DGND VDD1 RAD0 RAD1 RAWEX RARASX RAA9 DGND VDD2 RAD3 RAD2 RACASX RAOEX RAA8 RAA7 RAA6 RAA5 RAA4 RAA0 RAA1 RAA2 RAA3 TCRS EFMO I/O1 I/O2 WE RAS A9 A0 A1 A2 A3 VCC A4 A5 A6 A7 A8 OE CAS I/O3 I/O4 GND E D E V G E RMDAT OPICGA RFLAT RACLK RADAT PBLAT RCLAT PBOPON PLVDRY PLVDCI PLVINN HPLAY HREC RCPCNT PCNT1 RCPCNT DSPDAT DSPSCK DSPSTB PHOLD PCNT1 PCNT2 HPLAY HREC RPLAY PCNT2 PHOLD PSLDCI PSLINN PSLDRY PLVDCI PLVINN PLVDRY PDCNT DISCPR INNSW DISCIN ADDATA DFCK BCLK LRCK DIN ADPON DAPON EMPH1 OPTCNT XRT PSLDRY PSLDCI PSLINN RKEY HKEY2 HKEY1 EFMO HSTOP HPLAY HREC HKEY2 HKEY1 FODRF FODRR TRDRF TRDRR SLDRF SLDRR SPDRF SPDRR LDCNT1 LDCNT2 DCNT1 FOK SENSE CIN MCCK DINT SYD0 SYD1 SYD2 SYD3 SYD4 SYD5 SYD6 SYD7 SYWR SYRD SYRS DADATA 97 SYSD7 L863 4.7 D861 RB491D C863 1/10 C864 33/6.3 L171 10 100K R442 R444 2.7K L651 0.47µH C600 15/10 C774 1 CN4 CN4 C868 1 C865 1/10 L862 47 C869 33/6.3 PO R846 10K C845 47P (CH) R843 100K C842 22P(CH) R848 220K R847 330K R852 1.5M IC202 IX2567AF C202 10/6.3 C201 1 IC201 LR37648B R222 1M R207 680 L202 10µH L100 10µH L201 0.47µH C100 10/6.3 R841 100K C850 0.001 CN701 R849 33K R823 100K R828 270K C825 68P (CH) R829 33K R827 300K R826 10K R821 100K C830 0.001 R832 3.3M C822 39P (CH) C847 10/10 L842 10 C 1 C827 3.3/10 D821 F1J2F C L822 10 C821 220/4 C810 0.33/10 R811 180K R810 180K C172 33/6.3 C171 33/6.3 XL201 33.8688MHz C211 5P(CH) R203 100 C212 5P(CH) C443 0.47/10 C441 10P(CH) C442 680P IC441 TC7W14FU INVERTER R441 12K R408 100K IC404 7SH00FU R403 22K R404 150K IC401 IX2680AF C866 1/10 D862 RB521S30 IC702 TK71345M C431 0.047 1SS361 D431 330K R431 R482 18K C481 0.1 R481 36K R421 100K R205 560K C205 0.1 R206 220K C651 1 IC651 LB1638M R420 1K R419 1K R423 22K R425 22K R424 22K R402 10K R204 1K C203 0.1 C207 0.1 R422 33K R412 10K R411 100K IC402 S29L294A R415 1K R413 1K R414 1K C401 0.1 SW401 EJECT R406 100K SW402 HOLD R405 10K R407 10K R409 100K C886 10/10 L886 0.47µH S80821LN IC431 Q401 2SA17457 R400 3.9K C604 /6.3 L600 2.2µH R458 56K R457 18K R456 8.2K R455 5.6K R454 56K R453 18K R452 8.2K R451 5.6K L204 R861 100K R426 100K D831 1SS372 C831 0.1 C832 0.1 D201 1SS369 D841 F1J2F C 0 L772 4.7µH C508 IC501 AK4514VF R500 4.7 C507 10/6.3 R504 TP610 NAND GATE MOTOR DRIVE TP401 TP403 TP402 TP413 TP208 CK204 CK205 CK206 CK203 CK202 CK201 TP211 TP210 TP209 TP202 TP201 CK207 TP206 TP203 TP204 TP205 TP200 TP405 TP404 TP406 TP412 TP407 TP411 TP408 TP409 TP410 TP810 TP762 TP763 TP764 TP765 TP766 TP767 TP768 TP769 TP770 TP771 TP772 TP773 TP774 TP775 TP776 TP777 TP778 TP779 TP780 TP783 TP784 TP785 TP787 TP781 TP761 TP561 TP562 TP563 TP564 TP565 TP566 TP567 TP568 TP569 TP570 TP571 TP572 TP573 TP574 TP575 TP576 TP577 TP578 TP579 TP580 TP581 TP582 TP584 TP585 TP586 TP588 TP789 TP790 TP791 TP792 TP793 TP590 TP591 TP592 TP593 TP453 TP452 TP451 TP461 TP454 TP464 TP455 TP456 TP457 TP458 TP459 TP460 TP462 TP463 TP481 TP482 TP483 TP487 TP486 TP485 TP484 TP811 TP207

A B C D E F G H 1 2 3 4 5 6 NOTES ON SCHEMATIC DIAGRAM can be found on page 28. Figure 32 SCHEMATIC DIAGRAM (3/4) P30 P31 P32 14 13 12 11 10 9 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 5 4 3 2 1 1 2 3 4 1 2 3 4 5 6 7 8 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 0 1 1 1 2 1 1 2 3 4 5 6 7 8 1 2 3 4 5 1 2 3 4 5 6 7 8 1 2 3 4 5 1 2 3 4 5 6 1 1 2 2 3 3 4 4 5 1 2 3 4 5 6 1 2 3 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 15 14 13 18 17 16 21 22 23 24 20 19 1 2 3 4 5 6 7 8 9 10 11 12 15 14 13 18 17 16 21 20 23 24 22 19 1 2 3 4 5 7 8 9 AUDIO AMP. CONSTANT CURRENT DRIVE POWER DRIVE IC821 IR3M09N 33 1 MIC IN LINE JACK PWB-A2 1 7 1 14 FLEXIBLE PWB FLEXIBLE PWB KEY FLEXIBLE PWB UNIT LCD DRIVER GND P-MODE C-MODE ENTER DISPLY VOL DOWN VOL UP BASS EDIT REC SKIP DOWN SKIP UP STOP PLAY LCD CLOCK LI RI AGND LIHP LOUT RIHP ROUT DGND VEE VCC DIN OPTCNT INPGCK INPGIN MCPGIN R-CH R-CH L-CH L-CH RESET RCAULT PBAULT PBMUTE BEEP AUDATA AUSCLK MCPGIN INPGIN INPGCK OPTCNT DIN PBOPON BEEP PBLAT RCLAT RADAT RACLK ADPON DAPON DFCK LRCK BCLK ADDATA DADATA EMPH1 EMPH0 RMDAT DEM0 DEM1 RKEY RPLAY SCLK STDO MCLK LRCK STDI PWAD PWDA PBAULT BEEP AUDATA AUSCLK RCAULT PBMUTE RESET INPGIN MCPGIN DIN OPTCNT INPGCK VCCMIC VCC2.8X VCC2.8 DGND VD SDTI CMODE DEM1 DEM0 AOUTL AOUTR VCOM AGND VB VA VRDA VRAD AINR VCMR VCML AINL PWDA PWAD MCLK LRCK SCLK SDTO ROUT LOUT VCC DGND RIHP LIHP AGND RI LI VEE L-CH R-CH KEY PLAY DATA NC NC NC NC PCNT1 EAOUT GND OUT VCC PWM STATE ROSC OSC VREF EAIN– DB EAIN+ OSCIN OSCOUT GND VCC OSCOUT OSCIN EAIN+ DB EAIN– VREF OSC ROSC STATE PWM VCC OUT GND EAOUT VCC GND OUT VSS VDD RCPCNT PCNT1 DSPDAT DSPSCK DSPSTB HPLAY HREC RPLAY PCNT2 PHOLD PSLDCI PSLINN PSLDRY PLVDCI PLVINN PLVDRY MICOM2.5V TOP LAY EC EY2 EY1 NC NC D493 015Z5.1Y L863 4.7 D861 RB491D C863 1/10 C864 33/6.3 L171 10 D494 15AZ7.5Y C774 1 CN451 CN482 C843 100P(CH) C868 1 C865 1/10 L862 47 C869 33/6.3 POWER DRIVE IC841 IR3M09N L841 4.7 R844 15K C848 1/6.3 R846 10K C845 47P (CH) C844 100P(CH) R843 100K C842 22P(CH) R848 220K R847 330K R852 1.5M R841 100K C850 0.001 CN701 R849 33K D822 RB521S30 R831 100K C829 0.01 C823 100P(CH) L821 4.7 R823 100K R828 270K R824 15K C825 68P (CH) R829 33K C828 1/6.3 R827 300K R826 10K R821 100K C830 0.001 R832 3.3M C822 39P (CH) C824 100P(CH) C847 10/10 L842 10 C846 1/10 C827 3.3/10 D821 F1J2F C826 1/10 L822 10 C821 220/4 C810 0.33/10 R811 180K R810 180K C172 33/6.3 C171 33/6.3 C866 1/10 D862 RB521S30 IC702 TK71345M R878 100K R874 470K C878 3.3/10 R873 1K IC872 TC7W32FU C877 10/6.3 IC871 S8327B30 C874 10/10 C872 1/6.3 Q871 NDS335N C871 1/6.3 D873 1SS372 C873 1 C849 0.01 R851 100K D842 RB521S30 D802 SB10015C IC803 NDH831N R482 18K C481 0.1 R481 36K C875 0.22/16 R877 100K R876 100K C880 0.01 C879 1/6.3 IC874 TC7S00FU CHARGE DRIVER R882 100K R881 100K R879 100K R880 100K R809 100K D877 1SS360 IC804 RN4904 Q842 NDS335N Q822 NDS335N C881 1/6.3 D875 1SS378 IC875 TK71325M R872 100K Q872 DTC144 EE Q873 2SJ305 IC873 S80827LN Q401 2SA17457 R400 3.9K R458 56K R457 18K R456 8.2K R455 5.6K R454 56K R453 18K R452 8.2K R451 5.6K R861 100K D831 1SS372 C831 0.1 C832 0.1 D841 F1J2F D871 RB491D 47 R875 100K IC876 RN4904 R814 3.9K R818 10K R815 3.9K C802 1 Q801 2SD1950 D801 015Z5.1Y R816 1.2K IC800 HN1C03FU R801 680K R819 270 C808 1/6.3 R808 39K R807 27K R806 680K C807 0.1 R805 470K C806 3.3/10 L801 1 C805 100/6.3 C804 1/6.3 IC801 HAT1025R CONSTANT CURRENT DRIVE R804 100K Q803 DTC144 EE Q802 DTC144 EE R803 100K R802 390K C803 0.1 IC805 UMD3N D800 RB491D L888 CORE L887 CORE R817 680 C759 0.056 C761 1/6.3 C762 1/6.3 C702 10/6.3 R756 27K R701 100 C756 0.68 R762 3.3K R761 3.3K R754 330K R757 27K C757 0.68 IC703 IR3R54N AUDIO AMP. IC701 IR3R54N C703 0.01 R703 150K C758 3.3/10 C755 0.01 C753 1 C701 10/6.3 R702 100 L771 47µH C771 33/6.3 C772 33/6.3 C773 0.22/16 IC771 TK71225M C775 0.01 L710 0.47µH C710 0.1 C510 2.2 C509 2.2 R502 470 R501 470 C502 0.0022 C501 0.0022 C504 3.3/10 C503 3.3/10 L500 4.7µH L772 4.7µH C508 1/6.3 C500 10/6.3 IC501 AK4514VF R500 4.7 C507 10/6.3 D492 015Z5.1Y L491 4.7µH C722 3.3/10 C721 3.3/10 C723 0.001 C735 0.001 C736 0.01 C451 0.001 C724 0.001 C731 0.22 R727 10K R723 6.8K R724 6.8K C725 3.3/10 C727 1 Q721 2SC4213B R725 100 R726 39K R728 1K C726 3.3/10 R713 10K Q711 RN1444A R717 1K C712 100P (CH) C714 1/6.3 (CH) R714 10K C713 1/6.3 C711 100P (CH) C715 0.1 R715 100K R716 100K C734 0.1 C733 0.1 R720 8.2K R719 8.2K R712 5.6K R711 5.6K C754 1 R753 150K L751 47µH L752 47µH C768 0.22/16 R752 82 C767 0.22/16 R751 82 R729 2.7K R730 2.7K TP721 C491 0.1 D491 015Z5.1Y R504 20K R503 20K R767 1K R768 1K R766 10 R765 15 C751 0.082 C752 0.082 R492 1K L452 L454 L453 L457 L458 L456 J702 J703 HEADPHONE J701 J801 DC IN L702 L703 L713 L714 L704 L712 L711 X700K TP810 TP762 TP763 TP764 TP765 TP766 TP767 TP768 TP769 TP770 TP771 TP772 TP773 TP774 TP775 TP776 TP777 TP778 TP779 TP780 TP783 TP784 TP785 TP787 TP781 TP761 TP561 TP562 TP563 TP564 TP565 TP566 TP567 TP568 TP569 TP570 TP571 TP572 TP573 TP574 TP575 TP576 TP577 TP578 TP579 TP580 TP581 TP582 TP584 TP585 TP586 TP588 TP789 TP790 TP791 TP792 TP793 TP590 TP591 TP592 TP593 TP453 TP452 TP451 TP461 TP454 TP464 TP455 TP456 TP457 TP458 TP459 TP460 TP462 TP463 TP481 TP482 TP483 TP487 TP486 TP485 TP484 TP729 TP712 TP713 TP711 TP714 TP703 TP705 TP708 TP701 TP709 TP704 TP702 TP707 TP722 TP723 TP724 TP725 TP726 TP 727 TP728 TP807 TP808 TP809 BATTERY TERMINAL EXT.BATTERY TERMINAL TP805 TP806 TP804 TP803 TP811 TP500 TP802 TP801

7 8 9 10 11 12 The numbers 1 to 18 are waveform numbers shown in page 39. Figure 33 SCHEMATIC DIAGRAM (4/4) 0V 1.0V 2.1V 0V 5.0V 0V 0V 0V 5.0V 5.0V 0V 0V 0V 5.0V 0V 0V 0V 0V 0V 0V 0V 0V 5.0V 0V 0V 0V 5.0V 5.0V 0V 0V 0V 5.0V 0V 0V 2.5V 10.8V 2.5V 2.5V 0V 0V 0V 0V 1.0V 1.0V 1.0V 1.0V 1.0V 0V 0V 2.5V 0V 0V 0.95V 0V 0.35V .035V 0V 0V 2.5V 2.5V 0.25V 0.25V 0V 2.23V 2.5V 0.7V 0.7V 0.7V 0.7V 1.29V 1.26V 0.7V 1.26V 1.26V 1.26V 1.26V 1.26V 2.52V 2.52V 0.18V 2.52V 2.52V 0V 0V 1.46V 2.52V 0V 0V 2.51V 1.26V 1.26V 1.26V 1.26V 1.26V 1.8V 1.26V 1.26V 1.26V 0V 1.26V 1.26V 0V 1.26V 1.26V 1.26V 1.26V 2.52V 0V 0V 1.0V 1.0V 1.0V 1.0V 1.5V 1.7V 2.5V 1.9V 0.9V 1.4V 0.6V 0.6V 0.6V 2.53V 0.6V 1.0V 1.0V 1.0V 1.0V 1.8V 2.0V 1.6V 1.7V 0V 1.0V 2.5V 1.27V 0V 1.27V 1.27V 1.27V 1.27V 1.26V 2.2V 1.43V 2.15V 0V 0V 0V 0V 1.0V 0V 0V 0V 0V 0V 0V 0V 0V 0.6V 0.6V 0.6V 1.4V 0.9V 2.5V 2.5V 0.8V 0.9V 0.9V 1.0V 1.8V 0V 2.0V 1.3V 1.5V 1.1V 1.7V 2.5V 1.6V 1.6V 0V 2.0V 1.0V 0.9V 0V 0V 0V 0V 0V 2.15V 0V 0V 0V 0V 0.8V 2.15V 0V 1.0V 1.0V 2.3V 2.15V 2.15V 0V 1.0V 1.0V 0V 0V 0V 0V 0V 0V 2.15V 0V 2.15V 1.0V 2.15V 0V 0V 1.0V 2.15V 2.15V 0V 2.5V 0.5V 0.6V 0.5V 1.0V 1.2V 0.9V 1.2V 0.4V 2.45V 2.5V 0V 9 8 7 6 5 4 3 2 1 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 PIN NO. VOLTAGE IC101 9 8 7 6 5 4 3 2 1 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 40 39 38 37 36 35 34 33 32 31 50 49 48 47 46 45 44 43 42 41 PIN NO. VOLTAGE IC201 PIN NO. VOLTAGE 51 64 63 62 61 60 59 58 57 56 55 54 53 52 68 67 66 65 69 80 79 78 77 76 75 74 73 72 71 70 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 2.5V 0V 0V 0V 0V 0V 0V 2.5V 2.5V 1.18V 0V 0V 1.18V 1.18V 2.42V 2.1V 0V 2.1V 2.5V 0V 2.5V 0V 0V 0V 2.9V 1.8V 0V 2.5V 2.5V 2.5V 1.48V 2.5V 0V 0V 0V 2.5V 2.46V 2.5V 0V 2.5V 0.27V 1.5V 2.47V 2.5V 2.2V 2.43V 0.7V 0.8V 0.8V 0.8V 0.95V 1.1V 0.95V 1.1V 0.8V 0V 2.47V 2.96V 0V 0V 0V 2.5V 0V 0V 2.5V 0V 2.5V 2.35V 2.75V 2.75V 0V 0V 0V 3.12V 3.12V 0V 0V 0.4V 0V 2.5V 2.5V 2.5V 0V 2.5V 2.5V 2.5V 2.5V 0V 0V 2.0V 0V 2.5V 2.5V 0V 0V 1.2V 0V 0.45V 2.5V 0.3V 9 8 7 6 5 4 3 2 1 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 40 39 38 37 36 35 34 33 32 31 50 49 48 47 46 45 44 43 42 41 PIN NO. VOLTAGE IC401 PIN NO. VOLTAGE 51 64 63 62 61 60 59 58 57 56 55 54 53 52 68 67 66 65 69 80 79 78 77 76 75 74 73 72 71 70 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 PIN NO. VOLTAGE IC202 5 4 3 2 1 PIN NO. VOLTAGE IC404 2.5V 2.5V 0V 0V 4 3 2 1 PIN NO. VOLTAGE IC431 1.0V 1.2V 1.1V 0V 1.1V 1.2V 1.3V 2.5V 5 4 3 8 7 6 2 1 PIN NO. VOLTAGE IC441 2.5V 0V 1.2V 1.2V 0V 2.5V 0V 2.5V 5 4 3 2 1 PIN NO. VOLTAGE IC402 8 7 6 5.0V 0V 5.0V 0V 5.0V 5.0V 5.0V 5.0V 5 4 3 2 1 PIN NO. VOLTAGE IC801 8 7 6 5.0V 5.0V 5.0V 0V 0V 5.0V 5.0V 0V 5 4 3 2 1 PIN NO. VOLTAGE IC803 8 7 6 1.4V 0V 0V 2.5V 2.8V 5 4 3 2 1 PIN NO. VOLTAGE IC771 0V 0V 0V 4.5V 7.7V 5 4 3 2 1 PIN NO. VOLTAGE IC702 1.25V 0.9V 1.25V 1.23V 1.1V 0V 0.8V 4.8V 0V 0.4V 1.0V 1.0V 5 4 3 2 1 PIN NO. VOLTAGE IC821 6 11 10 9 8 7 12 5.0V 4.8V 0V 0V 0V 5 4 3 2 1 PIN NO. VOLTAGE IC871 4.8V 4.8V 0V 0V 4 3 2 1 PIN NO. VOLTAGE IC873 3.5V 2.97V 0V 0V 4.9V 4 5 3 2 1 PIN NO. VOLTAGE IC874 5.0V 0V 5.0V 0V 5.0V 5.0V 5. 0V 5.0V 5 4 3 2 8 7 6 1 PIN NO. VOLTAGE IC872 1.25V 0.9V 1.33V 1.22V 1.22V 0V 0V 4.8V 0V 0.4V 1.0V 1.0V 5 4 3 2 1 PIN NO. VOLTAGE IC841 6 10 9 8 7 11 12 9 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 PIN NO. VOLTAGE IC501 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 32 31 30 29 28 27 36 35 34 33 26 25 15 14 13 12 11 10 PIN NO. VOLTAGE IC601 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V –2.85V 0V 0V 2.75V 0.8V 0V 0V 0V 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 PIN NO. VOLTAGE IC701 1.3V 0V 0V 0V 0V 0V 0V 0.95V 0V 1.9V 0V 1.95V 2.5V 0V 0V 0V –2.85V 0V 0V 2.78V 0.83V 0V 0V 0V 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 PIN NO. VOLTAGE IC703 0V 0V 0V 0V 0V 0V 2.4V 2.45V 1.87V 0V 2.5V 2.1V 0V 2.1V 0V 2.5V 2.5V 0V 0V 0V 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 PIN NO. VOLTAGE IC901 0V 0V 0V 2.5V 4.8V 5 4 3 2 1 PIN NO. VOLTAGE IC875 5.0V 0V 0V 0V 2.5V 5.0V 5 6 4 3 2 1 PIN NO. VOLTAGE IC876 22 21 24 23 20 19 18 17 7.7V 7.6V 7.6V 0V 0V 0V 5 4 3 2 1 PIN NO. VOLTAGE IC804 6 0V 0V 2.5V 0V 0V 0V 1.2V 2.5V 1.2V 0V 9 8 7 6 5 4 3 2 1 10 PIN NO. VOLTAGE IC651 0V 0V 2.5V 0V 0V 2.5V 0V 1.0V 2.5V 0V 1.0V 2.5V 0V 4.5V 9 8 7 6 5 4 3 2 1 14 13 12 11 10 PIN NO. VOLTAGE IC351 5.14V 5.14V 5.09V 0V 5.09V 5.15V 5.16V 10.33V 5 4 3 2 1 PIN NO. VOLTAGE KIC1 8 7 6 5.16V 5.16V 5.16V 0V 5.16V 5.16V 5.16V 10.34V 5 4 3 2 1 PIN NO. VOLTAGE KIC2 8 7 6

A B C D E F G H 1 2 3 4 5 6 Figure 34 WIRING OF P.W.BOARD (1/5) The numbers 1 to 18 are waveform numbers shown in page 39. J801 C161 R154 Q101 IC202 L202 C601 C622 C202 IC601 C602 L601 L602 L603 L604 C604 C603 L600 C353 C354 D351 Q354 Q352 L801 C805 C804 C874 C130 C609 L609 L610 L608 XL201 C610 C357 D352 C351 Q353 IC351 Q351 C829 R831 D822 C828 IC804 Q803 Q802 C823 C824 R824 C821 C806 C600 C608 C212 C211 R222 IC651 L651 C651 D431 C843 C401 R601 IC201 C172 L171 R415 R844 C844 IC431 C431 R431 R210 R441 R444 R204 C203 R207 R442 C443 C441 R411 C442 R443 R412 R414 R413 R203 L204 C171 IC404 IC441 D201 1 1 1 1 1 1 1 1 1 5 10 15 18 19 20 25 30 35 36 7 5 10 8 14 5 6 10 1 1 3 4 6 1 1 3 4 6 4 5 8 4 5 8 6 7 12 1 2 3 4 6 7 12 3 4 5 4 8 5 4 5 8 3 4 5 1 25 26 1 5 10 11 15 20 30 35 45 40 50 51 75 76 80 85 90 95 70 65 60 55 100 20 15 10 5 Q401 R400 IC402 C848 L886 R861 C886 C866 D862 IC702 R847 C845 C849 D842 R851 R408 IC821 IC841 C822 C850 R841 R843 C842 R852 R827 R832 R823 C830 C825 R821 R826 R849 R828 R810 R803 R829 R407 R846 R848 C810 R813 R811 C807 R806 R805 R804 C803 D802 R809 IC800 R802 R801 C808 R808 R807 R818 IC801 IC803 R815 D801 R817 R814 D800 BATTERY TERMINAL (+) BATTERY TERMINAL (-) 10 10 11 13 1 MAIN PWB-A1 (TOP) 12 4 3 DC IN

7 8 9 10 11 12 Figure 35 WIRING OF P.W.BOARD (2/5) 1 1 100 95 90 85 80 75 1 5 10 13 15 20 24 25 30 35 37 45 36 46 12 70 65 60 55 51 50 45 40 35 30 25 20 15 10 5 1 1 1 1 5 8 1 1 1 4 5 3 3 4 6 4 3 4 5 2 3 4 3 4 5 26 76 5 15 10 11 20 14 C103 IC101 C104 C112 C102 IC901 R419 R422 R420 R455 R409 L100 R406 R405 C908 C911 C905 R453 CN451 R902 R901 R908 R907 R903 R904 R922 R921 CN601 R451 R454 R452 C361 R361 C903 R906 R905 C907 C906 C909 C910 C902 R426 R909 R402 C100 R404 R403 C131 R106 CN101 C121 C124 R101 R102 R103 R104 IC401 R425 R423 R424 C106 C107 C109 C110 C111 C122 C123 R205 R206 C205 R161 C165 C201 L201 C826 C865 C868 D861 D841 C869 C951 L822 D821 C952 C864 CN701 R1 R2 R3 R4 R5 R8 R6 R7 R9 R10 R11 C481 R481 C847 C846 L842 L841 Q842 C863 IC875 R880 C875 R882 D877 IC876 CN482 R819 IC805 Q801 L871 C878 IC874 R875 D875 D873 IC873 L862 R421 L821 Q822 R872 Q872 D871 C873 Q873 C832 R878 C871 R876 C880 Q871 C877 R881 R879 C881 C879 R877 L863 C827 C831 D831 IC871 C872 IC872 L888 L887 C802 R458 R456 R457 R105 R482 R816 R873 R874 SW401 EJECT 1 1 22 22 FROM PICKUP FLEXIBLE PWB P40 1-D 1 1 33 33 FROM AUDIO FLEXIBLE PWB (254) P39 9-H 1 14 FROM KEY FLEXIBLE PWB (231) P40 5-F 1 1 16 16 FROM MECHA FLEXIBLE PWB (8) P40 6-C 1 1 7 7 FROM LCD FLEXIBLE PWB P40 4-H SW402 HOLD 17 9 18 16 2 MAIN PWB-A1 (BOTTOM) 15 14 EXT. BATTERY TERMINAL (220) TP783 TP489 TP487 TP486 TP807 TP482 TP481 TP483 TP484 TP485 TP809 TP808 TP806 TP803 TP805 TP801 TP802 TP810 TP659 TP210 TP209 TP404 TP405 TP407 TP410 TP403 TP411 TP409 TP408 TP764 TP769 TP774 TP779 TP784 TP790 TP787 TP791 TP792 TP793 TP785 TP781 TP780 TP778 TP777 TP776 TP775 TP773 TP772 TP771 TP770 TP768 TP767 TP766 TP765 TP763 TP762 TP761 TP211 TP208 TP412 TP664 TP653 TP663 TP901 TP651 TP413 TP652 TP654 TP657 TP655 TP601 TP656TP660 TP661 TP665 TP658 TP666 TP662 TP457 TP462 TP460 TP610 TP804 TP464 TP205 TP406 TP456 TP207 TP458 TP451 TP811 TP401 TP401 TP203 TP145 TP139 TP100 TP459 TP461 TP455 TP453 TP452 TP454 TP206 TP201 TP106 TP121 TP109 TP108 TP122 TP120 TP119 TP117 TP111 TP105 TP103 TP101 TP102 TP110 TP115 TP116 TP144 TP114 TP463 TP118

Figure 36 WIRING OF P.W.BOARD (3/5) A B C D E F G H 1 2 3 4 5 6 J703 HEADPHONES J701 LINE J702 MIC IN JACK PWB-A2(TOP) R766 R767 D491 L458 L457 C751 D493 R768 L453 L454 C714 C491 R765 C752 L751 R751 R753 R716 L491 L702 Q711 D494 C713 D492 R492 L703 L704 C703 R701 R713 C711 R703 L714 C726 R729 C721 R730 C722 C736 R724 R728 R727 C775 IC771 C774 C773 L771 C772 C734 C725 C731 L710 C710 C733 R503 R502 IC701 R702 R717 C702 C771 R711 R712 R719 R720 C701 C503 C504 R504 L500 R501 C509 C510 R715 C715 C508 C502 C501 C507 C759 C500 1 1 1 12 13 24 12 13 24 12 13 24 R500 R754 L752 C768 R752 C757 C756 R762 IC501 IC703 C755 R714 C753 R761 C762 C761 C758 C767 C754 R756 R757 8 7 6 5

7 8 9 10 11 12 Figure 37 WIRING OF P.W.BOARD (4/5) JACK PWB-A2(BOTTOM) CN701 TO MAIN PWB P37 10-H AUDIO FLEXIBLE PWB(254) MD-SS702H PWBPOW_B L456 C451 L452 C712 L713 R723 C724 L712 L711 C723 R725 R726 C727 C735 Q721 L772 TP701 TP728 TP727 TP723 TP724 TP729 TP722 TP721 TP725 TP726 TP702 TP592 TP591 TP709 TP708 TP707 TP585 TP586 TP588 TP590 TP714 TP704 TP703 TP705 TP713TP712 TP593 TP711 TP500 TP576 TP581 TP580 TP578 TP575 TP584 TP582 TP579 TP577 TP574 TP573 TP572 TP571 TP570 TP569 TP568 TP567 TP566 TP565 TP564 TP563 1 1 33 TP562 TP561

Figure 38 WIRING OF P.W.BOARD (5/5) A B C D E F G H 1 2 3 4 5 6 TO MAIN PWB P37 8-G PICKUP UNIT (15) M902 SLED MOTOR M901 SPINDLE MOTOR M903 LIFT MOTOR SW902 DISC PROTECT MECHA FLEXIBLE PWB UNIT (8) MAGNETIC HEAD FLEXIBLE PWB (23) MAGNETIC HEAD (32) KEY FLEXIBLE PWB UNIT (231) CN101 BK RD SW901 DISC IN TO MAIN PWB P37 10-D CN601 TO MAIN PWB P37 8-D CN451 TO MAIN PWB P37 12-D LCD (232) CN482

WAVEFORMS OF MD CIRCUIT NORM:200kS / s 1994 / 12 / 15 22:54:19 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.000V Main : 10K Zoom : 10K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : NORMAL Type : EDGE CH4 Detay : 0.0ns Hold OFF : MINIMUM T TP208 (FEOUT) CK204 (FOK) TP122 (F+) CK205 (SENSE) Stopped CH1=1mV DC 10:1 CH3=5V DC 10:1 CH4=2V DC 10:1 (50ms/div) 50ms/div CH2=500mV DC 10:1 T 1 4 3 2 1 2 3 4 NORM:100MS / s 1994 / 12 / 16 00:24:17 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 5K Zoom : 5K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : AUTO Type : EDGE CH3 Detay : 0.0ns Hold OFF : MINIMUM T SDTi MCLK SCLK LRCK Stopped CH1=2V DC 10:1 CH3=2V DC 10:1 CH4=2V DC 10:1 (50us/div) 50us/div CH2=2V DC 10:1 T 1 4 3 2 5 6 7 8 ENV 1994 / 12 / 16 01:03:40 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.000V CH4 : 0.00V =Trigger= Mode : NORMAL Type : EDGE CH2 Detay : 0.0ns Hold OFF : MINIMUM T TP139 (EFM) TP210 (TEOUT) TP209 (TOTAL) Stopped CH1=1V DC 10:1 CH3=500mV DC 10:1 (2ms/div) 2ms/div CH2=2V DC 10:1 T 1 2 9 10 11 ENV 1994 / 12 / 15 23:31:21 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : NORMAL Type : EDGE CH1 Detay : 0.0ns Hold OFF : MINIMUM T SPDRR TP601 (VM) Stopped CH1=2V DC 10:1 (50ms/div) 50ms/div CH2=2V DC 10:1 T 1 2 12 13 1994 / 12 / 15 08:57:26 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.000V CH4 : 0.0V =Trigger= Mode : NORMAL Type : EDGE CH1 Detay : 0.0ns Hold OFF : MINIMUM T TP139 (EFM) TP210 (TEOUT) TP209 (TOTAL) Stopped CH1=2V DC 10:1 (2ms/div) 2ms/div CH2=2V DC 10:1 1 2 ENV T CH3=500mV DC 10:1 9 10 11 1994 / 12 / 15 09:10:03 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.000V CH2 : 0.00V Main : 4K Zoom : 4K CH3 : 0.000V CH4 : 0.0V =Trigger= Mode : NORMAL Type : EDGE CH1 Detay : 0.0ns Hold OFF : MINIMUM T CK110 (HPFO) CK108 (WBO) Stopped CH1=500mV DC 10:1 (20us/div) 20us/div CH2=2V DC 10:1 1 2 ENV 16 17 FULL 20MHz Bandwidth ON Smooth OFF 1994 / 12 / 18 09:26:46 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : AUTO Type : EDGE CH2 Detay : 0.0ns Hold OFF : MINIMUM T TP208 (FEOUT) TP210 (TEOUT) TP651 (SL+) TP652 (SL-) Stopped CH1=2V DC 10:1 CH3=2V DC 10:1 CH4=2V DC 10:1 (1s/div) 1s/div CH2=2V DC 10:1 1 4 3 2 ENV 1 10 14 15 1994 / 12 / 16 01:23:16 =Filter= =Tracel= P-P 1.280V =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.000V CH2 : 0.00V Main : 1K Zoom : 1K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : AUTO Type : EDGE CH1 Detay : 0.0ns Hold OFF : MINIMUM T TP139 (EFM) Stopped CH1=2V DC 10:1 (500ms/div) 500ms/div 1 MORM:200MS/s 9 1994 / 12 / 15 09:58:45 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : AUTO Type : EDGE CH1 Detay : 0.0ns Hold OFF : MINIMUM T TP208 (FEOUT) TP210 (TEOUT) SPDRR TP601 (VM) Stopped CH1=2V DC 10:1 CH3=2V DC 10:1 CH4=2V DC 10:1 (1s/div) 1s/div CH2=2V DC 10:1 1 3 4 2 ENV 1 10 12 13 1994 / 12 / 15 08:39:46 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.00V CH4 : 0.0V =Trigger= Mode : AUTO Type : EDGE CH1 Detay : 0.0ns Hold OFF : MINIMUM T TP210 (TEOUT) TP651 (SL+) TP652 (SL-) Stopped CH1=2V DC 10:1 CH3=2V DC 10:1 (1s/div) 1s/div CH2=2V DC 10:1 1 3 2 NORM:1kS/s 10 14 15 1994 / 12 / 15 21:54:52 =Filter= =Offset= =Record Length= Smoothiing : OFF BW : FULL CH1 : 0.00V CH2 : 0.00V Main : 10K Zoom : 10K CH3 : 0.00V CH4 : 0.00V =Trigger= Mode : NORMAL Type : EDGE CH2 Detay : 0.0ns Hold OFF : MINIMUM T T TP139 (EFM) TP210 (TEOUT) TP219 (T+) TP121 (T-) Stopped CH1=2V DC 10:1 CH3=1V DC 10:1 CH4=1V DC 10:1 (500us/div) 500us/div CH2=2V DC 10:1 1 3 4 2 ENV 9 10 11 18

TROUBLESHOOTING It is advisable to use the TEST mode (refer to Error Data Display Mode, P15) indicating the causes of troubles before starting repair. Causes of operation errors (up to 10 errors) are recorded as error codes. This information is useful for repair. When does not function When the CD section does not operate When the objective lens of the optical pickup is dirty,this section may not operate.Clean the objective lens,and check the playback operation.When this section does not operate even after the above step is taken,check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC(Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. Is the power supply turned on when the remote control button or main unit button is pressed? No Perform the check stated in item "Power is not turned on when the PLAY button is pressed". Perform the check stated in item "Abnormal display". No Yes Does the display operate normally? Is playback state set? Yes Perform the check stated in item "Playback state connot be set". No Is audio output normal? Yes Perform the check stated in item "Audio playback circuit". No Is recording/playback operation normal? Yes Perform the check stated in item "Recording/playback operation". No • Power is not turned on when the / button is pressed. No No Yes Check the periphery of remote controller and main unit headphone terminal (J703) and IC401. No Is the pin 5 of IC401 in H state? Is operation normal when the main body button is pressed? Check the position of Hold switch. Is power turned on when the remote control button is pressed? No Are IC401 pin 50 set to "L"? Check the DISC IN (SW901) switch of mechanism PWB. Yes Yes Is clock supplied to the pins 11 and 14 of IC401? No Check that voltage is applied to the periphery of IC403. Yes Is 2.5V applied to TP801? No Check whether there is solder touch of part connected to the +2.5V line.

Yes Check whether there is defective solder joint of audio signal line between IC703 and J703 No Yes Is audio wavefrom output from J703 pins 3 and 4. Check the pins 5 and 6 of IC703. No Yes Is audio wavefrom output from IC703 pins 18 and 19. Check IC201 pins 70 to 72, pin 74 and IC501 pins 9, 10, 11, 15 No • Abnormal display No Yes Is waveform output from IC 401 pins 45 to 47? Check for pattern breakage of flexible PWB, check for defects of display microcomputer (replace the display unit). Is waveform output from CNS 482 pins 1 to 3? Are the pin7 (VCC) and pin 6 (GND) normal? • Playback state cannot be set Is initialization performed normally in case of high- reflection disc playback? Yes Check between IC401 and CNS482. No Check the periphery of IC401. Does the playback time display advance? Yes Position check in INNER mode Check IC201 and IC202 connection line. Is the lead-in photointerrupter set to OFF when the optical pickup moves to the innermost periphery in NORMAL mode? (Is TP660 in H level?). Check the lead-in photointerrupter, mechanical flex PWB soldering and CNS601 connection. No Ia an attempt to repeat repeatedly the TOC part performed on the low-reflection disc? Yes No No Replace the disc. No • Audio playback clrcult When it has been ascertained that the address up to cluster address is normal in the TEST mode. Yes Is audio wavefrom output from IC501 pins 19 and 20? Check headphones jack,and periphery of headphone. Although the playback time display is acting., no sound is given during playback in the normal mode.

• The spindle motor fails to run.Does the head move No Does the waveform appear on the IC201 pins 24 and 25 after TEST mode AUTO2 completion and in this state? Check the IC201 periphery. Yes Does waveform appear on the IC601 pin 13? Does waveform appear on IC901 pins 1, 19 and 20? Replace the spindle motor. Yes No L608, IC201, IC901, CN601 and flex, etc. soldering check No Replace. IC601 Yes • Recording/playback operation Insert a low reflection disc, and ascertain audio output by normal playback, and then set TEST REC mode. Yes Does the head move down, failing to start record even when the continuous record mode is set after address? Check voltage of pins 52 and 53 of IC201, pins 2, 4, 7, and 9 of IC651, pins 3 and 14 of CNS601. Check whether disc is record- inhibited. No Does the RF waveform of TP201 appear when playback is Does level of pins 34 of IC401 and pin 17 of IC101 change depending on record and playback? Is RF pattern output from IC201 pin 50? Yes No Check for soldering failure of IC201 . No Check periphery of IC401 and IC101. Check whether there is any damage in IC101, periphery of laser diode. Yes Check for defects of IC351 in head drive flexible PWB, Q351 to 354, head, flexible PWB. No Yes Is audio monitor output given in normal mode LINE IN record? Check waveforms of pins 9 to 12 of IC501, pins 70 to 73 of IC201. Is waveform obtained on IC501 pins 3 and 6? No Yes Check whether the pin 7 of IC501 and the pin 59 of IC201 are in H state. No No Does voltage on the IC701 pins 13 to 15 change in case of record VOLUME UP/DWN? Is audio waveform observed on the pins 18 and 19 of IC703? Yes Check whether input waveform is observed on the pins 5 and 6 of IC703. Yes

1 P120 SWP UP Output Asterisk input Output for pull-up 2*~7* P121~P126 P121~P126 Output Not used 8 P127 OEM Input Product brand ID input 9 VDD VDD Input Positive power supply 10* X2 X2 Input Not used 11 X1 X1 Input Main system clock input 12 VSS VSS Input Ground potential 13* XT2 XT2 Input Not used 14 XT1 XT1 Input Subsystem clock input 15 RESET RESET Input Microcomputer hard reset input 16 INPUT0 DINT Input System LSI interruption request input 17 P01 SENSE Input System LSI servo sense input 18 P02 FOK Input Focus OK signal input 19 P03 XRST Outout System LSI hard reset output 20* P04 P04 Output Not used 21 P05 HDON Output Record head current control output 22 P06 VLIM Intput Volume limiting switch input 23 AVDD AVDD Input A/D converter analog positive power 24 AVREF0 AVREF0 Input A/D converter reference voltage input 25 ANI0 PLVINN Input Built-in battery voltage detection input 26 ANI1 PLVDCI Input DC jack voltage detection input 27 ANI2 PLVDRY Input Dry cell voltage detection input 28 ANI3 RKEY Input Remote controller key operation detection input 29 ANI4 HKEY1 Input Main unit key operation detection input 1 30 ANI5 HKEY2 Input Main unit key operation detection input 2 31 ANI6 TEMP Input Ambient temperature detection input 32 ANI7 CNTRY Intput Product destination ID input 33 AVSS AVSS Intput A/D converter ground potential 34 ANO0 LDVAR Output P.U. laser power set output 35* ANO1 MDOUT Output Internal motion mode output 36 AVREF1 AVREF1 Output D/A converter reference voltage input 37 P70 SYWR Output System LSI write enable output 38 P71 SYRD Output System LSI read enable output 39 P72 SYRS Output System LSI register selection output 40 P20 - Output Not used 41 SO1 RMDAT Output Remote controller display data output 42 P22 - Output 43 P23 HSTOP Input Main unit STOP key operation detection input 44 P24/BUZ BEEP Output Beep tone pulse output 45 P25 DSPSTB Output Main unit display control strobe output 46 SO0 DSPDAT Output Main unit display control serial data output 47 SCK0 DSPSCK Output Main unit display control serial clock output 48~55 P80~P87 SYD0~SYD7 In/Output System LSI parallel data bus 56 P40 EJECT Input Eject lever operation detection input * 57 P41 KHOLD Input Main unit key hold switch input 58 P42 RPLAY Input Remote controller PLAY key operation detection input 59* P43 HFON Output P.U. high frequency superposition control output IC401 RH-iX2680AF03(IX2680AF):System Microcomputer (1/2) FUNCTION TABLE OF IC Pin No. Function Port Name Terminal Name Input/Output In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

60 P44 LDON Output P.U. laser ON/OFF control output 61 P45 OPICGA Output P.U. detection sensitivity selection output 62 P46 RFLAT Output RF amp. IC data latch output 63 P47 RACLK Output RF/audio IC data clock output 64 P50 RADAT Output RF/audio IC serial data output 65 P51 PBLAT Output Playback audio IC data latch output 66 P52 RCLAT Output Record audio IC data latch output 67 P53 PBOPON Output Audio IC output stage control output 68 P54 MCPGIN Input Mic plug insertion detection input 69 P55 INPGIN Input Line/digital plug insertion detection 70 P56 INPGCK Input Line/digital plug type detection 71 P57 RCPCNT Output Record circuit power control output 72 VSS VSS Output Ground potential 73 P60 EMPHO Output Audio emphasis control output 0 74 P61 HPLAY Input Main unit PLAY key operation detection input 75 P62 HREC Input Main unit REC key operation detection input 76* P63 RTCCE Output Clock IC chip enable control output 77* P64 RTCWR Output Clock IC read/write control output 78 P65 CEDT In/Output Clock/EEPROM serial data input/output 79 P66 CECK Output Clock/EEPROM serial data input/output 80 P67 EPCS Output EEPROM chip selection output 81 VDD VDD Output Positive power supply 82 T15 SPIN Inout Spindle motor FG pulse detection input 83* P101 P101 Output Spare for sled motor control 84* P102 TEST0 Input Test mode setting input 0 85* P103 TEST1 Input Test mode setting input 1 86 P30 PSLINN Output Built-in battery power selection output 87 P31 PSLDCI Output DC jack power selection output 88 P32 PSLDRY Output Dry cell power selection output 89* P33 P33 Output Spare for sled motor control 90 P34 ELON Output Remote controller EL light control output 91 T100 CIN Input Truck cross signal detection input 92 P36 PHOLD Output Dry cell power ON holding output 93 P37 PCNT1 Output Power IC VREF feed control output 94 TEST/VPP VPP Output Test/R-ROM write power input 95 P90 PCNT2 Output Power IC VCC feed control output 96 P91 CKSTP Output Main clock stop control output 97 P92 DISCIN Input Disk insertion detection input 98 P93 INNSW Input Mechanism inner SW position detection input 99 P94 DISCPR Input Record enable/disable switch detection input 100 P95 PDCNT Output PD current control output for inner detection IC401 RH-iX2680AF03(IX2680AF):System Microcomputer (2/2) Pin No. Function Port Name Terminal Name Input/Output In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

PARTS GUIDE NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP Capacitors VCC ....................... Ceramic type VCK........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ............... Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) If there are no indications for the electrolytic capacitors, error is ±20%. Resistors VRD ....................... Carbon-film type VRS........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for other parts, the resistors are ±5% carbon-film type. MD-MS701H MD-MS702H(BL) MD-MS702H(GY) MODEL

L171 RCILC0333AFZZ J AC 10 µH,Choke L201 VPBNNR47M0000 J AC 0.47 µH L202 VPBNN100M0000 J AC 10 µH L204 RCILC0353AFZZ J AB Tip Impeder L452 RCILC0352AFZZ J AB Tip Impeder L453,454 RCILC0290AFZZ J AC Tip Solid Induction,200mA L456 RCILC0290AFZZ J AC Tip Solid Induction,200mA L457,458 RCILC0290AFZZ J AC Tip Solid Induction,200mA L491 VPBNN4R7M0000 J AC 4.7 µH L500 VPANM4R7J0000 J AC 4.7 µH L600 RCILC0331AFZZ J AC 2.2 µH,Choke L601~604 RCILR0559AFZZ J AC 47 µH L608 RCILC0246AFZZ J AC 100 µH,Choke L609,610 RCILR0559AFZZ J AC 47 µH L651 VPBNNR47M0000 J AC 0.47 µH L702,703 RCILC0290AFZZ J AC Tip Solid Induction,200mA L704 RCILC0352AFZZ J AB Tip Impeder L710 VPBNNR47M0000 J AC 0.47 µH L711 RCILC0352AFZZ J AB Tip Impeder L712,713 RCILC0290AFZZ J AC Tip Solid Induction,200mA L714 RCILC0290AFZZ J AC Tip Solid Induction,200mA L751,752 RCILC0344AFZZ J AC 47 µH,Choke L771 RCILR0559AFZZ J AC 47 µH L772 VPANM4R7J0000 J AC 4.7 µH L801 RCILC0330AFZZ J AC 1 µH,Choke L821 RCILC0332AFZZ J AC 4.7 µH,Choke L822 RCILC0333AFZZ J AC 10 µH,Choke L841 RCILC0332AFZZ J AC 4.7 µH,Choke L842 RCILC0333AFZZ J AC 10 µH,Choke L862 RCILR0559AFZZ J AC 47 µH L863 RCILC0332AFZZ J AC 4.7 µH,Choke L871 RCILR0559AFZZ J AC 47 µH L886 VPBNNR47M0000 J AC 0.47 µH L887,888 RCORF0112AFZZ J AC Core VIBRATOR XL201 RCRSC0023AFZZ J AK Crystal,33.8688 MHz CAPACITORS C100 VCSAFA0JJ106M J AD 10 µF,6.3V,Electrolytic,Tantalum C102,103 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C104 VCKYTV1EB273K J AB 0.027 µF,25V C106 RC-KZ1189AFZZ J AC 0.22 µF,16V,Electrolytic C107 VCKYTV1EB123K J AB 0.012 µF,25V C109 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C110 RC-KZ1189AFZZ J AC 0.22 µF,16V,Electrolytic C111 VCKYCY1HB332K J AA 0.0033 µF,50V C112 VCKYCY1CB333K J AA 0.033 µF,16V C121,122 VCCCCY1HH271J J AA 270 pF (CH),50V C123,124 VCCSCY1HL391J J AA 390 pF,50V C130 VCKYTV1CB104K J AA 0.1 µF,16V C131 VCCCCY1HH331J J AA 330 pF (CH),50V C161 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C165 VCKYCY1CB333K J AA 0.033 µF,16V C171,172 VCSAFB0JJ336M J AE 33 µF,6.3V,Electrolytic,Tantalum C201 VCKYTV1CF105Z J AB 1 µF,16V C202 VCSAFA0JJ106M J AD 10 µF,6.3V,Electrolytic,Tantalum C203 VCKYCY1CB104K J AB 0.1 µF,16V C205 VCKYCY1CB104K J AB 0.1 µF,16V C207 VCKYCY1CB104K J AB 0.1 µF,16V C211,212 VCCCCY1HH5R0C J AA 5 pF (CH),50V C351 VCCCCY1HH101J J AA 100 pF (CH),50V C353 VCSAFA0JJ106M J AD 10 µF,6.3V,Electrolytic,Tantalum C354 VCKYCY1CB104K J AB 0.1 µF,16V C357 VCKYCY1CB104K J AB 0.1 µF,16V C361 VCKYTV1HB393K J AB 0.039 µF,50V C401 VCKYCY1CB104K J AB 0.1 µF,16V C431 VCKYCY1CB473K J AA 0.047 µF,16V C441 VCCCCY1HH100D J AA 10 pF (CH),50V C442 VCKYCY1HB681K J AA 680 pF,50V C443 RC-KZ1191AFZZ J AC 0.47 µF,10V,Electrolytic C451 VCKYCY1HB102K J AA 1000 pF,50V C481 VCKYCY1CB104K J AB 0.1 µF,16V C491 VCKYTV1CB104K J AA 0.1 µF,16V C500 VCSAFA0JJ106M J AD 10 µF,6.3V,Electrolytic,Tantalum C501,502 VCKYCY1HB222K J AA 0.0022 µF,50V C503,504 VCSAFA1AJ335M J AD 3.3 µF,10V C507 VCSAFA0JJ106M J AD 10 µF,6.3V,Electrolytic,Tantalum C508 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C509,510 VCKYTV1CF225Z J AC 2.2 µF,16V INTEGRATED CIRCUITS IC101 VHIIR3R55//-1 J AQ RF Signal,Processor,IR3R55 IC201 VHILR37648B-1 J BD ENDEC,LR37648B IC202 RH-IX2567AFZZ J BA 4M D-RAM,IX2567AF IC351 VHI74ACT02F-1 J AF Head Driver,74ACT02F IC401 RH-IX2680AF03 J AX System Microcomputer, IX2680AF IC402 VHIS29L294A-1 J AH E2-PROM,S29L294A IC404 VHI7SH00FU/-1 J AE NAND Gate,7SH00FU IC431 VHIS80821LN-1 J AE 2.1V Reset,S80821LN IC441 VHITC7W14FU-1 J AF Inverter,TC7W14FU IC501 VHIAK4514VF-1 J AT AD/DA Converter,AK4514VF IC601 VHIMPC17A39-1 J AQ Pickup Coil Driver,MPC17439 IC651 VHILB1638M/-1 J AH Motor Drive,LB1638M IC701 VHIIR3R54N/-1 J AQ Audio Amp.,IR3R54N IC702 VHITK71345M-1 J AE 4.5V Regulator (ON/OFF), TK71354M IC703 VHIIR3R54N/-1 J AQ Audio Amp.,IR3R54N IC771 VHITK71225M-1 J AE 2.5V Regulator,TK71225M IC800 VHIHN1C03FU-1 J AD Voltage Regulator,HN1C03FU IC801 VHIHAT1025R-1 J AK Power Select,HAT1025R IC803 VHINDH831N/-1 J AH N-ch MOS FET,NDH831N IC804 VHIRN4904//-1 J AD Power Select Charge Drive, RN4904 IC805 VHIUMD3N///-1 J AC Constant Current Drive,UMD3N IC821 VHIIR3M09N/-1 J AL Power Drive,IR3M09N IC841 VHIIR3M09N/-1 J AL Power Drive,IR3M09N IC871 VHIS8327B30-1 J AG 3V DC/DC Converter,S8327B30 IC872 VHITC7W32FU-1 J AE C-MOS Logic,TC7W32FU IC873 VHIS80827LN-1 J AE 2.7V Reset,S80827LN IC874 VHITC7S00FU-1 J AD Charge Drive,TC7S00FU IC875 VHITK71325M-1 J AE 2.5V Regulator (ON/OFF), TK71325M IC876 VHIRN4904//-1 J AD Power Select Charge Drive, RN4904 IC901 VHIBA6965FV-1 J AN Spindle Motor Driver,BA6965FV TRANSISTORS Q101 VS2SA17457/-1 J AB Silicon,PNP,2SA17457 Q351 VS2SK2909//-1 J AE FET,2SK2909 Q352 VS2SK2911//-1 J AE FET,2SK2911 Q353 VS2SK2909//-1 J AE FET,2SK2909 Q354 VS2SK2911//-1 J AE FET,2SK2911 Q401 VS2SA17457/-1 J AB Silicon,PNP,2SA17457 Q711 VSRN1444A//-1 J AC Digital,NPN,RN1444 A Q721 VS2SC4213B/-1 J AC Silicon,NPN,2SC4213 B Q801 VS2SD1950//-1 J AD Silicon,NPN,2SD1950 Q802,803 VSDTC144EE/-1 J AB Digital,NPN,DTC144 EE Q822 VHINDS335N/-1 J AF FET,NDS335N Q842 VHINDS3335N/-1 J AF FET,NDS335N Q871 VHINDS335N/-1 J AF FET,NDS335N Q872 VSDTC144EE/-1 J AB Digital,NPN,DTC144 EE Q873 VS2SJ305///-1 J AF FET,2SJ305 DIODES D201 VHD1SS369//-1 J AD Silicon,1SS369 D351,352 VHDSB0209CP-1 J AC Silicon,SB0209CP D431 VHD1SS361//-1 J AB Silicon,1SS361 D491~493 VHE015Z5R1Y-1 J AD Zener,5.1V,015Z5.1Y D494 VHE15AZ7R5Y-1 J AC Zener,7.5V,15AZ7.5Y D800 VHDRB491D//-1 J AD Silicon,RB491D D801 VHE015Z5R1Y-1 J AD Zener,5.1V,015Z5.1Y D802 VHDSB10015C-1 J AD Silicon,SB10015C D821 VHDF1J2F///-1 J AE Silicon,F1J2F D822 VHDRB521S30-1 J AC Silicon,RB521S30 D831 VHD1SS372//-1 J AD Silicon,1SS372 D841 VHDF1J2F///-1 J AE Silicon,F1J2F D842 VHDRB521S30-1 J AC Silicon,RB521S30 D861 VHDRB491D//-1 J AD Silicon,RB491D D862 VHDRB521S30-1 J AC Silicon,RB521S30 D871 VHDRB491D//-1 J AD Silicon,RB491D D873 VHD1SS372//-1 J AD Silicon,1SS372 D875 VHD1SS378//-1 J AC Silicon,1SS378 D877 VHD1SS360//-1 J AB Silicon,1SS360 PH901 VHPGP1S93K/-1 J AF Photo Interrupter,GP1S93K COILS L100 VPBNN100M0000 J AC 10 µH

C713,714 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C715 VCKYCY1CB104K J AB 0.1 µF,16V C721,722 VCSAFA1AJ335M J AD 3.3 µF,10V C723,724 VCKYCY1HB102K J AA 1000 pF,50V C725,726 VCSAFA1AJ335M J AD 3.3 µF,10V C727 VCKYTV1CF105Z J AB 1 µF,16V C731 VCKYCY1CF224Z J AB 0.22 µF,16V C733,734 VCKYTV1CB104K J AA 0.1 µF,16V C735 VCKYCY1HB102K J AA 1000 pF,50V C736 VCKYCY1EB103K J AA 0.01 µF,25V C751,752 VCKYTV1EB823K J AB 0.082 µF,25V C753,754 VCKYTV1CF105Z J AB 1 µF,16V C755 VCKYCY1EB103K J AA 0.01 µF,25V C756,757 VCKYTV1AB684K J AC 0.68 µF,10V C758 VCSAFA1AJ335M J AD 3.3 µF,10V C759 VCKYCY1CB563K J AB 0.056 µF,16V C761,762 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C767,768 RC-KZ1189AFZZ J AC 0.22 µF,16V,Electrolytic C771,772 VCSAFB0JJ336M J AE 33 µF,6.3V,Electrolytic,Tantalum C773 RC-KZ1189AFZZ J AC 0.22 µF,16V,Electrolytic C774 VCKYTV1CF105Z J AB 1 µF,16V C775 VCKYCY1EB103K J AA 0.01 µF,25V C802 VCKYTV1CF105Z J AB 1 µF,16V C803 VCKYTV1CB104K J AA 0.1 µF,16V C804 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C805 VCEAPW0JW107M J AD 100 µF,6.3V,Electrolytic C806 RC-KZ1216AFZZ J AD 3.3 µF,10V,Electrolytic C807 VCKYTV1CB104K J AA 0.1 µF,16V C808 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C810 RC-KZ1190AFZZ J AC 0.33 µF,10V,Electrolytic C821 VCEAPW0GW227M J AD 220 µF,4.0V,Electrolytic C822 VCCCCY1HH390J J AA 39 pF (CH),50V C823,824 VCCCCY1HH101J J AA 100 pF (CH),50V C825 VCCCCY1HH680J J AA 68 pF (CH),50V C826 RC-KZ1198AFZZ J AC 1 µF,10V,Electrolytic C827 RC-KZ1216AFZZ J AD 3.3 µF,10V,Electrolytic C828 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C829 VCKYCY1EB103K J AA 0.01 µF,25V C830 VCKYCY1HB102K J AA 1000 pF,50V C831,832 VCKYCY1CB104K J AB 0.1 µF,16V C842 VCCCCY1HH220J J AA 22 pF (CH),50V C843,844 VCCCCY1HH101J J AA 100 pF (CH),50V C845 VCCCCY1HH470J J AA 47 pF (CH),50V C846 RC-KZ1198AFZZ J AC 1 µF,10V,Electrolytic C847 RC-KZ1217AFZZ J AE 10 µF,10V,Electrolytic C848 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C849 VCKYCY1EB103K J AA 0.01 µF,25V C850 VCKYCY1HB102K J AA 1000 pF,50V C863 RC-KZ1198AFZZ J AC 1 µF,10V,Electrolytic C864 VCSAFB0JJ336M J AE 33 µF,6.3V,Electrolytic,Tantalum C865,866 RC-KZ1198AFZZ J AC 1 µF,10V,Electrolytic C868 VCKYTV1CF105Z J AB 1 µF,16V C869 VCSAFB0JJ336M J AE 33 µF,6.3V,Electrolytic,Tantalum C871,872 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C873 VCKYTV1CF105Z J AB 1 µF,16V C874 VCSAFA1AJ106M J AD 10 µF,10V,Electrolytic,Tantalum C875 RC-KZ1189AFZZ J AC 0.22 µF,16V,Electrolytic C877 VCSAFA0JJ106M J AD 10 µF,6.3V,Electrolytic,Tantalum C878 RC-KZ1216AFZZ J AD 3.3 µF,10V,Electrolytic C879 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C880 VCKYCY1EB103K J AA 0.01 µF,25V C881 RC-KZ1193AFZZ J AC 1 µF,6.3V,Electrolytic C886 VCSAFA1AJ106M J AD 10 µF,10V,Electrolytic,Tantalum C902 VCKYCY1EB103K J AA 0.01 µF,25V C903 RC-KZ1216AFZZ J AD 3.3 µF,10V,Electrolytic C905~907 VCKYCY1HB222K J AA 0.0022 µF,50V C908 RC-KZ1191AFZZ J AC 0.47 µF,10V,Electrolytic C909,910 VCKYCY1CB473K J AA 0.047 µF,16V C911 VCKYCY1CB104K J AB 0.1 µF,16V C951,952 VCSAFE0GJ476M J AE 47 µF,4.0V,Electrolytic,Tantalum RESISTORS VRS-CY1JB000J J AA 0 ohm,Jumper,0.8×1.55mm, Green VRS-TV2AB000J J AA 0 ohm,Jumper,1.25×2mm,Green R101~104 VRS-CY1JB223J J AA 22 kohms,1/16W R105 VRS-CY1JB394J J AA 390 kohms,1/16W R106 VRS-CY1JB563J J AA 56 kohms,1/16W R154 VRS-CY1JB122J J AA 1.2 kohms,1/16W R161 VRS-CY1JB122J J AA 1.2 kohms,1/16W R203 VRS-CY1JB101J J AA 100 ohm,1/16W R204 VRS-CY1JB102J J AA 1 kohm,1/16W R205 VRS-CY1JB564D J AA 560 kohms,1/16W R206 VRS-CY1JB224D J AA 220 kohms,1/16W R207 VRS-CY1JB681J J AA 680 ohms,1/16W R222 VRS-CY1JB105J J AA 1 Mohm,1/16W R361 VRS-TQ2BB8R2J J AB 8.2 ohms,1/8W R400 VRS-CY1JB392J J AA 3.9 kohms,1/16W R402 VRS-CY1JB103J J AA 10 kohm,1/16W R403 VRS-CY1JB223J J AA 22 kohms,1/16W R404 VRS-CY1JB154J J AA 150 kohms,1/16W R405 VRS-CY1JB103J J AA 10 kohm,1/16W R406 VRS-CY1JB104J J AA 100 kohm,1/16W R407 VRS-CY1JB103J J AA 10 kohm,1/16W R408,409 VRS-CY1JB104J J AA 100 kohm,1/16W R411 VRS-CY1JB104J J AA 100 kohm,1/16W R412 VRS-CY1JB103J J AA 10 kohm,1/16W R413~415 VRS-CY1JB102J J AA 1 kohm,1/16W R419,420 VRS-CY1JB102J J AA 1 kohm,1/16W R421 VRS-CY1JB104J J AA 100 kohm,1/16W R422 VRS-CY1JB333J J AA 33 kohms,1/16W R423 VRS-CY1JB223D J AA 22 kohms,1/16W R424,425 VRS-CY1JB223J J AA 22 kohms,1/16W R426 VRS-CY1JB104J J AA 100 kohm,1/16W R431 VRS-CY1JB334J J AA 330 kohms,1/16W R441 VRS-CY1JB123J J AA 12 kohms,1/16W R442 VRS-CY1JB104J J AA 100 kohm,1/16W R443 VRS-CY1JB393J J AA 39 kohms,1/16W R444 VRS-CY1JB272J J AA 2.7 kohms,1/16W R451 VRS-CY1JB562J J AA 5.6 kohms,1/16W R452 VRS-CY1JB822J J AA 8.2 kohms,1/16W R453 VRS-CY1JB183J J AA 18 kohms,1/16W R454 VRS-CY1JB563J J AA 56 kohms,1/16W R455 VRS-CY1JB562J J AA 5.6 kohms,1/16W R456 VRS-CY1JB822J J AA 8.2 kohms,1/16W R457 VRS-CY1JB183J J AA 18 kohms,1/16W R458 VRS-CY1JB563J J AA 56 kohms,1/16W R481 VRS-CY1JB363D J AA 36 kohms,1/16W R482 VRS-CY1JB183D J AA 18 kohms,1/16W R492 VRS-CY1JB102J J AA 1 kohm,1/16W R500 VRS-CY1JB4R7J J AA 4.7 ohms,1/16W R501,502 VRS-CY1JB471J J AA 470 ohms,1/16W R503,504 VRS-CY1JB203J J AA 20 kohms,1/16W R601 VRS-CY1JB563J J AA 56 kohms,1/16W R701,702 VRS-CY1JB101J J AA 100 ohm,1/16W R703 VRS-CY1JB154J J AA 150 kohms,1/16W R711,712 VRS-CY1JB562J J AA 5.6 kohms,1/16W R713,714 VRS-CY1JB103J J AA 10 kohm,1/16W R715,716 VRS-CY1JB104J J AA 100 kohm,1/16W R717 VRS-CY1JB102J J AA 1 kohm,1/16W R719,720 VRS-CY1JB822J J AA 8.2 kohms,1/16W R723,724 VRS-CY1JB682J J AA 6.8 kohms,1/16W R725 VRS-CY1JB101J J AA 100 ohm,1/16W R726 VRS-CY1JB393J J AA 39 kohms,1/16W R727 VRS-CY1JB103J J AA 10 kohm,1/16W R728 VRS-CY1JB102J J AA 1 kohm,1/16W R729,730 VRS-CY1JB272J J AA 2.7 kohms,1/16W R751,752 VRS-CY1JB820J J AA 82 ohms,1/16W R753 VRS-CY1JB154J J AA 150 kohms,1/16W R754 VRS-CY1JB334J J AA 330 kohms,1/16W R756,757 VRS-CY1JB273J J AA 27 kohms,1/16W R761,762 VRS-CY1JB332J J AA 3.3 kohms,1/16W R765,766 VRS-CY1JB150J J AB 15 ohms,1/16W R767,768 VRS-CY1JB102J J AA 1 kohm,1/16W R801 VRS-CY1JB684D J AA 680 kohms,1/16W R802 VRS-CY1JB394D J AA 390 kohms,1/16W R803,804 VRS-CY1JB104J J AA 100 kohm,1/16W R805 VRS-CY1JB474D J AA 470 kohms,1/16W R806 VRS-CY1JB684D J AA 680 kohms,1/16W R807 VRS-CY1JB273D J AA 27 kohms,1/16W R808 VRS-CY1JB393D J AA 39 kohms,1/16W R809 VRS-CY1JB104J J AA 100 kohm,1/16W – 2 –

CN101 QCNCW801XAFZZ J AH Socket,22Pin CN451 QCNCW749PAFZZ J AE Socket,14Pin CN482 QCNCW804GAFZZ J AD Socket,7Pin CN601 QCNCW804RAFZZ J AE Socket,16Pin CN701 QCNCWWQ33AFZZ J AE Socket,33Pin J701 VHPGP1FB65R-1 J AP Jack,LINE J702 QJAKM0189AFZZ J AE Jack,MIC IN J703 QJAKM0201AFZZ J AH Jack,Headphones J801 QJAKC0136AFZZ J AD Jack,DC IN M901 RMOTV0500AFZZ J AT Motor Ass’y [Spindle] M902 RMOTV0503AFZZ J AF Motor Ass’y [Sled] M903 RMOTV0501AFM1 J AS Motor Ass’y [Lift] SW401 QSW-M0171AFZZ J AC Switch,Push Type [EJECT] SW402 QSW-S0948AFZZ J AC Switch,Slide Type [HOLD] SW901 QSW-M0169AFZZ J AD Switch,Push Type [Disc In] SW902 QSW-M0170AFZZ J AD Switch,Push Type [Disc Protect] MECHANICAL PARTS 1 NGERH0597AFZZ J AC Wheel,Drive 2 NSFTD0328AFZZ J AE Screw,Drive 3 LHLDX3136AFM1 J AH Cartridge Holder Ass’y 4 MSPRT1607AFFJ J AB Spring,Cancel Lever 5 MLEVF2598AFFW J AD Lever,Eject 6 LCHSM0931AFM1 J AN Main Chassis Ass’y 7 PCUSG0599AFZZ J AB Cushion 8 QPWBH0306AFM1 J AQ Mechanism Flexible PWB Ass’y 8- 1 ———— J — Mechanism Flexible PWB (Not Replacement Item) 8- 2(SW901) QSW-M0169AFZZ J AD Switch,Push Type [Disc In] 8- 3(SW902) QSW-M0170AFZZ J AD Switch,Push Type [Disc Protect] 8- 4(PH901) VHPGP1S93K/-1 J AF Photo Interrupter,GP1S93K 11 MSPRP0881AFFJ J AB Spring, 13 NGERH0596AFZZ J AD Gear,Drive 15 RCTRH8175AFZZ J BM Optical Pickup Unit 16 MSPRP0880AFFJ J AC Spring,Drive Grip 18 NSFTM0292AFFW J AC Shaft,Guide 20 MSPRT1604AFFJ J AB Spring,Eject Lever 23 QPWBH0307AFZZ J AF Magnetic Head Flexible PWB 25 MLEVF2599AFM1 J AE Lift Lever Ass’y 26 NGERH0595AFZZ J AC Gear,Lift Drive 28 MLEVF2600AFFW J AD Lever,Lift 29 MSPRD1353AFFJ J AB Spring,Lift Lever 30 LANGF1588AFFW J AD Bracket,Pickup 32 RCILH0109AFZZ J AN Magnetic Head 501 XSPSN14P01800 J AA Screw,ø1.4×1.8mm 502 LX-JZ0154AFZZ J AA Screw,ø1.4×2.8mm 503 LX-BZ0823AFZZ J AA Screw,ø1.4×1.2mm 504 LX-WZ9290AFZZ J AA Washer,ø0.8×ø2.4×0.25mm 505 LX-BZ0800AFZZ J AA Screw,ø1.4×2.5mm 506 LX-JZ0146AFZZ J AA Screw,ø1.7×2.5mm 507 LX-BZ0804AFFF J AA Screw,ø1.4×2.2mm 508 LX-BZ0960AFZZ J AB Screw,ø1.4×1.5mm 509 XSPSN14P01200 J AA Screw,ø1.4×1.2mm 510 LX-WZ9164AFZZ J AA Washer,ø1×ø2.4×0.25mm 511 LX-BZ0959AFZZ J AB Screw,ø1.4×1.8mm 512 LX-WZ9293AFZZ J AA Washer,ø2.7×ø5×0.25mm 513 LX-WZ9294AFZZ J AA Washer,ø1×ø2.4×0.15mm M901 RMOTV0500AFZZ J AT Motor Ass’y [Spindle] M902 RMOTV0503AFZZ J AF Motor Ass’y [Sled] M903 RMOTV0501AFM1 J AS Motor Ass’y [Lift] CABINET PARTS 201 GCABB2841AFSB J AG Front Cabinet [702H GY] 201 GCABB2841AFSC J AG Front Cabinet [701H] 201 GCABB2841AFSG J AG Front Cabinet [702H BL] 202 CCABD4342AF01 J AX Bottom Cabinet Ass’y [702H GY] 202 CCABD4342AF03 J AX Bottom Cabinet Ass’y [702H BL] 202 CCABD4352AF01 J AX Bottom Cabinet Ass’y [701H] 202- 1 ———— — Bottom Cabinet (Not Replacement Item) 202- 2 GCOVA2218AFSA J AB Cover,DC Jack 202- 3 JKNBZ2040AFSA J AD Knob,HOLD 202- 4 PSHET0371AFZZ J AC Sheet,Bottom Cabinet 203 GFTAB1348AFSA J AC Lid,Battery [701H] 203 GFTAB1348AFSB J AC Lid,Battery [702H GY] 203 GFTAB1348AFSG J AF Lid,Battery [702H BL] 205 GCOVA2217AFSA J AD Cover,Eject [701H] 205 GCOVA2217AFSB J AD Cover,EJECT [702H GY] 205 GCOVA2217AFSF J AD Cover,EJECT [702H BL] 206 QTANZ9150AFFQ J AC Battery Terminal,- 207 QTANZ9149AFFQ J AC Battery Terminal,+ 208 JKNBK0526AFSA J AE Knob,Eject 209 LANGK0934AFM1 J AN Main Frame Ass’y 210 PCUSG0649AFZZ J AB Cushion Machanism 211 PSHET0373AFZZ J AC Sheet 213 LANGZ0334AFM1 J AN Eject Bracket Ass’y 214 PCUSG0635AFZZ J AA Rubber,Preventive Vibration B 215 PCUSG0636AFZZ J AA Rubber,Preventive Vibration C 216 GCABA2839AFSA J AF Center Cabinet [701H] 216 GCABA2839AFSB J AF Center Cabinet [702H GY] 216 GCABA2839AFSF J AF Center Cabinet [702H BL] 217 PCUSG0534AFZZ J AC Rubber,Preventive Vibration 219 PSHET0378AFZZ J AB Sheet,Extention Battery Terminal 220 QTANZ9151AFFQ J AG Extention Battery Terminal 221 CCABC4329AF01 J AY Top Cabinet Ass’y [701H] 221 CCABC4330AF01 J AZ Top Cabinet Ass’y [702H GY] 221 CCABC4330AF05 J BA Top Cabinet Ass’y [702H BL] 221- 1 ———— — Top Cabinet 221- 2 HDECQ0528AFSA J AG Transparent Plate [701H] 221- 2 HDECQ0533AFSA J AG Transparent Plate [702H] 221- 3 HDECQ0529AFSA J AM Decoration Plate [701H] 221- 3 HDECQ0529AFSB J AM Decoration Plate [702H] 221- 4 PSHEZ0817AFZZ J AC Sheet,Transparent Plate 221- 5 PSHEZ0818AFZZ J AC Sheet,Decoration Plate 226 LANGK0935AFFW J AH Bracket,Knob 227 LHLDZ1706AFZZ J AD Holder,LCD 228 PCUSG0648AFZZ J AB Cushion,LCD 229 PCUSG0651AFZZ J AB Cushion,Bracket 231 RUNTK0442AFZZ J AP Key Flexible PWB Ass’y 232 RUNTZ0655AFZZ J AZ LCD 233 JKNBZ2042AFSA J AK Knob,Operation A [701H] 233 JKNBZ2042AFSB J AF Knob,Oparetion A [702H] 234 JKNBZ2043AFSA J AE Knob,Operation D [701H] 234 JKNBZ2047AFSA J AG Knob,Operation D [702H GY] 234 JKNBZ2047AFSB J AH Knob,Operation D [702H BL] 235 JKNBZ2044AFSA J AC Knob,Operation B 236 JKNBZ2045AFSA J AC Knob,REC [701H] 236 JKNBZ2048AFSA J AC Knob,REC [702H] 237 PCUSG0637AFZZ J AB Cushion A 238 PCUSG0652AFZZ J AB Cushion,Bracket – 3 –

242 HDECQ0530AFSA J AL Decoration Ring [702H GY] 242 HDECQ0530AFSB J AN Decoration Ring [702H BL] 244 PCUSG0646AFZZ J AB Cushion,Jack 245 PCUSG0649AFZZ J AB Cushion,Switch 246 PSHEZ0851AFZZ J AC Bracket,Eject Knob 247 PCUSG0646AFZZ J AB Rubber,Prevention Vibration 248 GFTAC3135AFSA J AG Cover,MD 249 LANGZ0335AFFW J AB Bracket,Disc Guide 250 PCUSG0638AFZZ J AA Rubber,Prevention Vibration D 251 PGIDM0256AFSA J AB Guide (Left) 253 PCUSG0647AFZZ J AB Cushion DC 254 QPWBH0308AFZZ J AE Audio Flexible PWB 255 PSPAZ0532AFZZ J AC Mechanism Spacer 256 PSHET0382AFZZ J AB Sheet,Jack 257 TLABS0465AFZZ J AB Label,Laser Mark 258 TLABS0497AFZZ J Label,Laser Caution 601 LX-BZ0908AFF3 J AA Screw,ø1.4×2.0mm 603 LX-CZ0107AFFF J AA Screw,ø1.2×2.5mm 605 LX-CZ0126AFFF J AA Screw,ø1.4×2.0mm 606 LX-BZ0877AFF3 J AA Screw,ø1.4×1.5mm 608 LX-BZ0805AFFN J AB Screw,ø1.7×2.5mm 610 LX-BZ0908AFFC J AB Screw,ø1.4×2mm ACCESSORIES/PACKING PARTS 1 SPAKZ0475AFZZ J Pad,Operation Manual 2 QCNWG0382AFZZ J AK Connecting Cord,RCA Type 3 RADPA7407AFZZ J BF AC Adaptor [For Europe] 3 RADPA8404AFZZ J BK AC Adaptor [For UK] 4 RPHOH0176AFZZ J AR Headphones 5 RRMCW0024AFZZ J BB Remote Control 6 SPAKA2679AFZZ J AD Packing Add. 7 SPAKC6529AFZZ J AL Packing Case [702H GY] 7 SPAKC6530AFZZ J Packing Case [702H BL] 7 SPAKC6552AFZZ J Packing Case [701H] 8 SSAKH0314AFZZ J AD Polyethylene Bag,Unit 9 TCADS0085AFZZ J AD Service Card [For UK Only] 10 SPAKZ0479AFZZ J Sheet 11 TINSE1633AFZZ J AH Operation Manual [For UK] 11 TINSZ1336AFZZ J AR Operation Manual [For Europe] 12 TLABM0592AFZZ J AD Label,Feature 13 SPAKZ0465AFZZ J Pad,AC Adaptor 14 UBAGC0076AFSA J AH Carrying Bag 15 UBATI0060AFSA J BH Rechargeable,Battery P.W.B. ASSEMBLY (Not Replacement Item) PWB-A1,2 DCYO-3035AF93 J –– Main/Jack (Combined Ass’y) OTHER SERVICE PARTS QCNWK0110AFZZ J Flat Cable for Service,16Pin RUNTK0460AFZZ J Extention Connector Unit for Service,16Pin UDSKM0001AFZZ J AZ Recording Mini Disc 88GMMD-110 J BV High Reflection,MMD-110 (TEAC Test MD) 88GMMD-212 J BU Low Reflection,MMD-212 (TEAC Test MD) – 4 –

– 5 – 1 2 7 507 3 6 5 20 4 23 30 509 8 8-1 8-3 (SW902) 506 501 506 11 13 504 25 26 29 15 18 16 505 507 510 512 513 513 M903 M902 M901 28 503x2 502 8-2 (SW901) 8-4 32 511x2 508

– 6 – MD Mechanism MS702H Only 220 216 209 219 247 217 203 606 601 208 211 205 246 213 603 605 215 210 251 606 606 608x2 201 217 217 214 249 250 248 608x2 244 PWB–A2 PWB–A1 207 206 245 254 202 202-4 202-2 202-1 202-3 227 238 601 606 237 226 232 228 239 237 236 233 234 255 235 240 221-1 241x3 221-3 221-5 242 221-4 221-2 221 234 257 258 231 229 610x2 610 610 610x2 610x2 610 610 253 256 MS702H MS701H

UNIT HOLD OFF Remote HOLD CANCEL Control SETTING POSITION OF SWITCHES AND KNOBS 1. QCNMG0382AFZZ Connecting Cord, RCA Type 2. RADPA8404AFZZ AC Adaptor 3. RPHOH0176AFZZ Headphones 4. RRMCW0024AFZZ Remote Control 5. SPAKA2679AFZZ Packing Add. 6. SPAKC6529AFZZ Packing Case [702H GY] 6. SPAKC6530AFZZ Packing Case [702H BL] 6. SPAKC6552AFZZ Packing Case [701H] 7. SSAKH0314AFZZ Polyethylene Bag, Unit 8. TCADS0085AFZZ Service Card 9. TiNSE1633AFZZ Operation Manual 10. TLABM0592AFZZ Label, Feature [701 Only] 11. SPAKZ0465AFZZ Pad, AC Adaptor 12. UBAGC0076AFSA Carrying Bag 13. UBATi0060AFSA Rechargeable, Battery 14. SPAKZ0475AFZZ Pad, Operation Manual 15. SPAKZ0479AFZZ Sheet – 7 – COPYRIGHT 1997 BY SHARP COPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. A9711-2895NS•HA•J SG • SK SHARP CORPORATION Audio-Visual Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-01, Japan Printed in U.K. © 2 3 4 13 6 5 11 1 9 14 8 12 7 15 10 MD-MS701H