VM Audio SRD10SBS Install Manual

1. Turn the gain and bass control all the way down (counterclockwise). 2. Turn the vehicle on, and make sure the source unit is turned on. 3. Insert a CD/DVD with undistorted music. 4. Start to increase the volume at the source unit until you hear distortion (about 90%). 5. Turn the volume down at the source unit until the distortion goes away. 6. At the amplifi er, slowly turn the Bass Boost control up (clockwise) until you hear a slight distortion from the speakers. 7. Turn the Bass Boost control back down until the distortion goes away. 8. When the Bass Boost control i ...

2. Route the remote wire with a wire length that expands from the stereo head unit all the way to the amplifi er’s negative power terminal. 3. Strip both ends of the remote wire by 1/2” to expose the wire. 4. Connect the remote wire to the stereo’s remote wire by twisting both wires together, and insulate the connection well with electrical tape. 5. Connect the other end of the remote wire to the amplifi er’s remote REM terminal. REMOTE The remote wire, when connected to the amplifi er, is designed to turn on the amplifi er automatic ...

receive low level signals from the RCA outputs of the stereo head unit. If your stereo head unit does not have RCA outputs, a High-to-Low level converter (not included) must be used. Both line inputs need to be connected to the stereo head unit in order to use all of the speaker outputs. Stereo RCA Cables Speaker Wires High-to-Low Level Converter (not included) Left Channel Right Channel Right Channel Left Channel 12 LINE OUTPUT Linking Amplifi er The pre-amp line outputs allow linking additional amplifi ers without the need t ...

screw holes to be drilled with a marker. WARNING! Be aware of gas tanks, gas lines, hydraulic lines and electrical wiring when drilling mounting holes to prevent serious or life-threatening injuries. Drill the holes on the marked spots with an electric drill. Secure the amplifi er with screws using a phillips screwdriver. Make sure to mount the amplifi er in a location where there is enough room to have access to the knobs and terminals. 16 CALIBRATION Setting Gain 1. Turn the gain and bass control all the way down (counterclockwise). 2. Turn the vehicle ...

Your product is covered by a limited warranty by VM Audio as established below: Mobile Electronics Limited Warranty Products purchased from an Authorized VM Audio Dealer are warranted to be free of defects in material and workmanship for one (1) year from the date of original purchase under normal usage. Products that are identifi ed as “refurbished” have a limited warranty of ninety (90) days from the date of original purchase. Dated proof of purchase (original receipt or invoice) will be required for all warranty claims. In the unlikely event tha ...

• Investigate the layout of your automobile thoroughly before drilling. • Place the amplifi er in a location that allows air to circulate around it to keep it cool. • If possible, mount the amplifi er vertically for proper heat dissipation. • Avoid mounting the amplifi er upside-down as this will not provide adequate ventilation for the amplifi er. • In order to prevent overheating, avoid covering the amplifi er with carpet or enclosing it behind the interior panels. • If the amplifi er is installed in a tight area, it m ...

signal strength going into the amplifi er. Bass Boost: Increases the bass level from +1dB up to +18dB. LPF Frequency: Low pass crossover frequency fi lter adjustment. REMOTE: Gain knob cable input plug to conveniently adjust the bass boost strength. Power LED: Power and protection amplifi er status indicator. Input: Line level audio inputs. Output: Line level audio outputs. 8 POWER CONNECTIONS 1. Carefully remove the end cap from the amplifi er where the power connections are located. 2. Strip 1/2 inch of insulation off each e ...

receive low level signals from the RCA outputs of the stereo head unit. If your stereo head unit does not have RCA outputs, a High-to-Low level converter (not included) must be used. Both line inputs need to be connected to the stereo head unit in order to use all of the speaker outputs. Stereo RCA Cables Speaker Wires High-to-Low Level Converter (not included) Left Channel Right Channel Right Channel Left Channel 12 LINE OUTPUT Linking Amplifi er The pre-amp line outputs allow linking additional amplifi ers without the need t ...