Camos CM-800D Instruction Manual

Thank you for purchasing this product. For proper usages and application, Please read this instruction manual thoroughly. PRINTED IN KOREA ver. 1.0

TERMS OF PART REMOTE CONTROL FUNCTIONS CONNECTIONS CHANGING REMOTE CONTROL BATTERY SPECIFICATIONS ................................................................... 3 ....................................................................... 5 ........................ 5 ................................................................. 6 ........................................................... 7 ........................................................................ 8 ................................................................ 12 ................ 14 ............................................................. 15 8” TFT LCD DIGITAL COLOR MONITOR WARNING This information is for preventing bodily harm or even death and use should follow this safety rules. SAFEGUARD INSTRUCTIONS Please read the “Safety Rules” carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product. It is very important to follow these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a damage associated with the misuse of the product. This information is for preventing damage or shorten the life time of the products. CAUTION CAUTION While stop driving (parking), set the car in motion. - It may cause battery discharge. Do not use multi socket or extended adaptor. - It may cause unexpected heating, fire and malfunction. Unplug product when do not use for a long time. - It may case fire by short circuit due to heating. Do not place near magnet. - It may cause malfunction and trouble. Should install while power off. (After install products, connect DC jack) - It may cause to electronic shock or malfunction. Do not push a LCD panel. - It may cause LCD broken. In case of inserting battery, attend to polarity and insert according to direction. - When wrong inserting, it may cause fire, damage by explsion. Before install the body, take enough place at least more than 15cm from the wall to emit heat. The battery for remote controller is not rechargeable and should replace same or simi- lar model. Used battery may cause environmental pollution, so trash it carefully. - This may cause a malfunction and problem.

- It may cause to electronic shock or malfunction. Do not put the product in place where sudden temperature increasing and should use on optimum voltage, temperature and humidity. - It may cause to electronic shock or malfunction. Do not place near of air bag effective range. - It may cause malfunction of air bag or accident, injury due to hitting monitor by air bag. Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord. - It may cause cord malfunction, electronic shock and fire. Keep clean dust on power socket. - It may cause electronic shock and fire by bad connection. Do not clean exterior with volatility or oily solvent. Neither keep touching rubber and plastic for long time. - It may cause change of surface, fall of paint, malfunction and fire. When clean exterior, power off and wipe with dry cloth. - Wet cloth may cause a electronic shock. Do not place where vibration and shock. - It may cause throw down and then malfunction and accident. Do not put metals as like pin and needle into hole and chink of grill, speaker. - In case of inserting them, stop to operate, it may cause electronic shock, fire and malfunction. Do not use in problem condition as like smoking, smell something burn. - It may cause fire. Stop to use and make inquiries to agency. Do not disassemble, repair and remodeling. - It may cause malfunction and injury, can not get warranty. - Make inquiries to agent for repair and checkup. 1 8” TFT LCD DIGITAL COLOR MONITOR ※ To safely use the product, please read the user’s manual carefully before use. 1) Connect all lines as directed in the product connection map in the manual. 2) Use the product at the temperature range of -10℃ ~ 60℃. 3) Screen may be a little dark when the product is operated in low temperature areas. 4) Screen will show normal luminosity after a few minutes. 5) When you install the product in a car, do not set a volume level too loud for others to hear outside. 6) Quality of pictures on screen may vary depending on the radio field strength in different locations. 7) You should use video equipment where you experience weak radio field strength. 8) Follow traffic laws when you use the Navigation Route System. BEFORE USE 2 8” TFT LCD DIGITAL COLOR MONITOR • Digital TFT Wide LCD with high resolution and low reflection • All electronic control functions • Convenient Graphic OSD • All functions are displayed on screen (OSD function) • Auto recognition function of TV signal system (PAL/ NTSC/ AUTO) • PC auto adjustment • 7 Languages on OSD menu (ENG-FRA-DEU-ESP-ITA-JPN-KOR) • Auto mode selection (DSUB ANALOG, DVI DIGITAL, AV, S-VIDEO) • One-touch Dimmer (Remote control) • 0.5Watt speaker built-in • STAND-BY function • Low power consumption SPECIAL FEATURES OF THE PRODUCT

TERMS OF PART 4 8” TFT LCD DIGITAL COLOR MONITOR REMOTE CONTROL ① POWER ② TV/AV ③ ▲▼CH ④ MENU ⑤ ◀▶VOL ⑥ PICTURE ⑦ SETUP ⑧ SOUND ⑨ MUTE ⑩ RECALL ⑪ AUTOPIC ⑫ SLEEP ⑬ CH.SET ⑭ A.MEMO ⑮ 0~9 KEY Power On/Off Select DSUB ANALOG/ EXTERNAL VIDEO/ S-VIDEO Selects channel and moves to MENU Selects menu and changes function Controls Volume and changes MENU level Picture selection button Setup selection button Sound selection button For muting sound. Returns to the previous sound level when you push again Displays present status and volume level Selects DYNAMIC, NORMAL, MILD, USER for PICTURE No use button No use button No use button No use button ① ④ ⑦ ② ⑥ ③ ⑤ ⑧ ⑨ ⑮ ⑫ ⑪ ⑩ ⑭ ⑬ ① ④ ② ⑥ ③ ⑤ ① MODE ② MENU ③ DOWN ④ UP ⑤ POWER ⑥ Remote Sensor Window AV/S-VIDEO/PC(RGB) selection function. Press the mode button to be appeared source select OSD box and press the DOWN, UP button or mode button repeatedly th press the menu button or wait 3 second to select highlighted source. * If PC picture size does not match with full horizontal or vertical screen size, press the mode button continuously(2~3 second) and wait for a little while then you can see the most appropriate screen. Button to Setup Screen and Function.Press the menu button to be ap- peared Menu OSD box and press the mode button repeatedly to select the main menu(Picture menu, Setup menu, Audio menu), then press the DOWN or UP button to enter to sub menu, press the mode button repeatedly to highlight icon that user wants, press the DOWN, UP but- ton to increase, decrease or change the function. Push the Menu button once to return to the main menu to select another function or press twice to exit from the OSD. Select the sub menu, decrease the selected function, hot key for volume down. Select the sub menu, increase the selected function, hotkey for volume up. Power On/Off Sensor for receiving signal from the remote control

* ( ), it means a remote control button. FUNCTIONS POWER ON/OFF 1 • POWER ON/OFF KEY 1) Push POWER(POWER) button. POWER is on. 2) Push POWER(POWER) button again. POWER is OFF. MODE (TV/AV) 2 • It is function to change external video signals to DSUB ANALOG/ VIDEO/ S-VIDEO * Adjust it with CH ▲▼ * Adjust it with MODE (Key button) MENU (MENU) 3 • AV/ S-VIDEO PICTURE(PICTURE) - + - + - + - + - + PICTURE SETUP BRIGHTNESS CONTRAST SHARPNESS COLOR TINT COLOR TONE SYSTEM 55 40 14 50 60 AUTO NTSC PAL 1) BRIGHTNESS 2) CONTRAST 3) SHARPNESS 4) COLOR TINT 5) COLOR TONE 6) SYSTEM Adjust the brightness of VIDEO without affecting DSUB ANALOG’s bright- ness. Adjust the contrast of VIDEO without aff ecting DSUB ANALOG’s contrast. Adjust the sharpness of video image. Change the richness of color. Change the tone of color. Change broadcast system NTSC, PAL, AUTO * With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. SETUP (SETUP) ▶ ENGLISH - + - + - + - + ▶ OFF PICTURE SETUP SOUND LANGUAGE OSD TIME TRANSLUCENT OSD H POS. OSD V POS. FACTORY RESET 10 14 50 50 1) LANGUAGE 2) OSD TIME 3) TRANSLUCENT 4) OSD H POS. 5) OSD V POS. 6) FACTORY RESET Change language English, French, German, Spanish, Italian, Japanese, Korean. The number of seconds that the OSD will remain visible before dis- appearing. Change the opaqueness of the background of the OSD. Move the OSD Window to the horizontal direction. Move the OSD Window to the vertical direction. A factory default reset will clear all of OSD information. * With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. 1) MUTE 2) VOLUME 3) TREBLE 4) BASS Mute the sound temporarily. Mute is released when you change channel and adjust volume. Adjust the sound volume. Emphasize high frequency audio. Emphasize low frequency audio. DSUB ANALOG/ AV/ S-VIDEO DSUB ANALOG AV S-VIDEO SOURCE DSUB ANALOG/ DVI DIGITAL/ AV1/ AV2 DSUB ANALOG AV1 AV2 SOURCE SOUND (SOUND) - + - + - + PICTURE SETUP SOUND MUTE VOLUME TREBLE BASS 10 50 50 ▶ OFF * With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. The audio input level should be met with the specification because of the audio distorition.

The color temperature could be changed based on the lcd specification. • DSUB ANALOG PICTURE 1) BRIGHTNESS 2) CONTRAST 3) H POSITION 4) V POSITION 5) PHASE 6) PIXEL FREQ. Adjust the brightness of DSUB ANALOG without affecting AV/ S-VIDEO’s brightness. Adjust the contrast of DSUB ANALOG without aff ecting AV/ S-VIDEO’s con- trast. Adjust the horizontal position of the image. Adjust the vertical position of the image. Remove the noises. When phase value is wrong, the image has vertical lines especially in 1 dot on and off . Adjust the sampling frequency of DSUB analog signal. * With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit. COLOR 1) 9300K 2) 7300K 3) 6500K 4) USER Change color temperature : Red 42 Green 52 Blue 50 Change color temperature : Red 51 Green 46 Blue 46 Change color temperature : Red 40 Green 54 Blue 54 User customizable. (RED, GREEN, BLUE) The tone of color can be changed from red-dish white to bluish white. The individual color components are also user customizable. PICTURE COLOR SETUP 9300K 7300K 6500K USER RED GREEN BLUE - + - + - + 50 50 50 - + - + - + - + - + - + PICTURE COLOR SETUP SOUND BRIGHTNESS CONTRAST H POSITION V POSITION PHASE PIXEL FREQ. 75 50 50 50 14 100 DISPLAY MODES For the display modes listed below, the screen image has been optimized during manu- facture. MODE VGA SVGA 800 x 600 800 x 600 37.880 46.875 60.300 75.000 40.000 49.500 720 x 400 640 x 480 640 x 480 31.469 31.469 37.500 70.087 59.940 75.000 28.322 25.175 31.500 Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Pixel Clock Frequency(MHz) RECALL 4 AUTO PIC 5 TV/AV 6 Displays present status and volume level. Select DYNAMIC, NORMAL, MILD, USER for PICTURE Select DSUB ANALOG, EXTERNAL VIDEO, S-VIDEO + / + + / + - / + - / - - / - Sync Polarity (H/V) 7 MUTE • It is a function of Mute control. When you push MUTE button, OSD display this image. This image can be toggle. OUT OF RANGE 1) The screen shows this when signal is out of range. 2) The screen shows this when there is no signal. 3) The screen shows this when the signal cable is not connected. NO SIGNAL CHECK CABLE OSD MESSAGE 8

and remove the safeguard tape. And then attach it exactly where you want. 2. Fasten the Monitor with Tapping Screw. 3. Adjust angle of Stand and install Monitor. 4. Connect each connecting cable as in the product installation reference. 6 8” TFT LCD DIGITAL COLOR MONITOR CONNECTIONS

SPECIFICATIONS ITEM LCD PANEL BRIGHTNESS CONTRAST RATIO VIEW ANGLE CR≥10 360 cd/m2 500:1 70/ 65/ 70 (H/U/D) SIZE NUMBER OF PIXELS DOT PITCH 20.32 cm (8.0inch) 800 x 600 0.2025(W) x 0.2025(H) mm SPECIFICATION INPUT SIGNAL VIDEO Composite Video, S-VIDEO (75 ohm 1Vp-p) ANALOG R.G.B 0.7Vp-p FRE- QUENCY 15.73 KHz 60 Hz HORIZONTAL VERTICAL USER CONTROLS POWER ON/OFF, MENU, MODE, PRO UP/DOWN DIMENSION (W x H x D) 223(W) x 178(H) x 34.5(D) mm -10℃ ~ 60℃ OPERATING TEMPERATURE STORAGE TEMPERATURE -20℃ ~ 70℃ 1.2 kg (Exclude Monitor Bracket) WEIGHT ※ Design and specifi cations could be changed without notices. MONO INPUT 400mVrms AUDIO POWER SUPPLY DC 12V 10 Watt AT DC 12V VOLTAGE CONSUMPTION NTSC/ PAL/ AUTO INPUT SYSTEM 7 Languages OSD DISPLAY TTL Separate, Composite INPUT SYNCHRONOUS SOUND SIGNAL 0.5 Watt max 7 8” TFT LCD DIGITAL COLOR MONITOR CHANGING REMOTE CONTROL BATTERY 1) Slide and open the battery cover. 2) Insert new battery and ensure that the polarities are correct when inserting. (No. CR2025) 3) Slide and close the battery cover.