PCE Instruments PCE-FWS-20 Manual 

of transmitter will be turned on for 4 seconds, and then it will be off and start to work normally. The transmitter will make a data transmission and then start radio controlled time reception routine. If time signal can be detected correctly, then the LED will start to flash 5 times indicating time signal has been found correctly. When time signal is bad and reception is not possible, the transmitter will terminate radio controlled time reception wi ...

button will be flashing. Touch the + button or – button to Shift the display between Absolute pressure and Relative pressure. 2. Touch the PRESSURE section again, + button and – button will be flashing. Touch the + button or – button to Shift the display unit between hPa, inHg and mmHg. 3. Touch the PRESSURE section the third time to set the Relative Pressure value. The + and – button will be flashing, rel icon will light up. Touch the + button or – button to change the value, hold the + button or – button for ...

1. Touch the rain section, + button and – button will be flashing. Touch the + button or – button to Shift the display between 1h,24h,week,month and total rain. 2. Touch the rain section again, + button and – button will be flashing. Touch the + button or – button to select rain fall unit between mm, inch. 3. Touch the rain section the third time to set the high alarm function, the +, ON/OFF and – button will be flashing, HI AL icon will light up. Touch the + button or – button to change the value, hold the + button or – b ...

100 m (330 feet) Frequency 868 MHz (Europe) / 915 MHz (North America) Temperature range -40°C … 65°C (-40 ℉ to +149 ℉) Resolution 0.1 °C (0.2 ℉) Measuring range rel. humidity 10 … 90 % Rain volume display 0 … 9999mm (show --- if outside range) Resolution 0.1mm (if rain volume < 1000mm) 1mm (if rain volume > 1000mm) Wind speed 0…240km/h (0…100mph) (show --- if outside range) Measuring interval thermo-hygro sensor 48 s Water proof level IPX3 Indoor data Measuring interval pressure / temperature 48 s Indo ...

time period and press “Search” to reload the history data. The export button transfers the selected saved data in to other applications. When the memory on the base station is full, press “Clear Memory” button to refresh the memory capacity on the base station (remember to upload all data before pressing this button). ...

7.6 Troubleshooting: Graphs are not being displayed This is the most encountered problem with this software. To make sure the graph will be displayed, proceed as follows: 1. Find the folder in which the “EasyWeahter.exe” file is located. 2. Create a file name “reg_graph.bat” file with word pad or notepad editor programme (Make sure that Windows saves the file with the correct ending and not as “reg_graph.bat.txt” – the file name in front of the point is not relevant. 3. Give in “regsvr32 easyweather.ocx” (without quotation m ...

button will be flashing. Touch the + button or – button to Shift the display between Absolute pressure and Relative pressure. 2. Touch the PRESSURE section again, + button and – button will be flashing. Touch the + button or – button to Shift the display unit between hPa, inHg and mmHg. 3. Touch the PRESSURE section the third time to set the Relative Pressure value. The + and – button will be flashing, rel icon will light up. Touch the + button or – button to change the value, hold the + button or – button for ...

7.6 Troubleshooting: Graphs are not being displayed This is the most encountered problem with this software. To make sure the graph will be displayed, proceed as follows: 1. Find the folder in which the “EasyWeahter.exe” file is located. 2. Create a file name “reg_graph.bat” file with word pad or notepad editor programme (Make sure that Windows saves the file with the correct ending and not as “reg_graph.bat.txt” – the file name in front of the point is not relevant. 3. Give in “regsvr32 easyweather.ocx” (without quotation m ...