Proline CR75PB Operating Instructions Manual

RADIO-REVEIL AVEC PROJECTION DE L’HEURE PROJECTIE WEKKERRADIO RADIO SVEGLIA CON PROIEZIONE D’ORA PROMÍTACÍ BUDÍK S RÁDIEM RÁDIOBUDÍK S PROJEKCIOU RADIO RELOJ ALARMA DE PROYECCIÓN RÁDIO, RELÓGIO, ALARME E PROJECÇÃO CR75PB OPERATING INSTRUCTIONS MANUEL D’UTILISATION HANDLEIDING ISTRUZIONI OPERATIVE POKYNY K OBSLUZE NÀVOD K OBSLUZE INSTRUCCIONES DE FUNCIONAMIENTO INSTRUÇÕES DE FUNCIONAMENTO F NL GB I CZ SK E P Downloaded from www.vandenborre.be

For your safety please read the following information This appliance must be connected to a 230-240 volts 50 cycle AC supply by means of a three pin socket, and should be protected by a 3 amp fuse. Any other supply may cause permanent damage, injury or an electrical hazard. The appliance is supplied with a standard 13 amp 3 pin plug fitted with a 3 amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 3 amp and approved to BS1362. If the mains plug is unsuitable for the socket outlet in your home or is removed for any other reason, then the cut off plug should be disposed of safely to prevent the hazard of electric shock. There is a danger of electric shock if the cut off plug is inserted into any 13 amp socket outlet. How to wire a 13 amp plug. Important The wires in the mains lead on this appliance are coloured in accordance with the following code: Blue � Neutral Brown � Live As the colours may not correspond with the markings identifying the terminals in your plug proceed as follows. The blue wire must be connected to the terminal marked N or coloured black. The brown wire must be connected to the terminal marked L or coloured red. No wire must be connected to the terminal in the plug which is marked with the letter E or with the earth symbol or coloured green and yellow. WARNINGS This appliance is intended for domestic household use only and should not be used for any other purpose or in any other application, such as for non-domestic use or in a commercial environment. Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. No naked flame sources, such as lighted candles, should be placed on the apparatus. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Ventilation Allow at least a 10 cm gap all around the product. This apparatus is not suitable for use in a tropical climate. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. To protect the environment, use local recycling facilities for battery disposal. SYMBOLS This equipment is double insulated and an earth connection is not required. This mark is applied to show the equipment conforms to European safety and electro-magnetic compatibility standards. Downloaded from www.vandenborre.be

1. Object and liquid entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 2. Water and moisture - The appliance should not be used near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. 3. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. 4. No naked flame sources, such as lighted candles, should be placed on the apparatus. 5. It shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. 6. Do not place the product in closed bookcases or racks without proper ventilation. 7. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Precautions: Please ensure that you read and follow the handling and safety precautions of this guide before attempting to use the projector clock. Place this Magic Clock out of the reach of children and infants. Do not attempt to disassemble or alter any part of the equipment that is not expressly described in this guide. Disassembly or alteration may result in high-voltage electrical shock. Internal inspections, alterations and repairs should be conducted by qualified service personnel only. Never touch internal portions of the equipment which become exposed as a result of damage. There is a risk of high-voltage electrical shock. Return it to the retail store from where you purchased it. Do not allow the equipment to come into contact with, or become immersed in water or other liquids. Do not use substances containing alcohol, benzene, thinners or other flammable substances to clean or maintain the equipment. Do not handle the power cord if your hands are wet. Use of power sources, or batteries not expressly recommended for this equipment may lead to overheating, malfunction of the equipment, fire, electrical shock or other hazards. Use only the recommended power source. Do not place a naked flame source near or on this product. Do not attempt to disassemble, alter or apply heat to the batteries. Avoid using, placing or storing the equipment in places subject to strong sunlight or high temperatures. Exposure to intense sunlight and heat may cause the batteries Downloaded from www.vandenborre.be

temperatures may also cause deformation of the casing. Do not store the equipment in humid or dusty area. Never place the projector clock close to electric motors or other equipment generating strong electromagnetic fields. Exposure to strong magnetic fields may cause malfunctions or corrupt image. Do not place projector clock on places sensitive to vibrations or table edges. Do not look directly into the projector lens as doing this may permanently damage your sight. LOCATION OF CONTROLS 1. LED Digital Clock Display 2. Volume Control – Buzz On / Off 3. Tuning Control 4. Waveband Selector 5. Snooze Control 6. Alarm Set Button 7. Time Set Button 8. Sleep Set Button 9. Minute Set Button 10. Hour Set Button 11. Power Selector 12. FM Antenna (located on back) 13. Auto Indicator 14. Battery Door (located on the base ) 15. POWER Cord (located on back ) 16. Projection On/Off Selector switch (on left hand side ) 17. Projection Case 18. Projection Lens 19. T Button 20. Focus Thumbwheel 21. M Button 22. H Button                    Downloaded from www.vandenborre.be

NOTE: There are two separate clocks in this product. 1. Set the Power Selector (11) to�OFF�. Connect the mains lead to the power supply. The base clock display will flash on and off indicating a power interruption and that the displayed time is incorrect. Please note, the projection clock does not flash after a power interruption! 2. To set the correct time, press and hold the Time Set Button (7) then press the Hour Set Button (10), or Minute Set Button (9), together, until the correct time is displayed. (Release all buttons) 3. Open the clock Battery Door (14) on the under side of the unit and insert a 6LR61 (or equivalent) 9-volt battery. The purpose of this battery is to store the information relating to alarm time and to keep the clock functioning in the event of disconnection from the mains supply or power interruption. Should this occur, the clock would continue to keep time, but the display will not illuminate. PLEASE NOTE: When operating from battery, the clock will only remain accurate for a short period of time. It is important that the mains supply is restored as soon as possible. ALARM TIME SETTING 1. Press and hold the Alarm Set Button (6) and repeatedly press the Hour Set Button (10) then the Minute Set Button (9) as appropriate until the required alarm time is displayed. (release all buttons) 2. To double check the alarm time, simply press the Alarm Set Button (6) then the display will show the pre-set alarm time. RADIO OPERATION For AM reception this unit uses an internal directional aerial, rotate the unit for best reception. For FM reception, the wire FM Antenna (12) on the back of the unit should be fully unwound. 1. Set the Power Selector (11) to the �ON� position. 2. Set the Waveband Selector (4) to the required waveband. (AM or FM ) 3. Use the Tuning Control (3) to select the desired station. 4. Adjust the Volume Control (2) to the desired listening level. 5. To turn off the radio, set the Power Selector (11) to�OFF�. If the radio does not switch off this may be caused by inadvertent operation of the Sleep Set Button (8). To cancel this, press the Snooze Button (5) once. WAKE TO RADIO Having selected your desired station and adjusted the desired listening level proceed as follows: - 1. Follow the instructions for �ALARM TIME SETTING� above. 2. When the desired alarm time has been set, set the Power Selector (11) on the �AUTO� position. Downloaded from www.vandenborre.be

4. The alarm can be temporarily stopped for 9 minutes by pressing the Snooze Button (5) once. This can be repeated up to 5 times. 5. The alarm will switch off automatically after 1 hour 59 minutes or can be cancelled by switching the Function Selector (11) to the �OFF� position. 6. The alarm will activate again after 24 hours unless the Function Selector (11) is set to �OFF�. WAKE TO ALARM 1. Follow the instructions for �ALARM TIME SETTING� above. 2. When the desired alarm time has been selected, set the Function Selector (11) to the �AUTO position. 3. Turn the Volume Control set (2) fully clockwise to select the BUZZ function. (When you hear a �CLICK� the function is active.) 4. The alarm tone will switch on automatically at the pre-set alarm time. 5. The alarm can be temporarily stopped for 9 minutes by pressing the Snooze Button (5) once. This can be repeated up to 5 times. 6. The alarm will switch off automatically after 1 hour 59 minutes or can be cancelled by switching the Power Selector (11) to the �OFF� position. 7. The alarm will activate again after 24 hours unless the Function Selector (11) is set to �OFF�. SLEEP TO RADIO The radio can be set to switch off automatically after a period of time from 1 minute to 1 hour and 59 minutes, by following this procedure:- With all the controls pre-set in the �WAKE TO RADIO�, or the Function Selector (11) in the �OFF� position, press simultaneously the Sleep Set Button (8) and the Minute Set Button (9), or Hour Set Button (10) until the display shows the exact sleep time you wish the radio to play before switch off. To switch off the radio before the end of the programmed sleep time period, simply press the Snooze Button (5) once. SETTING PROJECTION CLOCK There are two separate clocks in this product. THE LED DIGITAL CLOCK AND THE PROJECTION CLOCK MUST BE SET SEPARATELY. 1. Switch on the projection clock with the Projection On/Off Selector (16). 2. Hold the clock radio with the clock display face down and the projection clock hinged out to face a dimly-lit wall opposite the projector. Focus the projection clock with the FOCUS thumbwheel (20). 3. To set the HOURS, press and hold the Projection Time Set Button (19) then repeatedly press the Projection Hour Set Button (22). Until the hour you require is displayed. 4. To set the MINUTES, press and hold the Projection Time Set Button (19) then repeatedly Downloaded from www.vandenborre.be

                              13 / 03 / 2013 SPECIFICATIONS AM 530-1600KHz FM 88-108 Mhz AC 230V~ 50Hz, 5W Downloaded from www.vandenborre.be