Blizzard Lighting Puck Fab5 Manual
Read Online
Read the Blizzard Lighting Puck Fab5 Manual online using the built-in PDF viewer.
Text of the manual
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
TABLE OF CONTENTS
The Puck™ Fab5 LED PAR Can
1
1. Getting Started
3
What’s In The Box?
3
Getting It Out Of The Box
3
Powering Up!
3
Getting A Hold Of Us
3
Safety Instructions (Don’t Stick Your Hand In The Toaster!)
4
2. Meet The Puck™ Fab5 LED PAR Can
5
Features
5
DMX Quick Reference (3/5/12-Channel Modes)
5
The Puck™ Fab5 Pin-up Picture
7
3. Setup
8
Fuse Replacement
8
Connecting A Bunch Of Puck™ Fab5 LED PAR Cans
8
Data/DMX Cables
8
�
Using�this�fixture�with�the�wiCICLE®�Wireless�DMX�System�
8
4. Operating Adjustments
10
DMX Mode & DMX Mode Selection
10
Master/Slave Mode
10
Sound Active Mode
10
Custom Color Display
10
Fixture running hour display
11
Additional Operating Help
11
Troubleshooting
12
5. Appendix
13
A Quick DMX Lesson
13
Keeping The Puck™ Fab5 LED PAR Can As Good As New
14
Returns (Gasp!)
14
Shipping Issues
14
Tech Specs
15
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
�
•�1�x�Puck™�Fab5�Flat�LED�PAR�Fixture
�
•�1x�IEC�Power�Cord
�
•�This�Lovely�User�Manual
Getting It Out Of The Box
Congratulations on being completely and utterly qtastic! Now that
you’ve got The Puck™ Fab5 (or hopefully, Pucks!), you should carefully
unpack the box and check the contents to ensure that all parts are
present and in good condition. If anything looks as if it has been dam-
aged in transit, notify the shipper immediately and keep the packing
material for inspection. Again, please save the carton and all packing
materials.�If�a�fixture�must�be�returned�to�the�factory,�it�is�important�
that�the�fixture�be�returned�in�the�original�factory�box�and�packing.
Powering Up!
All�fixtures�must�be�powered�directly�off�a�switched�circuit�and�cannot
be run off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0% to
100% switch.
AC Voltage Switch -�Not�all�fixtures�have�a�voltage�select�switch,�so�
please�verify�that�the�fixture�you�receive�is�suitable�for�your�local�pow-
er�supply.��See�the�label�on�the�fixture�or�refer�to�the�fixture’s�specifi-
cations�chart�for�more�information.��A�fixture’s�listed�current�rating�is�
its�average�current�draw�under�normal�conditions.�Check�the�fixture�or�
device carefully to make sure that if a voltage selection switch exists
that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit
matches the line voltage applied. Damage to your fixture may
result if the line voltage applied does not match the voltage
indicated on the voltage selector switch. All fixtures must be
connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email.
We’ll be happy to help, honest.
Blizzard Lighting
W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA
[email protected]
www.blizzardlighting.com
1.866.493.6025
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
•��Please�keep�this�User�Guide�for�future�use.�If�you�sell�the�unit�to�someone�
else, be sure that they also receive this User Guide.
•��ALWAYS�make�sure�that�you�are�connecting�to�the�proper�voltage,�and�that�
the line voltage you are connecting to is not higher than that stated on the de-
cal�or�rear�panel�of�the�fixture.
•��This�product�is�intended�for�indoor�use�only.
•��To�prevent�risk�of�fire�or�shock,�do�not�expose�fixture�to�rain�or�moisture.�
•��Make�sure�there�are�no�flammable�materials�close�to�the�unit�while�operating.
•��The�unit�must�be�installed�in�a�location�with�adequate�ventilation,�at�least�
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
•��ALWAYS�disconnect�from�the�power�source�before�servicing�or�replacing�fuse�
and be sure to replace with same fuse size and type.
•��ALWAYS�secure�fixture�using�a�safety�chain.�NEVER�carry�the�fixture�by�its�
cord. Use its carrying handles.
•��DO�NOT�operate�at�ambient�temperatures�higher�than�104°F�(40°C).
•��In�the�event�of�a�serious�operating�problem,�stop�using�the�unit�immediately.�
NEVER�try�to�repair�the�unit�by�yourself.�Repairs�carried�out�by�unskilled�people�
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
•��NEVER�connect�the�device�to�a�dimmer�pack.
•��Make�sure�the�power�cord�is�never�crimped�or�damaged.
•��Never�disconnect�the�power�cord�by�pulling�or�tugging�on�the�cord.
•��Avoid�direct�eye�exposure�to�the�light�source�while�it�is�on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at sup-
[email protected].
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
DMX Quick Reference (12-Channel Mode)
Channel
What It Does
1
Dimmer
2
Strobe (0-15 off, 16-255 strobe slow <-> fast)
3
Red Intensity
4
Green Intensity
5
Blue Intensity
6
Amber Intensity
7
White Intensity
8
Color Snap
9
Snap Speed (0-15 off, 16-255 Snap Slow <--> Fast)
10
Color Fade
11
Fade Speed (0-15 off, 16-255 Snap Slow <--> Fast)
12
Sound Active (0-127 off, 128-255 Sound Active)
2. MEET ThE PUCk™ FAB5 FLAT LED PAR FIxTURE
MAIn FEATURES
• Light Source: 7* 15-watt, 5-in-1 RGBWA All-In-One LED’s
• Variable electronic strobe and dimmer
• Built-in automated programs via DMX and master/slave
• Built-in sound active programs
• Full RGBAW color mixing in standalone and master/slave
• Color Preset (3-Channel), RGBAW (5-Channel) and extended (12-Channel) DMX
• Able to directly power the wiCICLE® wireless system via DMX
ADDITIONAL FEATURES
• Lightweight and Compact (It kept its New Years’ resolution!)
• 4-Button LED control panel for easy programming
• Dual bracket for flexibility in mounting
• Power outlet for fixture linking (up to 50 fixtures)
• Running hours display
• Two-piece mounting yoke allows flexibility in positioning
Optical:
• Beam Angle: 25°, Field Angle: 29°
• Light Source: 7* 15-watt, 5-in-1 RGBWA All-In-One LED’s
• Flicker-free constant-current LED driver
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
DMX Quick Reference (3-Channel Mode)
Channel
What It Does
1
Dimmer (0-15 off, 16-255 Dim <--> Bright)
2
Strobe (0-15 off, 16-255 strobe slow <-> fast)
3
Color Select
Value
Red
Green
Blue
Amber
White
001-004
ON
005-008
ON
009-012
ON
013-016
ON
017-020
ON
021-024
ON
ON
025-028
ON
ON
029-031
ON
ON
032-035
ON
ON
036-039
ON
ON
040-043
ON
ON
044-047
ON
ON
048-051
ON
ON
052-055
ON
ON
056-059
ON
ON
060-062
ON
ON
ON
063-066
ON
ON
ON
067-070
ON
ON
ON
071-074
ON
ON
ON
075-078
ON
ON
ON
079-082
ON
ON
ON
083-086
ON
ON
ON
087-090
ON
ON
ON
091-093
ON
ON
ON
094-097
ON
ON
ON
098-101
ON
ON
ON
ON
102-105
ON
ON
ON
ON
106-109
ON
ON
ON
ON
110-113
ON
ON
ON
ON
114-117
ON
ON
ON
ON
118-120
ON
ON
ON
ON
ON
121-255 Chase (Slow <--> Fast)
DMX Quick Reference (5-Channel Mode)
Channel
What It Does
1
Red Intensity
2
Green Intensity
3
Blue Intensity
4
Amber Intensity
5
White Intensity
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
Figure 1: The Puck™ Fab5 Pin-Up Picture
Ridiculously
thin!
5-in-1 RGBWA-
Color LED’s
Figure 2: The Rear Connections
AC Power In/Out
DMX Out
DMX In
LED Control Panel
Microphone
Dual
Mounting Yokes
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
With�a�flat�head�screwdriver,�wedge�the�fuse�holder�out�of�its�
housing. Remove the damaged fuse from its holder and replace
with exact same type fuse. Insert the fuse holder back in its
place and reconnect power.
Connecting A Bunch of Puck™ Fab5 Flat LED PAR Cans
You will need a serial data link to run light shows using a DMX-
512�controller�or�to�run�shows�on�two�or�more�fixtures�set�to�
sync�in�master/slave�operating�mode.�The�combined�number�of�channels�required�by�all�the�fixtures�on�a�
serial�data�link�determines�the�number�of�fixtures�the�data�link�can�support.
Fixtures�on�a�serial�data�link�must�be�daisy�chained�in�one�single�line.�Also,�connecting�more�than�32�fix-
tures on one serial data link without the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640 ft). The maximum recommended
number�of�fixtures�on�a�serial�data�link�is�32�fixtures.
Data/DMX Cabling
To�link�fixtures�together�you’ll�need�data�cables.��You�should�use�data-grade�cables�that�can�carry�a�high�
quality signal and are less prone to electromagnetic interference.
For�instance,�Belden©�9841�meets�the�specifications�for�EIA�RS-485�applications.�Standard�microphone�
cables will “probably” be OK, but note that they cannot transmit DMX data as reliably over long distances.
In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
USInG THIS FIXTURE WITH THE wiCICLE® WIRELESS DMX SYSTEM
In�addition�to�the�unbridled�thrill�you�already�received�the�first�time�you�plugged�in�
your�fixture,�you’ll�be�delighted�to�know�that�This�fixture�also�works�seamlessly�with�our�
wiCICLE®�Wireless�DMX�system,�without�additional�power.
•�ONLY�fixtures�bearing�this�logo�are�certified�for�use�with�the�wiCICLE®�without�external�
power.
•�Unauthorized�modification�and/or�using�the�wiCICLE®�with�
unapproved�fixtures�may�cause�damage�to�the�wiCICLE®�or�
fixture.��UNDER�NO�CIRCUMSTANCES�IS�BLIZZARD�LIGHTING�
RESPONSIBLE FOR ANY DAMAGE FROM SUCH OPERATION.
•�Fixtures�bearing�the�above�logo�MUST�only�use�cable�and�connectors�which�separate�
chassis/case ground from cable shielding. Cabling with the shield connected to the connec-
tor’s�case/chassis�may�cause�malfunction�and�damage�to�the�wiCICLE®�or�fixture.
•�wiCICLE®�transmitters�have�additional�power�requirements�and�therefore�cannot�be�
powered�directly�from�the�fixture.��You�will�need�to�utilize�the�supplied�AC/DC�adaptor�to�
drive�wiCICLE®�transmitters�in�your�system.
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
Each wiCICLE® acts as both a transmitter and a receiver, depending on whether a DMX
source is applied to the integral XLR connector. This is an extremely powerful feature of
the system, however, it also requires 1 piece of due dilligence, and that is the removal of
extraneous DMX signals from your lighting rig BEFORE proceeding.
SO: BEFORE DOInG AnYTHInG ELSE, YOU SHOULD DISABLE AnY BUILT-In PRO-
GRAMS In THE FIXTURES YOU WISH TO COnnECT AnD/OR SET THEM AS SLAVES
PRIOR TO RETURNING THEM TO DMX MODE (IF APPLICABLE). Most fixtures
contain a built-in automatic, sound active or custom program which is designed
to operate with the fixture NOT connected to a DMX chain.
Some�of�these�programs�will�automatically�run�unless�the�fixture�is�set�to�slave�mode.��
These�fixtures�typically�sense�DMX�automatically�and�switch�to�DMX�mode�upon�receiving�
DMX signal (our Pucks do that!)
If you plug a wiCICLE®�“receiver”�into�an�autosensing�fixture�set�as�a�“master,�“chances�are�
good that the wiCICLE® “receiver” will begin transmitting the master program. Most times,
this is undesirable, and taking the two seconds to switch these programs off will solve a lot
of ails.
Got that done? Good! Then let’s proceed!
1. Plug the wiCICLE®�Receiver�into�the�“DMX�IN”�connector�of�the�fixture�and�verify�it�is�
receiving power (the STATUS LED should illuminate.)
2. Connect the AC/DC adaptor to the the wiCICLE® Transmitter and verify it is receiving
power (the STATUS LED should illuminate.)
3. Press the RECESSED SELECTOR BUTTOn on the Transmitter to select the operating
channel group. (The system will store this setting for future use)
The 7-Color Status LED will change color to indicate the current channel group:
4. Follow the same procedure on the Receiver to select the channel group.
5. Once both the transmitter and receiver(s) are both set to the same channel group,
connect�the�transmitter�to�the�DMX�controller�or�the�DMX�out�of�a�fixture�on�your�DMX�
chain.
6. Once a DMX signal is provided to the transmitter, the status LED will blink RED slowly
until communication is established with the receiver. The status LED on the receiver(s)
will�flash�GREEN slowly until communication is established.
7. Once the clearest channel is auto-selected, the status LEDs will blink quickly on both
the transmitter and receiver. NOTE: The color of the LED DURING operation does not
indicate channel group, instead it indicates whether the unit is transmitting or receiving.
That’s It!
WE hAD ThIS SPACE, SO WE FIGURED WE’D DRAW
YOU A PICTURE:
Antenna Housing & 1/2-wave Antenna
Antenna ferrule & articulation joint
Stainless Steel Housing
Recessed Selector Button
3-Pin XLR Connector
(Male on transmitter, Female on receiver model)
· GROUP 1: RED
· GROUP 2: GREEn
· GROUP 3: YELLOW
· GROUP 4: BLUE
· GROUP 5: VIOLET
· GROUP 6: CYAn
· GROUP 7: WHITE
Status LED
nOTE: “GROUP”
number also
corresponds to the
“GROUP” setting on
our LightCaster™
wireless DMX
Transceiver.
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
nOTE: After making any change, the unit will return to the correct mode in about 10 seconds.
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
1.)�The�default�mode�for�the�fixture�is�DMX,�which�appears�as�Addr on the LED
Readout. Use the button then the and buttons to
choose a channel between 1 and 512. Press �again�to�confirm.
2.) To change between 3 and 6 channel DMX mode, select ChNd, then press
. Select either 3Ch, 5Ch or 12Ch, then press again to
confirm.
Master/Slave Mode (Auto/Sound Active/Color Preset/Custom):
1.) Use standard DMX cables to daisy chain your units together via the DMX
connector on the rear of the units.
2.) Choose a unit to function as the Master. Select MAST. The master unit must be
the�first�unit.��Finally,�chain�the�units�together�using�DMX�cable.
Master
SLNd
then
NASt�
to�confirm.
3.) Select slave function by using the /�keys�to�reach�SLAV�in�the�
Master/Auto menu on the slave units, and they will react in the same as the Master.
Slave
SLNd
then
SLAu�
to�confirm.
nOTE: When a unit is set to slave and no master is connected, Stby will
appear on the LED display.
4.)�On�the�master�fixture,�use�the�/ keys to reach SHND, which
allows you to select the following:
Sound active SoUn then �to�confirm.
Auto mode
CoLo
then
Auto, then �to�confirm.
Color preset
CoLo
then
CoL 1 - CoL 31,
Color strobe
StCo
then
0-255 (Slowest <-.-> Fastest)
then CoL 1 - CoL 31,
To set a custom color in Master/Slave/Standalone Mode:
Using this function, you can select any color by adjusting the Red, Green, Blue, Amber and
White values from 0-255. You may also adjust the color balance of the fixture.
Please note that modifying the values in this step will affect ALL modes, therefore
we recommend resetting all levels to their highest value (255) after using this mode.
1.) Select NAnu from the control panel, then hit .
2.) Choose rEd, GrEE, bLuE, ANbE or Uhit, then hit to
confirm.
3.) Using the / keys, select the color you wish to display by
varying Red/Green/Blue intensity between 0 and 255, then hit �to�confirm�
each color choice.
4.) Select Color preset mode as instructed above, then select CoL 15. then
�to�confirm.
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
To Show the Fixture Running Hours:
1.) Select FhrS from the control panel, then hit �to�confirm.��
Menu Conventions
Addr
= “ADDR,” DMX Address Set/Adjust
ChNd
= “CHMD,” Channel Mode Adjust
3 /5 /12 Ch = “3 Ch,” 3/5/12-Channel DMX Mode
SLNd
= “SLMD,” Slave Mode Adjust
NASt = “MAST,” Master, set the unit to Master Mode.
SLAv =�“SLAV”�Slave,�set�the�unit�to�Slave�Mode.
StbY = “STBY,” Standby, unit is in Slave with no Master Fixture.
SHNd
Sou1 = “SOU1,” Sound Active 1, Scenes fade slowly when there is no audio.
Sou2 = “SOU2,” Sound Active 2, Independent slow fade of inner/outer LED’s.
Sou3 = “SOU3,” Sound Active 3, Scenes black out when there is no audio.
CoLo = “COLO,” Color Preset Mode.
Co XX = “CO 1 - CO31," Color Preset X.
AUto = “AUTO,” Auto (Color Snap) Mode.
FAdE = “FADE,” Color Fade Mode.
SP X = “SP 1 - SP 8,” Fade Speed 1-8 (Fast <-> Slow)
StCo = “STCO,” Color Strobe Mode.
Co XX = “CO 1 - CO31,” Color Preset X.
NANu = “MANU,” Manual Color / White Point Adjustment Mode.
REd = “RED," Adjust Red Intensity from 0 to 255.
GrEE = “GREE,” Adjust Green Intensity from 0 to 255.
bLuE = “BLUE,” Adjust Blue Intensity from 0 to 255.
ANbE = “AMBE,” Adjust Amber Intensity from 0 to 255.
UhIt = “WHIT,” Adjust White Intensity from 0 to 255.
FhrS = “FHRS,” Displays Fixture Running Hours
tESt = “TEST," Test Mode.
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
Quick Tips & Tricks:
Problem: The Puck LED readout says “StbY,” (Standby), no output.”
Solution: The�Puck�is�in�Slave�mode�with�no�master�fixture�connected.
Press
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
5. APPENDIx
A Quick Lesson On DMX
DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre
Technology (USITT) as a standardized method for connecting lighting consoles to lighting
dimmer�modules.�It�was�revised�in�1990�and�again�in�2000�to�allow�more�flexibility.��The�
Entertainment Services and Technology Association (ESTA) has since assumed control over
the DMX512 standard. It has also been approved and recognized for ANSI standard clas-
sification.��
DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common
communications standard used by lighting and related stage equipment.
DMX provides up to 512 control “channels” per data link. Each of these channels was origi-
nally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting
console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an
8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb
being completely off while 255 corresponds to the light bulb being fully on.
DMX data is transmitted at 250,000 bits per second using the RS-485 transmission stan-
dard over two wires. As with microphone cables, a grounded cable shield is used to prevent
interference with other signals.
There�are�five�pins�on�a�DMX�connector:�a�wire�for�ground�(cable�shield),�two�wires�for�
“Primary” communication which goes from a DMX source to a DMX receiver, and two wires
for a “Secondary” communication which goes from a DMX receiver back to a DMX source.
Generally,�the�“Secondary”�channel�is�not�used�so�data�flows�only�from�sources�to�receiv-
ers. Hence, most of us are most familiar with DMX-512 as being employer over typical
3-pin�“mic�cables,”�although�this�does�not�conform�to�the�defined�standard.
DMX�is�connected�using�a�daisy-chain�configuration�where�the�source�connects�to�the�input�
of�the�first�device,�the�output�of�the�first�device�connects�to�the�input�of�the�next�device,�
and so on. The standard allows for up to 32 devices on a single DMX link.
Each receiving device typically has a means for setting the “starting channel number” that
it�will�respond�to.�For�example,�if�two�6-channel�fixtures�are�used,�the�first�fixture�might�
be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next
fixture�would�be�set�to�start�at�channel�7�so�it�would�respond�to�channels�7�through�12.
The greatest strength of the DMX communications protocol is that it is very simple and
robust. It involves transmitting a reset condition (indicating the start of a new “packet”),
a start code, and up to 512 bytes of data. Data packets are transmitted continuously. As
soon�as�one�packet�is�finished,�another�can�begin�with�no�delay�if�desired�(usually�another�
follows within 1 ms). If nothing is changing (i.e. no lamp levels change) the same data will
be sent out over and over again. This is a great feature of DMX -- if for some reason the
data�is�not�interpreted�the�first�time�around,�it�will�be�re-sent�shortly.
Not�all�512�channels�need�to�be�output�per�packet,�and�in�fact,�it�is�very�uncommon�to�find�
all 512 used. The fewer channels are used, the higher the “refresh” rate. It is possible to
get DMX refreshes at around 1000 times per second if only 24 channels are being trans-
mitted. If all 512 channels are being transmitted, the refresh rate is around 44 times per
second.
In summary, since its design and evolution in the 1980’s DMX has become the standard
for�lighting�control.��It�is�flexible,�robust,�and�scalable,�and�its�ability�to�control�everything�
from dimmer packs to moving lights to foggers to lasers makes it an indispensible tool for
any lighting designer or lighting performer.
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
Keeping Your Puck™ Fab5 As Good As new
The�fixture�you’ve�received�is�a�rugged,�tough�piece�of�pro�lighting�equip-
ment, and as long as you take care of it, it will take care of you. That said, like
anything, you’ll need to take care of it if you want it to operate as designed.
You�should�absolutely�keep�the�fixture�clean,�especially�if�you�are�using�it�in�an�
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled
drinks.
Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the�fixture�running�cool�and�prevent�damage�from�overheating.��
In�transit,�keep�the�fixtures�in�cases.��You�wouldn’t�throw�a�prized�guitar,�
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
fixtures.��
Common�sense�and�taking�care�of�your�fixtures�will�be�the�single�biggest�thing�
you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your cli-
ent’s satistfaction and “wow factor.” That’s what it’s all about, after all!
Returns (Gasp!)
We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But, like
any complex piece of equipment designed and built by humans, once in a while,
something�doesn’t�go�as�planned.��If�you�find�yourself�with�a�fixture�that�isn’t�
behaving�like�a�good�little�fixture�should,�you’ll�need�to�obtain�a�Return�Authori-
zation (RA).
Don’t worry, this is easy. Just send an email to [email protected],
and we’ll issue you an RA. Then, you’ll need to send the unit to us using a
trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make�sure�you�carefully�pack�the�fixture�for�transit,�and�whenever�possible,�use�
the original box & packing for shipping.
When�returning�your�fixture�for�service,�be�sure�to�include�the�following:
1.) Your contact information (Name, Address, Phone Number, Email address).
2.) The RA# issued to you
3.) A brief description of the problem/symptoms.
We�will,�at�our�discretion,�repair�or�replace�the�fixture.��Please�remember�that�
any shipping damage which occurs in transit to us is the customer’s responsibil-
ity, so pack it well!
Shipping Issues
Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.
Claims must be made within seven (7) days of receipt.
The Puck™ Fab5 User Manual Rev. A
Copyright (c) 2012 Blizzard Lighting, LLC
Tech Specs!
Weight & Dimensions
Length
8.25 inches (210 mm)
Width
3.875 inches (98.43 mm)
Height
8.5 inches (215.9 mm)
Weight
4.2 lbs (1.92 kg)
Power
Operating�Volt-
age
Auto-ranging�100�V�~�240�V�50/60�Hz
Fuse
5A
Power & Current
0.71A,�55W�@�120VAC
Power Factor
.62
Light Source
LED
7* 15-watt, 5-in-1 RGBWA All-In-One LED’s
Optical
Beam Angle
25 degrees
29�degree�field
Luminous Inten-
sity
Lux /
Meter
RGBAW
Red
Green
Blue
Amber
White
1M
12,420
1,850
2,470
2,860
1,580
4,380
2M
3,520
500
660
830
480
1,270
Thermal
Max. Operating
Temp.
104 degrees F (40 degrees C) ambient
Control
Protocol
USITT DMX-512
DMX Channels
3/5/12 (User Selectable)
Input
3-pin XLR Male
Output
3-pin XLR Female
Other Operating
Modes
Standalone, Master/Slave, Sound Active, Color Preset,
Standalone Color Mixing
Other Information
There’s 5 syllables in the word “monosyllabic”.
Warranty
2-year limited warranty, does not cover malfunction
caused by damage to LED’s.
