Sony BG-3S Service Manual

KV-2199XDK RM-952 – 58 – A 1 2 3 4 5 6 7 B C D D E F G H I (4) Schematic Diagram of F board 1 2 1 2 1 2 3 4 1 2 3 4 CN4603 CN4601 CN4602 T4601 F4601 C4602 C4601 C654 0.0047 250V VDR461 R4601 T4602 1P :TAB 2P :VH 2P :VH T.L.F T3.15A FUSE 250V 0.47 250V :PP # ERZV14D621 1M 1/2W # AC IN AC IN AC OUT AC OUT GND TO A BOARD CN104 TO A BOARD CN601 B-SSS10217-ME.-F..2199 F (CISPR) – F Board – F [CISPR] PRINTED WIRING BOARD ...

REF. NO. PART NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK KV-2199XDK RM-952 * A-1299-049-A A BOARD COMPLETE ******************** 1-900-702-13 LEAD ASSY (1CORE),JUMPER * 4-055-304-01 HOLDER, LED * 4-067-182-03 HOLDER, FBT 4-382-854-11 SCREW (M3X10), P, SW (+) 4-382-854-21 SCREW (M3X14), P, SW (+) 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3 C003 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C004 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C005 1-163-001-11 CE ...

KV-2199XDK RM-952 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size and vertical size. • Minimize the brightness setting. • Provide dot pattern. (1) Horizontal and Vertical Static Convergence (Moving vertically), adjust the V.STAT magnet so that the red, green and blue dots are on top of each other at the center of the screen. R G B G R B Center dot C board RV 702 V.STAT Magnet H. STAT VR 4 BMC (Hexapole) Magnet. If the red, green and blue dots are not balanced or aligned, then use the BMC magnet to adjust in the manner ...

KV-2199XDK RM-952 2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped White balance failure 5 times * One flash count is not used for self-diagnostic. 3. STOPPING THE STANDBY/TIMER FLASH Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing. Lamp ON 0.3 sec. Lamp OFF 3 sec. Lamp OFF 0.3 sec. 2 times 5 times STANDBY/SLEEP lamp ...

KV-2199XDK RM-952 12 Using Your New TV To Turn off temporarily Turn off completely Mute the sound Watch the video input (VCR, camcorder, etc.) Jump back to the previous channel Display the on-screen information* Adjust the volume of each TV program automatically * The picture, sound, and either the program number or video mode are displayed. The on-screen display for the picture and sound information disappears after about 3 seconds. Changing the on-screen display language 1 Press SELECT until “LANGUAGE / : ENGLISH”appears on the screen. 2 Press + or – to select “ “. Tip ...

– 46 – – 48 – A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 B C D D E F G H I (2) Schematic Diagram of A2/2 board HV 1 4 2 3 6 5 11 13 9 8 7 FV SV 10 14 1 2 1 2 3 4 5 1 2 3 1 2 3 4 5 6 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 1 3 4 7 8 9 10 1 2 1 2 3 4 5 6 1 2 3 4 1 2 1 2 3 4 1 1 2 3 4 -2 1 2 3 4 5 6 7 S 1 2 3 4 1 2 3 4 5 9 8 7 16 15 18 17 14 13 12 10 11 1 1 1 2 3 4 I O G I O G 1 3 4 5 1 2 4 3 1 2 3 S 1 3 4 5 6 8 9 2 10 11 -2 1 2 3 4 C629 C635 L508 C565 C560 C527 R569 C540 R578 C558 C541 C566 C505 C557 C529 C555 R568 C516 L515 R507 SG501 C568 R597 C511 R524 C553 C552 Q506 ...

KV-2199XDK RM-952 4 Y separation axis correction magnet adjustment. 1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] and [BRIGHTNESS] to [STANDARD] . 2. Adjust the Y separation axis correction magnet on the neck assembly so that the horizontal lines at the top and bottom of the screen are straight. Blue Red VM1 board Blue Red VM1 board Neck assy Neck assy Note 1. The Red and Blue magnets should be equally far from the horizontal center line. 2. Do not separate the Red and Blue magnets too far. (Less than 8 mm) (2) Dynamic Convergence Adjustment Preparation: • Befor ...

KV-2199XDK RM-952 4 Y separation axis correction magnet adjustment. 1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] and [BRIGHTNESS] to [STANDARD] . 2. Adjust the Y separation axis correction magnet on the neck assembly so that the horizontal lines at the top and bottom of the screen are straight. Blue Red VM1 board Blue Red VM1 board Neck assy Neck assy Note 1. The Red and Blue magnets should be equally far from the horizontal center line. 2. Do not separate the Red and Blue magnets too far. (Less than 8 mm) (2) Dynamic Convergence Adjustment Preparation: • Befor ...