iSolution iMove 350S Operation & User’s Manual
Read Online
Read the iSolution iMove 350S Operation & User’s Manual online using the built-in PDF viewer.
Text of the manual
Order
Ref:
ISIM31
-‐
User
Manual
Please
read
the
instructions
carefully
before
use
1
CONTENTS
1.
Safety
Instruction
.....................................................................................................
2
2.
Technical
Specifications
...........................................................................................
4
3.
How
To
Set
The
Unit
................................................................................................
6
3.1
Rear
Panel
..........................................................................................................
6
3.2
Main
Function
....................................................................................................
7
3.3
Home
Position
Adjustment
..............................................................................
15
4.
How
to
Control
the
Unit
........................................................................................
16
4.1
Master/Slave
Built
In
Preprogrammed
Function
.............................................
16
4.2
Easy
Controller
.................................................................................................
17
4.3
DMX
Controller
................................................................................................
17
5.
DMX512
Configuration
..........................................................................................
18
6.
DMX
Connection
....................................................................................................
20
7.
Troubleshooting
.....................................................................................................
21
8.
Fixture
Cleaning
.....................................................................................................
22
2
1.
Safety
Instruction
WARNING
Please
keep
this
User
Guide
for
future
consultation.
If
you
sell
the
unit
to
another
user,
be
sure
that
they
also
receive
this
instruction
manual.
Unpack
and
check
carefully
there
is
no
transportation
damage
before
using
the
unit.
Before
operating,
ensure
that
the
voltage
and
frequency
of
power
supply
match
the
power
requirements
of
the
unit.
It’s
important
to
ground
the
yellow/green
conductor
to
earth
in
order
to
avoid
electric
shock.
The
unit
is
for
indoor
use
only.
Use
only
in
a
dry
location.
The
unit
must
be
installed
in
a
location
with
adequate
ventilation,
at
least
50cm
from
adjacent
surfaces.
Be
sure
that
no
ventilation
slots
are
blocked.
Disconnect
mains
power
before
replacement
or
servicing.
Make
sure
there
are
no
flammable
materials
close
to
the
unit
while
operating
as
it
is
a
fire
hazard.
Use
a
safety
cable
when
mounting
this
unit.
DO
NOT
handle
the
unit
by
taking
its
head
only,
but
always
by
taking
its
base.
Maximum
ambient
temperature
is
Ta:
40°.
DO
NOT
operate
it
where
the
temperature
is
higher
than
this.
Unit
surface
temperature
may
reach
up
to
85°.
DO
NOT
touch
the
housing
bare-‐hand
during
its
operation.
Turn
off
the
power
and
allow
about
15
minutes
for
the
unit
to
cool
down
before
replacing
or
servicing.
In
the
event
of
a
serious
operating
problem,
stop
using
the
unit
immediately.
Never
try
to
repair
the
unit
by
yourself.
Repairs
carried
out
by
unskilled
people
can
lead
to
damage
or
malfunction.
Please
contact
the
nearest
authorised
technical
assistance
center.
Always
use
the
same
type
spare
parts.
DO
NOT
touch
any
wire
during
operation
as
high
voltage
might
cause
electric
shock.
Please
read
carefully
the
instruction,
which
includes
important
information
about
the
installation,
usage
and
maintenance.
3
Warning
To
prevent
or
reduce
the
risk
of
electrical
shock
or
fire,
do
not
expose
the
unit
to
rain
or
moisture.
DO
NOT
open
the
unit
within
fifteen
minutes
after
switching
off.
The
housing,
the
lenses,
or
the
ultraviolet
filter
must
be
replaced
if
they
are
visibly
damaged.
Caution
There
are
no
user
serviceable
parts
inside
the
unit.
DO
NOT
open
the
housing
or
attempt
any
repairs
yourself.
In
the
unlikely
event
your
unit
may
require
service,
please
contact
your
nearest
dealer.
Installation
The
unit
should
be
mounted
via
omega
bracket
(see
below).
Always
ensure
that
the
unit
is
firmly
fixed
to
avoid
vibration
and
slipping
while
operating.
And
make
sure
that
the
structure
to
which
you
are
attaching
the
unit
is
secure
and
is
able
to
support
a
weight
of
10
times
of
the
unit’s
weight.
Also
always
use
a
safety
cable
that
can
hold
12
times
of
the
weight
of
the
unit
when
installing
the
fixture.
Professionals
must
fit
the
equipment.
It
must
be
fixed
at
a
place
where
is
out
of
reach
and
has
no
one
passing
by
or
under
it.
4
2.
Technical
Specifications
Construction:
Stylish
design
with
fire
retardant
plastic
housing
Fastening
System:
2
x
Omega
clamps
Excellent
ventilation
for
reliable
operation
Rotating
Gobo
Wheel:
6
rotating
and
changeable
gobos
plus
open
Color
Wheel:
8
colors
plus
white
Adjustable
manual
focus
Pan/Tilt:
Pan/Tilt:
540°/270°
Automatic
Pan/Tilt
position
correction
Easy
calibration
and
maintenance
by
magnetic
home
positioning
Control:
3
DMX
control
modes:
DMX,
Master/Slave
and
Sound
Active
DMX
channel
modes:
8/11CH
LED
display
for
easy
navigation
and
addressing
0~100%
smooth
dimming
and
variable
strobe
speeds
Data
In/Out:
3-‐PIN
XLR
sockets
RDA:
Remote
DMX
addressing,
DMX
address
can
be
remotely
set
up
by
universal
controller
5
Specification:
Power
Voltage:
AC
100~240V,
50/60Hz
Power
Consumption:
134W
Light
Source:
1
x
60W
white
LED
Beam
Angle:
15°
Fuse:
T
6.3A
Dimensions:
292
x
252
x
425mm
Weight:
7.2kgs
6
3.
How
To
Set
The
Unit
3.1
Rear
Panel
1.
LED:
DMX
On
DMX
input
present
MASTER
On
Master
Mode
SLAVE
On
Slave
Mode
SOUND
Flashing
Sound
activation
2.
LED
Display:
Used
to
show
the
various
menus
and
the
selected
functions;
3.
Button:
MENU
To
select
the
programming
functions
DOWN
To
go
backward
in
the
selected
functions
UP
To
go
forward
in
the
selected
functions
ENTER
To
confirm
the
selected
functions
4.
Power
IN/OUT:
Used
to
connect
the
fixture
to
mains
power.
7
5.
DMX
IN:
For
DMX512
link,
use
3-‐pin
XLR
plug
cable
to
link
the
DMX
controller
and
the
fixture,
and
input
the
DMX
signal.
6.
DMX
OUT:
For
DMX512
link,
use
3-‐pin
XLR
plug
cable
to
link
the
next
fixture
and
output
the
DMX
signal.
7.
Fuse
(T
6.3A):
Used
to
protect
the
fixture
from
damage
of
over
current.
8.
Only
For
Remote
Control:
Used
to
connect
with
CA-‐8
to
control
the
fixture
for
Stand
by,
Function
and
Mode
select.
3.2
Main
Function
To
select
any
functions,
press
the
MENU
button
until
the
required
function
is
showing
on
the
display.
Select
the
function
by
pressing
the
ENTER
button
and
the
display
will
blink.
Use
the
DOWN
and
UP
button
to
change
the
mode.
Once
the
required
mode
has
been
selected,
press
the
ENTER
button
to
setup
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
The
main
functions
are
on
the
next
page:
9
DMX
512
ADDRESS
To
select
the
,
press
the
ENTER
button
to
show
the
DMX
ADDRESS
on
the
display.
Use
the
DOWN/UP
button
to
adjust
the
address
from
1
to
512.
Once
the
address
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
CHANNEL
MODE
To
select
the
,
press
the
ENTER
button
to
show
the
DMX
CHANNEL
MODE
on
the
display.
Use
the
DOWN/UP
button
to
select
the
8
CH
or
11
CH
mode.
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
SHOW
MODE
To
select
the
,
press
the
ENTER
button
to
show
the
SHOW
MODE
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(Show
1),
(Show
2),
(Show
3)
or
(Show
4)
mode.
Once
the
show
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
SPLIT
COLOUR
MODE
To
select
the
,
press
the
ENTER
button
to
show
the
SPLIT
COLOUR
MODE
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(split
colour
mode)
or
(normal).
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
10
SLAVE
MODE
To
select
the
,
press
the
ENTER
button
to
show
the
SLAVE
MODE
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(normal),
(2
light
show)
mode.
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
BLACKOUT
MODE
To
select
the
,
press
the
ENTER
button
to
show
the
BALCKOUT
MODE
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(blackout)
or
(normal)
mode.
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
SOUND
MODE
To
select
the
,
press
the
ENTER
button
to
show
the
SOUND
MODE
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(sound
mode
on)
or
(sound
mode
off).
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
SOUND
SENSE
To
select
the
,
press
the
ENTER
button
to
show
the
SOUND
SENSE
on
the
display.
Use
the
DOWN/UP
button
to
adjust
the
sound
sensitivity
from
0
to
100.
Once
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
11
PAN
INVERSION
To
select
the
,
press
the
ENTER
button
to
show
the
PAN
INVERSION
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(pan
inversion)
or
(normal)
mode.
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
TILT
INVERSION
To
select
the
,
press
the
ENTER
button
to
show
the
TILT
INVERSION
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(tilt
inversion)
or
(normal)
mode.
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
LED
DISPLAY
To
select
the
,
press
the
ENTER
button
to
show
the
LED
DISPLAY
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(LED
display
on)
or
(LED
display
off)
mode.
Once
the
mode
has
been
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
DISPLAY
To
select
the
,
press
the
ENTER
button
to
show
the
DISPLAY
on
the
display.
Use
the
DOWN/UP
button
to
select
the
(normal)
or
(display
inversion).
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode:
Display
normal
mode
for
the
fixture
putting
on
the
floor;
Display
inversion
mode
for
the
fixture
fixing
under
ceiling.
12
FOCUS
POSITION
To
select
the
,
press
the
ENTER
button
to
show
the
FOCUS
POSITION
on
the
display.
Then
press
the
ENTER
button
and
the
unit
will
run
the
built-‐in
programmed
for
focus
positioning.
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
FUNCTION
DELAY
To
select
the
,
press
the
ENTER
button
to
show
the
FUNCTION
DELAY
on
the
display.
Use
the
DOWN/UP
button
to
select
the
delay
time,
0
(no
delay)
or
1/2/3
(Wait
for
1/2/3
seconds
before
these
Functions
of
8/11
CH
are
activated/deactivated).
Once
selected,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
DIMMER
CALIBRATION
To
select
the
,
press
the
ENTER
button
to
show
the
DIMMER
CALIBRATE
on
the
display.
Use
the
DOWN/UP
button
to
calibrate
the
dimmer
for
a
maximum
output
from
50
(limited
to
50%
of
the
really
max.
output)
to
100
(maximum
output
is
not
limited).
Once
calibrated,
press
the
ENTER
button
to
setup,
to
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
TEST
To
select
the
,
press
the
ENTER
button
to
show
the
TEST
on
the
display
and
the
unit
will
run
a
self-‐test
.
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
13
TEMPERATURE
To
select
the
,
press
the
ENTER
button
to
show
the
TEMPERATURE
on
the
display
and
the
display
will
show
the
temperature
of
the
unit
.
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
FIXTURE
HOURS
To
select
the
,
press
the
ENTER
button
to
show
the
FIXTURE
HOURS
on
the
display
and
the
display
will
show
the
number
of
working
hours
of
the
unit
.
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
SOFTWARE
VERSION
To
select
the
,
press
the
ENTER
button
to
show
the
SOFTWARE
VERSION
on
the
display
and
the
display
will
show
the
version
of
software
of
the
unit
.
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
DEFAULTS
SETTING
To
select
the
,
press
the
ENTER
button
to
show
the
DEFAULTS
SETTING
on
the
display.
Use
the
DOWN/UP
button
to
select
the
or
.
Once
the
has
been
selected,
press
the
ENTER
button,
and
use
the
DOWN/UP
button
to
select
the
(PRO
Defaults)
or
(AUTO
Defaults)
mode.
For
professional
users,
detailed
explanation
as
followings:
F
à
F
à
F
à
14
F
à
F
à
F
à
F
à
F
à
F
à
F
à
Mostly
automatic
mode,
for
non
professional
users,
detailed
explanation
as
followings:
F
à
F
à
F
à
F
à
F
à
F
à
F
à
F
à
F
à
F
à
(Notice:
Other
settings
are
NOT
changed
while
choosing
Defaults
Setting!)
Press
the
ENTER
button
and
the
corresponding
functions
will
set
to
defaults
setting.
To
go
back
to
the
functions
without
any
changes
press
the
MENU
button
again.
Hold
and
press
the
MENU
button
for
one
second
or
wait
for
one
minute
to
exit
the
menu
mode.
RESET
To
select
the
,
press
the
ENTER
button
to
show
the
RESET
on
the
display.
Press
the
ENTER
button
and
all
channels
of
the
unit
will
return
to
their
standard
position.
15
3.3
Home
Position
Adjustment
—
Pan
home
position
adjustment
To
select
the
,
press
the
ENTER
button
to
show
the
PAN
OFFSET
on
the
display.
Use
the
DOWN
and
UP
button
to
adjust
the
value
from
-‐127
to
127,
press
the
ENTER
button
to
store.
Press
the
MENU
button
to
exit.
—
Tilt
home
position
adjustment
To
select
the
,
press
the
ENTER
button
to
show
the
TILT
OFFSET
on
the
display.
Use
the
DOWN
and
UP
button
to
adjust
the
value
from
-‐127
to
127,
press
the
ENTER
button
to
store.
Press
the
MENU
button
to
exit.
—
Colour
home
position
adjustment
To
select
the
,
press
the
ENTER
button
to
show
the
COLOUR
OFFSET
on
the
display.
Use
the
DOWN
and
UP
button
to
adjust
the
value
from
-‐127
to
127,
press
the
ENTER
button
to
store.
Press
the
MENU
button
to
exit.
—
Gobo
home
position
adjustment
To
select
the
,
press
the
ENTER
button
to
show
the
GOBO
OFFSET
on
the
display.
Use
the
DOWN
and
UP
button
to
adjust
the
value
from
-‐127
to
127,
press
the
ENTER
button
to
store.
Press
the
MENU
button
to
exit.
16
—
Gobo
rotation
home
position
adjustment
To
select
the
,
press
the
ENTER
button
to
show
the
R
GOBO
OFFSET
on
the
display.
Use
the
DOWN
and
UP
button
to
adjust
the
value
from
-‐127
to
127,
press
the
ENTER
button
to
store.
Press
the
MENU
button
to
exit.
4.
How
to
Control
the
Unit
There
are
three
ways
to
control
the
unit:
1.
Master/slave
built-‐in
preprogram
function
2.
Easy
controller
3.
Universal
DMX
controller
No
need
to
turn
the
unit
off
when
you
change
the
DMX
address,
as
the
new
DMX
address
setting
will
be
in
affect
at
once.
Every
time
you
turn
the
unit
on,
it
will
show
“
”
on
the
display
and
move
all
the
motors
to
their
‘home’
position
and
you
may
hear
some
noises
for
about
20
seconds.
After
that
the
unit
will
be
ready
to
receive
DMX
signal
or
run
the
built
in
programs.
4.1
Master/Slave
Built
In
Preprogrammed
Function
By
linking
the
units
in
master/slave
connection,
the
first
unit
will
control
the
other
units
to
give
an
automatic,
sound
activated,
synchronized
light
show.
This
function
is
good
when
you
want
an
instant
show.
You
have
to
set
the
first
unit
in
master
mode
and
select
(show
1),
(Show
2),
(Show
3)
or
(show
4)
mode.
Its
DMX
input
jack
will
have
nothing
plugged
into
it,
and
its
master
LED
will
be
constantly
on
and
sound
LED
will
flash
to
the
music.
The
other
units
will
have
to
be
set
in
slave
mode
and
select
(normal)
or
(2
light
show)
mode.
Their
DMX
cables
plugged
into
the
DMX
input
jacks
(daisy
chain)
and
the
slave
LED
lights
will
be
constantly
be
on.
2-‐light
show
In
slave
mode,
means
the
unit
works
normally
and
means
2-‐light
show.
In
order
to
17
create
a
great
light
show,
you
can
set
on
the
second
unit
to
get
contrast
movement
to
each
other,
even
if
you
have
only
two
units.
4.2
Easy
Controller
The
easy
remote
control
is
used
only
in
master/slave
mode.
By
connecting
to
the
1/4”
microphone
jack
of
the
first
unit,
you
will
find
that
the
remote
controller
on
the
first
unit
will
control
all
the
other
units
for
Stand
by,
Function
and
Mode
selection.
Stand
By
Blackout
the
unit
Function
1.
Sync.
Strobe
2.
Async
strobe
3.
Sound
Strobe
Show
1-‐4
1.
Press
to
select
color
2.
Hold
to
select
gobo
Mode
Sound
(LED
OFF)
Show
(LED
Slow
Blinking)
LED
ON
4.3
DMX
Controller
Using
a
universal
DMX
controller
to
control
the
units,
you
have
to
set
DMX
address
from
1
to
512
channel
so
that
the
units
can
receive
DMX
signal.
Press
the
MENU
button
up
to
when
the
is
showing
on
the
display.
Press
the
ENTER
button
and
the
display
will
blink.
Use
the
DOWN
and
UP
button
to
change
the
DMX512
address.
Once
the
address
has
been
selected,
press
and
keep
the
ENTER
button
pressed
up
to
when
the
display
stops
blinking
or
storing
automatically
7
seconds
later.
To
go
back
to
the
functions
without
any
change
press
the
MENU
button
again.
Please
refer
to
the
diagrams
on
the
next
page
to
address
your
DMX512
channel
for
the
first
4
units.
20
6.
DMX
Connection
Unit
1
Unit
2
Unit
3
Unit
4
1. At
last
unit,
the
DMX
cable
has
to
be
terminated
with
a
terminator.
Solder
a
120
ohm
1/4W
resistor
between
pin
2(DMX-‐)
and
pin
3(DMX+)
into
a
3-‐pin
XLR-‐plug
and
plug
it
in
the
DMX-‐output
of
the
last
unit.
2. Connect
the
unit
together
in
a
`daisy
chain`
by
XLR
plug
from
the
output
of
the
unit
to
the
input
of
the
next
unit.
The
cable
can
not
branched
or
split
to
a
`Y`
cable.
DMX
512
is
a
very
high-‐speed
signal.
Inadequate
or
damaged
cables,
soldered
joints
or
corroded
connectors
can
easily
distort
the
signal
and
shut
down
the
system.
3. The
DMX
output
and
input
connectors
are
pass-‐through
to
maintain
the
DMX
circuit,
when
power
is
disconnected
to
the
unit.
4. Each
lighting
unit
needs
to
have
an
address
set
to
receive
the
data
sent
by
the
controller.
The
address
number
is
between
0-‐511
(usually
0
&
1
are
equal
to
1).
5. The
end
of
the
DMX
512
system
should
be
terminated
to
reduce
signal
errors.
21
6. 3
pin
XLR
connectors
are
more
popular
than
5
pin
XLR.
3
pin
XLR:
Pin
1:
GND,
Pin
2:
Negative
signal
(-‐),
Pin
3:
Positive
signal
(+)
5
pin
XLR:
Pin
1:
GND,
Pin
2:
Negative
signal
(-‐),
Pin
3:
Positive
signal
(+)
Pin
4/5:
Not
used.
7.
Troubleshooting
Following
are
a
few
common
problems
that
may
occur
during
operation.
Here
are
some
suggestions
for
easy
troubleshooting:
A. The
fixture
does
not
work,
no
light
1. Check
the
connection
of
power
and
main
fuse.
2. Measure
the
mains
voltage
on
the
main
connector.
B.
Not
responding
to
DMX
controller
1. DMX
LED
should
be
on.
If
not,
check
DMX
connectors,
cables
to
see
if
linking
properly.
2. If
the
DMX
LED
is
on
and
no
response
to
the
channel,
check
the
address
settings
and
DMX
polarity.
3. If
you
have
intermittent
DMX
signal
problems,
check
the
pins
on
connectors
or
on
PCB
of
the
fixture
or
the
previous
one.
4. Try
to
use
another
DMX
controller.
5. Check
if
the
DMX
cables
run
near
or
run
alongside
to
high
voltage
cables
that
may
cause
damage
or
interference
to
DMX
interface
circuit.
C.
Some
fixtures
don’t
respond
to
the
easy
controller
1. You
may
have
a
break
in
the
DMX
cabling.
2. Check
the
LED
for
the
response
of
the
master/
slave
mode
signal.
D.
No
response
to
the
sound
1. Make
sure
the
fixture
does
not
receive
DMX
signal.
2. Check
microphone
to
see
if
it
is
good
by
tapping
the
microphone.
22
E.
One
of
the
channels
is
not
working
well
1. The
stepper
motor
might
be
damaged
or
the
cable
connected
to
the
PCB
is
broken.
2. The
motor’s
drive
IC
on
the
PCB
might
be
out
of
condition.
8.
Fixture
Cleaning
Cleaning
must
be
carried
out
periodically
to
optimize
light
output.
Cleaning
frequency
depends
on
the
environment
in
which
the
fixture
operates:
moist,
smoky
or
particularly
dirty
surroundings
can
cause
greater
accumulation
of
dirt
on
the
fixture.
Clean
with
soft
cloth
using
normal
glass
cleaning
fluid.
Always
dry
the
parts
carefully.
Clean
the
external
optics
at
least
every
20
days.
Clean
the
internal
optics
at
least
every
30/60
days.
Declaration
of
Conformity
We
declare
that
our
products
(lighting
equipments)
comply
with
the
following
specification
and
bears
CE
mark
in
accordance
with
the
provision
of
the
Electromagnetic
Compatibility
(EMC)
Directive
89/336/EEC.
EN55103-‐1:
2009
;
EN55103-‐2:
2009;
EN62471:
2008;
EN61000-‐3-‐2:
2006
+
A1:2009
+
A2:2009;
EN61000-‐3-‐3:
2008.
&
Harmonized
Standard
EN
60598-‐1:2008
+
All:2009;
EN
60598-‐2-‐17:1989
+
A2:1991;
EN
62471:2008;
EN
62493:
2010
Safety
of
household
and
similar
electrical
appliances
Part
1:
General
requirements
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
English
(Applicable in the European Union and other European countries with seperate
collection systems)
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please
seperate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.
www.prolight.co.uk
Innovation,
Quality,
Performance
