Speco O3FDP9 Quick Installation Manual

QUICK INSTALLATION GUIDE O3FDP9 Please read this guide carefully before installation and operation of the product.

it carefully before operating the product and retain it for future reference. Should you require any technical assistance, please contact Speco Technologies Technical Support. INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAUTION – To prevent electric shock and risk of the fire hazards � Do NOT use power source other than that specified. � Do NOT expose this appliance to rain or moisture. This installation should be made by a qualified service person and should conform to all local codes. The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION

the best picture quality. � Installation and services should only be carried out by an authorized personnel according to local safety regulations. � If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and have it checked by your authorized dealer before reusing. � Avoid installing the camera in extremely hot or cold places. � If you are not a certified person, never try to dismantle the camera. To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should be carried out by qualified personnel. � Avoid installing the camera in a place of high humidity. � Avoid installing the camera at a place exposed to gas or oil. � Don't point the camera directly at sunlight. � Please pay special attention to keep the unit from dropping or external shock during the process of transportation or handling. � Never try to touch the camera with wet hands. It may cause an electric shock. � Do not expose the camera to radioactivity. It can cause a serious damage on the image sensor. LIMITATION OF LIABILITY This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of the third party's right. This publication could include technical inaccuracies or typographical errors. Changes are added to the information herein, at any time, for the improvements of this publication and / or the corresponding product(s). DISCLAIMER OF WARRANTY In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance of the product, for the cases, including but not limited to below : (1) Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary, arising out of or relating to the product. (2) Personal injury or any damage caused by inappropriate use or negligent operation of the user. (3) Unauthorized disassembly, repair or modification of the product by the user. (4) Inconvenience or any loss when images are not displayed, due to any reason or cause including any failure or problem of the product. (5) Any problem, consequential inconvenience, or loss or damage, when combined with third party devices. (6) Any claim or action for damages, brought by any person or organization, due to a violation of privacy when the surveillance footage, for some reason, becomes public or is used for the purpose other than surveillance.

Key Features � 3.0 Mega pixel 1/2.8" SONY progressive scan CMOS image sensor for excellent image quality � 2.8mm wide angle lens � 3-axis design � Support for corridor view (in H.264) � Integrated motion detection with pre- and post-alarm image / video buffering � Supports CBR (Constant Bit Rate) and VBR (Variable Bit Rate) modes � Supports Tampering-Alarm � Controllable frame rate � Privacy Masking up to 8 areas � Built-in standard PoE (802.3af) � HTTPS support � Integrated E-Mail, FTP, DDNS and DHCP client Specifications CLASSIFICATION SPEC General CPU ARM1176JZF-STM ( 400 MHz, Instruction cache : 32kbyte, data cache : 16kbyte, MMU ) Flash 2Gbit Flash Memory SDRAM 2Gbit DDR3 Memory Image Pickup Image Sensor 3.1 Megapixel 1/2.8" SONY Progressive Scan CMOS Image Sensor Total Pixels 2065(H) x 1565(V) 3.23 Megapixel Effective Pixels 2065(H) x 1553(V) 3.21 Megapixel S/N Ratio More than 50dB Min. Illumination 0Lux (IR On) IR Distance 65’ Day & Night IR cut filter Lens 2.8mm fixed lens Video Video Compression H.264 High Profile @ Level 5.0 (2048 x 1536), @ Level 4.1 (Other resolutions), Motion JPEG Resolutions Up to 2048 x 1536 Frame Rate H.264 Up to 30fps with 2048 x 1536 MJPEG Up to 30fps with VGA Resolution Video Streaming Support Multi Stream with H.264, MJPEG Adjustable Frame Rate VBR / CBR in H.264 Image Setting Brightness, Contrast, Sharpness Day & Night Auto White Balance Auto Exposure Privacy Mask DSS, Corridor-view (in H.264), Mirror / V-Flip, etc. Backlight WDR Shutter Speed 1/4 ~ 1/2000 Noise Reduction 2D / 3DNR Network Dynamic IP SPECO DDNS (Free of Charge) Security Password Protection User Access Log HTTPS Encryption

System Integration Intelligent Video Motion detection 12 x 12 blocks Alarm Trigger Motion Detection, Tampering Alarm Firmware Upgrade Remote Upgrade via Network Physical Etc 1 x Factory Reset Button Memory Slot Save to Micro SD card with event mode and continuous mode Power Source DC 12V / 1.5A, POE (Power Over Ethernet) : 802.3af Power Consumption Max. 3.0W, Max. 5.0W with IR On Net Weight 10 oz Dimension(in) 5.12(∅) x 3.03(H) Environment Operating Temperature -14F ~ 122F Storage Temperature -4F ~ 140F � Specifications are subject to change without prior notice for improvement. 2. NAME AND FUNCTION OF EACH PART 2.1 Package Contents APPEARANCE DESCRIPTION IP Camera x 1 Installation Guide x 1 Drilling Template x 1 Tapping screw (Ø4 x 30) x 3 Plastic anchor x 3 CD x 1