Sony HBD-E570 Service Manual

Published by Sony Techno Create Corporation HBD-E370/E470/ E570/E870/T57 SPECIFICATIONS BLU-RAY DISC/DVD RECEIVER 9-889-770-01 2010B05-1 © 2010.02 US Model HBD-E370/E570/T57 Canadian Model HBD-E370/E470/E870 AEP Model UK Model HBD-E370/E870 Ver. 1.0 2010.02 • HBD-E370 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-E370. • HBD-E470 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-E470. • HBD-E570 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-E570. • HBD-E870 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-E870. • HBD-T57 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-T57. Model Name Using Similar Mechanism BDP-S370 Mechanism Type BPX-5 Optical Pick-up Block Name KEM-460AAA Photo: HBD-E370 Amplifier Section U.S. models: POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (FTC) Front L + Front R: With 3 ohms loads, both channels driven, from 180 - 20,000 Hz; rated 60 watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 milli watts to rated output. Other models: POWER OUTPUT (rated) Front L/Front R: 108 W + 108 W (at 3 ohms, 1 kHz, 1% THD) HBD-E370: POWER OUTPUT (reference) Front L/Front R/Center/Surround L/Surround R: 142 W (per channel at 3 ohms, 1 kHz) Subwoofer: 140 W (at 3 ohms, 80 Hz) HBD-E870/HBD-E570/HBD-E470/HBD-T57: POWER OUTPUT (reference) Front L/Front R/Center/Surround L/Surround R: 167 W (per channel at 3 ohms, 1 kHz) Subwoofer: 165 W (at 3 ohms, 80 Hz) Inputs (Analog) AUDIO (AUDIO IN) Sensitivity: 450/250 mV Inputs (Digital) SAT/CABLE (COAXIAL), TV (OPTICAL) Supported formats: LPCM 2CH (up to 48 kHz), Dolby Digital, DTS Video Section Outputs VIDEO: 1 Vp-p 75 ohms COMPONENT: Y: 1 Vp-p 75 ohms PB/CB, PR/CR: 0.7 Vp-p 75 ohms HDMI OUT: Type A (19 pin) BD/DVD/Super Audio CD/CD System Signal format system NTSC (US and USB Section (USB) port: Type A (For connecting USB memory, memory card reader, digital still camera, and digital video camera) Maximum current: 500 mA LAN Section LAN (100) terminal 100BASE-TX Terminal Tuner Section System PLL quartz-locked digital synthesizer FM tuner section Tuning range North American models: 87.5 MHz - 108.0 MHz (100 kHz step) Other models: 87.5 MHz - 108.0 MHz (50 kHz step) Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz General Power requirements North American model: 120 V AC, 60 Hz Other models: 50/60 Hz Power consumption On: 170 W Standby: 0.3 W (at the Power Saving mode) Dimensions (approx.) 430 mm × 85 mm × 335 mm (17 in × 3 3/8 in × 13 1/4 in) (w/h/d) incl. projecting parts Mass (approx.) 4.8 kg (10 lb 10 oz) Design and specifications are subject to change without notice. Canadian models) PAL/NTSC (AEP and UK models) 220 - 240 V AC, www. xiaoyu163. com QQ 376315150 92498299 8 TEL 13942296513 Q 376315150 892498299 Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com http://www.xiaoyu163.com

• Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be dam- aged by heat. FLEXIBLE CIRCUIT BOARD REPAIRING • Keep the temperature of soldering iron around 270 °C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) 1.5 kΩ 0.15 μF AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. • This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. • This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive matrix surround decoder and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Labora- tories. ** Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved. • This system incorporates High-Defi nition Multimedia Interface (HDMI™) tech- nology. HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. • Java and all Java-based trademarks and logos are trademarks or registered trade- marks of Sun Microsystems, Inc. • “BD-LIVE” and “BONUSVIEW” are trademarks of Blu-ray Disc Association. • “Blu-ray Disc” is a trademark. • “Blu-ray Disc,” “DVD+RW,” “DVD-RW,” “DVD+R,” “DVD-R,” “DVD VIDEO,” and “CD” logos are trademarks. • “BRAVIA” is a trademark of Sony Corporation. • “AVCHD” and the “AVCHD” logo are trademarks of Matsushita Electric Indus- trial Co., Ltd. and Sony Corporation. • “S-AIR” and its logo are trademarks of Sony Corporation. • , “XMB,” and “xross media bar” are trademarks of Sony Corporation and Sony Computer Entertainment Inc. • “PLAYSTATION” is a trademark of Sony Computer Entertainment Inc. • DivX®, DivX Certifi ed® and associated logos are registered trademarks of DivX, Inc. and are used under license. (Except for U.S. models.) • Music and video recognition technology and related data are provided by Grace- note®. Gracenote is the industry standard in music recognition technology and related content delivery. For more information, please visit www.gracenote.com. CD, DVD, Blu-ray Disc, and music and video-related data from Gracenote, Inc., copyright © 2000-present Gracenote. Gracenote Software, copyright © 2000-present Gracenote. One or more patents owned by Gracenote apply to this product and service. See the Gracenote website for a nonexhaustive list of applicable Gracenote patents. Gracenote, CDDB, MusicID, MediaVOCS, the Gracenote logo and logotype, and the “Powered by Gracenote” logo are either registered trademarks or trademarks of Gracenote in the United States and/or other countries. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radia- tion exposure. www. xiaoyu163. com QQ 376315150 92498299 8 TEL 13942296513 Q 376315150 892498299 Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com http://www.xiaoyu163.com

4 2. DISASSEMBLY 2-1. Disassembly Flow ........................................................... 11 2-2. Case (EZ) ........................................................................ 11 2-3. MB-134 Board ................................................................ 12 2-4. Bracket (MB) Block ........................................................ 13 2-5. Fuse (F901), POWER Board .......................................... 13 2-6. Front Panel Block ........................................................... 14 2-7. CONNECT Board ........................................................... 14 2-8. BD Drive (BPX-5) .......................................................... 15 2-9. Back Panel Block ............................................................ 15 2-10. MAIN Board ................................................................... 16 2-11. AUDIO Board ................................................................. 16 2-12. Optical Device (KEM-460AAA), Wire (Flat Type) ....... 17 3. TEST MODE ............................................................ 18 4. ELECTRICAL CHECK ......................................... 27 5. DIAGRAMS 5-1. Block Diagram - SERVO Section - ................................ 28 5-2. Block Diagram - MEMORY Section - ............................ 29 5-3. Block Diagram - TUNER, S-AIR Section - .................... 30 5-4. Block Diagram - AUDIO Section - ................................. 31 5-5. Block Diagram - REGULATOR Section - ...................... 32 5-6. Block Diagram - PANEL, POWER SUPPLY Section - ........................... 33 5-7. Schematic Diagram - MB-134 Board (1/13) - ................ 35 5-8. Schematic Diagram - MB-134 Board (2/13) - ................ 36 5-9. Schematic Diagram - MB-134 Board (3/13) - ................ 37 5-10. Schematic Diagram - MB-134 Board (4/13) - ................ 38 5-11. Schematic Diagram - MB-134 Board (5/13) - ................ 39 5-12. Schematic Diagram - MB-134 Board (6/13) - ................ 40 5-13. Schematic Diagram - MB-134 Board (7/13) - ................ 41 5-14. Schematic Diagram - MB-134 Board (8/13) - ................ 42 5-15. Schematic Diagram - MB-134 Board (9/13) - ................ 43 5-16. Schematic Diagram - MB-134 Board (10/13) - .............. 44 TABLE OF CONTENTS 5-17. Schematic Diagram - MB-134 Board (11/13) - .............. 45 5-18. Schematic Diagram - MB-134 Board (12/13) - .............. 46 5-19. Schematic Diagram - MB-134 Board (13/13) - .............. 47 5-20. Printed Wiring Board - MB-134 Board (Component Side) - ............................. 48 5-21. Printed Wiring Board - MB-134 Board (Conductor Side) - ............................... 49 5-22. Printed Wiring Board - AUDIO Board - ......................... 50 5-23. Schematic Diagram - AUDIO Board - ............................ 51 5-24. Printed Wiring Board - MAIN Board (Component Side) - ................................ 52 5-25. Printed Wiring Board - MAIN Board (Conductor Side) - .................................. 53 5-26. Schematic Diagram - MAIN Board (1/5) - ..................... 54 5-27. Schematic Diagram - MAIN Board (2/5) - ..................... 55 5-28. Schematic Diagram - MAIN Board (3/5) - ..................... 56 5-29. Schematic Diagram - MAIN Board (4/5) - ..................... 57 5-30. Schematic Diagram - MAIN Board (5/5) - ..................... 58 5-31. Printed Wiring Board - CONNECT Board - ................... 59 5-32. Schematic Diagram - CONNECT Board - ...................... 59 5-33. Printed Wiring Board - REG Board - .............................. 60 5-34. Schematic Diagram - REG Board - ................................ 61 5-35. Printed Wiring Board - FL Board - ................................. 62 5-36. Schematic Diagram - FL Board - .................................... 63 5-37. Printed Wiring Board - POWER Board - ........................ 64 5-38. Schematic Diagram - POWER Board - .......................... 65 5-39. Printed Wiring Boards - KEY Section - .......................... 66 5-40. Schematic Diagram - KEY Section - .............................. 66 6. EXPLODED VIEWS 6-1. Case, Front Panel Section ............................................... 91 6-2. MB-134 Board Section ................................................... 92 6-3. Back Panel Section ......................................................... 93 6-4. MAIN Board Section ...................................................... 94 6-5. BD Drive Section (BPX-5) ............................................. 95 7. ELECTRICAL PARTS LIST .............................. 96 www. xiaoyu163. com QQ 376315150 92498299 8 TEL 13942296513 Q 376315150 892498299 Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com http://www.xiaoyu163.com

BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The fl exible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc refl ective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to fl ow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. Part No. Description Layer J-6090-199-A BLX-104 Single Layer J-6090-200-A BLX-204 Dual Layer J-2501-307-A CD (HLX-A1) J-2501-305-A HLX-513 Single Layer (NTSC) J-2501-306-A HLX-514 Dual Layer (NTSC) J-6090-077-A HLX-506 Single Layer (PAL) J-6090-078-A HLX-507 Dual Layer (PAL) TEST DISC Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883- 989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204. Operation and Display: 1. BLX-104 Procedure: 1. Select 23.976Hz/1080p. 2. Play “4.Motion picture”. 3. Check whether player can play back or not. 4. Check each outputs. Video: Composite/S Video/component/HDMI. Audio: Speaker out. * When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) can use instead of 1080/24p. However this is temporary correspondence. 2. BLX-204 Procedure: 1. Select 1080i (59.94Hz or 50Hz). 2. Play “4.Motion picture”. 3. Check whether player can play back or not (Check the picture and sound output). 3. CD (HLX-A1) Procedure: Check whether player can play back or not (Check the sound out- put). 4. HLX-513/514 (NTSC), HLX-506/507 (PAL) Procedure: 1. After displayed Main Menu, select “1.Video Signal”. 2. Play “1.Color bar 100%” (Check the picture and sound out- put). 3. Return to Menu. 4. Play “Demonstration 4:3” or “Demonstration 16:9” (Check the picture and sound output). NOTE THE IC101, IC104, IC105, IC204, IC205, IC307, IC311, IC501 AND IC502 ON THE MB-134 BOARD REPLACING IC101, IC104, IC105, IC204, IC205, IC307, IC311, IC501 and IC502 on the MB-134 board cannot exchange with single. When these parts are damaged, exchange the entire mounted board. RELEASING THE DISC TRAY LOCK The disc tray lock function for the antitheft of an demonstration disc in the store is equipped. Releasing Procedure: 1. Press the [?/1] button to turn on the system. 2. Press the [FUNCTION] button to select “BD/DVD”. 3. Press the [x] and [Z] buttons simultaneously and hold down unit “DEMO OFF” displayed on the fluorescent indicator tube (around 5 seconds). Note: When “DEMO ON” is displayed, the disc tray lock is not released by turning power on/off with the [?/1] button. ABOUT THE LENS CLEANING Do not do the lens cleaning with the cotton bud etc. It causes the trouble. www. xiaoyu163. com QQ 376315150 92498299 8 TEL 13942296513 Q 376315150 892498299 Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com http://www.xiaoyu163.com

When checking the board, the electrical discharge is necessary for the electric shock prevention. Connect the resistors referring to the fi gure below. • MAIN board (C3115, C3125, C3215, C3315, C3415, C3425) Both ends of CN3001. C3415 C3425 C3115 C3315 C3125 C3215 1 4 CN3001 – MAIN Board (Conductor Side) – 800 �/2 W • POWER board (C903, C932, C933) Both ends of respective capacitors. C903 C932 C933 – POWER Board (Conductor Side) – 800 �/2 W 800 �/2 W 800 �/2 W NOTE OF REPLACING THE OPTICAL DEVICE (KEM- 460AAA) OR MB-134 BOARD Optical device (KEM-460AAA) for BD requires precise read out functions and secure contents protection system for more than past DVD/CD. Therefore, in the case repaired as follows, the writing work of the OP data is necessary. • When the optical device (KEM-460AAA) is replaced (The MB-134 board doesn’t replace). • When both the optical device (KEM-460AAA) and MB-134 board are replaced. • When the MB-134 board is replaced (The optical device (KEM-460AAA) doesn’t replace) (In this case, do the work of “3. Optical device (KEM-460AAA) replacement” other than the replacement of new optical device). Note: The servo adjustment is done while writing the OP data. The manual adjustment is unnecessary. LD ON TIME history doesn’t carry over. Do not touch any optical block parts, turn table and during replac- ing. BD laser diode is very sensitive. 1. Preparation 1-1. ESD Countermeasure It is necessary to confi rm the state of static electricity in the work space before the repair is started. The static electricity resistance of the BD laser is weaker than that of the DVD/CD laser. Do work space and worker’s ESD countermeasures to prevent de- struction by ESD. 1-2. Jig • Digital camera (Recommend with macro mode) • USB memory • PC • Barcode decoder (Refer to “1-3. Barcode decoder (BDBUDEC)”) 1-3. Barcode decoder (BDBUDEC) Part No. : J-6090-212-A Jig name : BDBUDec.exe Release : 2009.02.19 Version : 1.0.0.0 Software contents : • BDBUDec.exe : Barcode decoder software • SavePath.ini : Decoded fi le destination setting fi le (Ini- tial destination is “C:\BuData.txt”) • TasmanBars.dll : Decode dll • Uninst.exe : Uninstall the “BDBUDec.exe” from PC Install procedure: 1. Unzip the barcode decoder fi les to any PC folder. 2. Check the taken barcode photo click & drop onto “BDBUDec. exe”. When the barcode decoder is used for the fi rst time, the pass- word is necessary. It is unnecessary since the second times. Note 1: The password will be supplied to only service headquarters, and service center name/q’ty/all of software registered information should be maintained by service headquarters. Note 2: Do not change the decoded fi le name “BuData.txt”. 3. When “.NET frame work requirements” is displayed, down- load following applications from Microsoft download site. • Microsoft .NET Framework Version 2.0 Redistributable Pack- age (x86) http://www.microsoft.com/downloads/details.aspx?displaylan g=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5 • Microsoft .NET Framework 2.0 Service Pack 1 (x86) http://www.microsoft.com/downloads/details.aspx?displaylan g=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5 www. xiaoyu163. com QQ 376315150 92498299 8 TEL 13942296513 Q 376315150 892498299 Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com http://www.xiaoyu163.com