Goodmans MICRO1112DAB Operation & User’s Manual

User Guide IMPORTANT: Please read all instructions carefully before use and keep for future reference all-guides com

your favourite radio stations and CD's. It’s really simple to use; you can fully operate your DAB Micro system using the supplied Remote Control. Throughout this User Guide the DAB Micro will be referred to as the Micro System. Safety is important Use of any electrical equipment should be undertaken with care. Please read the Safety instructions on pages 19 & 20 before you operate this Micro System.

Get going .....................................6 Using the radio ...........................10 Using the DAB radio .....................7 05 Using the CD ..............................11 Using the Clock and Timer.............14 Other functions...........................16 Troubleshooting............................17 Specifications .............................18 2 x AAA batteries for remote control DAB Micro 06 07 08 09 This User Guide Remote Control MICRO1112DAB DAB MICRO User Guide IMPORTANT: Please read all instructions carefully before use and keep for future reference Quick Start Guide MICRO1112DAB DAB MICRO Start here What’s in the box Contents

PLAY MODE Button MEMORY/CLOCK Button Skip << Backwards Button Skip >> Forwards Button STOP Button FUNCTION Button VOL+ Button VOL- Button PLAY/SCAN Button ENTER Button INFO Button CD Door STANDBY/ON Button REMOTE CONTROL Sensor LCD Display AUX IN socket HEADPHONE socket Mains Power Lead Antenna SPEAKER Terminal Front Rear

STANDBY Button INFO/ESP/DISPLAY Button CLOCK ADJ./PROGRAM Button MENU Button FUNCTION Button PLAY/SCAN Button PLAY MODE Button FOLDER UP Button FOLDER DN Button EQ Button NUMBER Buttons SLEEP Button ENTER Button BASS Button VOL- Button VOL+ Button RWD Button FWD Button STOP Button TIMER Button AUX Button MUTE Button Remote Control File +10 Button

Insert two AAA batteries into the remote control while observing the correct (+) and (-) polarities as shown. 1 Get going 2 Using Headphones A pair of headphones (not supplied) with a 3.5mm diameter stereo plug and 8-32 ohm impedance is required. Plug the headphones into the Headphone Socket at the back of the Micro System. When headphones are connected, the speakers are automatically muted. all-guides com

stations within your region. The radio stations found are stored. ■ In addition to digital audio your DAB radio can Extend the wire aerial on the rear of the DAB radio. Press the STANDBY/ON button to switch on your radio. display information such as Program name, Program type, Network provider, Signal strength, Current time and date, and scrolling text information. For initial use, press the PLAY/SCAN button. The DAB radio will make a quick scan and store the stations in memory. When the scanning is completed, the DAB stations will be displayed in alphanumeric order. The first station in the list will be selected. Press the <> button to cycle through available stations. Press the ENTER button to select the chosen station. 03 Using the DAB radio Introduction Turning on the DAB radio Scanning for Radio Stations 1 2 3 Note : For a full Scan, press and hold the PLAY/SCAN button for a few seconds.

Manual Tune This will display as follow Displays the software version of this DAB radio. SW Version DRC (Dynamic Range Control) value Press the MENU button on remote control and press <>buttons until the name of the option is displayed. press ENTER press >> press >> press >> press >> press >> press >> press >> press ENTER press ENTER press ENTER Normally the default setting 0 is best, but if you are listening in a noisy place then setting DRC to 1 will make quiet sounds, like speech louder and easier to hear.

1. Whilst listening to a station, repeatedly press the INFO button to select the information required, the display will show the information in the bottom line of the LCD display. The following screens show typical examples: The text may show information on music titles or details of the programme and is provided by the broadcaster. This is a description of the type of programme provided by the broadcaster. This will show the network that is broadcasting the programme you are listening to. This displays the time and date information provided by the broadcaster. In good signal conditions it will always be accurate. This displays the channel number and the transmission frequency. This shows the digital bit-rate and the mode. If the transmission signal contains errors the system can apply correction. The amount of signal correction can be displayed as a numerical value between 0 and 99. As the value increases, you will hear the signal degrade. To improve reception, try adjusting the position of the aerial. You can also display the signal strength of a DAB station. When tuned to the station press the ENTER button . The LCD screen will show a bar graph indicating the strength of the signal - the more squares the stronger the signal. The open square indicates the minimum signal strength required for good reception. Program name Program type Multiplex name Signal error rate Current time and date Scrolling text information Channel and frequency Bit rate and mode 03 Using the DAB radio Displaying DAB information Scrolling Text: Program Type Network Name Time and Date Channel and Frequency Signal Information Signal Error Rate Signal Strength There are 10 presets to store your favourite DAB stations. To store a station to a preset button on your remote control: Whilst listening to a station press and hold the number button that you wish to use to preset this station until ‘Preset saved’ is displayed. For example, to store a station in preset 4: Whilst listening to a station press the 4 button until the LCD shows ‘Preset 4 saved’. To recall a station in preset 4: Briefly press the 4 button on the remote control, the LCD display will show the selected station. If preset 4 had not been previously assigned to a station the LCD display would show ‘Empty preset’. To preset 10 press and hold the +10 button. To reset the DAB radio, press and hold the MEMORY/CLOCK button for 5 seconds “Factory RESET” appears, then press the PLAY/SCAN button to confirm. Note: This will force the system to re-scan. Any previously stored preset stations will be lost. Store and recall a preset station Manual Reset 1 2

10 04 Basic operation RDS Press the STANDBY button on the main unit to power on. Press the FUNCTION button on the unit to select Tuner mode. Tune to the station you want by pressing the >>/<< buttons. 1 2 3 4 1 2 3 4 Antenna Preset stations Select TUNER mode. Tune to the desired radio station by pressing the PLAY/SCAN or the << / >> buttons. You can store up to a total of 20 radio stations in the memory (10-FM) DON’T FORGET! There is a built-in antenna wire on the back of the unit. Move the wire around to get the best reception. For best DAB reception stretch the wire vertically. To display data information: 1. Whilst listening to a station repeatedly press the INFO button to select the data information required, the display will show the data information in the bottom line of the LCD display. The following LCD display screens show typical examples of data information which is shown in the bottom line of each screen: This is scrolling text information supplied by the FM station. It may show information on music titles or details of the programme and is provided by the broadcaster. “NO RT” will be shown if FM station with RDS is not available. This is a description of the type of programme provided by the FM station and is provided by the broadcaster. “NO PTY” will be shown if an FM station with RDS is not available. This displays the time and date and is provided by the broadcaster, so will always be accurate. “NO CT” will be shown if an FM station with RDS is not available. This displays the transmission frequency. Program name Program type Current time and date Scrolling text information Frequency Displaying data information Radio Text - Scrolling Text: Program Type Time and Date Frequency To automatically scan to the next available station, press the PLAY/SCAN button. Press and hold the desired number button on the remote control to store the radio station, for example button number 4. After 2 seconds the display will show "Preset 4 saved". To recall a preset station in preset 4, briefly press the 4 button on the remote control. The radio will switch to the desired station. If no preset station has been assigned to preset memory 4, the display will show "Empty preset".

11 05 ������� ��� ��������� ��� ����� ��� ������� ������ �� ���� �� ��� ����� ���������������������������� ������ �� ����� ���� ��� ���� ����������� ����������� ���� �������� ����������� ����������� ������ � ���� ���� ��� ���� ��� �������� �������������� ��� ���� ���� ��������� ���� ������ �������� ����� ������� �� ��� ��� �������� ������ �������������� �������� ������������ ����� ������� ��� ���������� ����� ������������������������������������������� ������������������������� ���� ��� ����������� �� ����� ������� ��� ���� ���� ������� �������������� ��� ����� ������ �� ������ �� ��� �� ���� ������ ������ ��� �������� � � � � � � ����� ������� ������������������������� ������ ���� ��� �� ��� �� ������� ���� ��� ���� ���� ������������ ���������� ����� ����� ��������� ��� ���� ���� ��� ���������������� �� ��� ����� ������� ��� ����� ��� ��������� ������ ���� �� ����������������� ������ ���� ��������� ������ ����� ��� ��������� ������ ���� �� ����� �������� �� ��� ��� ���������������������� ���� ����� ������ �������� �� ���� ��������� ����� ��� ���� ������� ��������� � ��������� �� ����� ����� ��� ���� ������� �� ���� ��������������������� ������� ��� ������ �� ��� ��� ����� ��� ���� ��� ���� ������� �� ���� �������� �� ��������� ������� ��� ������� ������ ���� ��� ������� ������� ��� ����� �� �������� ���������������������� �������� ������������ � � � � � � ����������������������� all-guides com

12 05 Play Mode To repeat the current track, press the PLAY MODE button once. “ ” will show in the display. To repeat the entire disc, press the PLAY MODE button twice. “ ” will show in the display. To cancel repeat play, press the STOP button or press the PLAY MODE button until the repeat indicator disappears. Random CD playback In play mode press the PLAY MODE button on the remote control three times, “ r ” will show in the display, and the tracks will be played in a random order. To cancel random play, press the STOP button or press the PLAY MODE button until the random indicator disappears. Playing MP3 and WMA CDs When playing a CD encoded with MP3 or WMA files, the functions available and operations are similar to those when playing a standard CD. 1 2 3 1 2 5 6 1 2 3 4 To clear the memory, press the STOP button twice. Programmed CD/MP3 playback Up to 64 tracks can be programmed to the internal memory in any order. You may also store the same track more than once. In stop mode, press the MEMORY/CLOCK button P-O1 will show in the display. Select the desired track or folder by pressing the << or >> buttons. When the desired track is chosen, press the MEMORY/CLOCK button to store the track. P-O2 will show in the display. Repeat steps 2 and 3 to select and store up to 64 tracks. To listen to stored tracks, press the PLAY/PAUSE button. Use the << or >> buttons to skip through the tracks.

13 05 Searching MP3/WMA tracks Press PLAY/SCAN to confirm the selection. press INFO press INFO press >> press >>

14 06 Setting the clock DON’T FORGET! This unit has its own digital clock when in standby mode. The clock displayed will be synchronized by the DAB signal when the unit is in DAB mode. To adjust the clock and set the timer, follow the instructions below:(at STANDBY mode) Press the MEMORY/CLOCK button for a few seconds and select either 24 hour or 12 hour mode using the >> / << buttons. Press the MEMORY/CLOCK button to confirm. The hour digits will begin to flash. Adjust the hours by pressing the >> / << buttons. Press the MEMORY/CLOCK button again, and the minute digits will begin to flash. Adjust the minutes by pressing the >> / << buttons. Press the MEMORY/CLOCK buttom to confirm DON’T FORGET! The clock setting will be lost if the power is disconnected. 1 2 3 4 5 6 Setting the sleep timer DON’T FORGET! You need to use the remote control to use this function. The Sleep Timer is a countdown timer for switching the system to standby mode after a specified time. It enables you to listen to the radio or CD. The Sleep Timer can be set from 90 to 10 minutes. Switch on the system by pressing the STANDBY button. Select the desired source by pressing the FUNCTION button. Press the SLEEP button to set the sleep time. - SLEEP and 90 are shown in the display. The system will now play for 90 minutes. To decrease the sleep time , continually press the SLEEP button until the desired sleep time is shown. To cancel the sleep timer, press the SLEEP button until the display returns to the previous mode. To switch off the system before the sleep time has elapsed, press the STANDBY button. 1 2 3 4 5 6 Note: Pressing the SLEEP button at any time will show the time remaining before the unit will switch off. The clock of the unit is synchronized when the unit is ON and at DAB mode.

15 06 Setting the timer DON’T FORGET! You need to use the remote control to use this function. In STANDBY mode press the TIMER button.”ON TIME” will be shown and the hour digits will begin to flash. Adjust the hour by pressing the >> / << buttons. 1 The timer is used to switch the system ON and OFF at a specified time. It enables you to listen to the DAB/FM radio, CD or AUX device. Press the TIMER button to confirm and the minute digits will begin to flash. Adjust the minutes by pressing the >> / << buttons. 2 Press the TIMER button to confirm and “OFF TIME” will be shown. Follow the same procedure as in steps 1 and 2 to set the Timer OFF time, then press the TIMER button to confirm. 3 The function mode will cycle as below : Select the desired source by pressing the >> / << buttons and press the TIMER button to confirm. 4 The volume level will be shown. Select the level by pressing the >> / << buttons and press the TIMER button to confirm. 5 DAB FM CD AUX

control to use this function. Press the MUTE button on the remote control to turn off the sound. MUTE will flash in the display. Press the MUTE button again to restore the sound to the previous level. Preset Equaliser Choose from: CLASSIC, ROCK, POP, JAZZ, and FLAT. Press the EQ button to cycle through the settings. 1 2 Resetting Press BASS button on the remote control to turn bass boost ON/OFF. Remove the mains power lead from the wall socket. Leave the unit disconnected from the power supply for 1 minute, then reconnect and power on the unit. DON’T FORGET! if the power supply is disconnected. 1 Press the FUNCTION button repeatedly to select AUX mode. 1 Connect your device to the AUX IN socket on the front of the unit. 2 Control your device as usual for audio playback. 3 2 3 Note: Only ID3 tag version 1 is supported. For music playback from an auxiliary device. ID3 Tag (Title/Artist/Album) Function Aux In Device Bass In DAB or FM mode, press the MEMORY/ CLOCK button (on the main unit) for 5 seconds. Factory RESET will show in the display. Press the PLAY button to confirm the reset. All preset memory stations will be erased when the system is reset Electronic Shock Protection This feature helps to eliminate any break in the playback of the disc due to errors or imperfections. ESP The clock time will be lost If you experience any abnormal operation when using the Micro System, follow the procedure below to perform a system reset: ID3 tag information (Title/Artist/Album) can be displayed when playing a MP3 or WMA CD by pressing the INFO button during playback. all-guides com

Radio DAB Noise or sound distorted on FM Station not tuned properly for FM The FM antenna wire is not extended. Fine tune FM broadcast station Extend FM wire antenna No sound in FM mode Unit not in radio mode Volume is at the minimum position Adjust the volume level CD/MP3 Player CD Player will not play Unit not in CD mode CD is not installed or installed correctly Select CD mode Load a CD and check it is the correct way round. CD skips while playing Disc is dirty or scratched Wipe the disc with a cloth or use another disc Need extra help? Don’t worry we are just at the other end of the phone. If you are experiencing problems using your new product, before returning it to the retailer, just call 0871 230 1777. Need a spare part? In the unlikely event of you need- ing spare parts, please contact our spares department on: 0871 230 0790 Not functioning correctly Refer to reset procedure Garbled sound Poor signal Move aerial wire MP3 disc not playing correctly Poor quality data, wrong type of file i.e. aac, flac, ogg,m4a try making new copy, check the file type is .MP3 or .WMA Title/Artist/Album (ID3 Tag) not working correctly Data not correct on the CD MP3 on computer has correct ID3 info but unit does not display it Version of ID3 not supported Get ID3 data in ID3 version 1 Aux In Volume too low on connected device Increase the volume on connected device Microprocessor malfunction Press the function button to select radio mode. Re-record the disc, or try another. Sound is quiet

Power consumption Remote control • 230 - 240V ~ 50 Hz Power Output • 2 x 2W RMS Radio Frequency Coverage • FM 87.5-108 MHz, DAB 174 - 224MHz Dimensions Unit Speaker p • W170mm X D205mm X H145mm • W154mm X D165mm X H145mm • 2 X 1.5Volt "AAA" batteries • 25W Specifications IMPORTAN T T:This manual contains fo : r-reference-only graphics and information that are subject to change without prior notice.

please take care when operating this equipment. It is strongly recommended that you follow the guidelines in order to prevent possible damage to, or loss of hearing. Over time your hearing will adapt to continuous loud sounds and will give the impression that the volume has in fact been reduced. What seems normal to you may in fact be harmful. To guard against this, set the initial volume of the equipment to a low level. Follow the steps below to ensure that the product can be enjoyed at a comfortable listening level: Slowly increase the level until you can hear comfortably and clearly and without distortion. Damage to your hearing is accumulative and irreversible. Any "ringing" or discomfort in the ears indicates that the volume is too loud. Once you have established a comfortable listening level, do not increase the volume level. General Safety This equipment has been designed and manufactured to meet European safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Do read these operating instructions before you attempt to use the equipment. Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) 1 2 3 are properly made in accordance with the manufacturer’s instructions. Switch off and remove the mains plug when making or changing any connections. Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. Don’t continue to operate the equipment if you are ever in doubt about it working normally, or if it is damaged in any way. Switch it off withdraw the mains plug and consult your dealer. Don’t remove any fixed covers as this may expose you to dangerous voltages. Don’t leave the equipment switched On when it is unattended, unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that other people in your household are conversant with the equipment. Special arrangements may need to be made for infirm or handicapped people. Don’t obstruct the ventilation vents on the equipment, for example with curtains or soft furnishings. Overheating will cause damage and shorten the life of the product. Don’t allow electrical equipment to be exposed to rain or moisture.

and replaced with an appropriate plug. If the plug becomes damaged and/or needs to be replaced please follow the wiring instructions below. The plug removed must be disposed of immediately. It must not be plugged into a supply socket as this will be an electrical hazard. If the fuse needs to be replaced it must be of the same rating and ASTA approved to BS1362. If the plug is changed, a fuse of the appropriate rating must be fitted in the plug, adapter or at the distribution board. If the fuse in a moulded plug is replaced, the fuse cover must be refitted before the appliance can be used. Wiring Instructions The supply cable will be either 2-core or 3-core. Follow the appropriate wiring instructions given below. In both cases ensure that the outer sheath of the cable is firmly held by the cable clamp. WARNING � : Do not connect either wire to the earth terminal. 2- Core plug This symbol indicates that this 2-core appliance is Class II and does not require an earth connection. The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red Fuse Brown (Live) Blue (Neutral) Green & yellow (Earth) Fuse Brown (Live) Blue (Neutral) 3- Core plug The wire coloured green and yellow must be connected to the terminal marked with the letter E, or by the earth symbol � or coloured green or green and yellow. The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. WARNING � : This appliance must be earthed. WEEE This appliance is labelled in accordance with European Directive 2002/96/EG concerning used electrical and electronic appliances (Waste Electrical and Electronic Equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances.