Airlogic ABM-600 Application Note

Copyright © 2004 AirLogic Co., Ltd. All specification are preliminary and AirLogic reserves the right to change these without notice. http://www.airlogic.co.kr ABM-600 Class1 Bluetooth Module Production Information Data Sheet ID : ABM-600-1XXXX AUG.2004 Rev 1.0 1. Module Features -Bluetooth® V1.2 Compliant -Transmit Power +20dBm(Class1) -2.7V to 3.6V Operation -Full Bluetooth data rate over UART and USB -Four low power modes : Park, Sniff, Hold and Deep Sleep -Support for up to seven slaves -Enhanced Data Rate(EDR) compliant with V0.9 of specification for both 2Mbps and 3Mbps modulation modes 2. General Description ABM-600-1xxxx is a Class1 surface mountable Bluetooth® Module for Notebook PC, Desktop PC, Access Point, Serial Adapter applications. It provides fully compliant Bluetooth system for data and voice communications. Physical interface to host (UART, USB) can support full Bluetooth data rate 723.2k/57.6kbps. A-Law, µ-Law,13bit or 16bit linear PCM, 8k sample/sec synchronous bidirectional audio interface is also available. 4. Features -Size(28.2 X 15 X 2.8mm) -Class1 Support(+20dBm) -Surface Mountable -Support PCM interface for SCO 5. Specification -Operating Conditions Supply Voltage……. VDD: 2.7V ~3.6V Temperature Range….…..… -20~+70°C -Radio Characteristics Receiver Sensitivity … -88dBm Transmitter Power ….. +16.0dBm(Typical) 3. Application -Laptop and Desktop PCs -Access point -Serial Adapter -Personal Digital Assistants (PDAs) -Domestic and Industrial Applications

Copyright © 2004 AirLogic Co., Ltd. All specification are preliminary and AirLogic reserves the right to change these without notice. http://www.airlogic.co.kr 6. Electrical Characteristics Absolute Maximum Ratings Parameter Min Max Unit Storage Temperature -40 +85 °C Supply Voltage(VDD) 2.7 3.6 DCV Supply Voltage(PVCC) 3.0 3.0 DCV Other Pin Voltage Vss-0.4 VDD+0.4 DCV Recommended Operating Conditions Parameter Min Max Unit Temperature -20 +70 °C Supply Voltage for UART 3.0 3.6 DCV Supply Voltage USB 3.1 3.6 DCV 7. RF Specification Transmitter Performance Parameter Condition Min Typ Max Unit Output Power Normal/extreme test - 16 20 dBm Power Density Normal/extreme test - - 20 dBm Power Control Normal/extreme test 2dB ≤ Step size ≤ 8dB Frequency Range Normal/extreme test 2400 - 2483.5 MHz 20dB Bandwidth Normal/extreme test - 850 1000 KHz ±2MHz - - -20 dBm ±3MHz - - -40 dBm Adjacent channel power ±4MHz - - -40 dBm ∆F1avg 140 - 175 KHz ∆F2max 115 - - KHz Modulation Characteristics ∆F2avg / ∆F1avg - - 80 % Initial Carrier Frequency Tolerance -75 - 75 KHz One slot packet(DH1) -25 - 25 KHz Three slot packet(DH3) -40 - 40 KHz Carrier Frequency Drift five slot packet(DH5) -40 - 40 KHz Transceiver Performance Parameter Condition Min Typ Max Unit 30MHz-1GHz - - -36 dBm 1GHz-12.75GHz - - -30 dBm 1.8GHz-5.3GHz - - -47 dBm Out-of-Band Spurious Emissions 5.1GHz-5.3GHz - - -47 dBm Receiver Performance Parameter Condition Min Typ Max Unit Sensitivity level Single slot packets -70 -83 - dBm Sensitivity level Multi slot packets -70 - - dBm C/I co-channel - - 11 dB C/I1MHz (Adjacent channel selectivity) - - 0 dB C/I2MHz (2nd Adjacent channel selectivity) - - -30 dB C/I performance C/I≥3MHz (3rd Adjacent channel selectivity) - - -40 dB 30MHz-2000MHz -10 - - dBm 2000MHz-2400MHz -27 - - dBm 2500MHz-3000MHz -27 - - dBm Blocking performance 3000MHz-12.75MHz -10 - - dBm Intermodulation Performance n=5 -39 - - dBm Maximun Input Level -20 -10 - dBm

Copyright © 2004 AirLogic Co., Ltd. All specification are preliminary and AirLogic reserves the right to change these without notice. http://www.airlogic.co.kr 8. Pin Description Pin No. Pin Name Description 1 GND Common ground 2 PVCC Power Amp Power Supply(3.0V) 3 AIO(0) Programmable I/O terminal 4 AIO(1) Programmable I/O terminal 5 PIO(0) Programmable I/O terminal, RX Enable 6 PIO(1) Programmable I/O terminal, TX Enable 7 PIO(2) Programmable I/O terminal, USB_PULL_UP 8 PIO(3) Programmable I/O terminal, USB_WAKE_UP 9 PIO(4) Programmable I/O terminal, USB_ON 10 GND Common ground 11 PIO(5) Programmable I/O terminal, USB_DETACH 12 PIO(6) Programmable I/O terminal, CLK_REQ 13 PIO(7) Programmable I/O terminal 14 PIO(8) Programmable I/O terminal 15 PIO(9) Programmable I/O terminal, Active Low Reset 16 RESET_IN Module Reset INPUT, Active Low Reset 17 VDD Core & Baseband Power Supply( 2.8, 3.0, 3.3V) 18 GND Common ground 19 GND Common ground 20 USB+ USB Data plus 21 USB- USB Data minus 22 PCM_SYNC Synchronous data strobe 23 PCM_IN Synchronous 8Kss-1 data input 24 PCM_OUT Synchronous 8Kss-1 data output 25 PCM_CLK Synchronous data clock 26 UART_RX UART Data in 27 UART_TX UART Data out 28 UART_RTS UART ready to send 29 GND Common ground 30 UART_CTS UART clear to send 31 SPI_MOSI Serial Peripheral Interface data input 32 SPI_CSB Chip select for Synchronous Serial Interface active low 33 SPI_CLK Serial Peripheral Interface clock 34 SPI_MISO Serial Peripheral Interface data output 35 PIO(11) Programmable I/O terminal 36 PIO(10) Programmable I/O terminal 37 RF-IN_OUT Connect to Antenna 38 GND Common ground

Copyright © 2004 AirLogic Co., Ltd. All specification are preliminary and AirLogic reserves the right to change these without notice. http://www.airlogic.co.kr 9. UART Interface ABM-600-1xxxx Universal Asynchronous Receiver and Transmitter(UART) interface provides a simple mechanism for communicating with other serial device using the RS232 standard. When ABM-600-1xxxx is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The remaining two signal, UART_CTS, UART_RTS, can be used to implement RS232 hardware flow control where both are active low indicators. All UART connections are implemented using CMOS technology and have signaling levels of 0V and VDD * When BCSP protocol is selected for Host Interface, CTS/RTS signal can be omitted

Copyright © 2004 AirLogic Co., Ltd. All specification are preliminary and AirLogic reserves the right to change these without notice. http://www.airlogic.co.kr 10. USB Interface ABM-600-1xxxx USB devices contain a full speed(12Mbit/s) USB interface that is capable of driving of a USB cable directly. No external USB transceiver is required. The device operates as a USB peripheral, responding to requests from a master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented behave as specification V1.2 As USB is a Master/Slave oriented system(in common with other USB peripherals), ABM-600- 1xxxx only supports USB slave operation. ABM-600-1xxxx features an internal USB pull-up resistor. This pulls the USB+ pin weakly high when ABM-600-1xxxx is ready to enumerate. It signal to the PC that it is a full speed(12Mbit/s) USB device.