Raymarine ST70 Operating Manual

Congratulations on having chosen Raymarine ST70+. ST70+ Instruments and Pilot Controllers give you easy access to the important information you need and fingertip control over your Raymarine autopilot, to make your boating experience both safe and enjoyable. Contents This Operating Guide This Operating Guide describes how to use ST70+ Instruments and Pilot Controllers on a day-to-day basis. If you need more comprehensive information, refer to the ST70+ User Reference Manual. General Getting started ......................................................................................................Card 1 Display grouping & control .................................................................................Card 2 Setting display brightness...................................................................................Card 3 Setting the correct local time ..............................................................................Card 4 Setting the screen colors.....................................................................................Card 5 Choosing the data units.......................................................................................Card 6 Data list................................................................................................................Card 21 Pilot Controller Setting up a Pilot Controller display...................................................................Card 7 Basic autopilot operation ....................................................................................Card 8 Using AutoTack ....................................................................................................Card 9 Using autopilot Track mode ..............................................................................Card 10 Using autopilot Wind Vane mode......................................................................Card 11 Using autopilot fishing patterns........................................................................Card 12 Instrument Switching instrument pages on & off ...............................................................Card 13 Setting instrument page rollover ......................................................................Card 14 Changing information on a page.......................................................................Card 15 Changing the page layout..................................................................................Card 16 Using alarm clock...............................................................................................Card 18 Using race timers ...............................................................................................Card 18 Setting alarms.....................................................................................................Card 19 Alarm events .......................................................................................................Card 20 ST70+ Operating Guide Raymarine UK Ltd, Anchorage Park, Portsmouth, Hampshire PO3 5TD, United Kingdom Tel: +44 (0) 23 9269 3611, Fax:+44 (0) 23 9269 4642 Raymarine Inc,21 Manchester Street, Merrimack, New Hampshire 03054, USA Tel: +1 603.881.5200, Fax: +1 603.864.4756 Part Number: 81309-1 Date: January 2009 www.raymarine.com

easily find the information you want: Important information Important Before using your ST70+ products, ensure they have been prepared for use in accordance with the Commissioning Procedures. Refer to the ST70+ User Reference Guide or the ST70+ installation Guide. EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Raymarine equipment and accessories assures compliance with the appropriate Electromagnetic Compatibility (EMC) regulations, but correct installation is required to ensure that performance is not compromised. Product documents The information in this guide is valid for ST70+ products and systems which have been installed and commissioned in accordance with the correct Raymarine procedures. Relevant documents are: • ST70+ User Reference Manual (contains commissioning, maintenance & troubleshooting procedures). • ST70+ Installation Guide (includes commissioning procedures). • SeaTalkng Reference Manual. Technical accuracy To the best of our knowledge, the information in this document was correct at the time it was produced. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. As a result, Raymarine cannot accept liability for any differences between the product and this document. Waste Electrical and Electronic (WEEE) Directive The WEEE Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some of Raymarine's products, we support its policy and ask you to be aware of how to dispose of this product. The crossed out wheelie bin symbol (illustrated here) found on our products signifies that this product should not be disposed of in general waste or landfill. Please contact your local dealer, national distributor or Raymarine Technical Services for information on product disposal. • Cards with information applicable to both Pilot Controller and Instrument are white. • Cards describing Pilot Controller and autopilot functions are colored • Cards describing Instrument functions are colored • WARNING: Product installation & operation This equipment must be installed and operated in accordance with the Raymarine instructions provided. Failure to do so could result in personal injury, damage to your boat and/or poor product performance. WARNING: Ensure safe navigation This product is intended only as an aid to navigation and must never be used in preference to sound navigational judgment. Only official government charts and notices to mariners contain all the current information needed for safe navigation, and the captain is responsible for their prudent use. It is the user’s responsibility to use official government charts, notices to mariners, caution and proper navigational skill when operating this or any other Raymarine product. WARNING: Ensure Commissioning Procedures have been completed If the ST70+ Commissioning procedures have not been completed, your displays could be displaying misleading information. Before using ST70+, ensure that the Commissioning Procedures in the ST70+ Installation Guide (also provided in the User Reference Manual) have been successfully carried out. www.raymarine.com

Each ST70+ display is set up as an Instrument or a Pilot Controller during commissioning, and is controlled from an external keypad. Instrument and Pilot Controller keypad types are fitted as appropriate. Note that the type of Pilot Controller keypad fitted depends on boat type (power or sail boat). Switching on To switch on an ST70+ display or display group, or to re-apply power to individual displays in a working group that have been switched off, press and release , on an associated key- pad. All displays in the relevant group then power up. At power up, each display shows the page that was in use when the power was last switched off, once the system has been commissioned. WARNING: Do not use a display until the appropriate commissioning procedure has been successfully carried out (as in the ST70+ Installation Guide or the ST70+ User Reference Manual). If a Language page is displayed when you switch on, the display has not been commissioned, so you need to carry out the commis- sioning procedure before using the display. Switching off Important: In the ‘Switched Off’ condition, power is still supplied to the displays. If you want to remove power completely, switch it off at the relevant distribution panel. To switch off a display, hold down on an associated keypad. A countdown starts and a popup shows the progress and indicates which displays you are switching off (default is Group). Con- tinue holding down until the countdown completes and the selected displays power down. If you want to change which units are being switched off: 1. During the countdown, release to pause the countdown, then use either the Rotary Con- trol or -1 and +1 on the associated keypad to select either: • Group - to switch off all the displays in this group (default setting), or • Display - to switch off just this display. 2. Hold down again until the countdown completes and the selected displays power down. Applicability: The procedures on this card apply to ST70+ Instruments and Pilot Controllers. Display Instrument keypad Pilot Controller keypad (power) Pilot Controller keypad (sail) Typical Instrument page Typical Pilot Controller page D11015-1 D11016-1 Language English (UK) Press OK to select ST70+ general information Getting started

Selecting & confirming options & values Many ST70+ setup functions, display options and values are set up by using the keyboard to scroll to the required option or value, then confirming, by pressing OK. The manner in which you do this depends on keypad type. Scrolling. To scroll to an option or set a value, either: • Press the < and > buttons on the sail boat Pilot Controller keypad, or • Turn the Rotary Control on the power boat Pilot Controller keypad or the Instrument keypad. OK function To OK selections and edited values, either: • Press the OK button, on the sail boat Pilot Controller keypad, or • Press the center of the Rotary Control inwards, on the power boat Pilot Controller keypad or the Instrument keypad. ST70+ Instruments On an ST70+ Instrument display: • Data is displayed on operational pages. Up to eight pages are available. • Each page can be divided into up to six separate data areas or ‘frames’. To move from page to page, use PAGE UP or PAGE DN on the associated keypad. You can also apply a rollover (see Card 14) to change pages automatically Customizing pages You can change any operational page, to show only the information you want. You can: • Change the information in any frame of any page. Refer to Card 15. • Rebuild any page, so it has a different frame layout with different data. Refer to Card 16. ST70+ Pilot Controllers On an ST70+ Pilot Controller display, you can choose one of three different page types to view navigational information. To move from one Pilot Controller page type to another, hold down MENU for 1 second. Refer to Card 7 for a description of the data on the different Pilot Controller page types. or Scrolling = OK functions Depth ft 9.0 Lat N Speed kts 7.0 Heading xx 63 Time 24H 11:23 o 47 o Lon 47 Page 1 D11018-1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 GILKICKER POINT GILKICKER POINT Standby Plain view Compass Rose view Isometric view ST70+ general information Getting started

instructions describe how to set up groups and allocate keypads. Refer to the ST70+ User Reference Manual or the ST70+ Installation Guide. Group parameters Each group: • Can contain up to four displays of the same type i.e. EITHER Instrument OR Pilot Con- troller. You cannot mix Instruments and Pilot Controllers in the same group. • Can be controlled by one or more keypads of the appropriate type. Selecting displays In any display group, you can control one display at a time. To select the display you want to control, use the (Select Display) button on any keypad in the group. The ‘selected’ display screen is highlighted. Each time you press the Select Display button, the next display in the group is selected. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments and Pilot Controllers. D11020-1 Selected display Depth FT Lat N Speed KTS Heading MAG 63 Time 24H 11:23 o o o 47 o Lon 67 6.0 7.0 Time 24H 11:23 Heading MAG 63 o Lat N o 47 o Lon 67 Depth FT 6.0 Speed KTS 7.0 Time 24H 11:23 Heading MAG 63 o Lat N o 47 o Lon 67 Depth FT 6.0 Speed KTS 7.0 Time 24H 11:23 Heading MAG 63 o Lat N o 47 o Lon 67 Depth FT 6.0 Speed KTS 7.0 ST70+ general information Display grouping & control

Pilot Controller). You can set the brightness on either just one display, all the displays in a group, or all displays in a system. The group setting is the default. Procedure 1. Starting With any operational page displayed, press MENU to display the Main Menu then scroll to the Display Settings option. Press OK to show the Display Settings menu. 2. Select option At the Display Settings page, scroll to the Brightness option. Press OK to display the 1. Brightness - select zone setup box. 3. Select displays Scroll to select the displays on which you want to adjust the screen brightness. The options are: • This group - affects all displays in the same group as the selected display (default setting). • All displays - affects all displays in the system. • This display - affects just this display. Press OK to display the 2. Brightness - select value screen 4. Set brightness level Scroll to set the screen brightness. Press OK to save the setting and return to the Display Settings menu. Returning to operating page To return to normal operation from the Display Settings menu, press CANCEL twice. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments and Pilot Controllers. i D11021-1 Press OK to continue 1. Brightness - select zone This group iSelect the zone for brightness changes, using < & >. i D11022-1 Press OK to accept 2. Brightness - select value Adjust brightness using < & >. 50 % ST70+ general information Setting display brightness

local time as your system time. Note: If you want to change the time or date format, use the procedure in the ST70+ User Reference Manual. Setting the time Note: If your ST70+ display is connected to a Raymarine multifunction display, then the time offset is controlled by the mul- tifunction display so you cannot use this procedure to change it. 1. Starting With any operational page displayed, press MENU, to display the Main Menu, then scroll to the Display Settings option. Press OK to show the Display Settings menu. 2. See current settings At the Display Settings page, scroll to the Time & Date option. Press OK to display the Time & date summary page. • To return to the Display Settings menu without chang- ing any values, press CANCEL. • To set up the local time, press OK, to select the Time & Date menu. 3. Select time offset With the Time & Date menu displayed, scroll to Set time offset. Press OK to display the Set time offset setup page. The time offset is the difference in time between GMT (time at Longitude 0°) and local time. 1. Scroll to set the appropriate time offset for your area. 2. Press OK to accept the value and display the Time & Date summary page. Returning to operating page To return to normal operation from the Time & Date summary page displayed, press CANCEL three times. Applicability: The procedures on this card apply to ST70+ Instruments and to ST70+ Pilot Controllers, connected to SeaTalk and SeaTalkng pilot types. Date and time information are available only if your ST70+ display is receiving GPS data. i D11028-1 Press OK to continue Time & Date These are your current settings. Time 11:01:03 Date 14/06/07 Time Offset -1 Hrs Time Format 24-hour Date Format dd/mm/yy 100 D11029-1 Time & Date Set time offset Press OK to select i D11105-1 Press OK to accept Set time offset -1 Use < & > to adjust. CANCEL exits without saving. Hrs ST70+ general information Setting the correct local time

There are four different color settings plus an inverse video option. Choosing colors 1. Starting With any operational page displayed, press MENU, to display the Main Menu, then scroll to the Display Settings option. Press OK to show the Display Settings menu. 2. Select option At the Display Settings page, scroll to the Colors option. Press OK to display the 1. Colors - select zone screen. 3. Select displays Scroll to select the displays on which you want to set the screen colors: • This group - affects all displays in the same group as the selected display (default setting). • All displays - affects all displays in the system. • This display - affects just this display. Press OK to display the 2. Colors - select value screen. 4. Select color Scroll to select the screen colors you want. You can choose from. • Mode 1 • Mode 2 • Mode 3 • Red/black (recommended for night time viewing) • Inverse Press OK to save the setting and return to the Display Settings menu. Returning to operating page To return to normal operation from the Display Settings menu, press CANCEL twice. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments and Pilot Controllers. i D11023-1 Press OK to continue 1. Colors - select zone Select the zone for color changes, using < & >. This group i i D11024-1 Press OK to accept 1. Colors - select value Select colors using < & >. Mode 1 ST70+ general information Setting the screen colors

range of imperial and metric units. Data unit settings are applied to the whole system. Procedure 1. Starting With any operational page displayed, press MENU, to display the Main Menu, then scroll to the Display Settings option. Press OK to show the Display Settings menu. At the Display Settings menu, scroll to the Units option. Press OK to display the first Units summary page. 2. Select option Press OK again to display the second Units summary page. Press OK to display the Select units menu. 3. Select units. Scroll to the unit you want to change. Press OK to display the selection screen for the units you have chosen. 4. Set units Scroll to select the units you want, then.Press OK to save the setting and return to the first Units summary page. If you want to set up other units, repeat the Select option and Select units procedures above. Returning to normal operation When you have finished setting the units and the Select units menu is displayed: 1. Scroll to the Continue option. 2. Press OK to return to your operational page. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments and Pilot Controllers. i D11025-1 Press OK to continue Units summary These are your current settings. Speed KTS Distance NM Depth FT Wind Speed KTS Heading M Flow Rate G/H Temperature °C i D11026-1 Select units Wind Speed Units Select units to change, using < or >. Press OK to select i D11106-1 Press OK to accept Wind Speed Units KTS Select required units, using < or >. CANCEL exits without saving. i D11027-1 Select Units Continue Select units to change, using < or >. Press OK to select ST70+ general information Choosing the data units

• The type of pilot page you want. • The data you want to see in the on-screen data boxes. To scroll to any menu selection, use either the Rotary Control or the < & > buttons, as appro- priate for the keypad you are using. WARNING: Autopilot safety Do NOT attempt any Pilot Controller setup procedures unless the autopilot is disengaged. Selecting display type The Pilot Controller display shows one of three page views: continued ... Applicability: The procedures on this card apply to ST70+ Pilot Controllers used with Raymarine SeaTalk and SeaTalkng autopilots. They do NOT apply to ST70+ Instruments. GILKICKER POINT GILKICKER POINT Standby Rudder bar Name of next waypoint Current heading in Standby mode Locked heading when autopilot has control Mode Rudder bar Name of next waypoint Mode North indicator Data boxes Rudder bar Mode Planned track Data boxes Next waypoint Current heading (in Standby mode Locked heading (when autopilot has control) Planned track Wind direction indicator Wind direction indicator Name of next waypoint Current heading in Standby mode Locked heading when autopilot has control North indicator Plain view Compass Rose view Isometric view D11118-1 ST70+ Pilot Controller Setting up a Pilot Controller display

To change the type of view on your Pilot Controller screen, hold down MENU for 1 second. The next view in the sequence is then displayed. You can also change the view by using the menu system. To do this:. 1. Press MENU to display the Main Menu. 2. Scroll to the Pilot View option, then press OK, to display the Pilot View menu. 3. Scroll to the view you want: • Plain view, • 2D view (Compass Rose view), or • 3D view (Isometric view.) 4. Press OK to confirm the selection. Setting up data boxes You can select which data appears in the data boxes in the 2D and 3D pilot views. To do this: 1. Press MENU to display the Main Menu. 2. Scroll to Display Settings then press OK, to display the Display Settings menu. 3. Scroll to Data Boxes then press OK to select the Data Boxes menu. 4. Scroll to the data box you want to set up (1, 2 or 3) then press OK to select the setup page for that box. 5. Scroll to the data you want in the data box. A list of avail- able data for pilot Controllers is given on Card 22. 6. Press OK to return to the Data Boxes menu, and repeat steps 4 and 5 of the Setting up data boxes procedure for each data box you want to set up. Returning to operating page To return to normal operation from the Data Boxes menu, press CANCEL three times. i D11119-1 Pilot View 2D View Press OK to select 0.00 //// //// //// 0 00 //// N S W E //// //// //// //// N W E //// //// i D11120-1 Data Boxes Box 1 Select the data for box 1. Press OK to select 3 1 2 i Press OK to accept Data Boxes BTW Select data to be shown. Press CANCEL to exit without saving. D11121-1 1 ST70+ Pilot Controller Setting up a Pilot Controller display

you have full manual control, and the autopilot has no control over your boat. To enable the autopilot to steer your boat, you need to use one of the autopilot control modes. Autopilot control modes Auto mode gives the autopilot basic steering control over your boat. The autopilot steers your boat on a fixed heading that you determine. Other modes in which the autopilot has control are: • Track mode is available where GPS information is available on your system. The autopi- lot steers the boat on a pre-determined course defined by waypoints. (Refer to Card 10). • Wind Vane mode is available on SAIL BOATS ONLY, if Wind information is available. The autopilot maintains a fixed course with respect to the wind. (Refer to Card 11). • Fishing patterns are available on FISHING BOATS ONLY. The autopilot navigates the boat according a pre-programmed pattern. You can select the pattern you want and change the pattern parameters. (Refer to Card 12). Using your autopilot in Auto mode WARNING: Autopilot safety Do NOT engage your autopilot until you are sure it is safe to do so. Important To return to manual steering at any time, press STANDBY on your Pilot Controller keypad. To use your autopilot to steer your boat. 1. Manually steer your boat onto the heading you want. 2. If necessary, engage the autopilot clutch (refer to the operating guide supplied with your autopilot system). 3. Ensuring you have enough clear water in the direction of travel, press AUTO on your Pilot Controller keypad, to enter Auto mode. The autopilot then steers your boat on the heading you have chosen. If necessary, use the keypad controls to change course when running in Auto mode: • On a sail boat use either -1 or -10 to turn to port, or +1 or +10 to turn to starboard. • On a power boat turn the Rotary Control either clockwise to turn to starboard, or coun- terclockwise to turn to port. Each click of the control equals one degree of course change. Returning to manual control To return to manual steering at any time, press STANDBY. Applicability: The procedures on this card apply to ST70+ Pilot Controllers used with Raymarine SeaTalk and SeaTalkng autopilots. They do NOT apply to ST70+ Instruments. ST70+ Pilot Controller Basic autopilot operation

control: 1. At the Pilot Control keypad, press DODGE.to regain man- ual control of the boat i.e. enter Standby mode. A DODGE screen is displayed. 2. Steer the boat away from the obstacle. 3. When clear of the obstacle, press either: • AUTO to return to Auto mode steering on the previ- ous autopilot heading, or • DODGE again to return to Auto mode on the heading you are now steering. Returning to manual control To return to manual steering at any time, press STANDBY. D11041-1 Intended course Obstacle either on original course or apply new course Dodge Resume Auto Dodge course Obstacle D11123-1 ST70+ Pilot Controller Basic autopilot operation

• When using AutoTack outside of Wind Vane mode (standard AutoTack), the AutoTack angle is the angle between a port tack and a starboard tack. The default angle is 100°. . • When using AutoTack in Wind Vane mode, the tack angle relative to the wind on one tack is mirrored on the other side of the wind on the next tack. Standard AutoTack (not in Wind Vane mode) AutoTack to starboard Either: • With the Main Menu displayed, select Tack Starboard, or • Press +1 and +10 simultaneously. The boat AutoTacks to starboard. AutoTack to port Either: • With the Main Menu displayed, select Tack Port, or • Press -1 and -10 simultaneously. The boat AutoTacks to port. Trimming the helm If necessary after an AutoTack, use -1 and +1 to trim the helm to the required wind angle. Using AutoTack in Wind Vane mode Note: After an AutoTack in Wind Vane mode, the helm automatically trims to the correct wind angle. AutoTack to starboard Either: • With the Main Menu displayed, select Tack Starboard, or • Press +1 and +10 simultaneously. The boat AutoTacks to starboard. AutoTack to port Either: • With the Main Menu displayed, select Tack Port, or • Press -1 and -10 simultaneously. The boat AutoTacks to port. Applicability: The procedures on this card apply to ST70+ Pilot Controllers used with Raymarine SeaTalk and SeaTalkng autopilots ON SAIL BOATS only. They do NOT apply to ST70+ Instruments. Wind Wind Starboard tack Port tack 'Standard' AutoTack Tack angle, 100° default (can be changed in User cal) Tack angle maintained Tack angle Wind Wind Tack angle mirrored Starboard tack Port tack AutoTack in WInd Vane mode ST70+ Pilot Controller Using AutoTack

cally steer your boat along a route plotted on your chartplotter. Important To return to manual steering at any time, press STANDBY on your Pilot Controller keypad. Using track mode With your autopilot operating in Auto mode (see Card 8):. 1. Press TRACK to enter Track mode. A warning tone sounds and a warning screen is dis- played. 2. Check that it is safe for your boat to turn onto the new course, i. e. the course to the next waypoint. 3. If it is safe to apply the new course, press TRACK again. The autopilot turns your boat onto the new course and the display shows the heading required for the correct track. Waypoint arrival As you approach each waypoint, an alarm sounds and a Track mode popup is displayed: 1. Check that it is safe to turn onto the new heading, i. e. the course to the next waypoint. If it is NOT safe, press CAN- CEL to return to the previous screen and resume the previ- ous course. 2. If it is safe to apply the new course, press TRACK again to accept the new heading and proceed to the next waypoint. Skipping a waypoint If you want to bypass a waypoint when running in Track mode, hold down TRACK for 1 second. Leaving Track mode To leave Track mode, use your Pilot Controller keypad. Press either: • AUTO to return to Auto mode (autopilot control), or. • STANDBY to return to Standby mode (manual steering). Applicability: The procedures on this card apply to ST70+ Pilot Controllers used with Raymarine SeaTalk and SeaTalkng autopilots. They do NOT apply to ST70+ Instruments. D11125-1 D11126-1 ST70+ Pilot Controller Using autopilot Track mode Track leg Waypoint Waypoint Destination

same relative wind angle Wind direction New wind direction Wind shift D11127-1 Introduction On a SAIL boat, you can use Wind Vane mode to automatically maintain the boat’s heading with respect to the wind angle. Thus if the wind angle changes, the boat’s heading changes accordingly to maintain the same relative wind angle, for either true or apparent wind. Important To return to manual steering at any time, press STANDBY on your Pilot Controller keypad. Using Wind Vane mode With your autopilot operating in Standby or Auto mode: 1. Steady the boat on the required course. 2. Press MENU then use < or > as necessary to select the Wind Vane Mode option. 3. Press OK. The current boat heading is set with respect to the wind direction. The boat heading and the relative wind angle are displayed. The wind angle value is annotated either P (port) or S (starboard) as appropriate. The autopilot turns the boat as necessary to maintain the same relative wind angle. Short cut You can also enter Wind Vane mode by pressing AUTO and STANDBY simultaneously at an associated keypad. Adjusting the locked wind angle You can adjust the locked wind angle by using the -1, +1, -10 and +10 buttons to change course. For example, to bear away by 10° when the boat is on a starboard tack: • Press -10 to turn the boat 10° to port. The locked wind angle and locked heading will both change by 10°. • The autopilot will then adjust the locked heading as required to maintain the new wind angle. Note: Turning the boat affects the relationship between the true and apparent wind angles, so you should use this method only to make minor adjustments to the wind angle. For major changes, return to Standby mode, steer onto the new heading, then reselect Wind Vane mode. Leaving Wind Vane mode To leave Wind Vane mode, use your Pilot Controller keypad. Press either: • AUTO to go to Auto mode (autopilot control), or. • STANDBY to return to Standby mode (manual control). Applicability: The procedures on this card apply to ST70+ Pilot Controllers used with Raymarine SeaTalk and SeaTalkng autopilots ON SAIL BOATS only. They do NOT apply to ST70+ Instruments. D11128-1 ST70+ Pilot Controller Using autopilot Wind Vane mode

over a preset course in Auto mode. The patterns available are demonstrated in icon form, as follows: On fishing boats, the autopilot automatically recognizes your two most often used patterns over a period of time, and places these at the beginning of the menu You can customize the fishing patterns to obtain the coverage you want. Refer to the ST70+ User Reference Manual for details of customizable parameters. Procedure To use a fishing pattern: 1. At the Pilot Controller keypad, press MENU to display the Main Menu. 2. Scroll to the All patterns option and press OK to display the All pattern menu. 3. Scroll to the pattern you want to use, and press OK. 4. The Pattern settings screen is displayed, showing the parameters currently set for the selected pattern. If you want to change any of the parameters: i.Select the parameter you want to change, then press OK to select the setup screen. ii.Use the Rotary Control to set the value you want, then press OK to save the setting and return to the Pattern settings screen. iii.Repeat steps i and ii as necessary, for other parame- ters. 5. When all parameters are set as required and with the Pattern settings screen displayed, press AUTO. The autopilot then steers the boat over the fishing pattern you selected. Returning to manual control To return to manual steering at any time, press STANDBY. Applicability: The procedures on this card apply to ST70+ Pilot Controllers used with Raymarine SeaTalk and SeaTalkng autopilots on POWER BOATS only. They do NOT apply to ST70+ Instruments. Circle Zigzag Cloverleaf Spiral Circle against heading Figure 8 Pattern search 180°turn Box search D11132-1 All Patterns Circle Press OK to select i Press OK to accept Radius 150 Adjust the pattern radius. meters D11133-1 ST70+ Pilot Controller Using autopilot fishing patterns

do not need, to reduce the time it takes to access the pages you want to see. Use the proce- dure on this card to switch pages off or back on again, as required. This is a particularly useful feature if you are using the automatic rollover to select pages (see Card 14). Switching pages 1. Starting With any operational page displayed, press MENU, to dis- play the Main Menu, then scroll to the Page Layout option. Press OK to show the Page Layout menu At the Page Layout menu, scroll to the page you want to change. 2. Select option Press OK to display the setup options menu for the page you have selected. Scroll to the Turn page on/off option.Press OK to display the on/off select box 3. Select off or on Scroll to select On or Off as required. Press OK to return to the setup options menu. Returning to operating page To return to normal operation from the setup options menu press CANCEL three times.: Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They do NOT apply to ST70+ Pilot Controllers. i D11030-1 Page Layout Page 1 On Select the page you wish to configure. Press OK to select D11031-1 Page 1 Setup Turn page on/off Press OK to select i D11032-1 Press OK to accept Page 1 On CANCEL exits without saving. ST70+ Instrument Switching instrument pages on & off

after a preset period, to thus automatically display all enabled pages in sequence, one after the other. The procedures on this card enable you to: • Set a value for the rollover period, and activate the automatic rollover. • Switch off the rollover to return to manual page selection. Setting rollover 1. Starting With any operational page displayed, press MENU, to display the Main Menu, then scroll to the Display Settings option. Press OK to show the Display Settings menu. 2. Select rollover At the Display Settings menu, scroll to the Rollover option Press OK to display the Rollover setup box. 3. Set value Note: If you are using the rollover feature, it is recommended you switch off the pages you do not need (see Card 13). Scroll to set either: • the number of seconds you want each page to be dis- played, or • Off, if you want to switch off the rollover and manually select the pages you want. Press OK to save your setting and return to the Display Settings menu. Returning to operating page To return to normal operation from the Display Settings menu, press CANCEL twice. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They are NOT relevant to ST70+ Pilot Controllers. i D11033-1 Display Settings Rollover Press OK to select Automatic page rollover. i D11034-1 Press OK to accept Rollover 4 < & > adjust rollover period. CANCEL exits without saving. Secs ST70+ Instrument Setting instrument page rollover

either: • Retain the basic page layout, but change the information in individual frames on a page, as described on this card, or • Change the layout of a page by completely rebuilding it, as described on Card 16. Changing information 1. Starting With any operational page displayed, press MENU, to display the Main Menu, then scroll to the Page Layout option. Press OK to display the Page Layout menu. 2. Select the page you want to change. Scroll to the page you want to change. Press OK to display the setup options menu for the selected page. 3. Select the change item option Scroll to Change an item. Press OK to display the frame select page. 4. Select the frame you want to change Use the Rotary Control and/or PAGE UP or PAGE DN as appropriate, to move the highlight to the frame you want to change. Press OK to go to the data group select menu. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They are NOT relevant to ST70+ Pilot Controllers. i D11107-1 Page Layout Page 6 On Select the page you wish to configure. Press OK to select D11035-1 Page 1 Setup Change an item Press OK to select Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx D11036-1 Press OK to select Page 6 i Depth. Select SAVE icon and press OK to save changes. CANCEL exits without saving. ST70+ Instrument Changing information on a page

Scroll to the data group that contains the data item that you want (Depth shown here). If you don’t know which group you need, select All. Note: ST70+ supports a wide range of data. Refer to Card 21 for a full data list. Press OK to go to the data select menu. 6. Choose the data you want Scroll to: • The data you want and • The style in which you want the data displayed. The styles available depend on the data type, but in many cases, data is available in the following formats: • Analog dial. • Numeric value. • Graph. Press OK to select the data and return to the frame select menu. 7. Set up other frames To set up other frames on the current operational page, repeat the procedure from step 4 to step 6. Returning to operating page When you have completed the setup for the selected page, ensure the frame select box is displayed, then use the Rotary Control and/or PAGE UP/PAGE DN, as appropriate, to move the highlight to the Save & Exit icon. Then press either: • OK to return to your operational page, with the changes applied, or • CANCEL to return to the setup options menu, without applying the changes. To return to your operational page from here, press CANCEL three times. i D11037-1 Page 6 Frame A Depth Select the data items group. Press OK to select i D11103-1 Page 6 Frame A Minimum depth Select the new data item. Press OK to accept 0.00 //// //// //// 0 00 //// 0.00 //// //// //// 0 00 //// 0.00 //// //// //// 0 00 //// Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx Press OK to accept Page 6 i Press OK to save changes and exit. CANCEL exits without saving. D11104-1 Save & exit ST70+ Instrument Changing information on a page

Rebuilding pages 1. Starting With any operational page displayed, press MENU, to dis- play the Main Menu, then scroll to the Page Layout option. Press OK to display the Page Layout menu. 2. Select the page you want to change. Scroll to select the page you want to change. Press OK to display the Setup options menu for the selected page. 3. Select Rebuild Scroll to Rebuild. Press OK to display the Layout menu for the selected page. 4. Select page layout Scroll to the page layout you want. The following layouts are available: When you have selected the layout you want, press OK to go to the frame select box. 5. Select the frame you want to change Use the Rotary Control and/or PAGE UP/PAGE DN as appropriate, to move the highlight to the frame you want to change. Press OK to go to the data group select menu. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They are NOT relevant to ST70+ Pilot Controllers. i D11107-1 Page Layout Page 6 On Select the page you wish to configure. Press OK to select D11108-1 Page 1 Setup Rebuild Press OK to select i D11109-1 Page 1 Layout Layout 1 Select the layout you wish to use. Press OK to select Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx D11036-1 Press OK to select Page 6 i Depth. Select SAVE icon and press OK to save changes. CANCEL exits without saving. ST70+ Instrument Changing the page layout

Scroll to the data group that contains the data you want (Depth shown here). If you don’t know which group you need, select All. Note: ST70+ supports a wide range of data. Refer to Card 21 for a full data list. Press OK to go to the data select menu. 7. Choose the data you want. Scroll to the data you want, in the style you want it dis- played. The styles available depend on the data type, but in many cases, data is available in all the following formats: • Analog dial. • Numeric value. • Graph. Press OK to select the data and return to the frame select box. 8. Set up other frames Repeat step 5 to step 7, to set up the remaining frames on the selected page. Returning to operating page When you have completed the setup for the selected page, ensure the frame select box is displayed, then use the Rotary Control and/or PAGE UP/PAGE DN as appropriate, to move the highlight to the Save & Exit icon. Then press either: • OK to return to your operational page, with the changes applied, or • CANCEL to return to the setup options menu, without applying the changes. To return to your operational page from here, press CANCEL three times. i D11037-1 Page 6 Frame A Depth Select the data items group. Press OK to select i D11103-1 Page 6 Frame A Minimum depth Select the new data item. Press OK to accept 0.00 //// //// //// 0 00 //// 0.00 //// //// //// 0 00 //// 0.00 //// //// //// 0 00 //// Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx Xxx xx Press OK to accept Page 6 i Press OK to save changes and exit. CANCEL exits without saving. D11104-1 Save & exit ST70+ Instrument Changing the page layout

Initial setup 1. Select Display Settings Press MENU to display the Main Menu then scroll to Dis- play Settings. Press OK to display the Display Settings menu. 2. Select Timers At the Display Settings menu, scroll to the Timers option, then press OK. to display the Timers menu. Setting alarm clock 1. Select Alarm Clock function With the Timers menu displayed, scroll to Alarm Clock then press OK to display the Alarm Clock setup page. 2. Set alarm clock status Press PAGE UP to select the upper adjust box. Use the Rotary Control to set the alarm clock either On or Off, as required. Press PAGE DN to select the lower adjust box. 3. Adjust alarm time With the lower adjust box selected: 1. Use the rotary to select the hours box. 2. Press OK. 3. Use the Rotary Control to set the hour value for the alarm time. 4. Press OK 5. Use the Rotary Control to select the minutes box. 6. Press OK. 7. Use the Rotary Control to set the minute value for the alarm time. 8. Press OK. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They are NOT relevant to ST70+ Pilot Controllers. i D11110-1 Display Settings Timers Alarm clock and race timers. Press OK to select 100 D11111-1 Timers Alarm Clock Press OK to select i D11112-1 Press OK to accept Alarm Clock On Press CANCEL to exit without saving. : Hrs 25 07 i D11627-1 Press OK to accept Alarm Clock On Press CANCEL to exit without saving. : Hrs 25 07 ST70+ Instrument Using alarm clock

accept and save the alarm setting and display the Timers menu. Returning to operating page To return to normal operation from the Timers menu, press CANCEL three times. Alarm operation When the alarm clock is set On, the alarm buzzer will sound at the alarm time. To silence the alarm buzzer, press OK. i D11626-1 Press OK to accept Alarm Clock On Press CANCEL to exit without saving. : Hrs 25 07 ST70+ Instrument Using alarm clock

• Three race start count down timers, with default count down values as follows: • Race Start 1 - 5 minutes • Race Start 2 - 4 minutes • Race Start 3 - 1 minute. • A Race Time counter, which shows time elapsed since the start of the race. When the Race Start count down is complete, the Race Time counter counts up. If you want to set different times for the Race Start timers, use the procedure on the on the other side of this card. Operating the timers Before you can use the race timers, you must set up one of the eight instrument pages as a Race Start page. To do this, use the procedure on Card 17 to set up a single frame page containing Race Timer data. You can select the Race Timer data from the Time data group. 1. Select Race Start page Before the start of a race, use PAGE UP/PAGE DN to dis- play the Race Start page. This is displayed with Race Start timer 1 (Gun 1) timer active and the count down time displayed. If you want to use another timer, press CANCEL until the timer you want is active with the relevant start time dis- played. Note: Successive presses of CANCEL cycle around the Race Start options in the sequence Gun 1, Gun 2, Gun 3, Race Time counter, Gun 1 ... etc. 2. Start timer When the first gun fires, press OK to start the Gun 1 (default 5 minute) count down. If for any reason you cannot use the first timer (e.g. if you miss the first gun), use CANCEL to select the Gun 2 timer, then press OK to start the count down when the second gun fires. 3. Timer action When you have started a race start timer, the displayed time counts down to 0:00 (race start). During this count down period, the buzzer: • Double beeps every minute. • Beeps three times at the start of the last 30 seconds. • Beeps once per second during the last 10 seconds of count down. • Gives a 2 second beep at 0:00. From 0:00, the displayed time counts up to show the time elapsed since the race start, to a maximum of 23 hours 59 minutes and 59 seconds, and the page heading changes to Race Time. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They are NOT relevant to ST70+ Pilot Controllers. Race Start 5:00 5:00 4:00 1:00 D11600-1 ST70+ Instrument Using race timers

Use this procedure if you want to change any race start count down period. 1. Select Display Settings Press MENU to display the Main Menu then scroll to Display Settings. Press OK to display the Display Settings menu. At the Display Settings menu, scroll to the Timers option, then press OK to display the Timers menu. 2. Select Timer At the Timers menu, scroll to Set race timer then press OK to display the Set race timer setup box. Use PAGE UP to select the upper adjust box then scroll to select the race timer you want to change (Gun 1, Gun 2 or Gun 3). The value in the lower box shows the time currently set for the timer you have selected. 3. Adjust timers To change the time for the selected timer, press PAGE DN to select the lower adjust box, then use the Rotary Control to set the required value. Use this procedure for each timer you want to set. Press OK to save the setting and return to the Timers menu. Returning to operating page To return to normal operation from the Timers menu, press CANCEL three times. i D11110-1 Display Settings Timers Alarm clock and race timers. Press OK to select 100 D11113-1 Timers Set race timer Press OK to select i Press OK to accept Press CANCEL to exit without saving. D11114-1 Press OK to accept Set race timer Gun 1 5:00 ST70+ Instrument Using race timers

disable alarms. Setting up alarms 1. Enter alarm setup Press MENU to select the Main Menu then scroll to Alarms. Press OK to display the Alarms menu. 2. Select the alarm you want to set Scroll to the alarm you want to select. Note: A complete list of alarms is given on Card 21. Press OK to display an Alarm setup box. An alarm edit box is displayed. 3. Set alarm parameters Note: You cannot adjust the level of alarms set up in SeaTalk. If one of these is selected for editing you can only switch it on or off. If necessary, press PAGE UP to select the alarm status box. Where two adjust boxes are present, this is the upper box. Use the Rotary Control to switch the alarm either: • Off to disable the alarm, or • On to enable the alarm. • If a lower (alarm value) adjust box is displayed, press PAGE DN then use the Rotary Control to set the alarm value. Press OK to save the settings and return to the Alarms menu. Returning to operating page To return to normal operation from the Alarms menu, press CANCEL twice. Applicability: The procedures on this card apply to all configurations of ST70+ Instruments. They are NOT relevant to ST70+ Pilot Controllers. i D11341-1 Alarms Sea Temp. Low Adjust the low sea temperature alarm. Press OK to select i D11115-1 Sea Temp. Low Press OK to accept On Press CANCEL to exit without saving. 1 °C ST70+ Instrument Setting alarms

When an alarm occurs, a popup box is displayed on the ST70+ Instruments and an audible alarm indication may sound. The popup identifies the reason for the alarm. You can either: • Silence the alarm or • Change the parameters for that particular alarm. If an alarm occurs • To silence an alarm, press CANCEL. • To change the alarm parameters, press OK, to display the alarm setup box. Use the rele- vant procedures detailed on Card 19 to set the parameters you want for the active alarm. Alarm events The following alarm functions are supported by ST70+, although they may not all be applica- ble to your system. Alarm On-screen legend Alarm Group Apparent Wind Angle high AWA High Wind Apparent Wind Angle low AWA Low Wind Apparent Wind Speed high AWS High Wind Apparent Wind Speed low AWS Low Wind Boat speed high Boat Speed High Speed Boat speed low Boat Speed Low Speed Deep water alarm Deep Depth Deep water anchor alarm Deep Anchor Depth Man Overboard MOB - Off course Off Course Depth Sea temperature high Sea Temp. High Environment Sea temperature low Sea Temp. Low Environment Shallow water alarm Shallow Depth Shallow water anchor alarm Shallow Anchor Depth ST70+ supply battery low alarm Battery Environment True Wind Angle high TWA High Wind True Wind Angle low TWA Low Wind True Wind Speed high TWS High Wind True Wind Speed low TWS Low Wind Depth ft 9.0 Lat N Speed kts 7.0 Heading xx 63 Time 24H 11:23 o 47 o Lon o 67 D11116-1 AWS maximum Press OK to edit Press CANCEL to silence ST70+ Instrument Alarm events

the configuration of individual systems, so will not all be available on all systems. ST70+ general information Data list Data Group Air Temperature ENVIRONMENTAL Alarm deep anchor DEPTH Alarm High Apparent Wind Angle WIND Alarm High Apparent Wind Speed WIND Alarm High sea temperature ENVIRONMENTAL Alarm High speed SPEED Alarm High True Wind Angle WIND Alarm High True Wind Speed WIND Alarm Low Apparent Wind Angle WIND Alarm Low Apparent Wind Speed WIND Alarm Low sea temperature ENVIRONMENTAL Alarm Low speed SPEED Alarm Low True Wind Angle WIND Alarm Low True Wind Speed WIND Alarm maximum depth DEPTH Alarm minimum depth (shallow alarm) DEPTH Alarm off-course HEADING Alarm shallow anchor DEPTH Alarm silence ALARM Alarm waypoint arrival NAVIGATION Apparent wind angle WIND Apparent wind speed WIND Apparent wind speed maximum WIND Apparent wind speed minimum WIND Average course error HEADING Average heading HEADING Average speed SPEED Barometric pressure ENVIRONMENTAL Battery Amps ENGINE Battery temperature ENGINE Battery voltage ENGINE Beaufort WIND Boost Pressure ENGINE Bearing to waypoint NAVIGATION Calibration lock DEPTH Calibration lock WIND Cardinal WIND Course made good HEADING Course over ground GPS Course over ground + Speed over ground GPS Coolant pressure ENGINE Coolant Temperature ENGINE Course to steer PILOT Cross track error NAVIGATION Depth DEPTH Depth Offset DEPTH Depth response DEPTH Depth units DEPTH Deviation HEADING Dew point ENVIRONMENTAL Distance made good HEADING Distance made good + Course made good HEADING Distance to empty FUEL Drift ENVIRONMENTAL Distance to waypoint NAVIGATION Economy FUEL Engine hours ENGINE Engine RPM ENGINE Engine Trim Position ENGINE Estimated time of arrival NAVIGATION Fuel Flow ENGINE Fuel Level ENGINE Fuel remaining FUEL Data Group

Data list GWD WIND HDOP GPS Heading HEADING Heading response HEADING Humidity ENVIRONMENTAL Illumination SYSTEM LAT GPS Local date TIME Local time TIME Local time + date TIME Locked heading HEADING Log SPEED LON GPS Magnetic or true HEADING Max depth DEPTH Max speed SPEED Maximum air temperature ENVIRONMENTAL Maximum sea temperature ENVIRONMENTAL Minimum depth DEPTH Minimum air temperature ENVIRONMENTAL Minimum sea temperature ENVIRONMENTAL MOB MOB Oil Pressure ENGINE Oil Temperature ENGINE Rate of turn BOAT Race Start timer TIME SATS GPS SATS + HDOP GPS Sea temperature ENVIRONMENTAL Serial number DIAGNOSTIC Set ENVIRONMENTAL Software version DIAGNOSTIC Speed over ground GPS Speed SPEED Speed adjust SPEED Speed response SPEED Speed through water + Speed over ground GPS Data Group Sunset / Sunrise ENVIRONMENTAL Tack heading HEADING Temperature offset ENVIRONMENTAL Temperature units ENVIRONMENTAL Tilt BOAT Trim tabs BOAT Trip DISTANCE True wind angle WIND True wind speed WIND Variation HEADING VMG to waypoint SPEED VMG to windward SPEED Wind angle response WIND Wind chill apparent ENVIRONMENTAL Wind chill true ENVIRONMENTAL Wind speed response WIND Data Group