Ampcontrol iMac Communications Manual

Designed and Manufactured in Australia by Ampcontrol Pty Ltd Integrated Monitoring and Control System iMAC2 Controller EtherNet/IP Communications Manual

Page 1 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART WARNING! The warning symbol highlights a potential risk of injury or death. Please share these warnings with other operators. CAUTION! The caution symbol highlights a potential risk of damage to equipment. Please share these cautions with other operators. NOTE The note symbol highlights key information. Please share these notes with other operators. ENVIRO The enviro (environmental) symbol highlights areas which may have an impact on the surrounding fauna and/or flora.

Page 2 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Copyright Notice The Ampcontrol iMAC2 Integrated Monitoring and Control system described in this document is the property of AMPCONTROL PTY LTD. It is furnished under a license agreement and is to be used only in accordance with the terms of the agreement. No part of the hardware or documentation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of AMPCONTROL PTY LTD. The iMAC signalling technique is protected by patent. Disclaimer While every effort has been made to assure the accuracy and clarity of this document, AMPCONTROL PTY LTD assumes no liability resulting from any omissions in this document, or from misuse of the information obtained herein. The information in this document has been carefully checked and is believed to be entirely reliable with all of the necessary information included. AMPCONTROL PTY LTD reserves the right to make changes to any products described herein to improve reliability, function, or design, and reserves the right to revise this document and make changes from time to time in content hereof with no obligation to notify any persons of revisions or changes. AMPCONTROL PTY LTD does not assume any liability arising out of the application or any use of any product or circuit described herein; neither does it convey license under its patent rights or the rights of others. Before You Begin Thank you for purchasing the Ampcontrol iMAC2 System. WARNING! In the interests of safety and correct equipment operation, please take the time to read and understand the content in this manual. Ampcontrol Contact Details 7 Billbrooke Close, Cameron Park, NSW, 2285 P +61 1300 267 373 | F +61 2 4903 4888 EMAIL: [email protected] WEB: ampcontrolgroup.com

Page 3 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART TABLE OF CONTENTS DOCUMENT SCOPE ................................................................................................. 5 1 Document Scope .............................................................................................. 5 1.1 Supplementary Documents .............................................................................. 5 1.2 1.2.1 System Documentation ........................................................................... 5 1.2.2 Module Documentation ........................................................................... 5 iMAC2 CONTROLLER ETHERNET/IP COMMUNICATIONS OVERVIEW ................. 6 2 Specifications ................................................................................................... 6 2.1 Connecting to the Ethernet Port for the First Time ............................................ 7 2.2 EtherNet/IP Protocol ....................................................................................... 10 2.3 THE iMAC2 CONTROLLER’S DATA TRANSFER .................................................... 11 3 Input Assembly Instance Layout ..................................................................... 11 3.1 Module Types ................................................................................................. 13 3.2 DATA HANDLING – RSLogix5000 APPLICATIONS ................................................ 15 4 UDTs .............................................................................................................. 15 4.1 4.1.1 iMac_SystemStatus_DT ....................................................................... 15 4.1.2 iMac_SystemControl_DT ...................................................................... 16 4.1.3 iMac_Ctrl_Runtime_DT ......................................................................... 17 4.1.4 iMac_Ctrl_LCD_DT ............................................................................... 18 4.1.5 iMac_Controller_DT .............................................................................. 18 4.1.6 iMac_Network_Config_Entry_DT .......................................................... 19 4.1.7 iMac_Network_Config_DT .................................................................... 20 4.1.8 iMac_STATUS_DT ............................................................................... 20 4.1.9 iMac_ERROR_DT ................................................................................ 21 4.1.10 iMac_AIM_AI_ModDT ......................................................................... 21 4.1.11 iMac_AIM_FLAGS_ModDT ................................................................. 22 4.1.12 iMac_AIM_Power_ModDT .................................................................. 22 4.1.13 iMac_DI4_ModDT ............................................................................... 23 4.1.14 iMac_DI8_ModDT ............................................................................... 23 4.1.15 iMac_GAI3_FLAGS_ModDT ............................................................... 24 4.1.16 iMac_GAI3_AI_ModDT ....................................................................... 25 4.1.17 iMac_IIM_ModDT ............................................................................... 25 4.1.18 iMac_LED4_ModDT............................................................................ 26 4.1.19 iMac_RIS_ModDT .............................................................................. 26

Page 4 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.20 iMac_RO4_ModDT ............................................................................. 27 4.1.21 iMac_RTD1_FLAGS_ModDT .............................................................. 27 4.1.22 iMac_RTD_Temp_ModDT .................................................................. 28 4.1.23 iMac_RTD3_FLAGS_ModDT .............................................................. 28 4.1.24 iMac_SIM_G_ModDT ......................................................................... 29 4.1.25 iMac_SIM_G2_ModDT ....................................................................... 29 4.1.26 iMac_SIM_P_ModDT .......................................................................... 30 4.1.27 iMac_SIM_T_ModDT .......................................................................... 30 4.1.28 iMac_SSW_Control_ModDT ............................................................... 31 4.1.29 iMac_SSW_FLAGS_ModDT ............................................................... 32 4.1.30 iMac_SSW_Value_ModDT ................................................................. 33 4.1.31 iMac_Modules_DT .............................................................................. 34 AOIs ............................................................................................................... 36 4.2 4.2.1 iMac_Demux_AOI ................................................................................. 36 4.2.2 iMac_Clear_Data_AOI .......................................................................... 36 4.2.3 iMac_Errors_Assign_AOI ...................................................................... 37 4.2.4 iMac_Status_Assign_AOI ..................................................................... 37 RSLogix5000 Program/Routine Usage ........................................................... 37 4.3 Example Setup ............................................................................................... 39 4.4 TABLE OF FIGURES Figure 1: Location of the Ethernet Communications Port ..................................................... 6 Figure 2: Location of Ethernet Reset Switch ........................................................................ 7 Figure 3: Updating the Ethernet Port Settings of the Connectable Device ............................ 8 Figure 4: Updating the iMAC2 Controller Ethernet Port Settings .......................................... 9 Figure 5: Minimum Program/Routine requirements for getting iMAC2 EtherNet/IP data in RSLogix5000 ..................................................................................................................... 38 Figure 6: Generic Ethernet Module setup for iMAC2 EIP data. .......................................... 38 Figure 7: iMAC2 Demonstration Box .................................................................................. 39 Figure 8: iMAC web interface online modules. ................................................................... 40 Figure 9: Node 30 data transferred to the PLC. .................................................................. 41

Page 5 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART DOCUMENT SCOPE 1 Document Scope 1.1 This document is intended to provide a detailed explanation of the communications protocols supported by the iMAC2 Controller’s Ethernet port. This document is not intended to provide information on the operation of the overall iMAC System, individual modules or instruction on programming the iMAC2 Controller or modules. Please refer to the relevant supplementary documents for this information. Supplementary Documents 1.2 The iMAC2 Controller Ethernet/IP Communications Manual is intended to be read in conjunction with the following documents: 1.2.1 System Documentation  IMAC2B010 iMAC2 Controller Ethernet Communications Manual  IMAC2B009 iMAC2 System User Manual  IMAC2B011 iMAC2 Controller Web Interface Manual  IMACB094 iMAC System Installation Requirements  IMACB155 iMAC SIL Emergency Stop Qualification  IMACB005 iMAC Module Programming Manual 1.2.2 Module Documentation  IMACB003 iMAC RO4 Module Technical Datasheet  IMACB018 iMAC LPU Module Technical Datasheet  IMACB020 iMAC DI8 Module Technical Datasheet  IMACB045 iMAC IIM Module Technical Datasheet  IMACB046 iMAC DI4 Module Technical Datasheet  IMACB047 iMAC EOL/MEOL Module Technical Datasheet  IMACB060 iMAC LED4 Module Technical Datasheet  IMACB061 iMAC SSW Module Technical Datasheet  IMACB062 iMAC SQM Module Technical Datasheet  IMACB066 iMAC AIM Module Technical Datasheet  IMACB067 iMAC RTD1 Module Technical Datasheet  IMACB141 iMAC ARM Module Technical Datasheet  IMACB142 iMAC CRM Module Technical Datasheet  IMACB143 iMAC EMM Module Technical Datasheet  IMACB144 iMAC GRM Module Technical Datasheet  IMACB146 iMAC IRK Keypad Technical Datasheet  IMACB147 iMAC PIM Module Technical Datasheet  IMACB148 iMAC SIM-G Module Technical Datasheet  IMACB149 iMAC SIM-G2 Module Technical Datasheet  IMACB150 iMAC SIM-T Module Technical Datasheet  IMACB151 iMAC MLB Barrier Technical Datasheet  IMACB152 iMAC SLB Barrier Technical Datasheet  IMACB154 iMAC SIM-P Module Technical Datasheet

Page 6 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 2 iMAC2 CONTROLLER ETHERNET/IP COMMUNICATIONS OVERVIEW The iMAC2 Controller is equipped with an Ethernet port and a serial communication port. This manual details the use of the Ethernet port. For information pertaining to the use of the serial communications port, refer to the IMACB153 iMAC Controller Serial Communications Manual. NOTE The Ethernet port is a read only communications port. The iMAC2 Controller has been manufactured in this way to maintain the SIL “Proven in Use” statistics of the previous iMAC Controller. Specifications 2.1 Figure 1: Location of the Ethernet Communications Port Table 1: Ethernet Communications Port Specifications Ethernet TCP/IP Port Available Interfaces RJ45 10/100MB, Auto Negotiation Applicable Standards IEEE 802.3u, IEEE 802.3x Cable Requirements 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) Supported Protocols EtherNet/IP (Port 2222), NTP (for time synchronisation), Webserver (for configuration, data viewing and diagnostic functions) Maximum Request Rate 400ms Recommended Response Timeout 200ms Maximum Concurrent Web Connections The iMAC2 Controller allows four users to access the web server. Ethernet Communications Port Name Link Activity Link Speed Operation On when valid link is detected. Blinks when activity is detected. On when operating speed is 100Mbps. Off when the line speed is 10Mbps, or during line isolation. Link Activity LED (Yellow) Link Speed LED (Green) Colour Yellow Green

Page 7 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Connecting to the Ethernet Port for the First Time 2.2 The iMAC2 Controller’s factory default Ethernet IPv4 settings are as follows: Table 2: Default Ethernet Communications Port Settings Default Ethernet IPv4 Settings IP Address 10.1.1.10 Subnet Mask 255.255.255.0 If the Controller’s IPv4 settings have been changed, they can be restored to the factory default settings by pressing the iMAC2 Controller’s Ethernet Reset button for 4 seconds (The internal iMAC2 Controller status LED will turn on solid while the reset button is depressed, after 4 seconds the LED will change to a fast flash to indicate settings have been reset to default, after which the button can then be released). Figure 2: Location of Ethernet Reset Switch Ethernet Reset Switch

Page 8 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART The iMAC2 Controller’s Ethernet port settings are not configurable via the HMI; they must be altered using the iMAC2 Web Interface. The Controller’s web server can be accessed using a one-to-one Ethernet connection with an Ethernet enabled device. Temporarily configure your device’s Ethernet port as follows: Figure 3: Updating the Ethernet Port Settings of the Connectable Device Once the network adaptor of the external device has been configured as shown in Figure 3, connect the iMAC2 Controller’s Ethernet port directly to your device’s Ethernet port, the iMAC2 Controller should then be able to be pinged at 10.1.1.10. Once a successful ping has been performed, open a web browser (Chrome recommended) and enter the iMAC2 Controller’s IP address into the address bar: http://10.1.1.10; the iMAC2 Controller web pages should load within a few seconds.

Page 9 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Navigate to the Ethernet Settings page to configure the IP settings for the iMAC2 Controller: Figure 4: Updating the iMAC2 Controller Ethernet Port Settings For information on this process, refer to the IMAC2B011 iMAC2 Controller Web Interface Manual.

Page 10 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART EtherNet/IP Protocol 2.3 The iMAC2 Controller uses industry standard EtherNet/IP protocol for exchanging data with compatible Ethernet devices. The EtherNet/IP protocol is the adaptation of the Common Industrial Protocol to the Ethernet platform. EtherNet/IP allows both implicit (synchronous) and Explicit (asynchronous) messaging, with UDP port 2222 being used for implicit messages. The iMAC2 data transfer is carried out via the following Assembly Instances:  Input Assembly Instance 100: defined by a block of 100 (16-bit) words.  Output Assembly Instance 150: defined by a block of 30 (16-bit) words. (Not currently used).  Config Assembly Instance 50: defined by a block of 0 bytes. (Not currently used). The requested packet interval is configurable, and to guarantee all iMAC module data is sent to the PLC this interval needs to be set to a rate faster than the iMAC controller is scanning its connected modules (referred to as the iMAC Controller’s “linespeed”). The linespeed is set by the iMAC SLP code, and can be configured in the range from 300 to 1000. There are three commonly used linespeeds: 300, 500 and 1000. The following table specifies the maximum EIP “packet interval time” that can be used for each of the commonly used linespeeds. Table 3: Maximum EIP Packet Interval iMAC Linespeed EIP Packet Interval (max) 1000 100 ms 500 225 ms 300 400 ms The requested packet interval defaults to 225msec, with a maximum allowed being 400msec.

Page 11 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART THE iMAC2 CONTROLLER’S DATA TRANSFER 3 The data transferred over EtherNet/IP is a progressive transfer of the iMAC2 data contained within the iMAC2 Data Point Table. Each implicit message transfer updates the input assembly instance as follows: Input Assembly Instance Layout 3.1 Table 4: iMAC2 Controller Input Assembly Instance Data Structure Word Offset Description 0 Start Block Address 1 Module 1 Data 2 Module 1 Status 3 Module 1 Resistance 4 Module 1 ErrCnt 5 Module 2 Data 6 Module 2 Status 7 Module 2 Resistance 8 Module 2 ErrCnt 9 Module 3 Data 10 Module 3 Status 11 Module 3 Resistance 12 Module 3 ErrCnt 13 Module 4 Data 14 Module 4 Status 15 Module 4 Resistance 16 Module 4 ErrCnt 17 Unused 18 Unused 19 Unused

Page 12 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 20 System Status (Modbus 0x100) 21 System Control (Modbus 0x400) 22 System ID and Control (Modbus 0x401) 23 L1 Data Block Just Complete (Modbus 0x406) 24 Main Loop Timer Counter(SLP) (Modbus 0x408) 25 Module Rollcall Control (Modbus 0x409) 26 Rollcall Address (Modbus 0x40A) 27 Rollcall Serial Number (Modbus 0x40B) 28 Rollcall Type Register (Modbus 0x40C) 29 Rollcall Block Number (Modbus 0x40D) 30 Rollcall Parameter 1 (Modbus 0x40E) 31 Rollcall Parameter 2 (Modbus 0x40F) 32 Rollcall Parameter 3 (Modbus 0x410) 33 Rollcall Parameter 4 (Modbus 0x411) 34 Mimic Key Press (Modbus 0x60F) 35 SLP Fault Register (Modbus 0x50C) 36 SLP Fault Address (Modbus 0x50D) 37 Controller Hardware Flags (Modbus 0x600) 38 Controller Temperature (Modbus 0x601) 39 EOL Series Resistance (Modbus 0x200) 40 EOL Shunt Resistance (Modbus 0x300) 41 EOL Offline Count (Modbus 0x415) 42 EOL Clash Count (Modbus 0x416) 43 EOL Serial Number (Modbus 0x404) 44 MEOL Status (Modbus 0x0160)

Page 13 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 45 MEOL Series Resistance (Modbus 0x260) 46 MEOL Offline / Clash Count (Modbus 0x360) 47 MEOL serial number (Modbus 0x060) 48 Unused 49 Unused 50 to 73 General Buffer Registers (24 of these) (Modbus 0x0480 to 0x0498) 74 Unused 75 to 98 Non Volatile Memory (24 registers) (Modbus 0x0520 to 0x0538) 99 Unused Therefore, module data for four modules is sent from the iMAC2 at each packet time (offset 1 to 16), as well as controller data (offset 20 to 37), EOL/MEOL module data (offset 38 to 47), General Buffer data (offset 50 to 73) and Non-Volatile Memory data (offset 75 to 98). The Start Block Address at offset 0 specifies the node address of the first of four modules in each transfer. This Start Block Address is incremented by 4 for each implicit message transfer. So that data for nodes 0, 1, 2 and 3 is updated at packet time t, then data for nodes 4, 5, 6 and 7 is updated at packet time t+1, and so on until data for nodes 252, 253, 254 and 255 is sent (at packet time t+63). Then the Start Block Address is reset to 0, and data for nodes 0, 1, 2 and 3 is updated again. Applications requiring iMAC2 data over EtherNet/IP need to take this progressive data update into account. (This is taken care of in the RSLogix5000 Add-On Instruction described later). Module Types 3.2 The table below provides the module types that are associated with the possible values of the “Rollcall Type”. This is reproduced from the document “IMAC2B010 iMAC2 Controller Ethernet Communications Manual”.

Page 14 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Table 5: Module type designations. Module Type Table Corresponding Values for Rollcall Type Register (Address 1036, 40Ch) Value Module Type Value Module Type Decimal Hexadecimal Decimal Hexadecimal 0 0000h Reserved 32 0020h LED4 Module 1 0001h Controller 33 0021h EMM Module 2 0002h TCD2 DIPSwitch 34 0022h Undefined #34 3 0003h EOL Module 35 0023h SIM-P Module 4 0004h SQM Module 36 0024h SIM-T Module 5 0005h DI2/4 Module 37 0025h SIM-G Module 6 0006h Undefined #6 38 0026h DI5 Module 7 0007h Undefined #7 39 0027h RO4 Module 8 0008h TCD4 Long 40 0028h TO4 Module 9 0009h TCD4 Module 41 0029h GCA Status 10 000Ah RTD3 Status 42 002Ah GCA 15Min Tally 11 000Bh RTD3 Temp 1 43 002Bh GCA 8Hr Tally 12 000Ch RTD3 Temp 2 44 002Ch GCA 24Hr Tally 13 000Dh RTD3 Temp 3 45 002Dh GCA Raw Count 14 000Eh DI4L Module 46 002Eh DI8 Module 15 000Fh DI4 Module 47 002Fh RIS Module 16 0010h IIM Module 48 0030h AIM Status 17 0011h PGM-A Programr 49 0031h AIM Analog 18 0012h MEOL Module 50 0032h AIM PwrSupply 19 0013h TCD0 Module 51 0033h CRM Module 20 0014h SSW Status 52 0034h ARM Module 21 0015h SSW Control 53 0035h GRM Module 22 0016h SSW % Slip 54 0036h RTD1 Status 23 0017h SSW % Speed 55 0037h RTD1 Temp 24 0018h SSW Linr Speed 56 0038h SIM-G2 Module 25 0019h TCRD Input 57 0039h FCP DigInputs 26 001Ah TCRD Output 58 003Ah FCP DigOutputs 27 001Bh GAI3 Status 59 003Bh FCP AnaInputs 28 001Ch GAI3 Analogue #1 60 003Ch FCP AnaOutputs 29 001Dh GAI3 Analogue #2 61 003Dh Undefined #61 30 001Eh GAI3 Analogue #3 62 003Eh Undefined #62 31 001Fh RKM Keypad 63 003Fh Undefined #63

Page 15 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART DATA HANDLING – RSLogix5000 APPLICATIONS 4 A set of RSLogix5000 user-defined data types (UDTs) and add-on instructions (AOIs) have been constructed to retrieve iMAC2 data over the new EtherNet/IP connection, for connection to ControlLogix PLCs. These components will be described here. UDTs 4.1 There are module-specific UDTs, as well as generic UDTs used by the module-specific UDTs. These will all be described in a logical order. 4.1.1 iMac_SystemStatus_DT This UDT stores the iMAC2 Controller Runtime System Status bits. It is used by iMac_Ctrl_Runtime_DT. It has the following members. Member Name Data Type Description RefreshCycle BOOL Set by the controller at the end of every refresh cycle (refresh cycle = all 255 module addresses have been scanned). May be cleared by writing a 0 into this bit using application (SLP) software. L1ChksErr BOOL Set by the controller when a checksum error is detected on L1 fieldbus. May be cleared by writing a 0 into this bit using application (SLP) software. L1Ok BOOL Set by the controller when a L1 fieldbus scan completes with no errors detected. May be cleared by writing a 0 into this bit using application (SLP) software. L2ChksErr BOOL Set by the controller when a checksum error is detected on L2 fieldbus. May be cleared by writing a 0 into this bit using application (SLP) software. L2Active BOOL Set by controller when it detects an active fieldbus from another controller on its L2 port. Often used to condition the operation of the L2 LED on the controller. CtrlRelayState BOOL Status of the Control Relay. 1 = Energised. 0 = De-energised. AuxRelayState BOOL Status of the Auxiliary Relay. 1 = Energised. 0 = De-energised. EOL_OK BOOL Set by controller when EOL module is being detected on the L1 fieldbus with no faults, clear otherwise. EOL_SC BOOL Set by controller when the L1 fieldbus is short circuited (R<1000Ω), clear otherwise EOL_OC BOOL Set by controller when EOL module is not detected on the L1 fieldbus and the fieldbus is not short circuited, clear otherwise. EOL_CLASH BOOL Set by controller when two EOL modules are detected on the L1 fieldbus, clear otherwise.

Page 16 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART UART_Rx BOOL Set by controller when its serial port is receiving data UART_Tx BOOL Set by controller when its serial port is transmitting data EOL_SC BOOL Set by controller when the L1 fieldbus is short circuited (R<1000Ω), clear otherwise 4.1.2 iMac_SystemControl_DT This UDT stores the iMAC2 Controller Runtime System Control bits. It is used by iMac_Ctrl_Runtime_DT. It has the following members. Member Name Data Type Description StartUp BOOL Set by controller on first SLP loop following power up Always1 BOOL This bit is always set to 1 SeqDownFromL2 BOOL Sequence Down Bit from Upstream iMAC Controller SeqUpFromL1 BOOL Sequence Up Bit from Downstream iMAC Controller/SQM module SwInput1 BOOL iMAC Controller SW1 status: 1 = closed, 0 = open. SwInput2 BOOL iMAC Controller SW2 status: 1 = closed, 0 = open. SwInput3 BOOL iMAC Controller SW3 status: 1 = closed, 0 = open. AsrtCtrlRelay BOOL Set by application (SLP) software to attempt to energise the CR relay. CR will energise if and only if EOL Module comms is also healthy. Clear to de- energise CR relay. AsrtAuxRelay BOOL Set by application (SLP) software to energise AR relay. Clear to de-energise AR relay. SeqUpOnL2 BOOL Upstream sequence control bit SeqDownOnL1 BOOL Downstream sequence control bit EnFlashWrite BOOL Enables data to be written to the iMAC Controller’s flash memory using Modbus write commands FullSysMenu BOOL The following menu functions are disabled when FullSysMenu = 0 & enabled when FullSysMenu = 1 - System Menu ‘CLR DPT’ item, Maintenance page F1 - Clear individual OnScan Bit MinSysMenu BOOL The following menu functions are disabled when MinSysMenu = 0 & enabled when MinSysMenu = 1 - System Menu (SHIFT+MENU), Debug Menu,

Page 17 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.3 iMac_Ctrl_Runtime_DT This UDT stores the iMAC2 Controller Runtime data. It is used by iMac_Controller_DT. It has the following members. Maintenance page F4 – Clear individual OFFLINE/CLASH COUNTERS DisableWriteCmds BOOL Prevents Modbus Master devices writing to iMAC Controller Modbus registers Member Name Data Type Description SystemStatus iMac_SystemStatus_DT System Status SystemControl iMac_SystemControl_DT System Control SysIdLeds INT System ID and LED control L1BlockJustDone INT L1 Data Block Just Complete LoopTimeSLP INT Main Loop Timer Counter (SLP) RollcallControl INT Module Rollcall Control RollcallAddress INT Rollcall Address RollcallSerNum INT Rollcall Serial Number RollcallModType INT Rollcall Type Register RollcallBlckNum INT Rollcall Block Number RollcallParam1 INT Rollcall Parameter 1 RollcallParam2 INT Rollcall Parameter 2 RollcallParam3 INT Rollcall Parameter 3 RollcallParam4 INT Rollcall Parameter 4 MimicKeyPress INT Mimic Key Press SLPFaultRegister INT SLP Fault Register SLPFaultAddress INT SLP Fault Address HardwareFlags INT Controller Hardware Flags ControllerTemp INT Controller Temperature

Page 18 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.4 iMac_Ctrl_LCD_DT This UDT stores the iMAC2 Controller LCD data. It is included in the iMac_Controller_DT, but is not currently used. It has the following members. Member Name Data Type Description LCD_String_Data_Row1 INT[10] LCD String Data Row 1 LCD_String_Data_Row2 INT[10] LCD String Data Row 2 LCD_String_Data_Row3 INT[10] LCD String Data Row 3 LCD_String_Data_Row4 INT[10] LCD String Data Row 4 LCD_Cursor_Location INT LCD Cursor Location 4.1.5 iMac_Controller_DT This UDT stores the iMAC2 Controller data, including the data for all possible 256 modules in an iMAC network. It is a stand-alone data type. It has the following members. EOL_Status INT EOL Status EOL_Series_Resistance INT EOL Series Resistance EOL_Shunt_Resistance INT EOL Shunt Resistance EOLS_OC INT EOL Offline Count EOLS_Clash INT EOL Clash Count EOL_SerNum INT EOL Serial Number MEOL_Status INT MEOL Status MEOL_Series_Resistance INT MEOL Series Resistance MEOLS_Offline_Clash_Count INT MEOL Offline + Clash Count MEOL_SerNum INT MEOL Serial Number Member Name Data Type Description DATA INT[256] Controller Data. STATUS INT[256] Controller Status.

Page 19 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Note that the LCD data is not currently retrieved from the iMAC2 over EtherNet/IP, and so the LCD member is empty. 4.1.6 iMac_Network_Config_Entry_DT This UDT defines the iMAC2 network configuration Lookup table entry data. It is used by iMac_Network_Config_DT. It has the following members. Note that the Module_Type member has type numbers that follow the numbering defined in the iMAC2 system, and reproduced in Table 5: Module type designations. RESIST INT[256] Controller Resistance entries. ERROR INT[256] Controller Errors. Runtime iMac_Ctrl_Runtime_DT Run-time data. LCD iMac_Ctrl_LCD_DT LCD-related data. GENBUFF INT[24] General Buffer registers (area 480). NVM INT[24] User NVM registers (area 520). Member Name Data Type Description Module_Type DINT Network types are listed in the document 'IMAC2B010 iMAC2 Controller Ethernet Communications Manual' Module_Type_Data1 DINT Type Data1 is: For SIM_G, SIM-G2, SIM-P and SIM-T modules: references the SIM-G, SIM-G2, SIM-P and SIM-T unit; for all other modules, this member is currently not used. Module_Type_Data2 DINT Type Data2 is: For SIM_G, SIM-G2, SIM-P and SIM-T modules: this member references the register index; for all other modules, this member is currently not used.

Page 20 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.7 iMac_Network_Config_DT This UDT stores the iMAC2 network configuration information (the lookup table). It has one member as follows. 4.1.8 iMac_STATUS_DT This UDT stores the iMAC Status Bit information. It is used by all module UDTs to be described hereafter. It has the following members. Member Name Data Type Description Lookup_Table iMac_Network_Config_Entry_DT[256] The configuration of up to 256 iMAC modules in a network attached to an iMAC controller; each module is identified by the module type. Member Name Data Type Description OnScanBit BOOL Set by the controller when it first detects an input module address online on its L1 fieldbus. May be cleared by application (SLP) software. (POR=0) L1ClashBit BOOL Set by the controller when two input modules transmit different data on the same address, clear otherwise. Global BOOL Must be intentionally set by application (SLP) software if the corresponding data address needs to be published up the L2 fieldbus, thus making it a Global Address. L1OwnBit BOOL Set by the controller when it detects an input module address on its L1 fieldbus, cleared if module not detected. L2OwnBit BOOL Set by the controller when it detects the corresponding address on its L2 fieldbus. The Global Select bit for this address must be set to allow the controller to “see” up its L2 fieldbus. This should be done during the STARTUP segment of the application (SLP) software. SysOwnBit BOOL Must be intentionally set application (SLP) software when the corresponding data register is to be owned by the system. Setting this bit forces the corresponding data register to be an output. All addresses are assumed to be an input unless this bit is set. If an input module is connected to a system owned address on L1, a L1 clash error will occur. L2ClashBit BOOL Set by the controller when it detects the address is Online on both its L1 and L2 ports if the address Global Select bit is set. HighByteBit BOOL Must be intentionally set by application (SLP) software when the corresponding data register is to be partially owned by the system. Low byte of data register

Page 21 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.9 iMac_ERROR_DT This UDT stores the iMAC module Error information. It is used by most of the module UDTs to be described hereafter. It has the following members. 4.1.10 iMac_AIM_AI_ModDT This UDT stores the iMAC AIM Analog Input Module Data Type information (Note – all UDTs for iMAC modules have names ending with _ModDT, to distinguish them from other generic UDTs defined here). It has the following members. remains as input, but SLP can now write into high byte for output functions. GenPurpose0 BOOL General purpose use in application (SLP) software. GenPurpose1 BOOL General purpose use in application (SLP) software. GenPurpose2 BOOL General purpose use in application (SLP) software. GenPurpose3 BOOL General purpose use in application (SLP) software. GenPurpose4 BOOL General purpose use in application (SLP) software. GenPurpose5 BOOL General purpose use in application (SLP) software. GenPurpose6 BOOL General purpose use in application (SLP) software. GenPurpose7 BOOL General purpose use in application (SLP) software. Member Name Data Type Description Module_Offline_Count INT This count is incremented every data scan that there is no owner of the module address for which there was once an owner. Module_Clash_Count INT This count is incremented every time that a data scan occurs when L1 Clash = 1 (ie increments each time an address is scanned for which there are two modules with the same address that are transmitting different input data). Member Name Data Type Description AIM_Analogue_Input INT Module Analogue Input AIM_Analogue_Status iMac_STATUS_DT Module Status AIM_Analogue_Resist INT Module Resistance Value

Page 22 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Note that all module-related UDTs have the specific Data members, plus status bits, resistance value and error counts (although the LED4 and RO4 modules don’t have resistance or error members, and the IIM Module has an extra IIM_LEDs member). 4.1.11 iMac_AIM_FLAGS_ModDT This UDT stores the iMAC AIM Analog Flags Module Data Type information. It has the following members. 4.1.12 iMac_AIM_Power_ModDT This UDT stores the iMAC AIM Power Supply Module data. It has the following members. AIM_Analogue_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description AIM_FLAGS_Bit0_AI_LT_SP3 BOOL Module Flags - Analogue input < Set point 1 AIM_FLAGS_Bit1_AI_GE_SP2 BOOL Module Flags - Analogue input >= Set point 2 AIM_FLAGS_Bit2_AI_GE_SP3 BOOL Module Flags - Analogue input >= Set point 3 AIM_FLAGS_Bit3_AI_betw_1_2 BOOL Module Flags - Set point 1 ≤ Analogue input < Set point 2 AIM_FLAGS_Bit4_AI_betw_2_3 BOOL Module Flags - Set point 2 ≤ Analogue input < Set point 3 AIM_FLAGS_Bit5_PS_LT_SPA BOOL Module Flags - Power Supply < SP A (warn) AIM_FLAGS_Bit6_PS_LT_SPB BOOL Module Flags - Power Supply < SP B (trip) AIM_FLAGS_Status iMac_STATUS_DT Module Status AIM_FLAGS_Resist INT Module Resistance Value AIM_FLAGS_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description AIM_Power_Supply INT Module Power Supply Data AIM_Power_Supply_Status iMac_STATUS_DT Module Status AIM_Power_Supply_Resist INT Module Resistance Value

Page 23 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.13 iMac_DI4_ModDT This UDT stores the iMAC DI4 Module data. It has the following members. 4.1.14 iMac_DI8_ModDT This UDT stores the iMAC DI8 Module data. It has the following members. AIM_Power_Supply_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description DI4_Inputs_IP1 BOOL Module Input IP1 DI4_Inputs_IP2 BOOL Module Input IP2 DI4_Inputs_IP3 BOOL Module Input IP3 DI4_Inputs_IP4 BOOL Module Input IP4 DI4_Inputs_Applic_Dept SINT Module Input Data High Byte - Application Dependent DI4_Status iMac_STATUS_DT Module Status DI4_Resist INT Module Resistance Value DI4_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description DI8_Inputs_IP1 BOOL Module Input IP1 DI8_Inputs_IP2 BOOL Module Input IP2 DI8_Inputs_IP3 BOOL Module Input IP3 DI8_Inputs_IP4 BOOL Module Input IP4 DI8_Inputs_IP5 BOOL Module Input IP5 DI8_Inputs_IP6 BOOL Module Input IP6 DI8_Inputs_IP7 BOOL Module Input IP7 DI8_Inputs_IP8 BOOL Module Input IP8

Page 24 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.15 iMac_GAI3_FLAGS_ModDT This UDT stores the iMAC GAI3 Module Status data. It has the following members. DI8_Inputs_Applic_Dept SINT Module Input Data High Byte - Application Dependent DI8_Status iMac_STATUS_DT Module Status DI8_Resist INT Module Resistance Value DI8_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description GAI3_FLAGS_Bit0_AI1_ALM BOOL Module Flags - Analogue input 1 Alarm Bit (1=Alarm; 0=No Alarm). GAI3_FLAGS_Bit1_AI2_ALM BOOL Module Flags - Analogue input 2 Alarm Bit (1=Alarm; 0=No Alarm). GAI3_FLAGS_Bit2_AI3_ALM BOOL Module Flags - Analogue input 3 Alarm Bit (1=Alarm; 0=No Alarm). GAI3_FLAGS_Bit3_ADC_Fail BOOL Module Flags - GAI3 Internal Fault (ADC Fail) (1=Fault; 0=No Fault). GAI3_FLAGS_Bit8_AI1_OL_Status BOOL Module Flags - AI Module 1 Online Status (1=Online; 0=Offline). GAI3_FLAGS_Bit9_AI2_OL_Status BOOL Module Flags - AI Module 2 Online Status (1=Online; 0=Offline). GAI3_FLAGS_Bit10_AI3_OL_Status BOOL Module Flags - AI Module 3 Online Status (1=Online; 0=Offline). GAI3_FLAGS_Status iMac_STATUS_DT Module Status GAI3_FLAGS_Resist INT Module Resistance Value GAI3_FLAGS_Errors iMac_ERROR_DT Module Error Counters

Page 25 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.16 iMac_GAI3_AI_ModDT This UDT stores the iMAC GAI3 Module Analogue data. It is used for the three analogue values associated with the GAI3 module. It has the following members. 4.1.17 iMac_IIM_ModDT This UDT stores the iMAC IIM Module data. It has the following members. Member Name Data Type Description GAI3_Analogue_Input INT Module Analogue Input GAI3_Analogue_Status iMac_STATUS_DT Module Status GAI3_Analogue_Resist INT Module Resistance Value GAI3_Analogue_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description IIM_Inputs_IP1 BOOL Module Input IP1 IIM_Inputs_IP2 BOOL Module Input IP2 IIM_Inputs_IP3 BOOL Module Input IP3 IIM_Inputs_IP4 BOOL Module Input IP4 IIM_Inputs_IP5 BOOL Module Input IP5 IIM_Inputs_Bit5_ALine_Monitor_IP BOOL Module Input Data - A-line Monitor IP IIM_Inputs_Bit7_RandomBit BOOL Module Input Data - Random Bit IIM_Inputs_Applic_Dept SINT Module Input Data High Byte - Application Dependent IIM_Status iMac_STATUS_DT Module Status IIM_Resist INT Module Resistance Value IIM_Errors iMac_ERROR_DT Module Error Counters IIM_LEDs INT LED Output Data

Page 26 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.18 iMac_LED4_ModDT This UDT stores the iMAC LED4 Module data. It has the following members. 4.1.19 iMac_RIS_ModDT This UDT stores the iMAC RIS Module data. It has the following members. Member Name Data Type Description LED4_Outputs_LED1 BOOL Module Output LEDs - LED1 LED4_Outputs_LED2 BOOL Module Output LEDs - LED2 LED4_Outputs_LED3 BOOL Module Output LEDs - LED3 LED4_Outputs_LED4 BOOL Module Output LEDs - LED4 LED4_Status iMac_STATUS_DT Module Status Member Name Data Type Description RIS_Inputs_IP1 BOOL Module Input IP1 RIS_Inputs_IP2 BOOL Module Input IP2 RIS_Inputs_IP3 BOOL Module Input IP3 RIS_Inputs_IP4 BOOL Module Input IP4 RIS_Inputs_IP5 BOOL Module Input IP5 RIS_Inputs_Bit5_ALine_Monitor_IP BOOL Module Input Data - A-line Monitor IP RIS_Inputs_Bit7_RandomBit BOOL Module Input Data - Random Bit RIS_Inputs_Applic_Dept SINT Module Input Data High Byte - Application Dependent RIS_Status iMac_STATUS_DT Module Status RIS_Resist INT Module Resistance Value RIS_Errors iMac_ERROR_DT Module Error Counters RIS_LEDs INT LED Output Data

Page 27 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.20 iMac_RO4_ModDT This UDT stores the iMAC RO4 Isolation Output Module data. It has the following members. 4.1.21 iMac_RTD1_FLAGS_ModDT This UDT stores the iMAC RTD1 Flags Module data. It has the following members. Member Name Data Type Description RO4_Outputs_Relay1 BOOL Module Output Relays - Relay 1 RO4_Outputs_Relay2 BOOL Module Output Relays - Relay 2 RO4_Outputs_Relay3 BOOL Module Output Relays - Relay 3 RO4_Outputs_Relay4 BOOL Module Output Relays - Relay 4 RO4_Status iMac_STATUS_DT Module Status Member Name Data Type Description RTD1_FLAGS_Bit0_RTD_SC BOOL Module Flags - RTD Short Circuit RTD1_FLAGS_Bit1_RTD_OC BOOL Module Flags - RTD Open Circuit RTD1_FLAGS_Bit2_RTD_Wire_FLT BOOL Module Flags - RTD Sense Wire Fault RTD1_FLAGS_Bit3_Temp_OOR BOOL Module Flags - RTD Temperature Out of Range RTD1_FLAGS_Bit4_Low_Temp BOOL Module Flags - RTD Low Temperature Alarm RTD1_FLAGS_Bit5_High_Temp BOOL Module Flags - RTD High Temperature Alarm RTD1_FLAGS_Status iMac_STATUS_DT Module Status RTD1_FLAGS_Resist INT Module Resistance Value RTD1_FLAGS_Errors iMac_ERROR_DT Module Error Counters

Page 28 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.22 iMac_RTD_Temp_ModDT This UDT stores the iMAC RTD Temperature Input Module data. It can be used for RTD1 and RTD3 modules. It has the following members. 4.1.23 iMac_RTD3_FLAGS_ModDT This UDT stores the iMAC RTD3 Flags Module data. It has the following members. Member Name Data Type Description RTD_Temp_Input INT Module Temperature Input RTD_Temp_Status iMac_STATUS_DT Module Status RTD_Temp_Resist INT Module Resistance Value RTD_Temp_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description RTD3_FLAGS_Bit0_T1_ALM BOOL Module Flags - RTD3 Temp1 Alarm Setpoint RTD3_FLAGS_Bit1_T2_ALM BOOL Module Flags - RTD3 Temp2 Alarm Setpoint RTD3_FLAGS_Bit2_T3_ALM BOOL Module Flags - RTD3 Temp3 Alarm Setpoint RTD3_FLAGS_Bit3_ADC_Fail BOOL Module Flags - RTD3 Internal Fault (ADC Fail) RTD3_FLAGS_Bit4_T1_Temp_OOR BOOL Module Flags - RTD3 Temp1 Temperature Out of Range RTD3_FLAGS_Bit5_T2_Temp_OOR BOOL Module Flags - RTD3 Temp2 Temperature Out of Range RTD3_FLAGS_Bit6_T3_Temp_OOR BOOL Module Flags - RTD3 Temp3 Temperature Out of Range RTD3_FLAGS_Bit7_Calib_Error BOOL Module Flags - RTD3 Calibration Error RTD3_FLAGS_Bit8_T1_OL_Status BOOL Module Flags - RTD3 Temp1 Online Status RTD3_FLAGS_Bit9_T2_OL_Status BOOL Module Flags - RTD3 Temp2 Online Status RTD3_FLAGS_Bit10_T3_OL_Status BOOL Module Flags - RTD3 Temp3 Online Status RTD3_FLAGS_Bit12_T1_Wire_FLT BOOL Module Flags - RTD3 Temp1 Sense Wire Fault RTD3_FLAGS_Bit13_T2_Wire_FLT BOOL Module Flags - RTD3 Temp3 Sense Wire Fault

Page 29 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.24 iMac_SIM_G_ModDT This UDT stores the iMAC SIM-G Module data. It has the following members. 4.1.25 iMac_SIM_G2_ModDT This UDT stores the iMAC SIM-G2 Module data. It has the following members. RTD3_FLAGS_Bit14_T3_Wire_FLT BOOL Module Flags - RTD3 Temp2 Sense Wire Fault RTD1_FLAGS_Status iMac_STATUS_DT Module Status RTD1_FLAGS_Resist INT Module Resistance Value RTD1_FLAGS_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description SIM_G_ALARMS_CH1_2 INT Alarm Flags Channels 1 & 2 SIM_G_ALARMS_CH3_4 INT Alarm Flags Channels 3 & 4 SIM_G_FLAGS INT Gasguard Flags SIM_G_ANALOG_CH INT[4] Analogue Input Channels 1 to 4 SIM_G_DISPLAY_CH INT[4] Display Format Value Channels 1 to 4 SIM_G_RS485_ERRORS INT Error Count for RS 485 Communication SIM_G_SERIAL_NUM INT SIM-G Serial Number SIM_G_Status iMac_STATUS_DT[16] Module Status A0 to A15 SIM_G_Resist INT[16] Module Resistance Value A0 to A15 SIM_G_Error iMac_ERROR_DT[16] Module Error Counters A0 to A15 Member Name Data Type Description SIM_G2_ALARMS_CH1_2_CTRL1 INT Alarm Flags Channels 1 & 2, Controller 1 SIM_G2_ALARMS_CH3_4_CTRL1 INT Alarm Flags Channels 3 & 4, Controller 1 SIM_G2_ALARMS_CH1_2_CTRL2 INT Alarm Flags Channels 1 & 2, Controller 2 SIM_G2_ALARMS_CH3_4_CTRL2 INT Alarm Flags Channels 3 & 4, Controller 2

Page 30 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.26 iMac_SIM_P_ModDT This UDT stores the iMAC SIM-P Module data. It has the following members. 4.1.27 iMac_SIM_T_ModDT This UDT stores the iMAC SIM-T Module data. It has the following members. SIM_G2_ANALOG_CH_CTRL1 INT[4] Analogue Input Channels 1 to 4, Controller 1 SIM_G2_DISPLAY_FORMATS INT Channel Display Format Values - Controllers 1 (low byte) and 2 (high byte). SIM_G2_ANALOG_CH_CTRL2 INT[4] Analogue Input Channels 1 to 4, Controller 2 SIM_G2_RS485_ERRORS_CTRL1 INT Error Count for RS 485 Communication, Controller 1 SIM_G2_RS485_ERRORS_CTRL2 INT Error Count for RS 485 Communication, Controller 2 SIM_G2_SERIAL_NUM INT SIM-G2 Serial Number SIM_G2_Status iMac_STATUS_DT[16] Module Status A0 to A15 SIM_G2_Resist INT[16] Module Resistance Value A0 to A15 SIM_G2_Error iMac_ERROR_DT[16] Module Error Counters A0 to A15 Member Name Data Type Description SIM_P_RS485_ERRORS INT Error Count for RS485 Communication SIM_P_DATA_REGS INT[16] Data Registers 1 to 16 SIM_P_Status iMac_STATUS_DT[17] Module Status A0 to A16 SIM_P_Resist INT[17] Module Resistance Value A0 to A16 SIM_P_Error iMac_ERROR_DT[17] Module Error Counters A0 to A16 Member Name Data Type Description SIM_T_ALARMS_CH1_4 INT Alarm Flags Channels 1 to 4 SIM_T_ALARMS_CH5_8 INT Alarm Flags Channels 5 to 8

Page 31 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.28 iMac_SSW_Control_ModDT This UDT stores the iMAC SSW Module Control data. It has the following members. SIM_T_INPUT_STATUS INT Trolex Input Status 1 to 8 SIM_T_RELAY_STATUS INT Trolex Relay Status 1 to 8 SIM_T_ANALOG_CH INT[8] Analogue Input Channels 1 to 8 SIM_T_SOFTWARE_VERSION INT Software Version *10 (Value divided by 10 ie 27 = version 2.7) SIM_T_RS485_ERRORS INT Error Count for RS485 Communication SIM_T_SERIAL_NUM INT SIM-T Serial Number SIM_T_Status iMac_STATUS_DT[16] Module Status A0 to A15 SIM_T_Resist INT[16] Module Resistance Value A0 to A15 SIM_T_Error iMac_ERROR_DT[16] Module Error Counters A0 to A15 Member Name Data Type Description SSW_Control_Bit0_Setup_Mode BOOL Module Flags - Setup mode (1=Busy); The setup process is busy. SSW_Control_Bit1_Setup_Success BOOL Module Flags - Setup successful (1=Success); No failures occurred during the setup process. SSW_Control_Bit2_Setup_Failed BOOL Module Flags - Setup failed (1=Failed); The setup process failed due to a timeout or pulse rate failure. SSW_Control_Bit3_S1_Pulse_Slow BOOL Module Flags - Sensor 1 pulse rate too slow (1=Failed); Rate < 50ppm. SSW_Control_Bit4_S1_Pulse_Fast BOOL Module Flags - Sensor 1 pulse rate too fast (1=Failed); Rate > 5000ppm. SSW_Control_Bit5_S2_Pulse_Slow BOOL Module Flags - Sensor 2 pulse rate too slow (1=Failed); Rate < 50ppm. SSW_Control_Bit6_S2_Pulse_Fast BOOL Module Flags - Sensor 2 pulse rate too fast (1=Failed); Rate > 5000ppm. SSW_Control_Bit7_Setup_Timeout BOOL Module Flags - Setup timeout (1=Timeout); Setup failed to complete within 4 minutes.

Page 32 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.29 iMac_SSW_FLAGS_ModDT This UDT stores the iMAC SSW Module Status data. It has the following members. SSW_Control_Bit8_MC_Belt_State BOOL Module Flags - MC (belt run state) (1=Running); Usage: Indicate belt run condition. SSW_Control_Bit9_Slip_Trip_Test BOOL Module Flags - Slip trip Test (1=Simulate trip); Usage: Test trip mechanism. SSW_Control_Bit10_Reset_Trips BOOL Module Flags - Reset latched trips (1=Reset); Usage: Clear any latched trip flags; Requirements: No persistent trips present. SSW_Control_Bit11_Setup_Enable BOOL Module Flags - Setup enable (1=Enable); Usage: Start the normalisation sequence; Requirements: Belt stopped, trips cleared. SSW_Control_Status iMac_STATUS_DT Module Status SSW_Control_Resist INT Module Resistance Value SSW_Control_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description SSW_FLAGS_Bit0_Trip_Summary BOOL Module Flags - Trip summary (1=Trips exist); An OR function of all 'Tripped' flags SSW_FLAGS_Bit1_Brake_Relay BOOL Module Flags - Brake relay (1=Release); % speed > Brake release set point SSW_FLAGS_Bit2_Seq_Relay BOOL Module Flags - Sequence relay (1=Energized); % Speed > Sequence relay activation set point SSW_FLAGS_Bit3_CV_Stopped BOOL Module Flags - Conveyor stopped (1=Stopped); No pulses on either sensor, for a period of 20x slowest sensor pulse rate SSW_FLAGS_Bit4_S1_Pulses_FLT BOOL Module Flags - Sensor 1 pulses fault (1=Tripped); Inhibit timers expired, and drive pulse rate = 0 SSW_FLAGS_Bit5_S2_Pulses_FLT BOOL Module Flags - Sensor 2 pulses fault (1=Tripped); Inhibit timers expired, and drive pulse rate = 0 SSW_FLAGS_Bit6_S1_Conn_FLT BOOL Module Flags - Sensor 1 connection fault

Page 33 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.30 iMac_SSW_Value_ModDT This UDT stores the iMAC SSW Module % Slip, % Speed or Linear Speed value data. It has the following members. (1=Tripped); Drive Sensor is open/short circuit SSW_FLAGS_Bit7_S2_Conn_FLT BOOL Module Flags - Sensor 2 connection fault (1=Tripped); Idler Sensor is open/short circuit SSW_FLAGS_Bit8_Slip_Trip BOOL Module Flags - Slip trip (1=Tripped); The difference between belt and drive speed > slip trip margin setting. SSW_FLAGS_Bit9_UO_Speed_Err BOOL Module Flags - Idle roller Under/Over speed (1=Tripped); Belt speed is outside the under/over speed margin setting. SSW_FLAGS_Bit10_Internal_Error BOOL Module Flags - SSW internal error (1=Tripped); EEPROM Error (checked at node power-up) SSW_FLAGS_Bit13_Slip_Inh_TMR BOOL Module Flags - Slip trip inhibit timer (1=Active); Reload and timer start on MC 0 -> 1 SSW_FLAGS_Bit14_UO_Inh_TMR BOOL Module Flags - Under/Over trip inhibit timer (1=Active); Reload and timer start on MC 0 -> 1 SSW_FLAGS_Bit15_Sensor_Num BOOL Module Flags - Number of sensors; 0=1 sensor (Only an idler sensor exists.); 1=2 sensors (There is both a drive and an idler sensor). SSW_FLAGS_Status iMac_STATUS_DT Module Status SSW_FLAGS_Resist INT Module Resistance Value SSW_FLAGS_Errors iMac_ERROR_DT Module Error Counters Member Name Data Type Description SSW_Value INT Module Register Value SSW_Value_Status iMac_STATUS_DT Module Status SSW_Value_Resist INT Module Resistance Value SSW_Value_Errors iMac_ERROR_DT Module Error Counters

Page 34 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.1.31 iMac_Modules_DT This UDT stores iMAC Module data for all possible types of modules in a network of 256 modules. It has the following members. Member Name Data Type Description AIM_FLAGS_Modules iMac_AIM_FLAGS_ModDT[256] Storage for data from up to 256 of these modules in a network. AIM_AI_Modules iMac_AIM_AI_ModDT[256] Storage for data from up to 256 of these modules in a network. AIM_Power_Modules iMac_AIM_Power_ModDT[256] Storage for data from up to 256 of these modules in a network. DI4_Modules iMac_DI4_ModDT[256] Storage for data from up to 256 of these modules in a network. DI8_Modules iMac_DI8_ModDT[256] Storage for data from up to 256 of these modules in a network. GAI3_FLAGS_Modules iMac_GAI3_FLAGS_ModDT[256] Storage for data from up to 256 of these modules in a network. GAI3_Analog1_Modules iMac_GAI3_AI_ModDT[256] Storage for data from up to 256 of these modules in a network. GAI3_Analog2_Modules iMac_GAI3_AI_ModDT[256] Storage for data from up to 256 of these modules in a network. GAI3_Analog3_Modules iMac_GAI3_AI_ModDT[256] Storage for data from up to 256 of these modules in a network. IIM_Modules iMac_IIM_ModDT[256] Storage for data from up to 256 of these modules in a network. LED4_Modules iMac_LED4_ModDT[256] Storage for data from up to 256 of these modules in a network. RIS_Modules iMac_RIS_ModDT[256] Storage for data from up to 256 of these modules in a network. RO4_Modules iMac_RO4_ModDT[256] Storage for data from up to 256 of these modules in a network. RTD1_FLAGS_Modules iMac_RTD1_FLAGS_ModDT[256] Storage for data from up to 256 of these modules in a network. RTD1_Temp_Modules iMac_RTD_Temp_ModDT[256] Storage for data from up to 256 of these modules in a network.

Page 35 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART RTD3_FLAGS_Modules iMac_RTD3_FLAGS_ModDT[256] Storage for data from up to 256 of these modules in a network. RTD3_Temp1_Modules iMac_RTD_Temp_ModDT[256] Storage for data from up to 256 of these modules in a network. RTD3_Temp2_Modules iMac_RTD_Temp_ModDT[256] Storage for data from up to 256 of these modules in a network. RTD3_Temp3_Modules iMac_RTD_Temp_ModDT[256] Storage for data from up to 256 of these modules in a network. SIM_G_Modules iMac_SIM_G_ModDT[16] Storage for data from up to 16 of these modules in a network. SIM_G2_Modules iMac_SIM_G2_ModDT[16] Storage for data from up to 16 of these modules in a network. SIM_P_Modules iMac_SIM_P_ModDT[128] Storage for data from up to 128 of these modules in a network. SIM_T_Modules iMac_SIM_T_ModDT[16] Storage for data from up to 16 of these modules in a network. SSW_FLAGS_Modules iMac_SSW_FLAGS_ModDT[256] Storage for data from up to 256 of these modules in a network. SSW_Control_Modules iMac_SSW_Control_ModDT[256] Storage for data from up to 256 of these modules in a network. SSW_PC_Slip_Modules iMac_SSW_Value_ModDT[256] Storage for data from up to 256 of these modules in a network. SSW_PC_Speed_Modules iMac_SSW_Value_ModDT[256] Storage for data from up to 256 of these modules in a network. SSW_Linr_Speed_Modules iMac_SSW_Value_ModDT[256] Storage for data from up to 256 of these modules in a network.

Page 36 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART AOIs 4.2 This subsection will describe four RSLogix5000 add-on instructions that have been written for retrieving the EtherNet/IP data from the iMAC2. Instruction parameters and logic (where relevant) is to be described. 4.2.1 iMac_Demux_AOI This AOI reads in data from the iMAC2 EIP module assembly instance, and distributes it to iMAC2 bug UDT instances and the iMAC2 Controller UDT instance. It uses a network setup lookup table to determine where the bug data needs to be distributed. The AOI parameters are as follows. Name Usage Data Type Description InputAssembly InOut INT[100] Input assembly data from Ethernet iMac_Network_Config InOut iMac_Network_Config_DT iMAC network configuration lookup table. iMac_Controller InOut iMac_Controller_DT iMAC Controller UDT iMac_Modules InOut iMac_Modules_DT All bug data. The iMac_Demux_AOI InputAssembly input parameter is of the form described earlier in Table 3.1: iMAC2 Controller Input Assembly Instance Data Structure. The AOI logic works in two stages:  In stage 1, the Data, Status, Resistance and ErrCnt data for each of the four consecutive modules (with the first module node address specified in Start Block Address) is stored to the iMac_Controller DATA, STATUS, RESIST and ERROR arrays. The next block of input assembly data is stored to the iMac_Controller Runtime data. Lastly, the General Buffer and NV Memory data is stored to the GENBUFF and NVM arrays. In time, the data for all bugs (modules) will eventually be stored to the iMac_Controller UDT instance.  In stage 2, the iMac_Network_Config parameter is consulted, and when there is a valid module type, the node index is used to transfer the DATA, STATUS, RESIST and ERROR information from the iMac_Controller array (at the node index) to the iMac_Modules UDT instances, according to the module type and index. For example, if there is a DI4 module at node address 7, then iMac_Network_Config[7] = 15 (the module type); data will be transferred from iMac_Controller.DATA[7] to iMac_Modules.DI4_Modules[7].DI4_Inputs_IPx, and so on for the STATUS[7], RESIST[7] and ERROR[7] data. 4.2.2 iMac_Clear_Data_AOI This AOI clears all iMAC2 module and controller instance data. It is intended to be used on first scan only. The AOI parameters are as follows. Name Usage Data Type Description iMac_Controller InOut iMac_Controller_DT iMAC Controller UDT iMac_Modules InOut iMac_Modules_DT All bug data.

Page 37 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART 4.2.3 iMac_Errors_Assign_AOI This AOI Assigns iMAC module errors to all types of iMAC modules. It is used within iMac_Demux_AOI as a repeatable function call, to make code more readable and compact. The AOI parameters are as follows. Name Usage Data Type Description iMac_Module_Errors InOut iMac_ERROR_DT iMAC Module status word iMac_Controller_Error Input INT iMAC Status Word read in from controller 4.2.4 iMac_Status_Assign_AOI This AOI assigns iMAC module status bit definitions to all types of iMAC modules. It is used within iMac_Demux_AOI and iMac_Clear_Data_AOI as a repeatable function call, to make code more readable and compact. The AOI parameters are as follows. Name Usage Data Type Description iMac_Module_Status InOut iMac_STATUS_DT iMAC Module status word iMac_Controller_Status Input INT iMAC Status Word read in from controller RSLogix5000 Program/Routine Usage 4.3 The minimum Program/Routine requirements for getting iMAC2 EtherNet/IP data in RSLogix5000 are shown in Figure 5. They are:  Creation of a Generic Ethernet Module in the RSLogix5000 I/O Configuration tree. This is shown in Figure 6.  Tags for loading, configuring and storing the iMAC2 data. The tags shown in Figure 5 include: o Imac:I.Data, the Assembly Instance tag, which is automatically generated by RSLogix5000 when the Ethernet module is created. o IMAC_Network, the instance of iMac_Network_Config_DT for entering the iMAC2 network configuration lookup table. o IMAC_Control, the instance of iMac_Controller_DT for storing the data read from the iMAC2 network, which is the iMAC2 Controller data and the raw modules data. o IMAC_Modules_all, the instance of iMac_Modules_DT for storing the module data in more readable and accessible form.  A call to a routine to clear all the iMAC2 EIP data instances. This routine should use the iMac_Clear_Data_AOI, and need only be called at first scan.  A call to a routine to set up the network configuration for the iMAC2 module network. This routine should contain instructions for assigning module types at their node addresses; e.g. if a DI4 module (type = 15) is at node address 7, then use IMAC_Network.Lookup_Table[7].Module_Type := 15;  Lastly, a call to an iMac_Demux_AOI instance to read EtherNet/IP data and distribute it to the iMAC2 Controller and Modules tags, based on the iMAC2 Network setup.

Page 38 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART Figure 5: Minimum Program/Routine requirements for getting iMAC2 EtherNet/IP data in RSLogix5000 Figure 6: Generic Ethernet Module setup for iMAC2 EIP data. If there is a SIM-G, SIM-G2, SIM-P or SIM-T module in the iMAC2 network, this needs setting up in a more complex way because it takes up 16 consecutive node addresses (or 17 for a SIM-P module). Additional network configuration data is used to specify the SIM-G/SIM-G2/SIM-P/SIM-T unit number and the sub- index of the node within the 16 (or 17) consecutive node addresses. This is better explained with an example of SIM-G data setup as follows:

Page 39 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART IMAC_Network.Lookup_Table[node address].Module_Type := 37; // SIM-G type IMAC_Network.Lookup_Table[node address].Module_Type_Data1 := unit_number; //0 to 15 IMAC_Network.Lookup_Table[node address].Module_Type_Data2 := 0; IMAC_Network.Lookup_Table[node address+1].Module_Type := 37; // SIM-G type IMAC_Network.Lookup_Table[node address+1].Module_Type_Data1 := unit_number; //0 to 15 IMAC_Network.Lookup_Table[node address+1].Module_Type_Data2 := 1; IMAC_Network.Lookup_Table[node address+2].Module_Type := 37; // SIM-G type IMAC_Network.Lookup_Table[node address+2].Module_Type_Data1 := unit_number; //0 to 15 IMAC_Network.Lookup_Table[node address+2].Module_Type_Data2 := 2; and so on to IMAC_Network.Lookup_Table[node address+15].Module_Type := 37; // SIM-G type IMAC_Network.Lookup_Table[node address+15].Module_Type_Data1 := unit_number; //0 to 15 IMAC_Network.Lookup_Table[node address+15].Module_Type_Data2 := 15; Example Setup 4.4 This example is based on the iMAC2 Demonstration Box shown in Figure 7. Figure 7: iMAC2 Demonstration Box

Page 40 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART It has three modules – an AIM module, a DI4 module and an RTD1 module. When running, the web interface shows the online modules as in Figure 8. The modules and addresses are as follows:  iMAC address 10: EOL module.  iMAC address 20: DI4 module.  iMAC address 28: AIM_FLAGS module.  iMAC address 29: AIM_AI module.  iMAC address 30: AIM_Power module.  iMAC address 40: RTD1_FLAGS module.  iMAC address 41: RTD1_Temp module.  iMAC address 96: MEOL module. In RSLogix5000, this network information is entered as follows: IMAC_Network.Lookup_Table[20].Module_Type := 15; // DI4 type IMAC_Network.Lookup_Table[28].Module_Type := 48; // AIM_FLAGS type IMAC_Network.Lookup_Table[29].Module_Type := 49; // AIM_AI type IMAC_Network.Lookup_Table[30].Module_Type := 50; // AIM_Power type IMAC_Network.Lookup_Table[40].Module_Type := 54; // RTD1_FLAGS type IMAC_Network.Lookup_Table[41].Module_Type := 55; // RTD1_Temp_Input type Figure 8: iMAC web interface online modules.

Page 41 of 41 Ampcontrol Pty Ltd – ABN 28 000 915 542 iMAC2 Controller EtherNet/IP Communications Manual IMAC2B015 V2 – 07/17 APPROVED FOR EXTERNAL DISTRIBUTION – PROPERTY OF AMPCONTROL PTY LTD – NOT TO BE REPRODUCED IN PART When the PLC code is running, the iMAC2 data will be retrieved from the EIP instance and will be distributed to the module arrays as needed. For example, the AIM Power module at node address 30 will have its data inserted into IMAC_Modules_all.AIM_Power_Modules[30] - Figure 9 shows the Power supply data (24.22V) and resistance value (93 ohms) transferred correctly. Figure 9: Node 30 data transferred to the PLC. Once the iMAC2 data is transferred to the PLC correctly, it can easily be referenced and used in the automation project via aliasing, or via direct tag references such as: Important_Input_Bool := IMAC_Modules_all.DI8_Modules[7].DI8_Inputs_IP3