GE GTX60GBSJ Installation Information

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. GTX60GBSJ GE® Series 6.2 cu. ft. capacity Aluminized alloy drum gas dryer with HE Sensor Dry Exhaust OptiOn: When viewed from the front of the unit, exhaust 3-way via rear, left and bottom. Dryer is shipped exhausted to the rear. Alternate exhausting knockouts are supplied. Gas: An individual, properly-grounded branch circuit, with a three-prong grounding-type receptacle, protected by a 15 or 20 amp circuit breaker or a time- delay fuse is required. Gas DryEr ElEctric ratinG: 120V, 60Hz, 6A Gas (Btu/hr): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check installation instructions for correct kit and have a qualified gas technician install a conversion kit. See dryer ducting information for proper installation. nOtE: Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position. installatiOn infOrmatiOn: For complete information, see installation instructions packed with your dryer. DimEnsiOns anD installatiOn infOrmatiOn (in inchEs) spEcial installatiOn rEquirEmEnts alcOvE Or clOsEt installatiOn: - If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back. - The dryer MUST be exhausted to the outside. - Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side; 3" front and rear - Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”. - Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed. - No other fuel-burning appliance shall be installed in the same closet with a gas dryer. BathrOOm Or BEDrOOm installatiOn: - The dryer MUST be exhausted to the outdoors. - The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers. minimum clEarancEs OthEr than alcOvE Or clOsEt installatiOn: - Minimum clearances to combustible surfaces are: 0" both sides; 3" rear DryEr ExhaustinG infOrmatiOn : - Use metal duct only, vertical and horizontal ducting.

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. GTX60GBSJ GE® Series 6.2 cu. ft. capacity Aluminized alloy drum gas dryer with HE Sensor Dry 22 1/2" 26 3/4" 4" 1 3/4" 3 1/4" 4 1/4" 37 1/2" 44" 27" 5" Power Cord 4 1/2" 11 3/4" Side View Rear View 5.7 cu. ft. Dryers 2 Back View Power Cord Hole 30-1/2 5.8, 6.0 and 7.0 cu. ft. Dryers 5 Back View Power Cord Hole 4-1/2 pOwEr cOrD lOcatiOns DimEnsiOns anD installatiOn infOrmatiOn (in inchEs)

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. Gtx60GBsJ GE® Series 6.2 cu. ft. capacity Aluminized alloy drum gas dryer with HE Sensor Dry DryEr ExhaustinG infOrmatiOn— usE mEtal Duct Only vErtical anD hOrizOntal DuctinG A B 2-1/2 4 GE Dryer Vent A B 2-1/2 4 A BEst pErfOrmancE Maximum length of 4" dia rigid metal duct Exhaust hood type Domestic dryer models Number of 90° turns A 4" opening B 2-1/2" opening GE Frontload Long Vent 7.0 cu. ft. capacity electric dryer (GFDL) 0 200 ft. 175 ft. 1 185 ft. 165 ft. 2 175 ft. 155 ft. 3 165 ft. 145 ft. 4 155 ft. 135 ft. 5 145 ft. 125 ft. Long Vent 6.0 - 8.0 cu. ft. capacity electric & gas dryers (GTDL and GTV) 0 150 ft. 125 ft. 1 135 ft. 115 ft. 2 125 ft. 105 ft. 3 115 ft. 95 ft. 4 105 ft. 85 ft. 5 95 ft. 75 ft. Long Vent 7.0 cu. ft. capacity electric & gas (GTD42, GTD45, GTD65, GTX42 and GTX60) 0 120 ft. 90 ft. 1 100 ft. 75 ft. 2 85 ft. 65 ft. 3 70 ft. 55 ft. 4 60 ft. 45 ft. 5 55 ft. 35 ft. All 6.0 - 8.3 cu. ft. capacity models electric and gas dryers (GFDS, GFDR, GFDN, GTDS, GTDN, GHDN, GHDS, GTDP, GLDP, GTD, HTDP, HTDX) 0 90 ft. 60 ft. 1 60 ft. 45 ft. 2 45 ft. 35 ft. 3 35 ft. 25 ft. 4 25 ft. 15 ft. DCVH480 0 90 ft. 60 ft. 1 60 ft. 45 ft. 2 45 ft. 35 ft. 3 35 ft. 25 ft. All 3.6 cu. ft. (DSKS, DSKP) electric dryers 0 46 ft. 37 ft. 1 37 ft. 30 ft. 2 30 ft. 22 ft. 3 23 ft. 15 ft. Laundry Center GUD27 0 56 ft. 42 ft. 1 48 ft. 34 ft. 2 40 ft. 26 ft. 3 32 ft. 18 ft. Laundry Center GUD24 0 43 ft. 36 ft. 1 33 ft. 26 ft. 2 24 ft. 16 ft. fOr cOmplEtE infOrmatiOn, sEE installatiOn instructiOns packED with yOur DryEr. DuctinG matErials: For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi- rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting. Exhaust lEnGth calculatiOn: 1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn. 2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow. Dryers must be exhausted to the outside. cautiOn: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down. fOr mOrE infOrmatiOn On vEntinG kits anD accEssOriEs, plEasE call 1-800-GE-carEs.

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. GTX60GBSJ GE® Series 6.2 cu. ft. capacity Aluminized alloy drum gas dryer with HE Sensor Dry GTX60EBSJWS_GTX60GBSJWS fEaturEs anD BEnEfits ENERGY STAR® qualified – Meets or exceeds federal guidelines for energy efficiency for year-round energy and money savings Up to 120 ft. venting capability – Provides flexible installation Extended Tumble – Freshly tumbles your garments periodically for up to 8 hours when unable to move clothing to the dryer right away HE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermistors continually monitor temperature with a sensor bar that measures moisture to prevent over-drying My Cycle Settings – Dry clothes with the settings you prefer on any cycle, rather than the defaults, and store your settings for later use Damp Alert – Alerts you when clothes are the ideal dampness for ironing, for perfectly wrinkle-free results Model GTX60GBSJWS – White with silver backsplash