Panasonic MC-UL862 Operating Instructions Manual

to operate the vacuum cleaner and that you note the Important Safety Instructions. Please keep in a safe place with your Authorised Dealer Service booklet. This product complies with the European directive 73/23/EEC and 89/336/EEC and with the Australian Standards AS 3350.2.2 (1995) and Australian EMC requirements for the C-Tick Mark. OFF HIGH LOW Operating Instructions Vacuum Cleaner Model No. MC-UL862 Matsushita Electric Industrial Co., Ltd http://www.panasonic.co.jp/global/ © 2006 Matsushita Electric Industrial Co., Ltd. All rights Reserved. CØ1ZCWZ3ØEØØ ACØ1ZCWZZØEØ Printed in Mexico REMINDER FOR CUSTOMER The model and serial number of the product may be found on the nameplate located at the back of your vacuum cleaner. You should note the model and serial number in the spaces provided and retain this book for future reference. Model Number: .................................... Serial Number:...................................... Date Purchased: .................................. Where Purchased:................................

Page • Caution for AC Mains Lead (UK and Republic of Ireland only) ..........2 • Important Safety Instructions for the user ..........................................3 • Cautions ............................................................................................3 • Identification of main parts ................................................................4 HOW TO OPERATE YOUR VACUUM CLEANER A) Assembly........................................................................................ 4 B) Mains lead release ..........................................................................5 C) ON/OFF Switch ..............................................................................5 D) How to use adjustable handle ........................................................5 E) Handle lock / release by foot pedal ................................................5 F) Carpet / Bare Floor Selector ..........................................................6 G) How to use accessories ..................................................................6 H) Motor protector ................................................................................7 I) Thermal cut-out ................................................................................7 TABLE OF CONTENTS Page MAINTENANCE AND SERVICING A) Cleaning exterior and attachments ......................8 B) Dust bin cleaning and removal..............................8 C) Dust bin filter changing and cleaning ........................9 D) Cleaning secondary filter ..................................10 E) Exhaust filter cleaning ........................................10 F) Belt changing cleaning ........................................11 G) Blockages............................................................12 H) Troubleshooting guide ........................................13 • Specifications ........................................................14 • Consumables / accessories ..................................15 FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has rating of 13 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. How to replace the Fuse: • There are two types of the supplied AC Mains Lead : A and B as shown below. 1 Open the fuse compartment with a screwdriver. 2 Replace the fuse and fuse cover if detachable. ASA CAUTION FOR AC MAINS LEAD (UK and Republic of Ireland only) TYPE A TYPE B Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. - 17 - IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT OR SIMILAR QUALIFIED PERSONS IN ORDER TO AVOID HAZARD. CAUTION

the appliance or undertaking maintenance operations. • This appliance is not intended for use by young children or infirm people without supervision; young children should be supervised to ensure that they do not play with the appliance. • Do not use if the mains lead or mains plug is damaged. If the vacuum cleaner is not working as it should be, or has been dropped, damaged, left outdoors, or come into contact with water, consult an authorised Panasonic Service Centre. • Do not pull or carry by the mains lead, use the mains lead as a handle, close a door on the mains lead, pull the mains lead around sharp edges or corners. Do not run over the mains lead with the vacuum cleaner. Keep the mains lead away from heated surfaces. • Do not handle plug or vacuum cleaner with wet hands. • Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may block or reduce air flow. • Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. • Do not use the vacuum cleaner without filters and /or dust bin in place. • Do not use wet filters after wash, see C) Dust Bin Filter Changing and Cleaning. • Turn off all controls before unplugging. • Do not use to pick up flammable or combustible materials, or others that may become so or use in areas where they may be present. • This appliance should be serviced by an authorised Panasonic Service Centre, and only genuine Panasonic spare parts should be used. • Use extra care when cleaning on stairs. Keep hold of the handle to prevent the vacuum cleaner from falling. • To prevent damaging carpeted floors, tiled floors, Linoleum, etc. Do not leave the beater bar rotating in the same place for too long. • Keep bare feet and hands away from the beater bar. (It may cause injury) NOTE: This vacuum cleaner is designed for general household use only and is not suitable for use in a garage, garden or to suck up liquids. IMPORTANT SAFETY INSTRUCTIONS FOR THE USER Before using the vacuum cleaner, please read these basic precautions. WARNING: To reduce the risk of fire, electric shock, or injury. NOTES CAUTION 1. To avoid any possible damage to the mains lead, never run over the mains lead or allow it to become caught in the beater bar when using the vacuum cleaner. 2. Do not run the vacuum cleaner over tassels or fringes of rugs or mats as they could get caught up in the beater bar and may cause damage to belt. 3. Keep the vacuum cleaner away from heat sources such as radiators, fires, direct sunlight, etc. 4. To avoid damaging the machine, never let the vacuum cleaner pick up wet matter, mud, burning ashes or large and sharp objects. 5. Do not pull on the mains lead when disconnecting the appliance from the mains, always pull on the plug body itself. 6. To avoid injury, keep your fingers and hands away from the beater bar, and never put them between the body parts. OFF HIGH LOW - 3 - - 16 -

Extension Hose Air Turbine Upper Cord Hook Hose Ring Handle Length Adjustment Carrying Handle Mains Lead Lower Cord Hook Adjustable Handle Release Button Motor Protector Nozzle Hose Adjustable Handle ON/OFF Switch Dust Bin Lid Release Dust Bin Release Latch Dust Bin Exhaust Filter (inside) Cleaning Hood Furniture Guard Dusting Brush Crevice Tool Floor Brush Carpet/Bare Floor Pedal Body Release Pedal A) ASSEMBLY - 4 - ➀ Insert adjustable handle assembly as illustrated. ➁ Attach hose end to vacuum cleaner as illustrated. ➂ Insert hose onto handle. ➃ Attach hose ring to vacuum cleaner body where indicated. ➄ Place extension hose behind hose holder where indicated. ➅ Wrap mains lead clockwise around upper and lower cord hooks as shown. ➆ Insert air turbine into holder on vacuum cleaner body as indicated. Air Turbine Mains Lead Adjustable Handle Hose Ring Hose Holder Extension Hose 1 2 3 4 5 6 7 HOW TO OPERATE YOUR VACUUM CLEANER - 15 - Vacuum Cleaner Consumables / Accessories For customers within the UK: For customers within the Republic of Ireland: DESCRIPTION MC-UL862 Primary Filter Part number AC95KBRN3ØØØ Exhaust filter Part number HEPA Filter Type F-2H AC38KBRMZØØØ Dust Box Unit Part number AC85KCNFZØØØ Handle Unit Part Number AC95BCNFZØØØ Floor Nozzle Brush Part Number AC96RCNFZVØ6 Crevice nozzle Part number AC6ØRCNFZVØ6 Dusting Brush Part number AC88RCNFZVØ6 Air Turbine Part number AC80SCWZZVØ7 Belt Part number AC28SCNZZØØ Beater Bar Assembly Part number AC84RCWZZØØØ Hose Part number AC84PCNFZVØ6 Note: Specifications are subject to change without notice. Sales and Support Information Customer Care Centre • For customers within the UK: 08705 357357 • For customers within the Republic of Ireland: 01 289 8333 • Visit out website for product information • E-mail: [email protected] Direct sales at Panasonic UK • Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm (excluding public holidays). • Or go on line through our Internet Accessory ordering application at www.panasonic.co.uk • Most major credit and debit cards accepted. • All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. • It couldn’t be simpler! • Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details.

C) ON/OFF SWITCH E) HANDLE LOCK / RELEASE BY FOOT PEDAL Release the handle by pressing down on the handle release pedal with your foot and pulling back and down on the handle with your hand. Step on the handle release pedal a second time to lower the vacuum cleaner to the low position for cleaning under furniture CAUTION: To prevent damaging carpeted floors, tiled floors, linoleum, etc. Do not leave the beater bar rotating in the same place for too long. Wrap the mains lead around the upper and lower cord hooks and push the mains plug under the lead. Turn the upper cord hook to release the mains lead. To start or stop the vacuum cleaner, push the switch button to ‘I’ to turn ON and to ‘O’ to turn OFF. NOTE: After use, unplug from the socket and store the vacuum cleaner in the upright position. 1 Cord Hook 12 O I ON/OFF Switch O I 1 12 D) USING ADJUSTABLE HANDLE Press the handle length adjust button located on the back of the vacuum cleaner. Raise or lower the adjustable handle to the desired operating position. - 5 - Length Adjust Button Adjustable Handle 1 - 14 - MODEL NO. MC-UL862 POWER SOURCE 230-240V / 50Hz MAX. INPUT POWER 1800w MOTOR PROTECTION YES DUST BIN CAPACITY 2.5 litres EXHAUST FILTER HEPA DIMENSIONS (W x L x H) 360x375x1110 NET WEIGHT 8.6 kg DUSTING BRUSH YES MINI TURBINE YES CREVICE NOZZLE YES CLEANING WIDTH 381mm SPECIFICATIONS

G) HOW TO USE THE ACCESSORIES Adjustable Handle Release Hose Ring Lift adjustable handle by pushing the adjustable handle release button to the right. Release the hose ring. 1 1 2 3 4 With the handle out of the vacuum cleaner it can now be used as an extension wand. Length can be changed when using as a wand. 12 F) CARPET/BARE FLOOR SELECTOR CAUTION: To prevent damaging carpeted floors, tiled floors, linoleum, etc. Do not leave the beater bar rotating in the same place for too long. To Clean Bare Floor Or Use Tools NOTE: After use, unplug from the socket and store the vacuum cleaner in the upright position. 12 The beater bar does not rotate in the BARE FLOOR (TOOLS) position. Selector should be placed in BARE FLOOR (TOOLS) position when using vacuum cleaner on bare floors and when using tools. To Clean Carpet 13 Selector should be placed in CARPET position when using vacuum cleaner on carpeted floors. NOTE: For longer belt life, turn vacuum cleaner off before moving selector. CAUTION: Failure to do so can cause belt to rub on selector shaft and result in belt becoming hot and creating a burning rubber smell. - 13 - H) TROUBLE SHOOTING GUIDE Before contacting your Panasonic service centre, check the following points: NOTE: Failure to correctly maintain your product, for example regular cleaning and unblocking, may result in a charge if referred to a service agent for attention. CAUTION:DISCONNECT from the mains socket before carrying out any kind of maintenance operation. TROUBLE CHECK POINT CAUSE / REMEDY Motor fails to rotate • Mains plug connection • Check that the mains plug is connected firmly and (no noise is heard at all) mains socket is ON. • Mains plug fuse. (UK, IRL only) • Check fuse and replace if blown. • Thermal cut-out device may have • (See Thermal cut-out protection feature below operated. described). Motor runs but there • Hose inlet is blocked. • If there is a blockage, remove it. is no suction. see (BLOCKAGES) • Check dust mark. • If it shows full, empty the dust compartment. • Primary filter • If the primary filter is full of dust, clean it or replace. (see FILTER CARE) • Check hose is properly inserted • Re-insert the hose to suction pipe inlet correctly. to the suction pipe inlet. • Check dust accumulated on primary • Remove dust accumulated or replace the filters. filter. (see FILTER CARE) • Exhaust filter. • If exhaust filter is full of dust, clean or replace it. (see FILTER CARE) • Dust compartment inlet is blocked. • If there is a blockage, remove it. (see BLOCKAGES) Beater bar does not • Clogged by a large object in • If there is any obstruction, remove it. rotate. the beater bar housing. • Belts broken or loose. • If the belt is broken, replace it. If loose re-install it. THERMAL CUT-OUT This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the vacuum cleaner to prevent overheating of the motor. When this happens, disconnect the vacuum cleaner from the mains socket and check the dust compartment and filters as it may be full or clogged with fine dust. Check for any other obstructions. After emptying the dust compartment or removing the obstruction, leave the vacuum cleaner to cool down until the thermal cut- out resets after approximately 40 minutes. IMPORTANT: The thermal cut-out will not reset if the vacuum cleaner is not disconnected from the mains socket. MAINS LEAD IMPORTANT: If the mains lead becomes damaged, it must be repaired by Panasonic, authorised service centre or a qualified person in order to avoid any hazard. NOTE: After using the accessories, re-insert the hose into the suction pipe inlet by aligning tabs on the handle assembly with slots on the body as shown. Reattach hose ring. Tabs Slot 13 CAUTION: To prevent damaging carpeted floors, tiled floors, linoleum, etc. when using tools the Carpet/Bare Floor selector should be placed in the BARE FLOOR (TOOLS) position. CAUTION: To avoid accidental injury, keep children away from the beater bar while in operation. Carpet/Bare Floor Selector CARPET BARE FLOOR (TOOLS) 1

automatically trips to protect the vacuum cleaner from overheating. If a clog prevents the normal flow of air to the motor, the thermal cut-out turns the motor off automatically to allow the motor to cool in order to prevent possible damage to the vacuum cleaner. To correct problem: If this occurs, turn the vacuum cleaner off and unplug the vacuum cleaner from the mains outlet to allow the vacuum cleaner to cool and the thermal cut-out to reset. Check for and remove clogs, if necessary. Also check and clean/replace any clogged filters. Wait approximately forty (40) minutes before switching on the vacuum cleaner. The motor protector will not reset if the vacuum cleaner is not turned off even if the vacuum cleaner has cooled down. H) MOTOR PROTECTOR Motor Protector This vacuum cleaner has a motor protector by-pass valve which automatically opens to provide cooling air to the motor when a clog prevents the normal flow of air to the motor. If the by-pass valve opens to prevent motor overheating and possible damage to the vacuum cleaner, you will notice a change of sound as air rushes through the valve opening. To correct problem: See the TROUBLE-SHOOTING guide (page 13). NOTE: The motor protector may open when using attachments or when cleaning new carpet, due to reduced airflow by the attachments themselves or by new carpet fluff filling the dust bin quickly. See the TROUBLE- SHOOTING guide (page 13). I) THERMAL CUT-OUT CAUTION: Do not block motor protector. - 7 - - 12 - 14 Secondary Filter Screen 15 If the vacuum cleaner does not seem to have adequate suction, first check if the dust bin is full or if a filter is clogged. Check the hose area. Remove extension hose by grasping the hose collar, twisting, and pulling straight off. Visually inspect the hose and the base area into which the hose is connected. Remove any visible clog. Re-connect the extension hose to the dust bin port assembly. Plug in the vacuum cleaner and turn it on. Stretch the hose to maximum length and then allow the hose to return to its storage length. Turn the vacuum cleaner off and unplug the vacuum cleaner. Remove dust bin and check secondary filter screen for clogs. If the dust bin and filter areas and the hose areas are free of clogs, check the nozzle area. Return the vacuum cleaner to the upright position before plugging into an electrical outlet. G) BLOCKAGES

Always follow all safety precautions when cleaning and servicing the vacuum cleaner. WARNING: Electrical Shock And Personal Injury Hazard Disconnect from electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting. A) CLEANING EXTERIOR AND ATTACHMENTS CAUTION:Do not use attachments if they are wet. Attachments used in dirty areas, such as under a refrigerator, should not be used on other surfaces until they are washed. They could leave marks. Disconnect mains plug from wall outlet. Clean exterior using a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry. Wipe dry after cleaning. DO NOT drip water on vacuum cleaner. Wash attachments in warm soapy water, rinse and air dry. Do not clean in dishwasher. DO NOT use tools if they are wet. - 8 - To replace dust bin, align base of dust bin with the cleaner and rotate the dust bin into the vacuum cleaner until the dust bin latch locks securely in place. OFF MAX 1 B) DUST BIN CLEANING Grasp the handle on the top of the dust bin. Slide the dust bin latch down. Lift up and out to remove dust bin from vacuum cleaner. Every time dust bin is removed, rotate cleaning knob on top of dust bin until filter is clean to maintain cleaning performance. CAUTION: Electrical Shock And Personal Injury Hazard Always disconnect the vacuum cleaner from mains outlet before carrying out any service or maintenance on the vacuum cleaner. Cleaning Knob MAX Dust Bin Emptying Door Dust Bin Lid Release Always empty the dust bin when dirt level reaches the “MAX FILL” line. 12 13 Dust Bin Handle Dust Bin Latch OFF MAX MAX 1 Press dust bin lid release and the dust bin will open and the debris will fall out into a trash container. Usage Clean Beater bar HEAVY - every week (used daily) MODERATE - every month (used 2-3 times/week) LIGHT - every 2 months (used 1 time/week) - 11 - F) BELT CHANGING AND CLEANING WARNING: Electrical Shock And Personal Injury Hazard Disconnect from electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting. Frequently check and remove hair, string and lint build-up in the brush area. If build-up becomes excessive, follow the steps below. Should the belt become loose or should it break, follow the Belt Removal Instructions. Always place paper under nozzle whenever lower plate is removed to protect floor. Place body in upright position and turn vacuum cleaner over to expose lower plate. Release lower plate by removing two (2) screws and pressing two (2) locking tabs as shown. Remove lower plate and remove any residue that may exist in belt area. Place carpet-bare floor selector in CARPET position. Remove lower plate as shown above. Remove agitator by carefully lifting out. Remove worn or broken belt. Seat the right side of the beater bar into the nozzle base. To seat beater bar, place rounded portion of the beater bar end cap into the slot in the nozzle base. Loop the new belt on the motor shaft. Loop the other end of the belt on to the belt pulley on the left side of the beater bar. Pull the left side of the beater bar forward and seat it into the nozzle base. After reinstalling the agitator, press firmly to see that each end cap is completely inserted. Turn the beater bar by hand to make sure that belt is not twisted or pinched and that all rotating parts turn freely. Locking Tab Screws Locking Tab 1 Beater bar Belt Motor Shaft 12 Reinstall the lower plate by hooking the front end of the lower plate into slots on the front of nozzle housing. Tabs Lower Plate 15 Rotate the lower plate until the locking tabs snap into place. Replace two (2) screws. Locking Tab Screws Locking Tab 16 Belt Motor Shaft Belt Groove Carpet/Bare Floor Selector Shaft 13 Beater Bar Belt End Cap 14 WARNING: Personal Injury Hazard Always unplug the vacuum cleaner before cleaning the brush area as beater bar may suddenly restart. Failure to do so can result in personal injury. WARNING: Personal Injury Hazard Be careful when removing the beater bar as the belt tension is high. Failure to do so could result in personal injury from the beater bar releasing quickly and snapping away. NOTE: In order to keep cleaning efficiency high and to prevent damage to your vacuum cleaner, the beater bar must be cleaned every time the belt is changed. 4

C) DUST BIN FILTER CHANGING AND CLEANING Check primary filter frequently and clean when dirty. Remove the dust bin assembly as outlined in the DUST BIN CLEANING section and empty contents of dust bin. Dust Bin Emptying Door Dust Bin Lid Release 1 To remove primary filter, open dust bin lid assembly as outlined in the DUST BIN CLEANING section. While holding primary filter over a trash container grasp filter, rotate counter-clockwise and remove from filter support. Cean primary filter by gently tapping over a trash container. Tap on several sides to ensure best cleaning. CAUTION: Make sure dust bin is empty before filter is removed. CAUTION: Rinse with water only, do not use detergent or soap. Allow filter to dry 24 hours before putting it back into the dust bin. When the cleaning of the filter no longer restores vacuum cleaner suction to full power you need to replace the filter. Before replacing the primary filter it is a good idea to clean the inside of the dust bin. CAUTION: When cleaning filter, do not use brush or other simular tools that would damage the filter itself. Simply tap the filter on the edge of cap for normal dry cleaning. For more thorough cleaning, rinse outside of filter with water and allow to dry thoroughly before reuse in vacuum cleaner. Cleaning Cams Filter Supporter Primary Filter 12 Rotate filter clockwise until slots lock onto tabs in lid. Door latch 13 After the dust bin is empty of debris, firmly close the door. Make sure you hear a “click” sound to indicate that the door is fully latched. - 10 - D) CLEANING SECONDARY FILTER SCREEN The secondary filter screen protects the motor. Always check filter screen when cleaning dust bin. If dirty or clogged, remove debris from filter screen. Secondary Filter Screen E) EXHAUST FILTER MAINTENANCE Press Release Tab The exhaust filter removes dirt from recirculated air. Check filter after emptying dust bin. To remove, press release tab and rotate off. Grasp the exhaust filter and pull out to remove. When replacing the exhaust filter, ensure foam edge of the filter is facing towards the vacuum cleaner when placing filter into filter compartment. Push only on filter frame. Reinstall exhaust filter cover by snapping into place. IMPORTANT - Filter cannot be cleaned and should be replaced at least once each year. Exhaust Filter Cover Exhaust Filter Tab 1 12 Exhaust Filter Cover Tab Slot Exhaust Filter 13