Sony VPL-FE110U Operating Instructions Manual

4-080-673-42(1) VPL-FE110U VPL-FE110M Operating Instructions  2000 Sony Corporation

expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For the customers in Canada This Class A digital apparatus complies with Canadian ICES- 003. For the customers in the United Kingdom WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code: Green-and-yellow : Earth Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol I or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Voor de klanten in Nederland • Dit apparaat bevat een Li-ion batterij voor memory back- up. • De batterij voor memory back-up van het geheugen is bevestigd op BT9001 van plaar QC. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat bij einde levensduur afdankt. • Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA. The socket-outlet should be installed near the equipment and be easily accessible. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NL

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. La prise doit être près de l’appareil et facile d’accès. Afin d’éviter tout risque d’incendie et d’électrocution, ne pas exposer l’appareil à la pluie ou à l’humidité. Pour éviter tout risque de décharge électrique, ne pas ouvrir le boîtier. Confiez l’entretien uniquement à un personnel qualifié. Para evitar riesgos de incendio o electrocución, no exponga la unidad a la lluvia ni a la humedad. Para evitar recibir descargas eléctricas, no abra el aparato. Contrate exclusivamente los servicios de personal cualificado. Per evitare il pericolo di incendi o scosse elettriche, non esporre l’apparecchio alla pioggia o all’umidità e non aprirlo. Per eventuali riparazioni, rivolgersi esclusivamente a personale qualificato. ADVERTENCIA AVVERTENZA AVERTISSEMENT ACHTUNG Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gerät abschaltet und signalisiert “Batterie leer” oder nach längerer Gebrauchsdauer der Batterien “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. Die Steckdose muß nahe bei diesem Gerät angebracht und leicht zugänglich sein. Um Feuergefahr und die Gefahr eines eiektrischen Schlages zu vermeiden, darf das Gerät weder Regen noch Feuchtigkeit ausgesetzt werden. Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur einem Fachmann. Für Kunden in Deutschland Dieses Produkt kann im kommerziellen und in begrenztem Maße auch im industriellen Bereich eingesetzt werden. Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse B besitzt. La toma mural debe estar instalada cerca del equipo y debe accederse a ésta con facilidad. La presa di corrente deve essere situata vicino all’apparecchio e deve essere facilmente accessibile.

Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE is licensed, not sold. * [Approved alternative text if Sony does not mention MS in the EULA text: “You have acquired an item (“DEVICE”) which includes software licensed by Sony from one or more software licensors (“Sony Software Suppliers”). Such software products, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties.”] • IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY CONTACT SONY FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT). • GRANT OF LICENSE. The SOFTWARE is licensed, not sold. This EULA grants you the following rights to the SOFTWARE: - You may use the SOFTWARE only on the DEVICE. - NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. SONY HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON SONY TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE. - NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS. - Note on Java Support. The SOFTWARE may contain support for programs written in Java. Java technology is not fault tolerant and is not designed, manufactured, or intended for use or resale as online control equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of Java technology could lead directly to death, personal injury, or severe physical or environmental damage. Sun Microsystems, Inc. has contractually obligated MS to make this disclaimer. - No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW, MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLARS (U.S.$250.00). - Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. - SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE. - EXPORT RESTRICTIONS. If these licensing terms are not labeled “North America Only Version” and the SOFTWARE is not identified as “North America Only Version” on the SOFTWARE packaging or other written materials, then the following terms apply: Export of the SOFTWARE from the United States is regulated by the Export Administration Regulations (EAR, 15 CFR 730- 744) of the U.S. Commerce Department, Bureau of Export Administration (BXA). You agree to comply with the EAR in the export or re-export of the SOFTWARE: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which as of May 1999 include, but are not necessarily limited to Cuba, Iran, Iraq, Libya, North Korea, Sudan, Syria, and the Federal Republic of Yugoslavia (including Serbia, but not Montenegro), or to any national of any such country, wherever located, who intends to transmit or transport the SOFTWARE back to such country; (ii) to any person or entity who you know or have reason to know will utilize the SOFTWARE or portion thereof in the design, development or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S. federal agency has suspended, revoked or denied your export privileges. For additional information see http://www.microsoft.com/exporting/. If the licensing terms are labeled “North America Only Versions” or if the SOFTWARE is labeled “North America Only Version” on the SOFTWARE packaging or other written materials, then the following applies: The SOFTWARE contains strong encryption features. The SOFTWARE may be distributed in the United States, its territories, possessions and dependencies, and Canada without an export license. Export of the SOFTWARE from the United States is regulated under “EI controls” of the Export Administration Regulations (EAR, 15 CFR 730-744) of the U.S. Commerce Department, Bureau of Export Administration (BXA). An export license or applicable license exception is required to export the SOFTWARE outside the United States or Canada. You agree that you will not directly or indirectly export or re-export the SOFTWARE (or portions thereof) to any country, other than Canada, or to any person or entity subject to U.S. export restrictions without first obtaining a Commerce Department export license or determining that there is an applicable license exception. You warrant and represent that neither the BXA nor any other U.S. federal agency has suspended, revoked, or denied your export privileges. For additional information see http://www.microsoft.com/exporting/.

Overview Precautions ........................................................................ 6 Features.............................................................................. 7 Location and Function of Controls .................................. 8 Front ........................................................................................8 Rear .......................................................................................12 Remote Commander .............................................................14 Setting up and projecting Precautions on Installation............................................. 17 Installing the Projector on the Floor .............................. 18 Connecting to LAN .......................................................... 19 Connecting with a Computer or a VCR.......................... 21 Projecting ......................................................................... 22 Adjustments and settings using the menu Using the Menu ................................................................ 25 The PICTURE CTRL Menu .............................................. 26 The INPUT SETTING Menu ............................................. 27 The SET SETTING Menu ................................................. 30 The SIGNAL SELECT Menu ............................................ 31 Connection examples/ Index number setting Connection Examples ..................................................... 32 Connecting 15k RGB/Component Equipment......................32 Connecting the Switcher .......................................................33 Confirming the System Construction....................................34 Setting the Index Numbers ............................................. 35 Maintenance Maintenance ..................................................................... 37 Replacing the Lamp ..............................................................37 Cleaning the Air Filter...........................................................38 Troubleshooting............................................................... 39 Others Specifications .................................................................. 42 Index ................................................................................. 46

identical with the voltage of your local power supply. If voltage adaptation is required, consult with qualified Sony personnel. • Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified Sony personnel before operating it further. • Unplug the unit from the wall outlet if it is not to be used for several days. • To disconnect the cord, pull it out by the plug. Never pull the cord itself. • The wall outlet should be near the unit and easily accessible. • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Do not look into the lens while the lamp is on. • Do not place your hand or objects near the ventilation holes — the air coming out is hot. On installation • When the projector is mounted on the ceiling, the Sony PSS-2000 Projector Suspension Support must be used for installation. • Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. Leave space of more than 30 cm (11 7/8 inches) between the wall and the projector. Be aware that room heat rises to the ceiling; check that the temperature near the installation location is not excessive. • Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity, mechanical vibration or shock. • Do not install the projector near to medical instruments when a LAN card is used. It may cause incorrect operations of the instruments. On illumination • To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight. • Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the contrast ratio. • Cover any windows that face the screen with opaque draperies. • It is desirable to install the projector in a room where floor and walls are not of light-reflecting material. If the floor and walls are of reflecting material, it is recommended that the carpet and wall paper be changed to a dark color. On preventing internal heat build-up After turning off the power, the cooling fan runs for about six minutes while the ON indicator flashes in green. The indicator flashes quickly for one minute. During that time, you will not be able to turn the power back on with the ON key. Caution The projector is equipped with ventilation holes (intake) at the bottom/front side and ventilation holes (exhaust) at the left/right side. Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector. On cleaning • To keep the cabinet looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents, such as thinner, benzene, or abrasive cleansers, since these will damage the cabinet. • Avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner. • Clean the air filter in every 100 hours. On repacking Save the original shipping carton and packing material; they will come in handy if you ever have to ship your unit. For maximum protection, repack your unit as it was originally packed at the factory. On LCD projector LCD projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the LCD projector. This is a normal result of the manufacturing process and does not indicate a malfunction.

• High brightness Adopting four newly developed 120 W UHP lamps and a LCD panel with micro lens provides high brightness (light output 4,000 of ANSI lumen) and excellent uniformity on the picture. • High resolution Thanks to use of three 1.8-inch SXGA1) panels with approximately 1,300,000 pixels, the projector can project the sharp picture with the resolution of 1280 × 1024 pixels. • DRC (Digital Reality Creation) The DRC technology allows you to obtain a finer, more detailed picture with four-times higher density than the conventional video picture. Accepts various input signals This projector has a built-in high performance scan converter which converts the input signals to display the 15 k RGB, DTV, HDTV, VGA1), SVGA1), XGA1), SXGA1) and UXGA1) (fV = up to 75 Hz) signals as well as the video signals of the composite, S video and component. The projector accepts a wide range of HDTV/DTV signals as shown in the chart below. System expandability and versatility The projector has RS-232C/422A/PJ COM interface connectors for communication. * Each of the frame rates is also compatible with 1/1.001. Format 1035/60i 1080/60i 480/60P 575/50P 1080/24PSF 1080/50i 720/60P 720/50P Scanning rate (kHz) 33.75 33.75 31.5 31.25 27 28.13 45 37.5 Frame rate (Hz)* 30 30 60 50 24 25 60 60 Scanning format 2:1 interlace 2:1 interlace Progressive Progressive 2:1 interlace 2:1 interlace Progressive Progressive Aspect ratio 16:9 16:9 16:9/4:3 16:9/4:3 16:9 16:9 16:9 16:9 Standard BTA S-001B SMPTE 274M/ BTA S-001B SMPTE 293M – – SMPTE 274M SMPTE 293M – .......................................................................................................................................................................................................... 1) VGA, SVGA, XGA, SXGA and UXGA are the registered trademarks of the International Business Machines Corporation, U.S.A. 2) Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. By combining the interface boards and signal interface switcher (not supplied), VPL-FE110U/FE110M projection systems can be greatly expanded. This projector also has the group and device index functions for using multiple projectors in one system. Easy and flexible setup • Easy setup with external equipment This projector has 48 preset data for input signals in the memory. You can get a picture properly on the screen by connecting equipment and pressing Sony’s original APA (Auto Pixel Alignment) key. • Flexible setup The lens shift function allows you to install the projector in a wide range of locations, without worrying about keystone distortion (the picture going out of square). The power focus and power zoom functions also let you change the size of the projection screen without having to move the projector. • Stack installation Thanks to the lens shift function, up to three projectors can be stacked, which improves the brightness of the image. • Fail safe function The projector uses four lamps for light source. Even if one of them has burnt out, you can still use the projector. If two lamps have burnt out, the projector will automatically enter into standby mode. Selectable four lamps or two lamps You can select four lamps for high brightness or two lamps for the long lamp lives. (For setting the lamp mode, consult with qualified Sony service personnel.) Convenient network function As the Microsoft2) Windows2) CE is built in the projector, you can connect the projector to LAN using an optional LAN/wireless LAN PC card.

Front q; 3 7 9 1 2 8 5 4 6 1 Speaker 2 Lens mount part When attaching the optional lens, consult with the Sony service personnel. 3 Front remote control (SIRCS) detector 4 Bottom ventilation holes (intake) Do not block the holes. 5 Adjusters Use the adjusters to keep the projector level if it is installed on an uneven surface. 6 Front ventilation holes (intake) Do not block the holes. 7 Adjuster button and lever Press the button to raise the lever for adjusting the height of the adjuster. 8 Handle lever (left and right sides) Use the lever for putting away the carrying handle. 9 Carrying handle (left and right sides) Pull out the handle for carrying the projector. 0 Left and right side ventilation holes (exhaust) Do not place anything within the 30 cm (11 7/8 inches) range from these holes or block them. Notes • Do not block the ventilation holes, or internal heat build-up may occur, causing fire or damage to the projector. • Do not place anything near the ventilation holes or touch these holes as the temperature will be very high.

Pull out to use for carrying the projector. To put away the handle, slide the handle lever forward. Using the adjusters 1 Press the adjuster button. The adjuster lever comes out. 2 Turn the lever to adjust the height so that the projector becomes level. 3 Replace the adjuster lever after use. Adjuster button To raise the projector To lower the projector

1 ON key and indicator Press to turn on the power of the projector. The indicator lights when the key is pressed. The indicator flashes for about six minutes after the power is turned off by pressing the STANDBY key, as the fan runs for six minutes to cool down the inside of the projector. The indicator flashes quickly for one minute, during which you will not be able to turn the power back on with the ON key. 2 STANDBY key and indicator Press to make the projector enter standby mode. The indicator lights to indicate that the projector is in standby mode. 3 LIGHT key Illuminates the key indicators in orange when the projector is turned on. Illuminates the indicators for the relative keys in green when this key is pressed during operation. Press again to turn off the indicators. Pressing this key and the RESET key simultaneously has the same function as the SYS SET key on the Remote Commander. Use when the PC-3000 signal interface switcher is used in the system or the system connections are changed. 4 APA (Auto Pixel Alignment) key Adjusts the position of the picture on the screen automatically so that the picture is clearly visible when the signals are input from a computer. 5 MUTING keys Cut off the picture or sound temporarily. PIC: Press to cut off the picture. Press again to restore the picture. AUDIO: Press to cut off the sound output from the speakers or the AUDIO OUT jacks. Press again or press the VOLUME + key to restore the sound. 6 VOLUME +/– keys Adjust the volume of the built-in speakers and output level of the AUDIO OUT jacks. + : Increases the volume. – : Decreases the volume.

Select the input signal. VIDEO: Selects the video signal input from the VIDEO or S VIDEO connectors and the audio signal input from the AUDIO IN L/R jacks. To switch the S VIDEO and VIDEO connectors, use the SELECT key. SELECT: Each time you press this key, the input video signal is switched between the VIDEO and S VIDEO connectors. INPUT A: Selects the audio and video signals input from the INPUT A connectors. INPUT B: Selects the signal input from the connectors on the optional interface board which is installed in the INPUT B section. When the IFB-12A interface board is installed and the output mode is selected on the IFB-12A, the key does not function. INPUT C: Selects the Windows CE. Note When the INPUT C/RS-232C/RS-422A select switch is not set to INPUT C, the image from the INPUT C slot does not appear. 8 Indicators POWER SAVING: Lights when the projector is in power saving mode. When POWER SAVING in the SET SETTING menu is set to ON, the projector goes into the power saving mode if no signal is input for 10 minutes. Although the lamp goes out, the cooling fan keeps running. In the power saving mode, only the STANDBY key functions for the first 60 seconds. The power saving mode is canceled when a signal is input or any key is pressed. COVER FAIL: Lights when the lamp cover or air filter cover is not secured firmly. FAN FAIL: Lights when the fan is broken. HIGH TEMP: Lights when temperature inside the projector becomes unusually high. LAMP FAIL: When the lamp life has reached the end, the indicator of that lamp lights. 9 Rear remote control (SIRCS) detector 0 Message display window Displays the signal status, timer and error messages about the input signals. qa PATTERN key Displays a HATCH pattern on the screen for focus, zoom, and shift adjustments. Press again to turn off the HATCH pattern. qs ZOOM key Enters the zoom adjustment mode. When the key is pressed, the relative keys light in green. Next adjust the zoom using the arrow keys. V, b: Enlarges the picture size. v, B: Reduces the picture size. Note If the VPLL-2075, VPLL-2014, VPLL-2009 or VPLL- 3050 optional lens is installed, you cannot adjust the zoom. qd FOCUS key Enters the focus adjustment mode. When the key is pressed, the relative keys light in green. Next adjust the focus using the arrow keys. V, b: Focuses on a forward picture. v, B: Focuses on a picture further back. qf SHIFT (lens shift) key Enters the shift adjustment mode. When the key is pressed, the relative keys light in green. Next adjust the vertical position of the picture using the arrow keys. V, b: Moves the picture upward. v, B: Moves the picture downward. qg ENTER key Stores the settings in the menu. qh Arrow keys (V/v/B/b) Used to adjust the picture after pressing the ZOOM, FOCUS or SHIFT key. Also used to move the cursor or adjust the value in the menu. qj MENU key Displays the menu on the screen. When the key is pressed, the relative keys light in green. Press again to turn off the menu. qk RESET key Resets the adjusted value of an item to its factory preset value. This key functions when the menu or a setting item is displayed on the screen.

IN OUT 0 0 INPUT C PC CARD INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG KEYBOARD MOUSE DEVICE INDEX + – 5 4 3 1 2 8 7 9 0 qsqd qa qf qg + 6 Location and Function of Controls 1 Control panel For details, see pages 10 and 11. 2 AUDIO OUT L/R jacks (phono type) Connect to external active speakers. The volume of the speakers can be controlled by the VOLUME keys on the Remote Commander or the control panel. 3 VIDEO connectors Connect to external video equipment, such as a VCR. Y IN/C IN (BNC type): Connect to the Y and C video outputs of the video equipment. S VIDEO IN (mini DIN 4-pin): Connects to the Y/C video output of the video equipment. S VIDEO OUT (mini DIN 4-pin): Used as loop- through output via the Y/C IN connectors or the S VIDEO IN connector. VIDEO IN (BNC type): Connects to the composite video output connector of the video equipment. VIDEO OUT (BNC type): Used as loop-through output of the VIDEO IN connector. AUDIO IN L (MONO)/R jacks (phono type): Connect to the audio output jacks of equipment, such as a VCR. For stereo equipment, use both the L and R jacks; for monaural equipment, use the L (MONO) jack only. Note If you have video equipment connected to both the Y/ C IN and S VIDEO IN connectors, the signal from the Y/C IN connectors are selected prior to the S VIDEO IN connector. When projecting video connected to the S VIDEO IN connector, be sure not to connect any cable to the Y/C IN connectors. 4 INPUT A connectors RGB input connectors (R/R-Y/PR, G/Y, B/B-Y/PB, SYNC/HD, VD) (BNC type): Connect to the video outputs of equipment such as a computer or a video camera. According to the connected equipment, the RGB, component (R-Y, Y, B-Y), HDTV (YPBPR or GBR) or DTV (YPBPR or GBR) signal is selected. AUDIO IN L (MONO)/R jacks (phono type): Connect to the audio output jacks of equipment such as a computer or a video camera. For stereo equipment, use both the L and R jacks; for monaural equipment, use the L (MONO) jack only. Note The INPUT A connectors do not function when the PC-3000 signal interface switcher is connected.

(INPUT B) Optional signal interface board can be attached according to your requirements. If you install the IFB- 12A interface board to this section and select the output mode, you can output the signal input through the INPUT A connectors. For details on installing the interface boards, consult with qualified Sony personnel. 6 PC card slot (INPUT C)(Type II) The recommended LAN PC card or memory card can be attached according to your requirements. For details, please read the attached “Operating Instructions for Networking.” Note You cannot output the signal input through the INPUT C from the INPUT B connectors (even when the IFB- 12A interface board is installed to INPUT B.) 7 INPUT C/RS-232C/RS-422A select switch Selects according to the interface connected to the INPUT C or RS-232C/RS-422A connector. 8 REMOTE connectors Used to expand system capability. RS-232C/RS-422A connector (D-sub 9-pin, female): Connect to a computer to operate the projector from the computer. PJ COM IN/OUT connectors (D-sub 9-pin, female): The connectors conform to the RS-485 standards and are used to expand system capability for Sony projectors. For details on connections, see the PJ COM protocol manual for Sony projectors. Note When the INPUT C/RS-232C/RS-422A select switch is set to INPUT C, you cannot use the PJ COM IN/ OUT connectors. 9 CONTROL S IN/OUT jacks (stereo minijack) Connect to the control S jacks of other Sony equipment. CONTROL S IN/PLUG IN POWER (DC 5 V output) jack: Connects to the CONTROL S OUT jack of the supplied Remote Commander when using as a wired Remote Commander. In this case, you do not need to install the batteries in the Remote Commander, since the power is supplied from this jack. CONTROL S OUT jack: Outputs the control S signal. Note When connecting the remote commander cable to the CONTROL S IN jack, the remote control detectors will not function. 0 TRIG (trigger output) jack (monaural minijack) The signal is transmitted from this jack to the connected equipment whether the projector is on or off. (This is not a power source for external equipment.) Approximately 12 V DC signal is output when the projector power is on. The signal is 0 volt level output when the projector power is off. qa DEVICE INDEX switch Set the device index number of the projector when using multiple projectors. You can set the numbers between “01” and “99”. It is set to “01” at the factory. You can also set the group index number in the menu for system setup. Note Do not set the device index number to “00”. If you do, the projector will be operated only with the keys on the control panel. qs KEYBOARD connector (PS/2, mini DIN 6-pin) Connect a keyboard. This connector functions when the INPUT C/RS-232C/RS-422A select switch is set to INPUT C and the INPUT C signal is selected. Note Connect the keyboard before the power of the projector is turned on. qd MOUSE connector (PS/2, mini DIN 6-pin) Connect a mouse. This connector functions when the INPUT C/RS-232C/RS-422A select switch is set to INPUT C and the INPUT C signal is selected. Note Connect the mouse before the power of the projector is turned on. qf AC IN socket Connect the supplied AC Power cord. qg Lamp cover

Commander. The keys on the Remote Commander with the same names function the same as those on the control panel of the projector. For details on control panel keys on the projector, see pages 10 and 11. 1 ON/STANDBY keys 2 MEMORY key This key does not function with this projector. 3 CENT R/B keys The keys do not function with this projector. 4 COMMAND ON/OFF key No keys except for the LIGHT button on the Remote Commander function when this switch is set to OFF. This saves battery power. 5 RGB keys Adjust the picture. APA: The key functions the same as the APA key on the control panel. DOT PHASE: Press to adjust the phase of the LCD panels and the input signals (except for 15k RGB/ video/HDTV/DTV signals). After pressing this key, adjust the position of the picture using the four arrow keys so that the clearest picture is obtained. SIZE: Enters the size adjustment mode for the input signal. Next adjust the horizontal size of the picture using the arrow keys. B: to reduce horizontal size b: to expand horizontal size SHIFT: Enters the shift adjustment mode for the input signal. Next adjust the position of the picture using the four arrow keys. The picture shifts in the direction of the arrow on the pressed key. 6 STATUS ON/OFF keys Press OFF to eliminate the on-screen display. Press ON to restore the on-screen display. Note The menus and warning messages appear even if the OFF key is pressed. SELECT VIDEO MEMORY SWITCHER INDEX PIC ON AUDIO OFF PATTERN FOCUS ZOOM SHIFT NORMAL MUTING STATUS LCD LENS CONTROL ON COMMAND OFF SIZE DOT PHASE APA SHIFT RGB R B CENT ON STANDBY MEMORY MENU VIDEO INPUT SELECT A D B C BLKG SYS SET RESET FUNCTION 1 4 2 3 5 8 6 7 9 10/0(ALL) SW NO/ OFF/GROUP SWITCHER/VIDEO MEMORY/INDEX ENTER POSITION BRIGHT CONTR PICTURE CONTROL HUE COLOR SHARP VOL VIDEO/S VIDEO LIGHT qf qd qs qa 0 9 qg qh ql qj qk wf wg wd ws wa w; 5 8 76 4 3 2 1 wh Location and Function of Controls

The light goes on each time a key is pressed. If the indicator does not light, replace the batteries. 8 LIGHT button Illuminates the key indicators when the COMMAND switch is set to ON. If the switch is set to OFF, only the COMMAND switch is illuminated. If you do not press any key on the Commander for more than 30 seconds, the key indicators turn off automatically. The indicators also turn off if you press the LIGHT button again. 9 MUTING keys 0 NORMAL key The key does not function with this projector. qa LCD LENS CONTROL keys Press one of the ZOOM, SHIFT and FOCUS keys and then the arrow keys (V or v). qs PATTERN key qd SYS SET (system set) key When the PC-3000 signal interface switcher is used in the system or the system connections are changed, press this key. Note After connecting the PC-3000 switcher and pressing the SYS SET key, the input channel is set to SW1-1 when connecting a single switcher, or to SW1-2 when connecting two or more switchers. qf INPUT SELECT keys The D key does not function with this projector. qg SWITCHER/VIDEO MEMORY/INDEX select switch Selects the function of the SWITCHER/VIDEO MEMORY/INDEX keys. SWITCHER: selects the input from the PC-3000 switcher. VIDEO MEMORY: The position does not function with this projector. INDEX: selects a projector by its index number when multiple projectors are used. qh SWITCHER/VIDEO MEMORY/INDEX keys When the SWITCHER/VIDEO MEMORY/ INDEX select switch is set to SWITCHER When the PC-3000 switcher is connected to the projector, press a number key (1 to 8) to select the input from the switcher. Number key 9 does not function. To select an input when multiple switchers are connected, press the SW NO/OFF/GROUP key. Next press the switcher number (1 to 8) and the input number (1 to 8) in sequence. Be sure to press the keys one after another within 2 seconds. e.g. To select input 4 of switcher 2, press the keys as follows: SW NO t 2 t 4. When the SWITCHER/VIDEO MEMORY/ INDEX select switch is set to INDEX Used to specify the device or group index number. qj BLKG (blanking) adjustment key Enters the blanking adjustment mode. Next, press the V/v key to select the position to be adjusted on the screen, and then adjust the position using the B/b keys. qk RESET key Press the FUNCTION key and then RESET key on the Remote Commander within 5 seconds to reset the Windows CE. ql PICTURE CONTROL +/– keys Adjust the picture conditions: CONTR (contrast), BRIGHT (brightness), COLOR, HUE and SHARP (sharpness). w; VOL (volume) +/– keys wa POSITION +/– keys These keys do not function with this projector. ws FUNCTION key Press the FUNCTION key and then RESET key on the Remote Commander within 5 seconds to reset the Windows CE. (continued)

2 Install three R6 (size AA) batteries (supplied) with the polarities correctly aligned. 3 Replace the lid. Notes on batteries • Make sure that the battery orientation is correct when inserting batteries. • Do not mix old battery with new one, or different types of batteries. • If you will not use the Remote Commander for a long time, remove the batteries to avoid damage from battery leakage. If batteries have leaked, remove them, wipe the battery compartment dry and replace the batteries with new ones. Be sure to install the battery from the # side. 0 0 INPUT C INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG DEVICE INDEX + – KEYBOARD MOUSE PC CARD Rear to CONTROL S IN Remote commander cable (supplied) Remote Commander to CONTROL S OUT Location and Function of Controls Notes on wireless Remote Commander operation • Be sure that there is nothing to obstruct the infrared beam between the Remote Commander and the projector. • The operation range is limited. The shorter the distance between the Remote Commander and the projector, the wider the angle within which the commander can control the projector. • The remote control detectors on the projector do not operate when connecting the remote commander cable to the CONTROL S IN jack. If you wish to use the Remote Commander as a wireless Remote Commander, be sure to remove the remote commander cable from both the Remote Commander and the projector. To connect the Remote Commander to the projector Note on wired Remote Commander operation using the supplied remote commander cable (stereo) You do not need to install the batteries since the power is supplied from the CONTROL S IN jack on the projector. In this case, the batteries are not consumed. wd ENTER key wf Arrow keys wg MENU key wh CONTROL S OUT jack Connect the supplied remote control cable to this jack and to the CONTROL S IN jack of the projector for wired remote control operation. When the Commander is connected to the CONTROL S IN/PLUG IN POWER jack of the projector via the remote control cable (stereo), the power for the Remote Commander is supplied from the projector.

ventilated place The projector is equipped with ventilation holes for intake on the bottom and front and ventilation holes for exhaust on the left and right sides to prevent internal heat build-up. Do not block these ventilation holes and allow adequate air circulation at an installation location. Do not place any object beside the projector If you put something beside the ventilation holes on the sides, the exhaust may be inhaled into the projector through the ventilation holes (intake) at the bottom, causing the internal temperature to rise and thereby activating the protection circuit. Install the projector so that the exhaust is not blocked. Do not install the projector in a location where temperature or humidity is very high Avoid installing the projector in a location where temperature may rise or fall rapidly Be careful of air-conditioning and heating in a room where the projector is installed, as sudden changes in temperature may lead to moisture condensation and cause damage to the projector. Precautions on Installation Do not install the projector in the following situations. These installations may cause malfunction or damage to the projector. Avoid installing the projector in a location subject to excessive dust Do not cover the ventilation holes (exhaust) Do not cover the front ventilation holes; otherwise, internal heat may build up. Do not install the projector on a deep-pile carpet If you install the projector on a deep-pile carpet, the ventilation holes (intake) at the bottom may be blocked, causing an internal heat build-up. Do not tilt the projector more than 20 degrees Avoid tilting the projector side to side more than 20 degrees or installing it other than on the floor or ceiling. Such installations may cause malfunctions such as color irregularity or shortening of lamp life. Setting up and projecting The front to back tilt angle of this projector is not limited. 20°

IN OUT 0 0 INPUT C INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG DEVICE INDEX + – R/R-Y Y C 8 VIDEO 8 VIDEO VIDEO AUDIO IN VIDEO G/Y B/B-Y SYNC /HD VD AUDIO IN L (MONO) L R L R (MONO) R RS- 232C RS- 422A RS-232C/422A RS-485 IN OUT IN OUT LIGHT APA VIDEO INPUT A INPUT B INPUT C PCI AUDIO VOLUME SELECT VIDEO/ S VIDEO INPUT SELECT RESET ENTER MENU FOCUS SHIFT ZOOM PATTERN POWER SAVING LAMP FAIL 1 2 3 4 COVER FAIL FAN FAIL HIGHT TEMP MUTING PLUG IN POWER IN OUT 0 0 INPUT C INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG DEVICE INDEX + – Installing the Projector on the Floor This section describes the installation arrangements for installing the projector on the floor. For ceiling installation, consult with qualified Sony personnel. For details on installation examples with projection distances, see the supplied “Projection Distance Charts.” Horizontal center of the screen Vertical center of the screen Installation area Projection distance Install the projector so that the tip of the lens is within this area. The distance between the lens and the screen varies depending on the size of the screen and the attached lens. Use the charts for installation examples in the supplied “Projection Distance Charts.” Adjust the vertical and horizontal positioning of the projector. Vertical positioning (side view) Screen Adjustable range You can adjust the angle of projection by performing the shift adjustment (page 24). • Install the projector so that the center of the lens is between just above the bottom edge of the screen and the center of the screen. • When using the VPLL-2009, make sure that the center of the lens is aligned with the vertical center of the screen. Horizontal positioning (top view) Screen Center of the projector 38 mm (1 1/2 inches) Center of the lens Adjust the horizontal positioning of the projector so that the center of the lens is aligned with the horizontal center of the screen.

This section describes how to connect the LAN PC card or wireless LAN PC card and install the memory card. For details on how to connect other equipment, see pages 21 and 32 to 34. Also refer to the instruction manuals of the equipment to be connected. Installing a PC card When you use the LAN PC card, wireless LAN PC card or memory card, insert the card into the PC card slot of INPUT C of the projector and set the INPUT C/RS- 232C/RS-422A select switch to INPUT C. When the PC card is inserted into the slot, the eject button pops out. To remove the PC card from the slot, press the eject button. Eject button Rear Notes • For details of the recommended PC card or wireless LAN access point, see the attached “Recommended PC card/wireless LAN access point.” • When you use LAN , you must set the IP address. For details of setting IP address, etc,. see the attached “Operating Instructions for Networking.” to the PC card slot of INPUT C PC card Insert the card with the arrow mark facing torward the slot. to router Hub LAN cable LAN PC card (NE2000 compatible) (recommended) Set to INPUT C. Mouse Keyboard Computer Computer Computer Before inserting the PC card or memory card, remove the protect card from the slot. Noise prevention core (see page 20.) PS/2 PS/2 Connection of LAN PC card

Rear to hub/router Wireless LAN PC card (IEEE802.11b conform) (recommended) Set to INPUT C. Mouse Keyboard Computer Computer Wireless LAN access point (IEEE802.11b conform) (recommended) Installing a memory card You can memorize the presentation file made by the Microsoft PowerPoint1) in the memory card and show the file by inserting the memory card into the PC card slot of the projector. For attaching and removing the memory card, see “Installing a PC card” on page 19. For details of the recommended PC card, see the attached “Recommended PC card/wireless LAN access point.” ...................................................................................................................................................................................... 1) PowerPoint is a registered trademark of Microsoft Corporation in the United States and/or other countries. Connecting to LAN When connecting the projector to LAN Attach the supplied noise prevention core near to the projector of the LAN cable. When the shielded LAN cable is used, you do not need to attach the noise prevention core. Connector for connecting to the projector LAN cable Noise prevention core PS/2 PS/2

This section describes how to connect the projector with a computer, VCR, and external active speakers. For details on how to connect other equipment, see pages 32 to 34. Also refer to the instruction manuals of the equipment to be connected. When making connections, be sure to: • turn off all equipments before making any connections. • use the proper cables for each connection. • insert the plugs of the cables properly; plugs that are not fully inserted often generate noise. When pulling out a cable, be sure to pull it out by the plug, not the cable itself. Note Set INPUT-A in the SIGNAL SELECT menu to COMPUTER. For details, see page 31. 0 0 INPUT C INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG DEVICE INDEX + – KEYBOARD MOUSE PC CARD : VCR to S VIDEO OUT to VIDEO OUT to AUDIO OUT S video cable (not supplied) Video cable (not supplied) Audio cable (not supplied) Rear to a wall outlet AC power cord (supplied) to AC IN SMF-400 Monitor cable (5BNC˜HD D-sub 15-pin) (not supplied) Use the optional ADP-20 Signal adapter (not supplied) when connecting with a Macintosh computer. Computer Audio cable (not supplied) Active speakers Signal flow Audio cable (not supplied)

The ON indicator lights in green. 2 Turn on the power of equipment connected to the projector. Press the INPUT SELECT keys on the Remote Commander or the control panel to select the input source. VIDEO: Selects the video signal input from the VIDEO or S VIDEO connectors and the audio signal input from the AUDIO IN L/R jacks. To switch the VIDEO or S VIDEO connectors, use the SELECT key. SELECT: Each time you press this key, the input signal is switched between VIDEO and S VIDEO. INPUT A: Selects the audio and video signals input from the INPUT A connectors. INPUT B: Selects the signal input from the connectors on the optional interface board which is installed in the INPUT B section. INPUT C: Selects the Windows CE. 0 0 INPUT C INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG DEVICE INDEX + – KEYBOARD MOUSE + – SELECT VIDEO MEMORY SWITCHER INDEX PIC ON AUDIO OFF PATTERN FOCUS ZOOM SHIFT NORMAL MUTING STATUS LCD LENS CONTROL ON COMMAND OFF SIZE DOT PHASE APA SHIFT RGB R B CENT ON STANDBY MEMORY MENU VIDEO INPUT SELECT A D B C BLKG SYS SET RESET PUNCTION 1 4 2 3 5 8 6 7 9 10/0(ALL) SW NO/ OFF/GBOUP SWITCHER/VIDEO MEMORY /INDEX NO ENTER POSITION BRIGHT CONTR PICTURE CONTROL HUE COLOR SHARP VOLUME VIDEO/S VIDEO LIGHT + – ON STANDBY PIC AUDIO VIDEO POWER SAVING COVER FAIL FAN FAIL LAMP FAIL 1 2 3 4 HIGHT TEMP SELECT VOLUME INPUT A INPUT B INPUT C APA MENU ENTER RESET PATTERN ZOOM SHIFT FOCUS MUTING INPUT SELECT LIGHT RESET SYS SET + Rear remote control detector STANDBY indicator ON indicator 1 4,5,6,7 7 4,6 5 2 4,6 1 4,5,6,7 7 5 3,8 3,8 2 2 2

signal interface switcher (not supplied), set the SWITCHER/VIDEO MEMORY/INDEX select switch on the Remote Commander to the SWITCHER position and press the number keys to select the input. When multiple switchers are connected, press the SW NO/OFF/ GROUP key, then press the number keys to select the input. Note Press the SYS SET key when you make the system connections using the PC-3000 switcher. 3 Press the PATTERN key on the Remote Commander or the control panel to display the HATCH pattern. 4 Press the FOCUS key then the V or v key on the Remote Commander or the control panel to adjust the focus. “FOCUS” appears on the screen during adjustment. 5 Press the ZOOM key then the V or v key on the Remote Commander or the control panel to adjust the picture size. “ZOOM” appears on the screen during adjustment. Note If the optional VPLL-2075, VPLL-2014, VPLL-2009 or VPLL-3050 lens is installed, you cannot adjust the zoom. 6 Press the FOCUS and arrow keys on the Remote Commander or the control panel to adjust the focus again. “FOCUS” appears on the screen during adjustment. (continued)

or the control panel to adjust the vertical position of the picture. “PICTURE SHIFT” appears on the screen during adjustment. 8 Press the PATTERN key again to clear the HATCH pattern. To Adjust the volume Cut off the sound Cut off the picture Note Do not look into the lens when the projector lamp is on. To turn off the power 1 Press the STANDBY key on the Remote Commander or the control panel. The ON indicator flashes in green and the cooling fan keeps running for about six minutes to reduce the internal heat. The ON indicator flashes quickly for one minute. During this time, you will not be able to turn the power back on. After about one minute, you can turn on the power with the ON key. When the fan stops running, the STANDBY indicator lights in red. Note To extend the lamp life, do not turn off the power for at least 10 minutes after turning on the power. Press the VOLUME +/– keys. the AUDIO MUTING key (also cuts off the signal output from the AUDIO OUT jacks.) To restore the sound, press the AUDIO MUTING key again or press the VOLUME + key. the PIC MUTING key. To restore the picture, press the PIC MUTING key again. Projecting

Adjustments and settings using the menu The projector is equipped with an on-screen menu for making various adjustments and settings. Unadjustable items are not displayed in the menu. To change the language used in the menu, see page 30. 1 Press the MENU key. The menu display appears. The menu presently selected is highlighted in yellow. PICTURE CTRL CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE: COLOR TEMP: 80 50 50 50 50 OFF LOW COLOR SYS: AUTO VIDEO 2 Use the V or v key to select a menu, then press the b or the ENTER key. The setting items of the selected menu are displayed. SET SETTING STATUS: SPEAKER: LANGUAGE: INSTALLATION: POWER SAVING: SIRCS RECEIVER: GROUP INDEX: DEVICE INDEX: 0 1 0 1 ON ON ENGLISH FLOOR-FRONT OFF FRONT&REAR INPUT-A 3 Use the V or v key to select the item, then press the b or the ENTER key. 4 Adjust an item. • When changing the adjustment level: To increase the number, press the V or b key. To decrease the number, press the v or B key. Press the ENTER key to restore the original screen. • When changing the setting: Press the V or v key to change the setting, then press the B or the ENTER key. The original screen is restored. For details on setting individual items, see the relevant menu pages. Menus Setting items To erase the menu display Press the MENU key. The menu display also disappears automatically if no key is pressed for one minute. To reset settings that have been adjusted Press the RESET key. “Reset complete!” appears on the screen and the settings appearing on the screen will be reset to their factory preset values. Items that can be reset are as follows: CONTRAST, BRIGHT, COLOR, HUE, SHARP, DOT PHASE, SIZE, SHIFT and BLANKING. About the memory of the settings The settings are automatically stored in the projector memory.

The PICTURE CTRL menu is used for adjusting the picture. Unadjustable items are not displayed in the menu. PICTURE CTRL CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE: COLOR TEMP: 80 50 50 50 50 OFF LOW COLOR SYS: AUTO VIDEO CONTRAST Adjusts the picture contrast. The higher the setting, the greater the contrast. The lower the setting, the lower the contrast. BRIGHT (Brightness) Adjusts the picture brightness. The higher the setting, the brighter the picture. The lower the setting, the darker the picture. COLOR Adjusts color intensity. The higher the setting, the greater the intensity. The lower the setting, the lower the intensity. HUE Adjusts the color tones. At high settings, the picture becomes greenish. At low settings, the picture becomes purplish. SHARP (Sharpness) Adjusts the picture sharpness. The higher the setting, the sharper the picture. The lower the setting, the softer the picture. D. (Dynamic) PICTURE Emphasizes the black color. ON: Emphasizes the black color to produce a bolder “dynamic” picture. OFF: Reproduces the dark portions of the picture accurately, in accordance with the source signal. COLOR TEMP (temperature) Adjusts the color temperature. HIGH: Makes the white color bluish. LOW: Makes the white color reddish. COLOR SYS (system) Selects the color system of the input signal. Normally, set to AUTO. If the picture is distorted or colorless, select the color system (NTSC3.58/PAL/SECAM/NTSC4.43/PAL-M) according to the input signal. GAMMA MODE Select either position to obtain an optimum picture. GRAPHICS: Improves the reproduction of half tones. Photos can be reproduced in natural tones. TEXT: Contrasts black and white. Suitable for images with lots of text. Input signals and adjustable/setting items Item CONTRAST BRIGHT COLOR HUE SHARP D. PICTURE COLOR TEMP COLOR SYS GAMMA MODE Y: Adjustable/can be set N: Not adjustable/cannot be set Input signal Video or S video Y Y Y Y (NTSC 3.58/ 4.431) only) Y Y Y Y N 15k RGB Y Y Y Y Y N Y N N Component/ progressive component Y Y Y Y Y Y Y N N RGB (preset) Y Y N N N N Y N Y RGB (preset) (HDTV, DTV) Y Y Y Y Y N Y N N RGB (not preset) Y Y N N N N Y N Y ........................................................................................................................................................................................................... 1) NTSC4.43 is the color system used when playing back a video recorded in NTSC color system on a NTSC4.43 system VCR.

The INPUT SETTING menu is used to change the settings of the input signal. Unadjustable items, which vary according to the input signal, are not displayed in the menu. INPUT SETTING DOT PHASE: SIZE SHIFT 8 H:1 3 4 4 H:1 2 3 V: 1 2 3 1024x768 N O . 2 3 n 2 0 INPUT-A DOT PHASE Adjusts the phase of the LCD panel and the input signal when H FILTER is set to OFF. Adjust the value to obtain the clearest picture. SIZE Adjusts the horizontal size of the picture. As the setting for H increases, the horizontal size of the picture becomes larger, and as the setting decreases, the size becomes smaller. Adjust the setting according to the input signal. Use the B or b key to adjust the horizontal size. SHIFT Adjusts the position of the picture. H adjusts the horizontal position of the picture, and V adjusts the vertical position. As the setting for H increases, the picture moves to the right, and as the setting decreases, it moves to the left. As the setting for V increases, the picture moves up, and as the setting decreases, it moves down. Use the B or b key to adjust the horizontal position and the V or v key for the vertical position. SCAN CONV (converter) Converts the signal to display the picture so that it fits the screen size. ON: Displays the picture to fill the 4:3 screen. The picture will lose some clarity. OFF: Displays the picture while matching one pixel of input picture element to that of the LCD. The picture will be clear but the picture size will be smaller. Note The function does not work for signals in Memory No. 32 and 33. ASPECT Sets the aspect ratio of the picture. When inputting 16:9 (squeezed) signal from equipment such as a DVD player, set to 16:9. 4:3: When the picture with ratio 4:3 is input 16:9: When the picture with ratio 16:9 (squeezed) is input H FILTER Corrects the vertical bands that appear on the picture. The vertical bands may occur when an RGB signal with horizontal resolution of more than 1280 × 1024 pixels is input. In such cases, set to ON. The picture will loose some clarity, but the vertical bands will be reduced. Set to OFF to associate a dot of the input signal with a pixel of the LCD. BLANKING Adjusts if excess signals are seen with the picture, or the whole picture is not seen clearly. Select BLANKING, then press the ENTER key to display the blanking adjustment screen. Use the V or v key to select the part to be adjusted (TOP, BOTOM, RIGHT or LEFT), and the B or b key to adjust.

Input signals and adjustable/setting items Item DOT PHASE SIZE SHIFT SCAN CONV ASPECT H FILTER BLANKING Y: Adjustable/can be set N: Not adjustable/cannot be set INPUT MEMORY No. The upper number indicates the memory number of the current input signal. The lower number indicates the user memory number. INPUT SETTING DOT PHASE: SIZE SHIFT 8 H:1 0 4 8 H:1 2 3 V: 1 2 3 1024x768 N O . 1 INPUT-A n 2 3 Input signal Video or S video N N Y N Y N Y (TOP and BOTTOM only) 15k RGB N N Y N Y N Y (TOP and BOTTOM only) Component/ Progressive component N Y Y N Y N Y (TOP and BOTTOM only) RGB (preset) Y (except for HDTV, DTV) Y Y Y (Only for lower resolution than SXGA) N Y (UXGA only) Y (HDTV, DTV only) RGB (not preset) Y Y Y Y (Only for lower resolution than SXGA) N Y (UXGA only) Y About the memory function The adjustment data for 48 types of input signals are preset at the factory (preset memory). When a signal is input to the projector, the signal type is automatimally detected and the data for the signal is called from the memory to display an optimum picture. The data can be adjusted in the INPUT SETTING menu and the adjusted data will be saved as user memory. When you save more than 200 user memories, the newest one always overwrites the oldest one. The saved user memory number is displayed in the INPUT SETTING menu as t NO. ss. When an RGB signal other than the preset signals is input to the projector, the memory number is displayed as 0 and the closest option is automatically selected from the preset 48 types of signals. Notes • When an RGB signal is input with sync on Green including external sync, the picture tone may be greenish. In this case, disconnect the external sync signal. • When an HDTV 1035/60i signal is input, the picture will appear smaller. Adjust SIZE, SHIFT and BLANKING referring to the following levels as a standard. SIZE H: 1479 SHIFT H: 321 V: 41 BLANKING TOP: 167 BOTTOM: 167 RIGHT: 27 LEFT: 27 • If SCAN CONV is set to ON when a signal in Memory No. 34–38 is input, the picture will appear widened. Adjust SIZE and SHIFT, referring to the following levels as a standard. Memory No. 34 35 36 37 38 SIZE 1590 1575 1590 1582 1620 SHIFT H 181 170 182 146 154 V 18 32 36 36 42 Type of input signal Memory number User memory number

75.00 60.00 H-pos V-pos 1689 40 UXGA VESA 65 81.91 65.53 H-pos V-pos 1689 41 UXGA VESA 75 93.75 75.00 H-pos V-pos 1689 43 480/60p (Progressive component) 31.47 60.00 S on G 1605 44 575/50p (Progressive component) 31.25 50.00 S on G 1616 45 1080/50i 28.13 50.00 — 1852 47 720/60p 45.00 60.00 — 1736 48 720/50p 37.50 50.00 — 2084 49 1080/24PSF 27.00 48.00 — 1929 * VESA is a registered trademark of Video Electronics Standard Association. Memory Preset signal fH fV Sync Horizontal No. (kHz) (Hz) size 1 Video 60 Hz 15.73 59.94 — — 2 Video 50 Hz 15.63 50.00 — — 3 15k RGB (60 Hz) 15.73 59.94 S on G — 4 15k RGB (50 Hz) 15.63 50.00 S on G — 5 HDTV 33.75 60.00 S on Y/G 1543 6 640 × 350 VGA-1 (VGA350) 31.47 70.09 H-pos V-neg 800 7 VESA* 85(VGA350) 37.86 85.08 H-pos V-neg 832 8 640 × 400 NEC PC98 24.82 54.42 H-neg V-neg 848 9 VGA-2 (TEXT) 31.47 70.09 H-neg V-pos 800 /VESA70 10 VESA 85 (VGA400) 37.86 85.08 H-neg V-pos 832 11 640 × 480 VGA VESA60 31.47 59.94 H-neg V-neg 800 12 Mac 13 35.00 66.67 S on G 864 13 VGA VESA 72 37.86 72.81 H-neg V-neg 832 14 VGA VESA 75 37.50 75.00 H-neg V-neg 840 (IBM M3) 15 VGA VESA 85 43.27 85.01 H-neg V-neg 832 (IBM M4) 16 800 × 600 SVGA VESA 56 35.16 56.25 H-pos V-pos 1024 17 SVGA VESA 60 37.88 60.32 H-pos V-pos 1056 18 SVGA VESA 72 48.08 72.19 H-pos V-pos 1040 19 SVGA VESA 75 46.88 75.00 H-pos V-pos 1056 (IBM M5) 20 SVGA VESA 85 53.67 85.06 H-pos V-pos 1048 21 832 × 624 Mac 16 49.72 74.55 H-neg V-neg 1152 22 1024 × 768 XGA VESA 43 35.52 86.96 H-pos V-pos 1264 (8514) 23 XGA VESA 60 48.36 60.00 H-neg V-neg 1344 24 XGA VESA 70 56.48 69.96 H-neg V-neg 1328 25 XGA VESA 75 60.02 75.03 H-pos V-pos 1312 26 XGA VESA 85 68.68 85.00 H-pos V-pos 1376 27 1152 × 864 VESA 70 64.00 70.02 H-pos V-pos 1472 28 VESA 75 67.50 75.00 H-pos V-pos 1600 29 VESA 85 77.49 85.06 H-pos V-pos 1568 30 1152 × 900 SUN LO 61.80 65.96 H-neg V-neg 1504 31 SUN HI 71.71 76.05 C-neg 1472 32 1280 × 960 VESA 60 60.00 60.00 H-pos V-pos 1800 33 VESA 75 75.00 75.00 H-pos V-pos 1728 34 1280 × 1024 SXGA VESA 43 46.43 86.87 H-pos V-pos 1696 35 SGI-5 53.32 50.06 H-neg V-neg 1680 36 SXGA VESA 60 63.97 60.01 S on G 1696 37 SXGA VESA 75 79.98 75.03 H-pos V-pos 1688 38 SXGA VESA 85 91.15 85.02 H-pos V-pos 1728

The SET SETTING menu is used for changing the initial settings of the projector. Unadjustable items are not displayed in the menu. SET SETTING SPEAKER: LANGUAGE: INSTALLATION: POWER SAVING: SIRCS RECEIVER: GROUP INDEX: DEVICE INDEX: 0 1 0 1 ON ON ENGLISH FLOOR-FRONT FRONT&REAR INPUT-A STATUS:AT OFF STATUS Sets up the on-screen display. ON: Shows all of the on-screen displays. OFF: Turns off the on-screen displays except for the menus and warning messages. SPEAKER Set to OFF to cut off the sound of the internal speaker when external speakers are connected. When set to OFF, “SPEAKER OFF” appears on the screen when you turn on the power. LANGUAGE Selects the language used in the menu and on-screen displays. Available languages are: English, French, German, Italian, Spanish, Japanese and Chinese. INSTALLATION Reverses the picture horizontally or vertically. FLOOR-FRONT: The picture is not reversed. CEILING-FRONT: The picture is reversed horizontally and vertically. FLOOR-REAR: The picture is reversed horizontally. CEILING-REAR: The picture is reversed vertically. Note In case of using a mirror, be careful of installation since the picture may be reversed. POWER SAVING When set to ON, the projector goes into the power saving mode and the lamp for light source turns off if no signal is input for about 10 minutes. The power saving mode is canceled when a signal is input or any key is pressed. SIRCS RECEIVER Selects the remote control detectors to be activated. Change the setting if the wireless Remote Commander does not work properly due to the influence of the fluorescent lamp, etc. FRONT & REAR: Activates both the front and rear detectors. FRONT: Activates the front detector only. REAR: Activates the rear detector only. OFF: Activates neither the front nor rear detector. Note When set to OFF, the wireless Remote Commander does not function. Use the keys on the control panel or the wired Remote Commander. GROUP INDEX Groups multiple projectors or switchers to operate them simultaneously. You can set the group index number to the desired number between 01 and 99. For details for setting the group index, see pages 35 and 36. DEVICE INDEX Displays the index number set with the INDEX switches on the rear of the projector. You can check the device index number but cannot set it with this menu. For details for setting the number, see page 35.

The SIGNAL SELECT Menu is used for selecting the input signal. Depending on the interface board installed in the projector, some items may not be displayed in the menu. SIGNAL SELECT INPUT-A: INPUT-B: DTV-GBR DTV-GBR INPUT-A Use the V or v key to select the input, then press the ENTER key. INPUT-A Selects audio and video signals input from the INPUT A connectors. COMPUTER: Inputs the signal from a computer or the RGB signal for a still picture. COMPONENT: Inputs the component signal. DTV-YPBPR: Inputs the DTV (YPBPR) or HDTV (YPBPR) signal. DTV-GBR: Inputs the DTV (GBR) or HDTV (GBR) signal. Note When the PC-3000 signal interface switcher is connected to the INPUT A connectors, you cannot select the item. INPUT-B Selects the input signal from the connectors on the optional IFB-12A interface board installed in the INPUT B section. COMPUTER: Inputs the signal from a computer or the RGB signal for a still picture. COMPONENT: Inputs the component signal. DTV-YPBPR: Inputs the DTV (YPBPR) or HDTV (YPBPR) signal. DTV-GBR: Inputs the DTV (GBR) or HDTV (GBR) signal. VIDEO: Inputs the composite video signal. S-VIDEO: Inputs the S video signal. Note This item is not displayed when the optional interface board other than the IFB-12A is installed in the INPUT B section, or when the output mode is selected on the IFB-12A.

Connecting 15k RGB/Component Equipment Note Switch the input signal with the INPUT-A item in the SIGNAL SELECT menu. For details, see page 31. 0 INPUT C INPUT B INPUT A VIDEO AUDIO OUT REMOTE CONTROL S TRIG DEVICE INDEX + – 1 KEYBOARD MOUSE : PC CARD For details on how to connect to LAN, see page 19. For details on how to connect a computer, VCR or external active speakers, see page 21. Also refer to the instruction manual of the equipment to be connected. When making connections, be sure to: • turn off all equipments before making any connections. • use the proper cables for each connection. • insert the plugs of the cables properly; plugs that are not fully inserted may generate noise. When pulling out a cable, be sure to pull it out from the plug, not the cable itself. Connection Examples 15k RGB/component equipment to RGB/component output Monitor cable (not supplied) Rear to a wall outlet AC power cord (supplied) to AC IN Signal flow 2 Turn to the right. 1 Align the pins with the pin holes and push in the plug into the socket.

Use the optional PC-3000 Signal Interface Switcher for connecting various video equipment. The input can be selected by pressing the SWITCHER/VIDEO MEMORY/INDEX keys on the Remote Commander. For selecting the input from the switcher, see page 15. Notes • When you select the input from the switcher, be sure to set the SWITCHER/VIDEO MEMORY/INDEX select switch to the SWITCHER position. • When connecting the switcher, use the wired Remote Commander. If you use the wireless Remote Commander, it activates the remote control detector on only one unit of the equipment connected through the PJ COM connector. For the other equipment, set SIRCS RECEIVER in the SET SETTING menu to OFF to deactivate the remote control detectors. For details, see page 30. • After all the connections are completed, attach the terminator (supplied) to the PJ COM connector on both the projector and switcher to which nothing is connected. Device index number: 01 Rear to INPUT A SIC-10 connecting cable (5BNC y 5BNC) (not supplied) to OUTPUT PC-3000 switcher Computer, etc. to PJ COM IN RCC-5G/10G/30G connecting cable (not supplied) to PJ COM OUT Attach the supplied terminator. to the wall outlet AC power cord (supplied) to AC IN Signal flow VCR, etc. Attach the terminator (supplied with the PC-3000). Connection examples/Index number setting Set to RS-232C or RS-422A.

After all the connections are complete, confirm that equipment of the system is properly setup. 1 Connect the AC cords of all equipment to the AC outlets. 2 Press the SYS SET key on the Remote Commander. You can also press the LIGHT and RESET keys simultaneously on the control panel for the same effect. Information on the system construction and the settings of the interface boards, etc. are automatically confirmed. Then the message disappears. Note When you want to use the projector without connecting the switcher after using the switcher in the system connections, it is necessary to confirm the system construction again by pressing the SYS SET key or the LIGHT and RESET keys after all the connections are completed. If you press the key(s), “Master Switcher not exist” appears, but the system construction is automatically recognized. When a system error is detected The following messages are displayed on the screen and display window: Message Master Switcher not exist. Same DEVICE INDEX for Projector detected. Same DEVICE INDEX for Switcher detected. Remedy Set the switcher that outputs the signal to the projector to number 1. Change either number of the projectors that have the same number. Change either number of the switchers that have the same number. Note If the switcher is in standby mode, the message appears only in the message display window. Connection Examples

0 1 Ten’s digit Unit’s digit When you connect multiple projectors in your system, you have to set the group index and device index numbers for each projector. To set the group index number If you set the same group index number for multiple projectors, you can operate multiple projectors and switchers simultaneously (such as input selection) by designating the number. The group index number can be set in the menu. For group index number setting, see page 30. To set the device index number If you set the device index number, you can control each projector individually with the supplied Remote Commander. The device index number can be set with the DEVICE INDEX switches on the rear of the projector. It is set to “01” at the factory. If only one projector is connected, set it to “01.” Notes • Do not set the same device index number for the projectors in the same system. • Do not set the number to “00.” If you do, the projector will be operated only with the keys on the control panel. It cannot be controlled with the wired or wireless Remote Commander, or with an external equipment to which the PJ COM connectors are connected. Set the same group index number. Set the different group index number for two systems. Set the same group index number. Set this switcher to 1. PC-3000 PC-3000 Projector PC-3000 Projector Projector Signal flow Signal flow Signal flow PJ COM Signal flow PJ COM PJ COM PJ COM PC-3000 PC-3000 Projector Notes on setting of the index number • Set the same group index number for all equipment of the same system connection (those on the signal route between the signal source and the projector). For setting the group index number, see “GROUP INDEX” on page 30. • Set the correct group and device index numbers and the switcher number. Do not set the same device index number or the same switcher number in one group. For example, if there are different pieces of equipment with the switcher number 1, the error message will appear when the SYS SET key is pressed. • Set the switcher that outputs the signal to the projector to number 1.

switchers are used • Mount the IFB-12A interface board to the slot 1 of the number n switcher and connect the output connector of the number (n+1) switcher to the IFB-12A. • You can attach the IFB-12A signal interface board (when the IN/OUT switch is set to OUT) only to the number 1 switcher. To select the projector by designating the index numbers When the switchers and projectors are connected as illustrated, select the desired projector by pressing the keys on the Remote Commander as shown below. Number 2 switcher Device index 01 Group index 01 PC-3000 PC-3000 Projector A Projector B PJ COM PJ COM PJ COM PJ COM Signal flow Signal flow Signal flow Number 1 switcher Device index 02 Setting the Index Numbers Example: To select all the projectors GROUP t ALL t ENTER t ALL t ENTER Projectors A, B, C and D are selected. To select projectors with device index 01 from all the groups GROUP t ALL t ENTER t 1 t ENTER Projectors A and C are selected. To select a projector with device index 01 from group index 02 GROUP t 2 t ENTER t 1 t ENTER Projector C is selected. To select all the projectors from group index 02 GROUP t 2 t ENTER t ALL t ENTER Projectors C and D are selected. Notes • Set the group index and device index numbers correctly. If more than two projectors are set to the same group index and device index numbers, an error message will be displayed when the SYS SET key is pressed. • If the group index is a tens digit number, press the GROUP key before each press of the number key. Example: To select a projector with device index 13 of group index 12 GROUP t 1 t GROUP t 2 t ENTER t 1 t 3 t ENTER Group index 02 PC-3000 PC-3000 Projector C Projector D PJ COM PJ COM PJ COM Signal flow Signal flow Signal flow Number 2 switcher Device index 01 Number 1 switcher Device index 02

When the lamp has burnt out, the LAMP FAIL indicators at the rear of the projector light. In this case, replace the lamp with a new LMP-Q130 Projector Lamp (not supplied). Note Immediately after turning off the power, the lamp is extremely hot. Wait at least one hour before changing the lamp to give it enough time to cool down. To remove the lamp 1 Press the STANDBY key to set the projector to standby mode, and unplug the power cord. 2 Remove the two screws with a coin or similar object, or a screwdriver, to open the lamp cover. 3 Loosen the two screws that fasten the lamp. 4 Fold out the levers up and down. Maintenance 5 Pull out the lamp by holding the handles. To install a new lamp 1 Mount the lamp with the grooves on the top and bottom aligned with the guides on the projector. 2 Push the lamp completely until it clicks. Fold down the levers to fix the lamp to the projector. 3 Tighten the two screws to secure the lamp. (continued) Maintenance

screws to fix the cover. To reset the use time of the lamps in the message display window 1 Plug in the power cord and set the projector to standby mode. 2 Press the LIGHT, B, b and ENTER keys on the control panel in sequence. Press each key within 5 seconds. 3 Press the V, v, B or b key to display ALL. 4 Press the ENTER key. 5 Press the ENTER key again to reset the time. 6 To exit the reset mode, display EXIT and press the ENTER key. TIMER RESET? LAMP: 1 TIMER RESET? LAMP: ALL TIMER RESET?? LAMP: ALL Cleaning the Air Filter The air filter should be cleaned in every 100 hours. When it becomes difficult to remove the dust from the filter, replace the filter with a new one. 1 Turn off the power of the projector and unplug the power cord. 2 Remove the air filter cover on the bottom of the projector. 3 Remove the air filter. 4 Remove the dust from the filter with a vacuum cleaner. 5 Attach the air filter and replace the cover. Notes • If the air filter is excessively dirty, wash it with mild detergent solution and dry it in a shaded place. • Be sure to attach the air filter cover firmly; the power will not be turned on if it is not closed securely. Maintenance

correct the problem, using the following guide. If the problem still persists, consult with qualified Sony personnel. Symptom The power is not turned on. No picture and no sound. No picture or no sound. The picture is noisy. The picture from INPUT A/B connector is colored strange. “Please check INPUT-A in SIGNAL SELECT” appears in spite of inputting the correct signal from INPUT A. “Please check INPUT-B in SIGNAL SELECT” appears in spite of inputting the correct signal from INPUT B. “NO INPUT” appears when 15k RGB or component signal is input. On-screen displays do not appear. Color balance is not correct. The picture is too dark. The picture is not clear. The image from INPUT C is fixed. Cause The power has been turned off and on with the ON key at a short interval. The lamp cover is detached. The air filter cover is detached. Cable is disconnected. Input selection is not correct. Either the picture or the sound is cut off. Noise may appear on the background depending on the combination of the numbers of dot input from the connector and numbers of pixel on the LCD panel. Setting for INPUT-A or INPUT-B in the SIGNAL SELECT menu is incorrect. Setting for INPUT-A in the SIGNAL SELECT menu is incorrect. Setting for INPUT-B in the SIGNAL SELECT menu is incorrect. The sync signal is incorrect. STATUS in the SET SETTING menu is set to OFF. Picture has not been adjusted properly. The color system of the input signal is not set correctly. The lamp is nearing the end of its life. Contrast or brightness has not been adjusted properly. The picture is out of focus. Moisture condensation has occurred on the lens. Some trouble has occurred to the Windows CE. Troubleshooting Remedy Wait for about one minute before turning on the power (see page 10). Attach the lamp cover securely. Attach the air filter cover securely (see page 38). Check that the proper connections have been made (see pages 21, 32 and 33). Select the input source correctly in the SIGNAL SELECT menu (see page 31). Press the MUTING key to cancel the muting function (see page 24). Change the desktop pattern on the connected computer. Set INPUT-A or INPUT-B in the SIGNAL SELECT menu correctly according to the input signal (see page 31). Set INPUT-A in the SIGNAL SELECT menu correctly according to the input signal (see page 31). Set INPUT-B in the SIGNAL SELECT menu correctly according to the input signal (see page 31). Input the correct sync singal (composite sync or sync on G singal (sync on Y for component singal)). Set STATUS in the SET SETTING menu to ON (see page 30). Adjust the picture (see page 26). Set COLOR SYS in the PICTURE CTRL menu to match the color system of the input signal (see page 26). Replace the lamp with a new one (see page 37). Adjust CONTRAST or BRIGHT in the PICTURE CTRL menu properly (see page 26). Adjust the focus (see page 23). Leave the projector for about two hours with the power on (see page 17). Press the FUNCTION key and then RESET key on the Remote Commander within 5 seconds to reset the Windows CE.

appear. “NO INPUT” is displayed. The PJ COM connectors do not function. The mouse or keyboard does not function. The Remote Commander does not work. The wireless Remote Commander does not function. INPUT A cannot be selected. The COVER FAIL indicator lights. The LAMP FAIL indicator lights. The FAN indicator lights. The HIGH TEMP indicator lights. When you press the ZOOM, SHIFT or FOCUS key, “LENS CONTROL is locked! Do you wish to unlock ?” appears. Cause The INPUT C/RS-232C/RS-422A select switch is not set correctly. The INPUT C/RS-232C/RS-422A select switch is set to INPUT C. The mouse or keyboard is connected after the power of the projector is turned on. The batteries are exhausted. The remote commander cable is connected to the Remote Commander although you are using it as a wireless Remote Commander. The fluorescent lamp influences on the Remote Commander detector. You have selected a wrong index number. You have set the index number to “00”. The SIRCS RECEIVER setting is not correct. The switcher is not connected, but is recognized to be connected. The lamp cover or air filter cover is detached. The lamp with the same number of the indicator has reached the end of its life. The fan is broken. The internal temperature is unusually high. The lens control function is locked. Remedy Set the INPUT C/RS-232C/RS-422A select switch to INPUT C. Set the INPUT C/RS-232C/RS-422A select switch to RS-232C or RS-422A. Connect the mouse or keyboard before the power of the projector is turned on. You can use the mouse or keyboard when the INPUT C/RS-232C/RS-422A select switch is set to INPUT C and the INPUT C signal is selected. Replace the batteries with new ones (see page 16). Disconnect the remote control cable. Change the setting of SIRCS RECEIVER in the SET SETTING menu (see page 30). Select the correct index number (see pages 30 and 35). Select the correct index number (see pages 30 and 35). Change the setting of SIRCS RECEIVER in the SET SETTING menu (see page 30). If the PJ COM connector is connected to something other than the terminator, remove it then press the SYS SET key, or LIGHT and RESET keys on the control panel. Attach the lamp cover or air filter cover securely (see pages 37 and 38). Replace the lamp (see page 37). Consult with qualified Sony personnel. Check to see if nothing is blocking the ventilation holes. Clean the air filter. Consult with qualified Sony service personnel. Troubleshooting

screen. Message High Temperature! Power off in 1 min. Frequency is out of range! Please check INPUT-A in SIGNAL SELECT. Please check INPUT-B in SIGNAL SELECT. Backup Battery Very Low Meaning Internal temperature becomes too high. The frequency of the input signal is out of the acceptable range. You have input the RGB signal from the computer when INPUT-A in the SIGNAL SELECT menu is set to COMPONENT, DTV-GBR or DTV-YPBPR. You have input the RGB signal from the computer when INPUT-B in the SIGNAL SELECT menu is set to COMPONENT, VIDEO, S-VIDEO, DTV-GBR or DTV- YPBPR. The backup battery is worn out. Remedy Turn off the power. (If not, the power is automatically turned off about one minute later.) Check to see if nothing is blocking the ventilation holes. Clean the air filter Input a signal that is within the range of the frequency. Set INPUT-A correctly. Set INPUT-B correctly. Consult with qualified Sony service personnel.

color optical shutter system LCD panel 1.8-inch SXGA LCD panel, 3,932,160 pixels (1,310,720 pixels × 3) Lens Option Light output ANSI lumen1) 4,000 lm Lamp 120 W UHP × 4 Electrical characteristics Color system NTSC3.58/PAL/SECAM/NTSC4.43/ PAL-M system, switched automatically Resolution 600 horizontal TV lines (video input) 1280 × 1024 dots (RGB input) Acceptable computer signal fH: 15 to 100 kHz fV: 40 to 120 Hz Speakers Max. 5 W, 90 × 50 mm (3 5/8 × 2 inches), monaural Network OS Windows CE 2.12 Input/Output CONTROL S IN/PLUG IN POWER: Stereo minijack, 5 Vp-p, plug in power, DC 5 V, maximum output 60 mA OUT: Stereo minijack, 5 Vp-p REMOTE RS-232C/422A D-sub 9-pin (female) (For details, see “Pin assignment” on page 45.) PJ COM IN: D-sub 9-pin (male) OUT: D-sub 9-pin (female) (For details, see “Pin assignment” on page 45.) TRIG Minijack Power on: DC 12 V, output impedance: 4.7 kilohms Power off: 0 V S VIDEO (priority to Y IN/C IN) IN: Mini DIN 4-pin type (male) Y (luminance): 1 Vp-p ± 2 dB sync negative, 75 ohms terminated C (chrominance): Burst 0.286 Vp-p ± 2 dB (NTSC), 75 ohms terminated Burst 0.3 Vp-p ± 2 dB (PAL), 75 ohms terminated OUT: Loop-through mini DIN 4- pin type (male) Loop-through output from the S VIDEO IN connector Y IN: BNC type 1 Vp-p ± 2 dB sync negative, 75 ohms terminated C IN: BNC type Burst 0.286 Vp-p ± 2 dB (NTSC), 75 ohms terminated Burst 0.3 Vp-p ± 2 dB (PAL), 75 ohms terminated VIDEO IN: BNC type Composite video, 1 Vp-p ± 2 dB sync negative, 75 ohms terminated OUT: Loop-through BNC type Loop-through output from the VIDEO IN connector AUDIO IN Phono type (stereo) 500 mVrms, impedance more than 47 kilohms INPUT A Analog RGB/component: BNC type R/R-Y: 0.7 Vp-p ± 2 dB positive, 75 ohms terminated G: 0.7 Vp-p ± 2 dB positive, 75 ohms terminated G with sync/Y: 1 Vp-p ± 2 dB sync negative, 75 ohms terminated B/B-Y: 0.7 Vp-p ± 2 dB positive, 75 ohms terminated SYNC/HD: Composite sync: 0.6–8 Vp-p, high impedance, sync positive/negative Horizontal sync: 0.6–8 Vp-p, high impedance, sync positive/ negative ........................................................................................................................................................................................................... 1) ANSI lumen is a measuring method of American National Standard IT 7.228.

high impedance, sync positive/ negative AUDIO IN: Phono type (stereo) 500 m Vrms, impedance more than 47 kilohms HDTV/DTV (YPBPR): BNC type Y: 1 Vp-p ± 2dB positive, 75 ohms terminated Tri-level sync: ± 0.3 Vp-p Bi-level sync: 0.3 Vp-p PB/PR: 0.35 Vp-p ± 2dB positive, 75 ohms terminated HDTV/DTV (GBR): BNC type G with sync: 1 Vp-p ± 2 dB, 75 ohms terminated Tri-level sync: ± 0.3 Vp-p Bi-level sync: 0.3 Vp-p B/R: 0.7 Vp-p ± 2dB positive, 75 ohms terminated (For HDTV/DTV signals see “Acceptable HDTV/DTV signals” on page 45.) Input C PC card slot Type II AUDIO OUT (variable out) Phono type, Max. 1 Vrms When input is 500 mVrms: impedance less than 5 kilohms MOUSE Mini DIN 6-pin (female) (For details, see “Pin assignment” on page 45.) KEYBOARD Mini DIN 6-pin (female) (For details, see “Pin assignment” on page 45.) Safety regulations VPL-FE110U: UL1950, c-UL1950, FCC Class A, IC Class A VPL-FE110M: EN60 950 (NEMKO), CE, C-Tick General Dimensions 562 × 237 × 649 mm (22 1/4 × 9 3/8 × 25 5/8 inches) (w/h/d) Mass Approx. 34.5 kg (76 lb 1 oz) (excluding the optional lens) Power requirements VPL-FE110U: AC 100 to 120 V/ 220 to 240 V, 50/60 Hz1) VPL-FE110M: AC 220 to 240 V, 50/60 Hz Power consumption Approx. 830 W Standby mode: 6.8W for VPL- FE110U, 12 W for VPL-FE110M (with the INPUT C/RS-232C/RS- 422A set to INPUT C: 13.3 W for VPL-FE110U, 21 W for VPL- FE110M) Heat dissipation 2833 BTU Operating temperature 0°C to 40°C (32°F to 104°F) Operating humidity 35% to 85% (no condensation) Storage temperature –20°C to +60°C (–4°F to +140°F) Storage humidity 10% to 90% Supplied Accessories Remote Commander RM-PJ1001 (1) Size AA (R6) batteries (3) Remote commander cable (stereo) (15 m) (1) AC power cord (1) Terminator for the PJ COM connector (1) Lens ring (1) Noise prevention core (1) Operating Instructions (1) Operating Instructions for Networking (1) Installation Manual for Dealers (1) Protection Distance Chart (1) Recommended PC card/wireless LAN access point (1) CD-ROM Manual (1) Warranty Booklet (1) This projector is designed for business use. Design and specifications are subject to change without notice. (continued) ........................................................................................................................................................................................................... 1) UL listed for 120 V operation. Others

Projector Lamp LMP-S120 (for replacement) Interface Board IFB-12A (Analog RGB/component/HDTV/ composite video/S video input with 5BNC type connectors) IFB-21 (Analog RGB input/output with HD D-sub 15-pin type connector) IFB-50 (serial digital video input/output with BNC type connector) IFB-1000 (Composite video input with BNC type connector/S video input with mini DIN 4-pin type connector) Signal Interface Switcher PC-3000 Interface Unit IFU-1271/1271M SIC Cable SIC-10 9-pin remote cable (for PJ COM) RCC-5G/10G/30G Monitor Cable SMF-400 (HD D-sub 15-pin (male) y 5BNC (female)) SMF-410 (HD D-sub 15-pin (male) y HD D-sub 15-pin (female)) Signal Adapter ADP-20 (Macintosh y VGA) Remote Commander RM-PJ3000S Remote Commander RM-PJM610 Remote Control Receiver RM-PJ10 Projection Lens Fixed short focus lens VPLL-2009 Fixed short focus lens VPLL-2014 1.3-times zoom standard focus lens VPLL-Z3020 1.6-times zoom long focus lens VPLL-Z2025 1.5-times zoom long focus lens VPLL-Z2039 Fixed long focus lens VPLL-3050 Fixed long focus lens VPLL-2075 1.3-times zoom standard focus lens VPLL-Z2019 Projector Stand SU-PJ2000 (for stacking) Projector Suspension Support PSS-2000 Screens VPS-100FH (100-inch, flat) VPS-120FH (120-inch, flat) Some of the items may not be available in some areas. For details, please consult your nearest Sony office. Specifications

1 GND Ground 6 GND Ground 2 BUSY Busy 7 Busy 3 TX/RX 8 TX/RX 4 GND Ground 9 GND Ground 5 NC 1 2 3 4 5 6 7 8 9 S VIDEO connector (mini DIN 4-pin) Chrominance Luminance Tramsmit/ Receive Tramsmit/ Receive BUSY 1 2 3 4 5 6 7 8 9 Pin assignment RS-232C/422A connector (D-sub 9-pin, female) RS-232C 1 NC 6 DSR* Data Set Ready 2 RD Receive Data 7 RTS** Request to Send 3 TD Transmit Data 8 CTS** Clear to Send 4 DTR* Data Terminal 9 NC Ready 5 GND Ground * Circuit between pins 4 and 6 is short-circuited in the projector. ** Circuit between pins 7 and 8 is short-circuited in the projector. GND GND Acceptable HDTV/DTV formats * Each of the frame rates is also compatible with 1/1.001. Format 1035/60i 1080/60i 480/60P 575/50P 1080/24PSF 1080/50i 720/60P 720/50P Scanning rate (kHz) 33.75 33.75 31.5 31.25 27 28.13 45 37.5 Frame rate (Hz)* 30 30 60 50 24 25 60 60 Scanning format 2:1 interlace 2:1 interlace Progressive Progressive 2:1 interlace 2:1 interlace Progressive Progressive Aspect ratio 16:9 16:9 16:9/4:3 16:9/4:3 16:9 16:9 16:9 16:9 Standard BTA S-001B SMPTE 274M/ BTA S-001B SMPTE 293M – – SMPTE 274M SMPTE 293M – KEYBOARD/MOUSE connectors (mini DIN 6- pin) 1 DATA 2 NC 3 GND 4 +5V 5 CLOCK 6 NC 3 1 2 5 6 4

zoom 23 Air filter 38 ASPECT 27 AUDIO MUTING 24 B Battery Installation 16 notes 16 BLANKING 27 BNC connector 32 BRIGHT 26 C Carrying handles 9 Caution messages 40 COLOR 26 COLOR SYS (System) 26 COLOR TEMP 26 Connecting to LAN 19 Connections active speakers 21 BNC connector 32 computer 21 15k RGB/component equipment 32 LAN 19 Remote Commander 16 switcher 33 VCR 21 CONTRAST 26 Cut off the picture 24 the sound 24 D, E D. (Dynamic) PICTURE 26 Device index 30, 35 DOT PHASE 27 DRC (Digital Reality Creation) 7 F fH (Horizontal frequency) 29 FOCUS 23 fV (Vertical frequency) 29 Index G GAMMA MODE 26 Group index 30, 35 H Handle lever 9 H FILTER 27 HUE 26 I, J, K INPUT-A 31 INPUT-B 31 INPUT MEMORY No. 28 INPUT SETTING menu 27 Input signal selection 22 Installation on a floor 18 L Lamp replacement 37 LANGUAGE 30 Location and function of controls control panel 10 front 8 rear 12 Remote Commander 14 M, N Memory card 20 Menu Clearing the menu display 25 INPUT SETTING menu 27 PICTURE CTRL menu 26 SET SETTING menu 30 SIGNAL SELECT menu 31 Using the menu 25 Moisture condensation 17 O On-screen display 30 On-screen messages 40 Optional accessories 42 P, Q PC-3000 Signal Interface Switcher 33 PC card 19 PIC MUTING 24 PICTURE CTRL menu 26 PICTURE SHIFT 24 Pin assignment 43 PJ COM connector 33 Power turn off 24 turn on 22 POWER SAVING 30 Precautions 6 Precautions on installation 17 Projecting 22 R Remote Commander battery installation 16 connecting to the projector 16 location and function of controls 14 notes 16 Remote control (SIRCS) detector front 8 rear 11 Reset resetting the item 25 resetting the Windows CE 15 RS-232C/422A connector 13 S SCAN CONV 27 SET SETTING menu 30 SHARP 26 SHIFT 27 SIGNAL SELECT menu 31 SIRCS RECEIVER 30 SIZE 27 Slot 19 SPEAKER 30 Specifications 41 STATUS 30 Supplied accessories 42 T, U, V, W, X, Y Troubleshooting 39 Z ZOOM 23

WESTTEK, LLC. The SONY VPL-Series projector contains materials owned by Sony and Sony suppliers, including WESTTEK, LLC. Your purchase of the SONY VPL-Series projector gives you a limited right to use these materials, solely as a part of the SONY VPL-Series projector and only as necessary to use the SONY VPL Series projector in the manner described in the accompanying documentation. Your purchase of the SONY VPL-Series projector does not transfer any ownership in these materials to you and you are forbidden to use them for any purpose other than as part of the SONY VPL-Series projector. These materials are protected by copyright law and international treaties any unauthorized use, reproduction or distribution of such materials, or any portion of them, may result in severe civil and criminal penalties, and will be prosecuted to the maximum extent permissible under law.