Broseley Desire Installation & Operating Instructions Manual

Page 1 Installation & Operating Instructions Desire, Ignite & Hereford Inset Electric Stoves 2kw Output Fan Heater PLEASE NOTE THAT THIS APPLIANCE USES A MOTOR TO OPERATE THE FLAME EFFECT AND THAT IT MAY BE POSSIBLE TO HEAR IT WHERE THE BACKGROUND NOISE IS VERY LOW. THIS IS NORMAL AND SHOULD NOT BE A CAUSE OF CONCERN. These instructions should be read carefully and retained for future reference

Page 2 Important Safety Information  This heater must not be located immediately below a fixed socket outlet.  Do not use the heater in the immediate surrounds of a bath, a shower, or a swimming pool.  Do not cover this heater, or obstruct the air inlet or outlet, otherwise there is a risk of overheating.  The heater must be cooled down completely before any maintenance  This heater must be fixed against a vertical surface.  Under no circumstances should the heater be used as a free standing appliance.  After unpacking, please make sure that the appliance is intact, with no signs of damage caused by transport. If in doubt, do not use the appliance and contact the Service Centre.  During normal operation this appliance will emit noise from the internal fan unit.  If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.  Children should be supervised to ensure that they do not play with the appliance or handset  Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.  This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision  Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are in the vicinity.  Do not use this appliance as a primary heat source  Ensure that furniture, curtains and other combustible materials are positioned no closer that 1m from the front of the fire.  Do not stand the fire on the carpet – stand on a firm surface, which projects 250 mm (10 inches) beyond the front of the heater enclosure and is free of dust and lint.  If this fire is supplied through an extension cable, please ensure that it is the only appliance plugged into the extension and that the instructions for the extension cable / reel are followed.  CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.  This appliance must be positioned so that the plug / fused spur is accessible  In the event of a fault please disconnect the fire from the mains supply  Warning: This appliance must be earthed. The wires in the mains lead connected to this appliance are coloured in accordance with the following code: GREEN and YELLOW Earth BLUE Neutral BROWN Live As the colour of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with letter L or coloured Red.

Page 3 Assembly Please unpack carefully ensuring that any loose parts and all packing items are removed. Read any warning labels carefully (see Maintenance Section). Place waste packaging back into box and dispose of RESPONSIBLY. The appliance must be positioned so that plug (fused spur) is accessible. Only when you are certain that you have completed the following installation instructions should you plug in and switch on at the wall socket. Contents: 1 x Stove Body Trim, 1 off Fire engine (attached to stove body), Instruction leaflet, 4 off No.6 x 1 ¾” screws, Door (Packed in box) Preparation for Use Check that the supply voltage details on your flame effect fire are in accordance with your electrical supply. Your fire is fitted with a plug incorporating a 13 Amp fuse. In the event of replacing the fuse in the plug supplied, a 13 Amp fuse approved by ASTA to BS 1362 must be used. Before switching on, please read the following operation instructions. Installation  Ensure that the inset dimensions match the dimensions in Fig.1  Unpack the fire by removing all the boxes from the pallet and unscrewing the fire engine from the pallet, remove the L shaped bracket from the bottom rear of the stove “wings”.  Measure the thickness of the panel that the fire is to be fixed to for panels 18mm – 22mm leave the L bracket attached to the fixing wings, for panels 38mm - 42mm remove the vertical L - bracket on the fire fixing wings.  Remove the stove main body from the fire engine by loosening the 4 screws.  Slide the left hand fixing wing behind the panel, slide the fire all the way to the left, push the right hand side bracket behind the panel and centralise the fire into the opening.  Offer the Stove body trim up to the fire in the opening, using the 4 off 1 ¾ No.6 screws provided, loosely fix the trim to the holes provided on the fixing wings, once all four screws are loosely attached then fully screw the fire into position, take care not to overtighten and strip the threads of the hole.  Once the stove is in position only then turn on the mains supply and proceed to the door fitting section. Fig.1

Page 4 Assembly Door Fitting. Desire / Ignite Version:  The Door assembly supplied should be ready to fit, once the fire is installed then hang the Door onto the hinges fixed on the main body by locating the hinges on the door over the top of the hinges on the main body, move the door open and closed a few times so that the hinge mates correctly. Hereford Version:  The door should be supplied assembled with the upper hinge pin in position and the lower hinge pin ready to fit to the assembly. Locate the upper hinge pin in position in the upper hinge on the main body. Manoeuvre the door so that the lower pin (supplied) can drop through into the lower hinge pin. Lock the lower pin in position by fixing the slider component in position using the M5 Allen bolt. The slider should rest on top of the pin so as to prevent the pin rising up out of the lower hinge.

Page 5 Controls & Operation Thermostat: This model is fitted with a thermostat that is mounted on the right hand side of the stove unit. It can be used to control the heat output to maintain a constant room temperature to suit user requirements. This will ensure that excessive heat is not produced unnecessarily. To set the temperature: The knob is marked with numbers to indicate the maximum and minimum temperature positions. Start with setting 9 and when the room has reached a desired level turn the knob slowly to the left until the thermostat ‘clicks’ off. The thermostat will then maintain the room temperature at the selected level. To increase the temperature turn knob back to the right to a higher setting. Note: It is possible that if the room temperature is higher than the thermostat setting it will not come into operation and the heater will remain off until the temperature of the room cools. Manual Version: The Flame effect and heat controls are located behind the door  The first switch marked with a light bulb controls the lamp and flame effect  The next two switches operate the fan convector heater. To use the heater the middle of the three switches marked O / I (O is off, I is on) should be operated first for 1 kW of heat. The right hand switch also marked O / I should be used together with the middle switch to give 2kW of heat.  Note’ lamp’ switch must be in the ‘on’ position for heater to function. Remote Handset Version: Note: To use both remote and manual functions the Main (I / O) switch must be in the ‘on’ position.  The button marked Power turns all operations on / off.  The second button (marked Flame) turns the flame effect fan and lamps on / off.  The third button (marked Low) turns the heater fan and low heat setting on / off.  The last button (marked High) turns the heater fan and high heat setting on / off. POWER (ON / OFF) Press once turns appliance on (Neon illuminated) Press again turns appliance off. FLAME Press once turns Flame Effect on (neons illuminated) Press again turns Flame Effect off. LOW Press once turns Fan+Low heat on (neons illuminated) Press again turns Fan / Heat off HIGH Press once turns Fan+High heat on (neons illuminated) Press again turns Fan / Heat off (neons illuminated ) The indicator neons on the rear screen show as soon as the remote buttons / switches are operated. The neons turn off automatically 10 seconds after the settings have been changed.

Page 6 Maintenance Safety Thermal Cut-out and Thermal Link This appliance is fitted with an Electric Safety Control (E.S.). This is a safety device,which switches off the fire, if for any reason the appliance overheats. The E.S. Control can only be re-set after the appliance has cooled down, in order to re-set the E.S. Control, proceed as follows:  Switch off the appliance. Unplug at wall socket and leave for approximately 5-10 minutes.  Clean the filter unit as described in the care section of this instruction.  Plug in, switch on appliance and the E.S. Control will re-set. Ensure that the appliance is functioning correctly. If the E.S. Control switches off again it is advisable to have the appliance checked by a competent electrician. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility. WARNING: - Before undertaking any maintenance or cleaning, ensure appliance is disconnected from mains supply. Only competent persons should service / repair appliance. Bulb Changing Open the door and remove the decorative coal effect by gently lifting it up and then rotating it at an angle to allow it to pass through the door opening. If present remove the cable tie which is securing the bulb in place. Unscrew and replace the damaged bulb(s) holding the body of the lamp holder if necessary to prevent rotation. Replace the fuel effect by gently sliding the fuel effect back into the recess. The Bulbs required are 11W E14 SES Mini Spiral available through all good DIY and electrical stockists. General Suite Care – not glass To maintain the appearance of your new suite we recommend that it is dusted using a lint free cloth. NEVER use any form of abrasives or a DAMP cloth on the stove or the surround. The area around the fire should be kept free of any materials such as lint or house dust (i.e. animal hair / carpet fibres) that could be drawn into the internal workings of the appliance and hence affect the performance. We recommend that you clean around the fan grille housing at regular intervals. This can be done using standard vacuum cleaner and suitable attachment. Glass A clean, dry synthetic cloth is normally all that is required to clean the glass. We do not recommend using any chemical cleaning fluids, sprays or foam as this may damage the paint finish of the product. Perspex To prevent scratching of the flame effect unit screen, we recommend only using a clean, dry synthetic cloth to clean the screen. Steel Sections A soft brush is normally sufficient to remove everyday dust and general debris from the surfaces of the stove. DO NOT use any kind of chemical or abrasive cleaning products on your stove as this will damage the paint finish. Electric Supply Cable Should the electric supply cable get damaged in any way, you will need to have it replaced by a qualified electrician.

Page 7 Guarantee Broseley Fires Ltd (the ‘Company’) provide a twelve month guarantee in respect of electric fire (the ‘Product’) ranges. 1. The twelve month Guarantee applies to:  All ‘Products’ in the ranges manufactured by the ‘Company’ (but subject to exceptions below); where  The ‘Product’ has been purchased and installed within the UK and in respect of  The initial installation; and in favour of  The original Purchaser 2. Proof of purchase must be retained by the Purchaser 3. The twelve month Guarantee does not apply to:  Damage or inferior workmanship practices while the ‘Product’ is being installed  Damage caused by the mis-use of the ‘Product’ or where normal standards of care and use have not been complied with.  Damage through a malfunction or an inadequately installed electric fire.  Damage or defects due to, mis-use, accident or unauthorised alterations. During the twelve month after the ‘Product’ has been supplied, the Guarantee covers the making good (whether by repair or replacement at the company’s option) of defects arising from defective manufacture of materials of ‘Product’ covered in paragraph (1), all at no cost to the Purchaser. This Guarantee does not affect your statutory rights On requiring service contact the retailer who supplied your product who will assist you and advise you as necessary. This fire complies with the European Safety Standards (LVD) EN60335-1, EN60335-2-30, the European Electro Magnetic Compatibility (EMC) EN55014, EN61000 and EN62233 which covers the essential requirements of the EEC Directives and 89/336 Broseley Fires Ltd. First Floor Unit B, Knights Court, Archers Way, Battlefield Enterprise Park, Shrewsbury SY1 3GA Tel: 01743 461444 Fax: 01743 461446 Email:[email protected] Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.