Corinex AnyWire Connectivity AV200 Quick Start Manual
Text of the manual
Corinex AV200 Powerline Ethernet Wall Mount
This document, as well as the software described in it, is furnished under license and may be used or
copied only in accordance with the terms of the license. The content of this document is furnished for
informational use only, it is subject to change without notice, and it does not represent a commitment
on the part of Corinex Communications Corp.
Corinex Communications Corp. assumes no responsibility or liability for any errors or inaccuracies that
may appear in this document.
It is our policy to enhance our products as new technologies, hardware components, software and
firmware become available; therefore, the information contained in this document is subject to change
without notice.
Some features, functions, and operations described in this document may not be included and sold in
certain countries due to government regulations or marketing policies.
The use of the product or its features described in this document may be restricted or regulated by law
in some countries. If you are unsure which restrictions or regulations apply, you should consult your
regional Corinex office or the authorized reseller.
Published by:
Corinex Communications Corp.
# 670 - 789 West Pender Street
Vancouver, B.C.
V6C 1H2 CANADA
Tel: +1 - 604 - 692 0520
Fax: +1 - 604 - 6940061
Corinex is a registered trademark of Corinex Communications Corp.
Apple, MAC OS X are either registered trademarks or trademarks of Apple Computer, Inc. in the U.S.A.
and/or other countries.
Microsoft, MS-DOS, MS, Windows are either registered trademarks or trademarks of Microsoft
Corporation in the U.S.A. and/or other countries.
All products or company names mentioned herein may be the trademarks of their respective owners.
Copyright (c) 2001-2006 by Corinex Communications Corp.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
information technology equipment. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference, the end user is advised to take adequate measures.
2006-04-28 ver.2.0
Quick Start Guide
2
Corinex AV200 Powerline Ethernet Wall Mount
Quick Start Guide
Thank you for choosing the Corinex AV200 Powerline Ethernet Wall Mount.
Please follow the steps below, to set up your adapter and the initial configuration.
1.
Plug the Wall Mount directly into a wall outlet, not a power strip. It will power up
automatically.
2.
Connect the computer to the adapter, using a straight-forward Ethernet cable which came
with the product.
3.
Change
the
IP
address
of
your
computer
to
10.10.1.1,
and
the
network
mask to 255.255.0.0. For more information on how to set the IP address on your system,
please see the User Guide, which can be found on the enclosed CD.
4.
Open a web browser (eg. Internet Explorer) and type the following address : http://10.10.1.69.
5.
This will open the configuration pages for your Corinex AV200 Powerline Ethernet
Wall Mount.
Quick Start Guide
3
Corinex AV200 Powerline Ethernet Wall Mount
On the authentication screen, enter “paterna” in the password field and click OK.
Quick Start Guide
4
Corinex AV200 Powerline Ethernet Wall Mount
Please click on Advanced Settings in the main menu. On the next page, click on Network
Settings in the submenu.
6.
You should now see the main page of the configuration interface.
Quick Start Guide
5
Corinex AV200 Powerline Ethernet Wall Mount
Note : Please make sure that each adapter in your network has a unique IP address.
8.
After entering a new IP Address, click OK. Please wait until the configuration page reloads.
9.
Navigate to the Tools section in the submenu. Click on Hardware Reset.
7.
In the Network Settings section of the configuration page, change the IP address of your
Corinex AV200 Powerline Ethernet Wall Mount.