Symbol DS6708 Quick Start Manual

Enter Key (Carriage Return/Line Feed) Set Defaults IBM 46XX Host Types USB Host Types RS-232 USB 3 2 1 IBM 46XX Keyboard Wedge Host Types Level POST IN WORK AREA POST IN WORK AREA Quick Start Guide ACCESSORIES CORD ATTACHMENT/REMOVAL See Product Reference Guide for detailed information HOST INTERFACES NOTE: Cables may vary depending on configuration TROUBLESHOOTING No power to scanner Check system power; ensure power supply, if required, is connected Incorrect interface cable used Ensure that correct interface cable is used Ensure all cable connections are secure Scan appropriate host parameter bar codes Ensure all cable connections are secure Interface/power cables are loose Scanner not working Bar code unreadable Ensure bar code is not defaced; try scanning test bar code of same bar code type Distance between scanner and bar code incorrect Move scanner closer to or further from bar code Scanner not programmed for bar code type Ensure scanner is programmed to read type of bar code being scanned Scanner not decoding bar code Scanner not programmed for correct host interface Interface cable is loose Scanner decoding bar code, but data not transmitting to host Scanner not programmed for correct host interface Scan appropriate host parameter bar codes Scanned data incorrectly displayed on host SYMBOL DS6708 PROGRAMMING BAR CODES 1 LED Indicators 2 Scan Window 3 Scan Trigger IntelliStand Desk Cup Wall Mount SET DEFAULTS HID KEYBOARD EMULATION IBM HAND-HELD USB ICL RS-232 NIXDORF RS-232 MODE A NIXDORF RS-232 MODE B FUJITSU RS-232 OPOS/JPOS Keyboard Wedge IBM PC/AT and IBM PC COMPATIBLE PORT 5B PORT 9B STANDARD RS-232 LEVEL

SYMBOL DS6708 3 2 1 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 LASER LIGHT- DO NOT STARE INTO BEAM . CLASS 2 LASER PRODUCT. LASERSTRAHLUNG - NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2. LUMI»RE LASER - NE PAS REGARDER DANS LE FAISCEAU. APPAREIL ¿ LASER DE CLASSE 2 630-680nm, 1mW OPTIMUM ARM POSITION AVOID EXTREME WRIST ANGLES Low/medium/high beep Power up Short medium beep Bar code decoded 4 long low beeps Transmission error detected; data is ignored Standard Use High/low beep Correct programming sequence performed Low/high beep Incorrect programming sequence or “Cancel” bar code scanned High/low/high/low beep Successful parameter setting Parameter Menu Scanning BEEPER INDICATIONS LED INDICATIONS Off Scanner is on and ready to scan, or no power to scanner Green Bar code is successfully decoded Red Transmission error Local Contact: OPTIMUM SCANNING 1 LED Indicators 2 Scan Window 3 Scan Trigger AVOID BENDING AND REACHING Tested to comply with FCC Standards FOR HOME OR OFFICE USE REGULATORY INFORMATION Ergonomic Recommendations Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury. • Reduce or eliminate repetitive motion • Maintain a natural position • Reduce or eliminate excessive force • Keep objects that are used frequently within easy reach • Perform tasks at correct heights • Reduce or eliminate vibration • Reduce or eliminate direct pressure • Provide adjustable workstations • Provide adequate clearance • Provide a suitable working environment • Improve work procedures. Regulatory Information Symbol Technologies, Inc., the Enterprise Mobility business of Motorola, Inc. ("Motorola"). All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol Technologies, could void the user's authority to operate the equipment. Radio Frequency Interference Requirements Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Interference Requirements – Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Marking and European Economic Area (EEA) Statement of Compliance Symbol Technologies, Inc., hereby declares that this device is in compliance with all the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may be obtained from http://www.motorola.com/enterprisemobility/doc. Laser Devices Symbol products using lasers comply with US 21CFR1040.10 and1040.11 except for deviations pursuant to laser notice no. 50, dated June 24, 2007 and IEC 60825-1 (Ed. 2.0), EN60825-1:2007. The laser classification is marked on one of the labels on the product. Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations: Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure. Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. Scanner Labeling AVOID REACHING AVOID BENDING Recommended Usage Guide AVOID EXTREME WRIST ANGLES 72-83973-01 Revision C March 2010 Alternate left and right hands taking breaks and task rotation recommended Alternate left and right hands taking breaks and task rotation recommended Aiming MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc. 2010 123SCAN2 123Scan2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup via a bar code or USB cable. For more information, visit: http://www.motorola.com/123Scan2. © 2010 MOTOROLA, INC. All rights reserved. Motorola reserves the right to make changes to any product to improve reliability, function, or design. Motorola does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Motorola products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Motorola products. MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered trademarks of Motorola, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Warranty For the complete Motorola hardware product warranty statement, go to: http://www.motorola.com/enterprisemobility/warranty. Service Information If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Motorola Enterprise Mobility Support at: http://www.motorola.com/enterprisemobility/contactsupport. For the latest version of this guide go to: http://www.motorola.com/enterprisemobility/manuals. Power Supply Use ONLY a LISTED Motorola, Type no. 50-14000, or PWRS-14000, Direct Plug-In power supply, marked Class 2 or LPS, or SELV, Rated 5 Vdc, 850 m A Min. (IEC 60950-1). Use of alternative power supply will invalidate any approvals given to this device and may be dangerous.