Amprobe AMP-25 Operation & User’s Manual

Temperature Coefficient nominal 0.2 x (specified accuracy)/ °C , <18°C, >28°C) Transient Protection 6.0 kV (1.2/50 µs surge) E.M.C. Meets IEC/EN 61326-1 Safety Compliance IEC/EN 61010-1, IEC/EN 61010-2-032 Agency Approval ) P Shock Vibration MIL-PRF-28800F for A class 2 instrument Drop-Proof 4 feet (120 cm) Power Supply Two 1.5V LR44 size battery Battery Life 20 hours Low Battery Indication Auto Power Off Idle for 20 minutes Dimension (L x W x H) 5.8 x 2.4x 1.3 in (147 x 60 x 32 mm) Weight 140 g (0.31 lb) Jaw Opening & Conductor Diameter ...

3 Jaw Trigger 4 LCD Display 5 Indicator of the Jaw Center for Current Measurement 6 Backlight / Flashlight & Function Buttons AMP-25 / AMP-25-EUR Mini-Clamp AMP-25 ZERO 2 Sec TRMS AC / 1 2 4 3 5 6 ...

W Warning To avoid electrical shock and injury: •� Do not hold the Meter anywhere beyond the tactile barrier. •� Do not use the Meter to measure currents above the maximum rated frequency (400Hz). Circulating currents may cause the magnetic circuits of the Jaws reach hazardous excessive temperatures. To measure AC or DC current: 1. Switch on the Meter by pressing button, the default is auto AC/DC A detection mode (AUTO is displayed). Press button to choose AC A or DC A. The display reflects the chosen function mode. 2. Open the clamp by pressing the j ...

meter should be performed only by a Factory Authorized Service Center or by other qualified instrument service personnel. The front panel and case can be cleaned with a mild solution of detergent and water. Apply sparingly with a soft cloth and allow to dry completely before using. Do not use aromatic hydrocarbons, gasoline or chlorinated solvents for cleaning. BATTERY REPLACEMENT When battery voltage drops below the value required for proper operation, the battery symbol ( ) appears. W Warning To avoid shock, injury, or damage to ...

Range 60.00 A 300.0 A Resolution 0.01 A 0.1 A Accuracy 50 Hz to 60 Hz ± (3.5 % + 25 LSD) at < 3 A ± (3.5 % + 5 LSD) at ≥ 3 A ± (3.5 % + 5 LSD) Cut-off Frequency (-3dB): Approx. 160 Hz Attenuation Characteristic: Approx. -24 dB/Octave Inrush Current Range 300.0 A Resolution 0.1 A CIntegration Time: 100 ms Trigger Current: 5.0 A Non-Contact Voltage Detection Voltage range: 80 V to 600 V, 50 Hz to 60 Hz Indication: bar-graph segments and audible beep tones proportional to the field strength Detection frequency: 50/60 Hz Detection antenna: inside the top side of the station ...

the Meter before use. Look for cracks or missing plastic. Pay particular attention to the insulation around the connectors. •� Have the Meter serviced only by qualified service personnel. •� Use extreme caution when working around bare conductors or bus bars. Contact with the conductor could result in electric shock. •� Do not hold the Meter anywhere beyond the tactile barrier. •� When measuring current, center the conductor in the clamp. •� Never operate the Meter with the battery cover removed or the case open. ...

Press and hold button while pressing button. “AoFF” is displayed, then release and button. The meter is turned ON and goes into default measurement function (auto AC/DC A). The auto power off mode resumes back when the Meter is OFF and is turned ON again. SPECIFICATIONS Display 6000 counts Sensing True-RMS Polarity Automatic Over-Range Display “OL” or “-OL” Update Rate 2 times per second nominal Operating Temperature 32 °F to 122 °F (0 °C to 50 °C) Relative Humidity Non-condensing, 32 °F to 86 °F (0 °C to 30 °C) ≤ 80%, >86 °F to 104 °F (>3 ...