Afinia H800+ Quick Start Manual
Read Online
Read the Afinia H800+ Quick Start Manual online using the built-in PDF viewer.
Text of the manual
Install Print Board
Install Software
Setup Printer
Setup Wi-Fi
Connect Printer Through Wi-Fi
Load and Print 3D Model
Index
1/2
3
4
5
6
7
8
Accessory Pack Contents
Verify the following items are in the H800+ packaging.
1. Filament
2. USB Cable
3. Power Cord
4. Power Supply
5. Putty Knife
6. FR-4 (Cell Perf) Boards (Four (4) total)
Two (2) Flex Boards with BuildTak surface
Two (2) Cell Perf Boards without BuildTak
7. Snipping Pliers
8. Nozzle Wrench
9. Spare Nozzle
10. Hex Wrenches
10
1
2
3
4
5
6
7
8
9
1. Remove foams from the H800+.
Cut and remove the nylon ties (yellow labelled).
There is no need to lift the platform to remove the bottom foams.
90°
Note: Lay down the foam at the bottom, then turn it 90 degrees to remove.
Install Print Board
Locked
Unlocked
guiding tube.
Warning: Do not touch the
platform while it is hot to
avoid burns.
3
¥
AFINIA
Position the perf board on the build platform, and make sure that all
the flat head screws on the heating plate are inside the holes of the
perf board.
Press the perf board and the heating plate together at the lower left
and the lower right corners, then slide the perf board towards the back
of the unit to lock it onto the heating plate.
Make sure all holes are locked properly
to ensure the perf board is flat.
Install the filament spool and insert the filament into the filament
Download and install the latest Studio software from the support section
of the Afinia website at www.afinia.com/support/downloads/. For the iPad or
Install Software
At the main menu “Build”
2
1
Connect power
the Studio software. Click “Build” in the main screen, then “Initailize” .
iPhone app, please visit the Apple app store in your iOS device and search for
2
4
¥
“Afinia 3D”.
to the H800+ and turn on the power switch, then connect
1
the USB cable
to the printer and the computer. Initialize the H800+ by using
the printer will beep two times and start to
Next, go to the Maintenance
Section, and click
“Extrude”.
In the “Build” menu, click “Calibrate”
the auto leveling function. This process will take a minute to complete.
Setup Printer
5
¥
, then “Auto Level” to initiate
When reaching printing temperature,
extrude. Now gently push the filament into
the small hole in the top of the printhead
until extrusion occurs at the nozzle.
When the extrusion completes, remove the
thin line of extruded filament and discard.
Go to “Printer” tab, select connected printer and click the stacked lines
and enter the password for the Wi-Fi network.
Open the “Settings” menu .
Your_Network
Your_Network
6
¥
button to see printer details. Choose Network to connect to a Wi-Fi network
Connect Printer Through Wi-Fi
Disconnect the USB cable.
Language
Printer
JSZ_BOX+_01
7
¥
In the “Printer” section, all the printers in the network will be displayed.
Click the H800+ you want to connect. If connected successfully, the
printer will have a check mark displayed.
2. Use the wheel to
adjust the model’s size,
location, and rotation.
(see full manual details)
4.
5.
3. Click “Print”.
Load and Print 3D Model
Build
8
¥
Click the “+” button, and choose an .STL or .UP3 file to load into the program.
The progress of slicing and data processing is shown on the status bar.
After data transfer is finished, the amount
of material to be used and estimated print time
will be shown.
8150 Mallory Court, PO BOX 846
Chanhassen, MN 55317
Phone Support: 952-279-2643
¥
youtube.com/afinia3dprint
Support: [email protected] Web: www.afinia.com
