Toro 22303 Dingo 320-D Operator's Manual

Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 108-9733 1. Warning—read the Operator’s Manual. 4. Arm lift— up 7. Bucket tilt— down 10. Engine—run 2. Tipping hazard—do not step off operator platform with load raised, always operate with the heavy end of the machine pointed uphill, carry loads low, maximum load is 515 lb (234 kg). 5. Wheel drive—forward 8. Bucket tilt—up 11. Engine—stop 3. Arm lift–down 6. Wheel drive—reverse 9. E ...

the hydraulic connectors. 6. Push the attachment male connector into the female connector on the traction unit. Note: When you connect the attachment male connector first, you will relieve any pressure build up in the attachment. Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Fluid injected into the skin must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result. • Keep your body and hands away from pin hole leaks or nozzles that eject high pressure hydrau ...

3. Engine temperature light 2. Battery light 4. Glow plug light Battery Light This light (Figure 10) is on for a few seconds whenever you start the engine. If the battery light is on while the engine is running, the alternator, battery, or electrical system is broken. Contact your Authorized Toro Dealer for diagnostics and repair. Engine Temperature Light If the engine temperature light (Figure 10) is on, the engine is overheating. Stop the engine and allow the traction unit to cool down. Check the coolant level and the belts to the fan and water pump. Fill the ...

10. Start the engine and let it run for about two minutes to purge air from the system. 11. Stop the engine and check for leaks. 12. Check the fluid level in the hydraulic tank (refer to Checking the Hydraulic Fluid, in Operation) and add fluid to raise the level to the mark on the dipstick. Do not over fill the tank. 13. Install the front access cover. 14. Remove and store the cylinder locks and lower the loader arms. Changing the Hydraulic Fluid Change the hydraulic fluid yearly. 1. Position traction unit on a level surface. 2. Raise the loader arms and in ...

Step Description Qty. Use 1 Speed selector lever 1 Install the speed selector lever. 2 No parts required – Charge and connect the battery. 3 No parts required – Check the uid levels. Step 1 Installing the Speed Selector Lever Parts needed for this step: 1 Speed selector lever Procedure 1. Remove and discard the nut securing the bolt and washer to the speed selector lever. 2. Secure the lever to the speed selector valve using the bolt and washer as illustrated in Figure 3. Note: The lever should be installe ...

93-6686 1. Hydraulic oil 2. Read the Operator’s Manual. 106-5976 1. Engine coolant under pressure 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator’s Manual. 4. Warning—read the Operator’s Manual. Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No re, open ame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 8. Battery acid can c ...

Cover ................................ 26 Lubrication................................................ 26 Greasing the Traction Unit................. 26 Engine Maintenance.................................. 27 Servicing the Air Cleaner ................... 27 Servicing the Engine Oil .................... 28 Fuel System Maintenance .......................... 29 Changing the Fuel Filter..................... 29 Bleeding the Fuel System ................... 30 Draining the Fuel Tank...................... 30 Electrical System Maintenance................... 31 Servicing the Batte ...