Python 5303 Quick Reference Install Manual

1 Quick Reference Install Guide Security and Remote Start 5303 To Remote Start port Relay satellite port Remote Start port H Bitwriter D2D port Control Center Button LED Shock Sensor port Shock Sensor (side view) Jumper light fash Sensitivity Adjustment Antenna Control Center LED output (use white 2-pin connector from Control Center cable) Control Center button input (use blue 2-pin connector from Control Center cable) Wiring Connections Main Harness (H1), 12-pin connector H1/1 RED/WHITE (-) 200mA AUX TRUNK RELEASE OUTPUT H1/2 RED (+) CONSTANT POWER INPUT H1/3 BROWN (+) SIREN OUTPUT H1/4 NOT USED H1/5 BLACK (-) CHASSIS GROUND INPUT H1/6 VIOLET* (+) DOOR TRIGGER INPUT, ZONE 3 H1/7 BLUE (-) INSTANT TRIGGER INPUT, ZONE 1 H1/8 GREEN* (-) DOOR TRIGGER INPUT, ZONE 3 H1/9 BLACK/WHITE (-) 200mA DOMELIGHT SUPERVISION OUTPUT H1/10 WHITE/BLUE (-) REMOTE START ACTIVATION INPUT H1/11 WHITE (+)/(-) SELECTABLE LIGHT FLASH OUTPUT H1/12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT * The door trigger wire will still need to be connected if the system is programmed with security features OFF to allow the system to enter the programming modes. Heavy gauge relay satellite H/1 PURPLE STARTER OUTPUT TO STARTER (STARTER SIDE) H/2 GREEN STARTER INPUT FROM IGNITION SWITCH (KEY SIDE) H/3 RED (+) 30A HIGH CURRENT 12V INPUT H/4 ORANGE OUTPUT TO ACCESSORY CIRCUIT H/5 RED (+) (30A) HIGH CURRENT 12V INPUT H/6 PINK OUTPUT TO PRIMARY IGNITION CIRCUIT H/7 RED/WHITE (+) (30A) HIGH CURRENT 12V INPUT H/8 PINK/WHITE OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT Relay satellite 4-pin connector 1 BLUE (-) 200mA STATUS OUTPUT 2 ORANGE (-) 200mA ACCESSORY RELAY TURN ON 3 PURPLE (-) 200mA STARTER RELAY TURN ON 4 PINK (-) 200mA IGNITION RELAY TURN ON H3 Harness Remote Start, 5-pin connector H3/1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT H3/2 VIOLET/WHITE TACHOMETER INPUT WIRE H3/3 BROWN (+) BRAKE SHUTDOWN INPUT WIRE H3/4 GRAY (-) HOOD PIN SWITCH INPUT, ZONE 6 H3/5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER - Latched Pulsed Remote Start ribbon harness* 1 PINK/WHITE (-) 200mA PROGRAMMABLE IGN2/ACC2 RELAY TURN ON 2 YELLOW (+) IGNITION INPUT TO ALARM 3 PINK (-) 200mA IGNITION RELAY TURN ON 4 ORANGE (-) 200mA ACCESSORY RELAY TURN ON 5 PURPLE (-) 200mA STARTER RELAY TURN ON 6 ORANGE/BLACK (-) 500mA ANTI GRIND/GROUND WHEN ARMED OUTPUT 7 BLUE (-) 200 mA STATUS OUTPUT *The ribbon harness connects to the heavy gauge relay satellite. H4 AUX 4/Horn, 2-pin connector H4/1 ORANGE/BLACK (-) 200mA AUX 4 OUTPUT H4/2 BROWN (-) 200 mA HORN OUTPUT Door Lock, 3-pin connector 1 BLUE (-) UNLOCK OUTPUT 2 NOT USED 3 GREEN (-) LOCK OUTPUT H2 Harness, 6-pin connector H2/1 BLUE (-) 200mA SECOND UNLOCK OUTPUT H2/2 WHITE/BLACK (-) 200mA AUX 3 OUTPUT H2/3 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT H2/4 GREEN/WHITE (-) 200mA FACTORY ALARM REARM OUTPUT H2/5 GRAY/BLACK (-) WAIT-TO-START INPUT H2/6 LIGHT GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M). Some bitwriters with a date code of 6B do not require the IC upgrade, refer to tech tip # 1112 for more information. The Bitwriter® (p/n 998U) requires chip version 2.7 or newer to program this unit. Installation Points Adjusting the Shock Sensor Important! Make sure the vehicle is disarmed. The shock sensor sensitivity can be adjusted by using a trimmer tool to turn the potentiometer. Adjusting the sensor: 1. Disarm the system, turn the ignition Off. 2. With the sensor mounted in its permanent location, locate the trim pot on the shock sensor module and using a trimmer tool: • Turn the potentiometer clockwise for increased sensitivity or • Turn it counterclockwise for decreased sensitivity Note: You can test the new setting by cautiously impacting the vehicle with in- creasing intensity while noting the LED status on the shock sensor. The LED turns on for a short duration for small impacts before turning off (indicating a warn- away trigger). The impact level required to fully trigger the alarm is indicated when the LED remains on for a longer duration before turning off. Tach Learning To learn the tach signal: 1. Start the vehicle with the key. 2. Within 5 seconds, press and hold the control center button. 3. After 3 seconds the LED will light constant when the tach signal is learned. 4. Release the control center button. Important: This unit can learn the tachometer with the analog input or through D2D using an interface module. The unit confirms which source is used. When programming tach learning with: • Analog, the parking lights flash one time • D2D inerface module, the parking lights flash twice If the tachometer input on the system is connected to the vehicle, the D2D tachometer input will be ignored. Virtual Tach Note: Virtual tach is not recommended for diesel trucks To program Virtual Tach: 1. After the install is complete, remote start the car. 2. If the car does not start on the first attempt, let the remote start attempt again. 3. Once the car starts, let it run until the parking lights come on. 4. When the parking lights come on, shut off the remote start with the remote - that’s it! Virtual Tach is programmed. Virtual Tach handles disengaging the starter motor during remote starting – it does not address over-rev. If the customer wants to have the over-rev protection capabil- ity, the tach wire must be connected. This may involve more installation shop charges than initially quoted. Important: If the Virtual Tach mode over cranks or doesn't crank the vehicle long enough to start and run the car, use the Bitwriter to add or subtract the starter output time. You can adjust the output time in incre- ments of 50msec of the learned time using the Bitwriter. Reset and Deletion If a feature/virtual tach needs to be reset or the remote controls need to be deleted, use the following procedure. 1. Open a door. (The GREEN wire, H1/8, or the VIO­LET, H1/6 must be con- nected.) 2. Turn the ignition to the ON position (The heavy gauge pink wire must be con- nected). 3. Within 10 seconds, press and release the control center button: 2 times if you want to delete remotes, 3 times to reset features or 4 times to reset virtual tach. These features are described next. Delete remotes: This feature erases all remotes from the memory of the security system. This is useful in cases when a customer’s remote is lost or stolen. Note: This does not reset the programmed features of the security system or reset the Virtual Tach setting. Reset Features: This resets all features of the security system to the factory default settings. Note: This feature does not delete the remotes from the security system or reset the Virtual Tach setting or security features enabled/disabled settings Virtual Tach Reset: Deletes all previously learned values for Virtual Tach, and on the next remote start sequence the unit begins virtual tach initial- ization. Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach setting. 4. Once you have selected the function step, press the control center button once more and hold it. The LED flashes and the siren chirps to confirm the selected functional step. Do not release the control center button 5. While holding the control center button, press the AUX button on the remote control. The unit chirps to confirm that the feature has been successfully reset. Once the feature is reset, the control center button can be released. Remote Start Shutdown Diagnostics To perform shutdown diagnostics: 1. With the ignition Off, press and hold the control center button. 2. Turn the ignition On and then back Off while holding the control center button. 3. Release the control center button. 4. Press and release the control center button. The LED flashes to report the last shutdown for one minute or until the ignition is turned on, as shown in the following table: LED Flashes Shutdown Mode 1 flash Timed out 2 flashes Over-rev shutdown 3 flashes Low or no RPM, low battery (voltage and virtual tach modes) 4 flashes Transmitter shutdown (or optional push button) 5 flashes (-) Hood Shutdown (H3/4 GRAY) 6 flashes (+) Shutdown (H3/3 BROWN) 7 flashes (-) Neutral safety shutdown (H3/1 BLACK/WHITE) 8 flashes Wait-to-start timed out See full Installation Guide for more detailed information on this system. Such information and more can be found online at: www.directechs.com Logo, Directed Electronics w-driven.eps Logo, Directed with designed in USA.eps Logo, Directed with Distributed By.eps Directed Logo Usage Guide Translations For a Spanish version of the Installation Guide, please download it from www. directechs.com under Resources. Estimado Cliente: Si buscas los guías de instalación, por favor de bajar lo del Resources en el sitio www.directechs.com

2 QRN5303 2011-12 Programming System Features Note: When doing any programming with security features off, the horn function (feature menu 1 item 13) must be programmed as Siren function to get an audible confirmation from the unit. The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the feature settings using the control center button. 1. Open a door. 2. Turn the ignition on, then off. 3. Select a Menu. Press and hold the control center button. The number of siren chirps indicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu 2 and 3 chirps for menu 3. 4. When the desired menu chirps are heard, release the control center button. 5. Select a Feature. Press and release the control center button the number of times corresponding to the feature you wish to change. Then press and hold one more time to select the features. 6. Program the Feature. While holding the Control center button, you can program the feature using the remote control. For features with only two options; AUX = option 1 while AUX = option 2. For features with more than two options; AUX selects the options in ascending order. Once a feature is programmed: • Other features can be programmed within the same menu • Another menu can be selected • The learn routine can be exited if programming is complete To access another feature in the same menu: 1. Press and release the control center button the number of times necessary to advance from the feature you just programmed to the next one you want to program. 2. Then press the control center button once more and hold it. To select another menu: 1. Press and hold the control center button. 2. After 3 seconds, the unit advances to the next menu and the siren chirps, indi- cating which menu has been accessed. The learn routine exits if any of the following occurs: • The open door is closed • The ignition is turned On • There is no activity for 30 seconds • The control center button is pressed too many times Security Features Disable/Enable The system has the ability to function as a security/remote start system or keyless/ remote start system by enabling or disabling security. The default setting is Enabled. To program the feature. 1. Open a door. 2. Turn the ignition on, then off. 3. Press and hold the control center button until the LED flashes 3 times and the siren (if connected) chirps 3 times. 4. Release the control center button. Note: If the control center button is released and then pressed again, the sys- tem will enter the features programming menus. 5. Within 15 seconds, simultaneously press the AUX and AUX buttons of a pro- grammed remote control. 6. The siren (if connected) will chirp and the parking lights will flash as listed below 1 flash/chirp: Security features disabled 2 flashes/chirps: Security features enabled Security Features Disabled will disable all security operations of the system, includ- ing but not limited to those listed below: • Multi Level Arming • Sensor Warn-away • Full Trigger Operation • Armed While Driving • Automatic Engine Disable Note: Disabled features with programmable options can still be programmed manu- ally or with the Bitwriter but will not operate until the Security Features have been enabled. The Security Features Disable/enable routine exits if the following occurs: • The open door is closed • The ignition is turned on • There is no activity for 15 seconds • The control center button is pressed too many times Bitwriter - Only Options If programming with the Bitwriter®, the learn routine can be locked or un- locked. If the learn routine has previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the control center but- ton. The Bitwriter® gives you access to a wider range of system options. These features and the adjustments that may be programmed are described in the table below. Menu Item Feature Default Options 1 Siren Duration 30 sec. 1-180 sec. 2 Aux 2 Timed Output 30 sec. 1-90 sec. 3 Aux 3 Timed Output 30 sec. 1-90 sec. 4 Aux 4 Timed Output 30 sec. 1-90 sec. 5 Engine Runtime 12 min. 1-60 min. 6 Diesel Start Delay 15 sec. 1-90 sec. 7 Timer Mode Runtime 12 min. 1-16 min. 8 Virtual Tach Fine Tune Not initialized 0-1000 in 50 millisecond increments 9 Transmitter Programming Unlocked Locked 10 Feature Programming Unlocked Locked Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach or security features enabled/disabled settings Red 4-pin port, Bitwriter/ESP2 or D2D programming The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port. The factory default is Bitwriter/ESP2 mode. To use as D2D mode follow the below steps: 1. Make sure White/Blue activation wire is grounded. 2. Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode change. 3. Remove the White/Blue wire from ground. To change from D2D to Bitwriter/ESP2 mode: 1. Make sure the White/Blue activation wire is grounded. 2. Power the unit up, the system LED turns on solid for 5 seconds to confirm Bit- writer/ESP2 mode change. 3. Remove the White/Blue wire from ground. The procedure can be repeated to toggle from one mode to the other. Important: If you power up the system with the White/Blue activation wire ungrounded, the system LED will come on solid for 5 seconds indi- cating the system is in Bitwriter/ESP2 mode. Feature Menus Default settings are in bold type. Menu 1 - Basic Menu Item One-chirp setting Two-chirp setting 1 Active Arming Passive arming 2 Arm/disarm chirps on Arm/disarm chirps Off 3 Ignition lock On Ignition lock Off 4 Ignition unlock On Ignition unlock Off 5 Active locking only Passive locking 6 Panic with ignition On No panic with ignition On 7 0.8 second door lock pulses (1) 3.5 (2), 0.4 (3) seconds 8 Forced passive arming on Forced passive arming off 9 Automatic engine disable on Automatic engine disable off 10 Armed When Driving (AWD) On AWD Off 11 Code Hopping On Code Hopping off 12 Horn Output Pulsed Constant 13 Horn function Full Alarm Only (1) Siren function - chirp length 20ms (2), 30ms (3), 40ms (4), 50ms (5) 14 Comfort Closure ON (1) Comfort Closure OFF (2) Comfort Closure 2 (3) Menu 2 - Advanced Menu Item One-chirp setting Two-chirp setting 1 30 second siren duration 60 second siren duration 2 Nuisance Prevention Circuitry On Nuisance Prevention Circuitry OFF 3 Progressive door trigger Instant door trigger 4 Disarm from Valet, 1 pulse Disarm from Valet, 2-5 pulses 5 Door trigger error chirp ON Door trigger error chirp OFF 6 Ignition controlled domelight On Ignition controlled domelight OFF 7 Unlock output 1 pulse Unlock output 2 pulses 8 Lock output 1 pulse Lock output 2 pulses 9 Factory disarm with trunk release ON Factory disarm with trunk release OFF 10 FAD function with Unlock (1) Before Unlock (2), Remote Start only (3) 11 FAD 1 pulse 2 pulses 12 AUX 2 validity (1) Latched (2), Latch reset with ignition (3), 30-secs timed (4), 60-secs (5), 90-secs (6) 13 AUX 2 Linking None (1) Arm (2), Disarm (3), Remote Start (4) 14 AUX 3 validity (1) Latched (2), Latch reset with ignition (3), 30-sec. timed (4)60sec(5)90sec(6) 15 AUX 3 linking None (1) Arm (2), Disarm (3), Remote Start (4) 16 AUX 4 validity (1) Latched (2), Latch reset with ignition (3), 30-sec. timed (4) 60sec (5) 90 (6) 17 AUX 4 linking None (1) Arm (2).Disarm (3), Remote Start (4) Menu 3 - Remote start Menu Item One-chirp setting Two-chirp setting 1 Engine checking: Virtual Tach Voltage(2), OFF(3), Tachometer(4) 2 Remote start runtime: 12 min 24 min, 60 min 3 Parking light output: Flashing Constant 4 Cranking time: 0.6 sec 0.8, 1.0, 1.2, 1.4, 1.6, 1.8, 2.0, 4.0 second 5 Activation pulse 1 2 6 2nd Ignition/Acc output: Ignition Accessory 7 Acc state during wait-to-start Off On 8 2nd status output: Normal Rear defogger: latch 10 min. rear defogger pulse 9 Anti grind: On Off 10 Diesel timer: Wait-to-Start input Timed 15 , 30 ,45 seconds 11 Timer mode run time: 12 min 3, 6, 9, min 12 Timer mode: Timed starts Temp starts 13 Short run (turbo): 1 min 3,5, 10 min Remote Programming 1. Open a door 2. Turn key to the ON position 3. Within 5 seconds, press and release the control center button one time. 4. Within 5 seconds, press and hold the control center button. The LED will flash one time and the siren chirps to confirm entry into remote programing. 5. Press the AUX button on the remote control. 6. The siren will chirp to confirm the remote has been programmed. 7. Release the control center button. 8. The siren will emit one long chirp confirming that remote programming has been exited. The programming routine exits if any of the following occurs: The open door is closed The ignition is turned off There is no activity for 30 seconds The control center button is pressed too many times Basic Remote Functions Button Function A U X ARM A U X DISARM AUX AUX REMOTE START AUX TRUNK RELEASE Note: See Owner’s guide for more details Long Term Event History The system stores the last two full triggers in memory. These are not erasable. Each time the unit sees a full trigger, the older of the two triggers in memory is replaced by the new trigger. To access long term event history: 1. With the ignition Off, press and hold the control center button. 2. Turn the ignition On. 3. Release the control center button. 4. Within 5 seconds, press and release the control center button. The LED flashes in groups indicating the last two zones that triggered the unit for 1 minute or until the ignition is turned off. Refer to table of zones. Note: The Warn Away triggers are not stored to memory and is not reported. Table of Zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input. Zone Trigger Type Input Description 1 Instant Trigger BLUE (H1/7) 2 Multiplexed Shock Sensor Input Mux BLUE sensor port wire. 3 Door Trigger GREEN (H1/8) and VIOLET (H1/6). 4 Multiplexed Shock Sensor Input Mux GREEN wire 5 Ignition Yellow ribbon harness wire 6 Hood Trigger GRAY on the 6-pin shutdown harness