Toro ProLine 30196 Operator's Manual

Form No. 3323–734 ProLine 14 HP – 48� Mid-Size Mower 30196—200000001 & Up ...

All Rights Reserved Introduction Thank you for purchasing a Toro product. All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your local Authorized Service Dealer for help with service, genuine replacement parts, or other information you may require. Whenever you contact your Authorized Service Dealer or the factory, always know the model and serial numbers of your product. These numbers will help the Service Dealer or Service Representative provide exact information about your specific product. You will find the model and serial number plate located in a unique place on the ...

Safe Operating Practices 2 . . . . . . . . . . . . . . Toro Mower Safety 4 . . . . . . . . . . . . . . . . . . Slope Chart 7 . . . . . . . . . . . . . . . . . . . . . . . . . Safety and Instruction Decals 9 . . . . . . . . . . . Gasoline and Oil 11 . . . . . . . . . . . . . . . . . . . . . . . . Recommended Gasoline 11 . . . . . . . . . . . . . . . Using Stabilizer/Conditioner 12 . . . . . . . . . . . Filling the Fuel Tank 12 . . . . . . . . . . . . . . . . . Check Engine Oil Level 12 . . . . . . . . . . . . . . . Assembly 13 . . . . . . . . . . . . . . . . . . . ...

requirements for rotary mowers and the B71.4 1999 specifications of the American National Standards Institute, in effect at time of production. Note: The addition of certain attachments that do not meet American National Standards Institute certification will cause noncertification of this machine. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER—“personal safety instruction.” Failure to comply with t ...

• Only operate in good light, keeping away from holes and hidden hazards. • Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided. • Be sure of your footing while using pedestrian controlled equipment, especially when backing up. Walk, don’t run. Never operate on wet grass. Reduced footing could cause slipping. • Slow down and use extra care on hillsides. Be sure to travel in the recommended direction on hillsides. Turf conditions can affect the machine’s stability. Use ...

before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last. • Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them. • Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running. • Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools. • K ...

which may be hot from operation. Allow to cool before attempting to maintain, adjust or service. • Before operating a machine with ROPS (roll over protection) be certain the seat belts are attached to prevent the seat from pivoting forward. Slope Operation Slopes and ramps are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes and ramps require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. DO • Mow up and down slopes greater than 5°, not across. • Mow downhill only on slopes ab ...

that original standards are maintained. • Check brake operation frequently. Adjust and service as required. • Battery acid is poisonous and can cause burns. Avoid contact with skin, eyes and clothing. Protect your face, eyes and clothing when working with a battery. • Battery gases can explode. Keep cigarettes, sparks and flames away from battery. • Hydraulic fluid escaping under pressure can penetrate the skin and cause injury. Use cardboard or paper to find hydraulic leaks. • Never modify ROPS (roll over protection) frames or structures because they are specifically designed, sized, ...

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. �� ����� ������� ��� ����� ��� �������� �� ��������� �� ����� ����� ��� �������� �� ����� ������� ��� ����� ��� �������� �� �������� ���� �� ����� ����� ��� �������� ����� �� ...

����� ��� �������� �� ������� ����� ����� ��� �������� �� ���� ���� �� ������ ����� ����� ��� �������� ����� ���� ���� �� ���� ���� ����� ��� �������� �� ���� ����� ����� ��� �������� �� ��������� ������ �� ����� ����� ��� ������ ...

Recommended Gasoline Use UNLEADED Regular Gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. IMPORTANT: Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline. POTENTIAL HAZARD • In certain conditions gasoline is extremely flammable and highly explosive. WHAT CAN HAPPEN • A fire or explosion from gasoline can burn you, others, and cause property damage. HOW TO AVOID THE HAZARD • Use a funnel and fill the fuel tank outdoors, in an open ...

12 POTENTIAL HAZARD • Gasoline is harmful or fatal if swallowed. Long–term eposure to vapors has caused cancer to laboratory animals. WHAT CAN HAPPEN • Failure to use caution may result in serious injury or illness HOW TO AVOID THE HAZARD • Avoid prolonged breathing of vapors. • Keep face away from nozzle and gas tank or conditioner opening. • Keep gas away from eyes and skin. Using Stabilizer/Conditioner Use a fuel stabilizer/conditioner in the machine to provide the following benefits: • Keeps gasoline fresh during storage of 90 days or less. For longer storage, drain the fuel tank. • Cleans the engine while it runs ...

DESCRIPTION QTY. USE Castor assemblies Bolt 3/8–16 x 3/4” (19 mm) Flange nut 3/8–16 2 8 8 Install front castors to mower Upper handle Bolt 3/8–16 x 1” (26 mm) Locknut 3/8–16 Plastic terminal Wire tie 1 4 4 1 1 Install upper handle to frame Install wire harness to handle Rod fitting Clevis pin Washer 1/4” Hairpin cotter 2 2 2 4 Install traction control rods PTO rod Hairpin cotter 1 2 Install PTO rod Shift lever Rubber seal Square hole washer Spring washer Locknut 1 1 1 1 1 Install shift lever to transmission ...

Lock washer 5/16” Washer 5/16” Stud Spring Hose clamp 1 2 2 4 2 2 1 Install fuel tank Operator’s Manual Engine Operator’s Manual Parts Catalog Registration card 1 1 1 1 Read before operating machine Fill out and return to Toro Install Front Castors 1. Align castors with holes on top and front of mower and insert (8) 3/8–16 x 3/4” (19 mm) bolts through mower. Secure with (8) 3/8–16 flange nuts below mower (Fig. 1). Note: Tighten lower bolts first to pull castor against front, then top bolts last. 2. Torque bolts to 30–35 ft. lb. (40–47 N�m). � � m–377 ...

4. Route wire harness inside of frame, along left handle and over throttle cable. Compress wire harness covering and press into lower and upper holes in rear of control panel (Fig. 3). 5. Thread harness up through rear tube of traction handle (Fig. 3). m–3774 � � � � Figure 3 1. Wire harness 2. Control panel 3. Tube 4. Wire tie 6. Insert terminals into plastic plug until the clips snap into position (Fig. 3). If they do not snap turn around and try again. 7. Push plug onto switch so latches interlock (Fig. 3). 8. Secure wire harness and throttle cable to left handle, away from PTO lever, with wire tie (Fig. 3) ...

fixed bar with wheel drive fully engaged. Gap should be approximately 1 to 1-1/4 in. (25–32 mm) (Fig. 6). Note: The upper control bar and fixed bar must be parallel in the engaged, relaxed and brake positions. 4. Check operation. If adjustment is required, remove hairpin cotter securing rod to upper control bar. Thread rod in or out of fitting for proper position and install into upper control bar with hairpin cotter. 5. After adjusting control rods, check parking brake adjustment, refer to: Brake page 36 for instructions. m–3770 � � � � Figure 6 1. Control rod 2. Fixed control bar ...

Rod 1. Rotate blade control lever (PTO) vertical away from left handle so rod drops down. 2. Remove hairpin cotters from bottom end of blade control rod (PTO) (Fig. 8). 3. Secure blade control (PTO) rod through hole in bellcrank with hairpin cotters (Fig. 8). m–3783 � � � � Figure 8 1. Blade control lever 2. Blade control rod 3. Bellcrank 4. Hairpin cotter Install Shift Lever 1. Remove the 3/8” locknut and spring disk washer from the stud on top of the transmission. Note: Do not remove rubber seal washer and square hole washer from transmission shaft. 2. Slide shift lever through control panel and ali ...

1. Align fuel tank to top of rear frame and secure fuel tank right side with (2) 5/16–18 x 7/8 in. (22.5 mm) bolts, (2) 5/16 lock washers and (2) 5/16 washers (Fig. 10). 2. Secure fuel tank left side to frame with (2) 5/16–18 x 7/8 in. (22.5 mm) studs, (2) 5/16 washers and (2) 5/16 locknuts (Fig. 10). m–3771 1 2 3 5 4 6 3 Figure 10 1. Bolt 5/8–18 x 7/8” (22.5 mm) 2. Lock washer 5/16 3. Washer 5/16 4. Stud 5. Spring 6. Locknut 3. Push fuel line onto fuel tank fitting and secure with hose clamp (Fig. 11). m–3778 1 2 3 Figure 11 1. Fuel line 2. Hose clamp 3. Fuel fitting ...