HP A5500 SI Switch Series Configuration Manual

Ethernet Ethernet Ethernet N1 N2 Vlan-int102 Vlan-int102 Vlan-int103 Vlan-int103 Device Interface IP address Device Interface IP address Switch A Vlan-int100 10.110.1.1/24 Switch D Vlan-int300 10.110.5.1/24 Vlan-int103 192.168.1.1/24 Vlan-int103 192.168.1.2/24 Switch B Vlan-int200 10.110.2.1/24 Vlan-int101 192.168.2.2/24 Vlan-int101 192.168.2.1/24 Vlan-int102 192.168.3.2/24 Switch C Vlan-int200 10.110.2.2/24 Vlan-int102 192.168.3.1/24 Configuration procedure 1. Configure IP addresses and unicast routing. Configure the IP address and subnet ...

Remarks Enter system view system-view — Enter public network IGMP view or VPN instance IGMP view igmp [ vpn-instance vpn-instance- name ] — Configure the IGMP querier’s robustness variable robust-count robust-value Optional 2 by default Configure the startup query interval startup-query-interval interval Optional By default, the startup query interval is 1/4 of the “IGMP general query interval.” Configure the startup query count startup-query-count value Optional By default, the startup query count is set to the IGMP querier’s robustness variable. Con ...

[SwitchD] mld [SwitchD-mld] ssm-mapping ff3e:: 64 1001::1 [SwitchD-mld] ssm-mapping ff3e:: 64 3001::1 [SwitchD-mld] quit 6. Verify the configuration Use the display mld ssm-mapping command to view MLD SSM mappings on the switch. # Display the MLD SSM mapping information for IPv6 multicast group FF3E::101 on Switch D. [SwitchD] display mld ssm-mapping ff3e::101 Group: FF3E::101 Source list: 1001::1 3001::1 Use the display mld ssm-mapping group command to view information of the MLD groups created based on the configured MLD SSM mapping ...

table, respectively: { The router searches its IPv6 unicast routing table using the IPv6 address of the packet source as the destination address and automatically selects the optimal route as the RPF route. The outgoing interface in the corresponding routing entry is the RPF interface and the next hop is the RPF neighbor. The router considers the path along which the IPv6 multicast packet from the RPF neighbor arrived on the RPF interface to be the shortest path that leads back to the sourc ...

To enable the BSR to distribute the RP-set information within the IPv6 PIM-SM domain, C-RPs must periodically send C-RP-Adv messages to the BSR. The BSR obtains the RP-set information from the received messages, and encapsulates its own IPv6 address together with the RP-set information in its bootstrap messages. The BSR then floods the bootstrap messages to all IPv6 routers in the network. Each C-RP encapsulates a timeout value in its C-RP-Adv messages. Upon receiving a C-RP-Adv message, the BSR obtains this timeout value and starts a C-RP timeout timer. If ...

[SwitchD-Vlan-interface104] quit # Enable IP multicast routing on Switch A, and enable PIM-SM on each interface. system-view [SwitchA] multicast routing-enable [SwitchA] interface vlan-interface 100 [SwitchA-Vlan-interface100] pim sm [SwitchA-Vlan-interface100] quit [SwitchA] interface vlan-interface 101 [SwitchA-Vlan-interface101] pim sm [SwitchA-Vlan-interface101] quit [SwitchA] interface vlan-interface 104 [SwitchA-Vlan-interface104] pim sm [SwitchA-Vlan-interface104] quit The configuration on Switch B and Switch C is similar to that on Switc ...

Remarks Configure the maximum response delay for MLD general query messages mld max-response-time interval Optional 10 seconds by default Configure the MLD last listener query interval mld last-listener-query-interval interval Optional 1 second by default Configure the MLD other querier present interval mld timer other-querier-present interval Optional By default, the other querier present interval is determined by the formula: Other querier present interval (in seconds) = [ MLD query interval ] × [ MLD querier’s robustness variable ] + [ maximum response del ...