Snapper 421620BVE Manual 

INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.4. PARK BRAKE 1. Engage park brake by pushing clutch/brake pedal "DOWN" and moving the park brake lever to the "ON" position. While holding the park brake lever "ON", release clutch/brake pedal to set park brake. See Figure 2.16. TO APPLY BRAKES, PUSH CLUTCH/BRAKE PEDAL _ ALL THE WAY DOWN. 2.5. CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height as desired to any one of six positions using deck lift lever. When in desired height of cut, release latch, then try to move deck lift lever to ensure lift lever latch is f ...

& REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage. DO NOT attempt to service or charge the battery while it is installed on the machine. RED POSITIVE (+) BLACK NEGATIVE (-) CABLE POSITIVE TERMINAL INSULATOR 4.6 BATTERY ...

INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.4. PARK BRAKE 1. Engage park brake by pushing clutch/brake pedal "DOWN" and moving the park brake lever to the "ON" position. While holding the park brake lever "ON", release clutch/brake pedal to set park brake. See Figure 2.16. TO APPLY BRAKES, PUSH CLUTCH/BRAKE PEDAL _ ALL THE WAY DOWN. 2.5. CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height as desired to any one of six positions using deck lift lever. When in desired height of cut, release latch, then try to move deck lift lever to ensure lift lever latch is f ...

In a dishwashlng detergent and water solution. Rinse and wring dry, then saturate with oil and squeeze out excess. Failure to re-oil this type filter will ruin the engine. Clean paper elements by tapping lightly. Blowing with air will rupture paper elements. Use a flashlight to detect clogged or torn paper elements - replace If damaged in any way. Air is also needed to keep your engine cool. Dirt, dust & debris build up to restrict and clog cooling air Intake screens and fins. Clean screens and fins at frequent Intervals. The engine blower ...

hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity or jud ...

& REPAIR 4.6.6. BATTERY TESTING State of Charge 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charged Battery Condition Chart Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.100 Digital Voltmeter 12.80v 12.60v 12.40v 12.10v 11.90v Less than 11.80v Five Ball Hydrometer Five Balls Floating Four Balls Floating Three Balls Floating Two Balls Floating One Ball Floating Zero Balls Floating SNAPPER REAR ENGINE RIDER ACCESSORIES PART NO. 6-0517 .......................... 6-0601 .......................... 6-0697 .................... ...

INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.4. PARK BRAKE 1. Engage park brake by pushing clutch/brake pedal "DOWN" and moving the park brake lever to the "ON" position. While holding the park brake lever "ON", release clutch/brake pedal to set park brake. See Figure 2.16. TO APPLY BRAKES, PUSH CLUTCH/BRAKE PEDAL _ ALL THE WAY DOWN. 2.5. CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height as desired to any one of six positions using deck lift lever. When in desired height of cut, release latch, then try to move deck lift lever to ensure lift lever latch is f ...