Mango X- series Getting Started Manual

The Handheld Experts! #1 in Route Delivery Software! Advantage Route Systems, Inc. - 3201 Liberty Square Parkway Turlock, CA 95380 USA - 1.209.632.1122 - Toll Free (USA) 888.294.7688 - www.AdvantageRoute.com - [email protected] Getting Started Guide 2. Installing the Battery Pack 1) Using the supplied screw driver, unscrew the six screws on the back cover. 2) Insert battery with the arrows visibile and pointing down towards the bottom of the handheld. 3) Replace back cover and be sure to tighten the screws firmly - but not too tight. Note: If you do not see the battery in your package materials, then your battery has already been installed into your device. 3. Connecting the Power Adapter to Charge the Handheld 1) Connect the USB power cable to the AC or DC power adapter with the larger connector. 2) Insert power adapter into either an AC/DC outlet. 3) Gently open the cover to the USB port on the right side of the handheld. Insert the smaller end of the power cord into the USB port. AC Adapter (Optional) Wireless Charging Standard Battery 1. Open the package and check your accessories. USB Cable Earphones DC Adapter Screwdriver Antenna (RX only)

Rear Facing Camera Speaker Ear phone Jack Connector Volume Control Walkie Talkie Front Facing Camera USING PERIPHERALS Putting in the SIM/SD Card 1) Turn off device, remove back cover, and remove battery. 2) Insert a correctly oriented SIM card, metal side down. You can use either slot for the SIM card. 3) If you would like to use an SD card for external storage, insert the card into the provided slot. 4) Replace battery. 5) Put the battery cover back in place Note: Never remove the SIM/SD card when an external power supply is connected. This may cause damage to the card or to your phone. SIM #2 (Micro) SIM #1 (Micro) Micro SD Card Advantage Route Systems, Inc. - 3201 Liberty Square Parkway Turlock, CA 95380 USA - 1.209.632.1122 - Toll Free (USA) 888.294.7688 - www.AdvantageRoute.com - [email protected] Emergency Flashlight USB Port Reset Camera

3) Move the Wi-Fi slider to the “on” position (to the right). 4) Select “Wi-Fi” and then select your access point. 5) Enter the security key for your connection (if secured). 1) Navigate back to the Settings screen select and slide the Bluetooth slider to the ”on” position (to the right) 2) Under “Available Devices”, choose your printer. 4) Enter your device’s PIN. The PIN will either be 1234 or 0000. SETTING UP YOUR DEVICE INSTALLING THE APPLICATION 3) If you are not sure which listed device is your printer, print a test page to get the info. You can do this by turning the printer OFF, then hold down the feed button and turn the printer ON. Once it is on, let go of the Feed button and the test page will print. Generally the name or model number will be near the top. 1) When asked if you would like to install this application, select “Next” 3) When asked if you would like to download data from your server, select “Yes” 4) Enter your server information. For assistance, contact Advantage Route Systems at the phone number below. 3. Security 1) Navigate back to the Settings icon and access the Security icon 2) Slide “Unknown Sources” slider to “on” position This step is necessary in order to allow you to receive updates from Route Manager, as these updates are not available in your Google Play Store. 2) Select Install then “open” Note: You will need to complete these steps if you are using a Bluetooth printer such as the PTB2/3 or BT4. 2. Setting Up Bluetooth 1. Setting Up Wi-Fi Advantage Route Systems, Inc. - 3201 Liberty Square Parkway Turlock, CA 95380 USA - 1.209.632.1122 - Toll Free (USA) 888.294.7688 - www.AdvantageRoute.com - [email protected] 1) Turn the power on to your device. 1. Download 1) Open a new web browser 2) Type your download server into the web addres bar 3) The download screen will appear and show progress of download. Wait until complete. RMA Server: sh003.ars247.com:46001 RM2000 Server: sh003.ars247.com:46101 2. Install All devices purchased through Advantage Route Systems will have already completed the steps below.

global distributor of route automa on solu ons. Since 1994, ARS has been the leader in route accoun ng, handhelds, GPS and other applied technologies for Bo led Water, Water Treatment, Ice, Propane, Oil Recycling and many more industries. With an installed base of over 5,000 routes in 45 countries, ARS consistently brings quality products to the market for progressive companies. Its 24 X 7 world-wide customer service center is second to none. Adva globa 1994 hand Wate many route produ 7 wo Dec 2014 1) Never use strong pressure on the screen or subject it to severe impact, as the LCD panel can crack and possibly cause personal injury. If the LCD panel is broken, never touch the liquid inside, because the liquid irritates the skin. 2) Use only the original approved AC adapter with the device. Use of an unapproved AC Adapter could result in electrical problems,or even cause a f re or electrical shock to the user. 3) Do not disassemble the handheld. Servicing should be done by Authorized Suppliers only. If the device or accessories are damaged due to improper handling, unauthorized repair or warranty seals are broken, the warranty will be void. 4) Make regularly back-ups of all important data. 5) Under no circumstance will the Manufacturer (or its agents) be liable for any direct, indirect, consequen al or incidental damages arising from the use or inability to use both the hardware and so ware and/or any data loss, even if the Manufacturer (or its agents) has been informed about the possibility of such damages. WPP Do not throw this product in the home waste bin. For proper end-of-life treatment consult the Environmental care sec on of p:// p.sccltd.com.tw For CE, FCC and other DoC's, consult the Regulatory sec on of p:// p.sccltd.com.tw This device complies With part 15 of the FCC rule Opera on is subject to the following two condi ons. (1)This device may not cause harmful interference. (2)This device must accept any interference received. Including interference that may cause undesired opera on. Complies with 21 CFR 1040.10 and 1040.11 except for devia ons pursuant to Laser No ce No. 50, Date June 24 2007. Lithium-ion battery packs may get hot, explode, ignite and/or cause serious injury in case of misuse. Please follow the safety warnings listed below: 1) Do not throw the battery into fire. Do not expose the battery to high temperatures. 2) Do not connect the positve battery pack with negatve battery pack to each other with any metal object (like wire). 3) Do not carry or store battery pack together with metal objects. 4) Do not pierce the battery pack with nails or drills, strike the battery pack with a hammer, step on the battery pack or otherwise expose it to strong impacts, shocks or excessive force. 5) Do not expose battery pack to liquid or allow the battery contacts to get wet. 6) Do not disassemble or modify the battery pack. The battery pack contains safety and protec!on measures, which, if damaged, may cause the battery pack to generate heat, explode or ignite. 7) Do not discharge the batteries outside the handheld. Do not use the battery in a device other than the hanheld or series battery chargers because the battery pack can become damaged, and the life expectancy reduced. If the device causes any abnormal current to flow, it may cause the battery pack to become hot, explode or ignite and cause serious injury. 8) In the event the battery pack leaks and the fluid gets into one's eye, do not rub the eye. Rinse well with water and immediately seek medical care. If let untreated,the battery fluid could cause damage to the eye. BATTERY PRODUCT SAFETY USER AND PRODUCT SAFETY The Handheld Experts! #1 in Route Delivery Software! Advantage Route Systems, Inc. - 3201 Liberty Square Parkway Turlock, CA 95380 USA - 1.209.632.1122 - Toll Free (USA) 888.294.7688 - www.AdvantageRoute.com - [email protected] The device will be powered on when you install the battery pack. Charge the battery for at least 4 hours. Do not turn on the device for the first time until the battery is charged for at least 4 hours. Always charge the batteries in a 6C-40C (32F-104F) environment temperature. CAUTION: