Anritsu MS2830A Operation Manual

ANRITSU CORPORATION MS2830A Signal Analyzer Operation Manual Mainframe Operation For safety and warning information, please read this manual before attempting to use the equipment. Keep this manual with the equipment. 32nd Edition

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this manual. Symbols used in manual This indicates a very dangerous procedure that could result in serious injury or death if not performed properly. This indicates a hazardous procedure that could result in serious injury or death if not performed properly. This indicates a hazardous procedure or danger that could result in light-to-severe injury, or loss related to equipment malfunction, if proper precautions are not taken. Safety Symbols Used on Equipment and in Manual The following safety symbols are used inside or on the equipment near operation locations to provide information about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and take the necessary precautions BEFORE using the equipment. This indicates a prohibited operation. The prohibited operation is indicated symbolically in or near the barred circle. This indicates an obligatory safety precaution. The obligatory operation is indicated symbolically in or near the circle. This indicates a warning or caution. The contents are indicated symbolically in or near the triangle. This indicates a note. The contents are described in the box. These indicate that the marked part should be recycled. MS2830A Signal Analyzer Operation Manual Mainframe Operation 15 December 2009 (First Edition) 20 April 2017 (32nd Edition) Copyright © 2009-2017, ANRITSU CORPORATION. All rights reserved. No part of this manual may be reproduced without the prior written permission of the publisher. The contents of this manual may be changed without prior notice. Printed in Japan DANGER WARNING CAUTION

with the correct polarity. If the wrong battery is used, or if the battery is inserted with reversed polarity, there is a risk of explosion causing severe injury or death. ● DO NOT expose batteries to heat or fire. This is dangerous and can result in explosions or fire. Heating batteries may cause them to leak or explode. WARNING ● ALWAYS refer to the operation manual when working near locations at which the alert mark shown on the left is attached. If the advice in the operation manual is not followed there is a risk of personal injury or reduced equipment performance. The alert mark shown on the left may also be used with other marks and descriptions to indicate other dangers. ● Overvoltage Category This equipment complies with overvoltage category II defined in IEC 61010. DO NOT connect this equipment to the power supply of overvoltage category III or IV. ● To ensure that the equipment is grounded, always use the supplied 3-pin power cord, and insert the plug into an outlet with a ground terminal. If power is supplied without grounding the equipment, there is a risk of receiving a severe or fatal electric shock or causing damage to the internal components. Electric Shock Replacing Battery Battery Disposal

shock hazards should service this equipment. This equipment cannot be repaired by the operator. DO NOT attempt to remove the equipment covers or unit covers or to disassemble internal components. There are high-voltage parts in this equipment presenting a risk of severe injury or fatal electric shock to untrained personnel. In addition, there is a risk of damage to precision components. ● The performance-guarantee seal verifies the integrity of the equipment. To ensure the continued integrity of the equipment, only Anritsu service personnel, or service personnel of an Anritsu sales representative, should break this seal to repair or calibrate the equipment. Be careful not to break the seal by opening the equipment or unit covers. If the performance-guarantee seal is broken by you or a third party, the performance of the equipment cannot be guaranteed. Repair Calibration

the cabinet is turned on its side, etc., it will be unstable and may be damaged if it falls over as a result of receiving a slight mechanical shock. Always set up the equipment in a position where the power switch can be reached without difficulty. ● DO NOT short the battery terminals and never attempt to disassemble the battery or dispose of it in a fire. If the battery is damaged by any of these actions, the battery fluid may leak. This fluid is poisonous. DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is accidentally ingested, spit it out immediately, rinse your mouth with water and seek medical help. If it enters your eyes accidentally, do not rub your eyes, rinse them with clean running water and seek medical help. If the liquid gets on your skin or clothes, wash it off carefully and thoroughly with clean water. ● This equipment uses a Liquid Crystal Display (LCD). DO NOT subject the equipment to excessive force or drop it. If the LCD is subjected to strong mechanical shock, it may break and liquid may leak. This liquid is very caustic and poisonous. DO NOT touch it, ingest it, or get in your eyes. If it is ingested accidentally, spit it out immediately, rinse your mouth with water and seek medical help. If it enters your eyes accidentally, do not rub your eyes, rinse them with clean running water and seek medical help. If the liquid gets on your skin or clothes, wash it off carefully and thoroughly with soap and water. Falling Over LCD Battery Fluid

cleaning dust around the power supply and fan. • Clean the power inlet regularly. If dust accumulates around the power pins, there is a risk of fire. • Keep the cooling fan clean so that the ventilation holes are not obstructed. If the ventilation is obstructed, the cabinet may overheat and catch fire. ● Never input a signal of more than the indicated value between the measured terminal and ground. Input of an excessive signal may damage the equipment. Cleaning Check Terminal

the memory. This battery must be replaced by service personnel when it has reached the end of its useful life; contact the Anritsu sales section or your nearest representative. Note: The battery used in this equipment has a maximum useful life of 7 years. It should be replaced before this period has elapsed. This equipment uses USB memory stick as external storage media for storing data and programs. If this media is mishandled or becomes faulty, important data may be lost. It is recommended to periodically back up all important data and programs to protect them from being lost accidentally. Anritsu will not be held responsible for lost data. Pay careful attention to the following points. ● Never remove the USB memory stick from the equipment while it is being accessed. ● The USB memory stick may be damaged by static electric charges. ● Anritsu has thoroughly tested all external storage media shipped with this equipment. Users should note that external storage media not shipped with this equipment may not have been tested by Anritsu, thus Anritsu cannot guarantee the performance or suitability of such media. Replacing Memory Back-up Battery External Storage Media

with any hard disk, data may be lost under certain conditions. It is recommended to periodically back up all important data and programs to protect them from being lost accidentally. Anritsu will not be held responsible for lost data. To reduce the possibility of data loss, particular attention should be given to the following points. ● The equipment should only be used within the recommend temperature range, and should not be used in locations where the temperature may fluctuate suddenly. ● Always follow the guidelines to ensure that the equipment is set up in the specified manner. ● Always ensure that the fans at the rear and side of the equipment are not blocked or obstructed in any way. ● Exercise care not to bang or shake the equipment whilst the power is on. ● Never disconnect the mains power at the plug or cut the power at the breaker with the equipment turned on. This equipment is designed for an industrial environment. In a residential environment this equipment may cause radio interference in which case the user may be required to take adequate measures. Exposure to corrosive gases such as hydrogen sulfide, sulfurous acid, and hydrogen chloride will cause faults and failures. Note that some organic solvents release corrosive gases. Hard disk Use in a Residential Environment Use in Corrosive Atmospheres

using calibrated measuring instruments with direct traceability to public testing organizations recognized by national research laboratories, including the National Institute of Advanced Industrial Science and Technology, and the National Institute of Information and Communications Technology, and was found to meet the published specifications. Anritsu Warranty Anritsu Corporation will repair this equipment free-of-charge if a malfunction occurs within one year after shipment due to a manufacturing fault. However, software fixes will be made in accordance with the separate Software End-User License Agreement. Moreover, Anritsu Corporation will deem this warranty void when: ● The fault is outside the scope of the warranty conditions separately described in the operation manual. ● The fault is due to mishandling, misuse, or unauthorized modification or repair of the equipment by the customer. ● The fault is due to severe usage clearly exceeding normal usage. ● The fault is due to improper or insufficient maintenance by the customer. ● The fault is due to natural disaster, including fire, wind, flooding, earthquake, lightning strike, or volcanic ash, etc. ● The fault is due to damage caused by acts of destruction, including civil disturbance, riot, or war, etc. ● The fault is due to explosion, accident, or breakdown of any other machinery, facility, or plant, etc. ● The fault is due to use of non-specified peripheral or applied equipment or parts, or consumables, etc. ● The fault is due to use of a non-specified power supply or in a non-specified installation location. ● The fault is due to use in unusual environments(Note). ● The fault is due to activities or ingress of living organisms, such as insects, spiders, fungus, pollen, or seeds. In addition, this warranty is valid only for the original equipment purchaser. It is not transferable if the equipment is resold. Anritsu Corporation shall assume no liability for injury or financial loss of the customer due to the use of or a failure to be able to use this equipment.

● In places of direct sunlight ● In dusty places ● Outdoors ● In liquids, such as water, oil, or organic solvents, and medical fluids, or places where these liquids may adhere ● In salty air or in place chemically active gases (sulfur dioxide, hydrogen sulfide, chlorine, ammonia, nitrogen oxide, or hydrogen chloride etc.) are present ● In places where high-intensity static electric charges or electromagnetic fields are present ● In places where abnormal power voltages (high or low) or instantaneous power failures occur ● In places where condensation occurs ● In the presence of lubricating oil mists ● In places at an altitude of more than 2,000 m ● In the presence of frequent vibration or mechanical shock, such as in cars, ships, or airplanes Anritsu Corporation Contact In the event that this equipment malfunctions, contact an Anritsu Service and Sales office. Contact information can be found on the last page of the printed version of this manual, and is available in a separate file on the PDF version.

Please read this Software End-User License Agreement (hereafter this EULA) carefully before using (includes executing, copying, registering, etc.) this software (includes programs, databases, scenarios, etc., used to operate, set, etc., Anritsu electronic equipment). By reading this EULA and using this software, you are agreeing to be bound by the terms of its contents and Anritsu Corporation (hereafter Anritsu) hereby grants you the right to use this Software with the Anritsu-specified equipment (hereafter Equipment) for the purposes set out in this EULA. 1. Grant of License and Limitations 1. Regardless of whether this Software was purchased from or provided free-of-charge by Anritsu, you agree not to rent, lease, lend, or otherwise distribute this Software to third parties and further agree not to disassemble, recompile, reverse engineer, modify, or create derivative works of this Software. 2. You may make one copy of this Software for backup purposes only. 3. You are not permitted to reverse engineer this software. 4. This EULA allows you to install one copy of this Software on one piece of Equipment. 2. Disclaimers To the extent not prohibited by law, in no event shall Anritsu be liable for personal injury, or any incidental, special, indirect or consequential damages whatsoever, including, without limitation, damages for loss of profits, loss of data, business interruption or any other commercial damages or losses, arising out of or related to your use or inability to use this Software. 3. Limitation of Liability a. If a fault (bug) is discovered in this Software, preventing operation as described in the operation manual or specifications whether or not the customer uses this software as described in the manual, Anritsu shall at its own discretion, fix the bug, or exchange the software, or suggest a workaround, free-of-charge. However, notwithstanding the above, the following items shall be excluded from repair and warranty. i) If this Software is deemed to be used for purposes not described in the operation manual or specifications. ii) If this Software is used in conjunction with other non-Anritsu-approved software. iii) Recovery of lost or damaged data. iv) If this Software or the Equipment has been modified, repaired, or otherwise altered without Anritsu's prior approval. v) For any other reasons out of Anritsu's direct control and responsibility, such as but not limited to, natural disasters, software virus infections, etc. b. Expenses incurred for transport, hotel, daily allowance, etc., for on-site repairs by Anritsu engineers necessitated by the above faults shall be borne by you. c. The warranty period for faults listed in article 3a above covered by this EULA shall be either 6 months from the date of purchase of this Software or 30 days after the date of repair, whichever is longer.

You may not use or otherwise export or re-export directly or indirectly this Software except as authorized by Japanese and United States law. In particular, this software may not be exported or re-exported (a) into any Japanese or US embargoed countries or (b) to anyone on the Japanese or US Treasury Department's list of Specially Designated Nationals or the US Department of Commerce Denied Persons List or Entity List. By using this Software, you warrant that you are not located in any such country or on any such list. You also agree that you will not use this Software for any purposes prohibited by Japanese and US law, including, without limitation, the development, design and manufacture or production of missiles or nuclear, chemical or biological weapons of mass destruction. 5. Termination Anritsu shall deem this EULA terminated if you violate any conditions described herein. This EULA shall also be terminated if the conditions herein cannot be continued for any good reason, such as violation of copyrights, patents, or other laws and ordinances. 6. Reparations If Anritsu suffers any loss, financial or otherwise, due to your violation of the terms of this EULA, Anritsu shall have the right to seek proportional damages from you. 7. Responsibility after Termination Upon termination of this EULA in accordance with item 5, you shall cease all use of this Software immediately and shall as directed by Anritsu either destroy or return this Software and any backup copies, full or partial, to Anritsu. 8. Dispute Resolution If matters of dispute or items not covered by this EULA arise, they shall be resolved by negotiations in good faith between you and Anritsu. 9. Court of Jurisdiction This EULA shall be interpreted in accordance with Japanese law and any disputes that cannot be resolved by negotiation described in Article 8 shall be settled by the Japanese courts.

for Remote Control of This Equipment When controlling this measuring equipment remotely using the Ethernet port, a VISA*1 driver must be installed in the PC controller. We recommend using NI-VISA™*2 from National Instruments™ (NI hereafter) as the VISA driver. Although a license is generally required to use NI-VISA™, the licensed NI-VISA™ driver is provided free-of-charge for use when performing remote control (Note) of this measuring equipment. The NI-VISA™ driver can be downloaded from the NI website at: http://sine.ni.com/psp/app/doc/p/id/psp-411 Be sure to comply with the NI license agreement for the usage and license scope. Be sure to uninstall the NI-VISA™ driver when disposing of this measuring equipment or transferring it to a third party, etc., when ceasing to use NI-VISA™, or upon completion of the contract term when using this equipment on a rental contract. (Notes) Although the NI-VISA™ driver itself can be downloaded free-of-charge from the web, an implementation license is required for legal reasons when some requirements are not met. (Check the NI web page for the detailed requirements.) If these requirements are not met, permission is not granted to use NI hardware and software and an NI implementation license must be purchased. However, since this measuring equipment incorporates NI hardware (GPIB ASIC), the NI-VISA™ driver can be downloaded and used free-of-charge. Glossary of Terms: *1: VISA: Virtual Instrument Software Architecture I/O software specification for remote control of measuring instruments using interfaces such as GPIB, Ethernet, USB, etc. *2: NI-VISA™ World de facto standard I/O software interface developed by NI and standardized by the VXI Plug&Play Alliance. Trademarks: - National Instruments™, NI™, NI-VISA™ and National Instruments Corporation are all trademarks of National Instruments Corporation.

This product and its manuals may require an Export License/Approval by the Government of the product's country of origin for re-export from your country. Before re-exporting the product or manuals, please contact us to confirm whether they are export-controlled items or not. When you dispose of export-controlled items, the products/manuals need to be broken/shredded so as not to be unlawfully used for military purpose. Trademark and Registered Trademark IQproducerTM is a registered trademark of Anritsu Corporation in the United States and/or other countries. Lifetime of Parts The life span of certain parts used in this instrument is determined by the operating time or the power-on time. Due consideration should be given to the life spans of these parts when performing continuous operation over an extended period. These parts must be replaced at the customer's expense even if within the guaranteed period described in Warranty at the beginning of this manual. For details on life span, refer to the corresponding section in this manual. Example: Display backlight, internal hard disk, removable hard disk, connector for hard disk, cooling fan

● Copying files and data Only files that have been provided directly from Anritsu or generated using Anritsu equipment should be copied to the instrument. All other required files should be transferred by means of USB or CompactFlash media after undergoing a thorough virus check. ● Adding software Do not download or install software that has not been specifically recommended or licensed by Anritsu. ● Network connections Ensure that the network has sufficient anti-virus security protection in place.

Equipment marked with the Crossed-out Wheeled Bin Symbol complies with council directive 2012/19/EU (the “WEEE Directive”) in European Union. For Products placed on the EU market after August 13, 2005, please contact your local Anritsu representative at the end of the product's useful life to arrange disposal in accordance with your initial contract and the local law.

Anritsu affixes the CE Conformity marking on the following product(s) in accordance with the Decision 768/2008/EC to indicate that they conform to the EMC and LVD directive of the European Union (EU). CE marking 1. Product Model Model: MS2830A Signal Analyzer 2. Applied Directive EMC: Directive 2014/30/EU LVD: Directive 2014/35/EU 3. Applied Standards ● EMC: Emission: EN 61326-1: 2013 (Class A) Immunity: EN 61326-1: 2013 (Table 2) Performance Criteria* IEC 61000-4-2 (ESD) B IEC 61000-4-3 (EMF) A IEC 61000-4-4 (Burst) B IEC 61000-4-5 (Surge) B IEC 61000-4-6 (CRF) A IEC 61000-4-8 (RPFMF) A IEC 61000-4-11 (V dip/short) B, C *: Performance Criteria A: The equipment shall continue to operate as intended during and after the test. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, either of these may be derived from the product description and documentation and what the user may reasonably expect from the equipment if used as intended.

after the test. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is however allowed. No change of actual operating state or stored data is allowed. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, either of these may be derived from the product description and documentation and what the user may reasonably expect from the equipment if used as intended. C: Temporary loss of function is allowed, provided the function is self-recoverable or can be restored by the operation of the controls. Harmonic current emissions: EN 61000-3-2: 2006 +A1:2009 A2:2009 (Class A equipment) ● LVD: EN 61010-1: 2010 (Pollution Degree 2) 4. Authorized representative Name: Murray Coleman Head of Customer Service EMEA ANRITSU EMEA Ltd. Address, city: 200 Capability Green, Luton Bedfordshire, LU1 3LU Country: United Kingdom

Anritsu affixes the RCM mark on the following product(s) in accordance with the regulation to indicate that they conform to the EMC framework of Australia/New Zealand. RCM marking 1. Product Model Model: MS2830A Signal Analyzer 2. Applied Standards EMC:Emission: EN 61326-1: 2013 (Class A equipment)

The label shown on the left is attached to Anritsu products meeting our environmental standards. Details about this label and the environmental standards are available on the Anritsu website at http://www.anritsu.com

 Associated Documents The operation manual configuration of the MS2830A Signal Analyzer is shown below. MS2690A/MS2691A/MS2692A Signal Analyzer Operation Manual (Main Frame Operation) MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Phase Noise Measurement Function Operation) MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control) MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Main Frame Remote Control) MS2840A Signal Analyzer Operation Manual (Main Frame Operation) Or MS2830A Signal Analyzer Operation Manual (Main Frame Operation) MS2690A/MS2691A/MS2692A Signal Analyzer Operation Manual (Signal Analyzer Function Operation) MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control) MS2830A/MS2840A Signal Analyzer Operation Manual (Signal Analyzer Function Operation) Or MS2690A/MS2691A/MS2692A Spectrum Analyzer Operation Manual (Spectrum Analyzer Function Operation) MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control) MS2830A/MS2840A Spectrum Analyzer Operation Manual (Spectrum Analyzer Function Operation) Or

• Signal Analyzer Operation Manual (Mainframe Remote Control) Description of basic operations, maintenance procedures, common functions and common remote functions of the mainframe • Signal Analyzer Operation Manual (Signal Analyzer Function) • Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control) Description of basic operations, functions and remote functions of the signal analyzer • Signal Analyzer Operation Manual (Spectrum Analyzer Function) • Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control) Description of basic operations, functions and remote functions of the spectrum analyzer • Signal Analyzer Operation Manual (Phase Noise Measurement Function) • Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control) Description of basic operations, common functions and common remote functions of the Phase Noise Measurement function In this document, indicates a panel key.

For Safety ................................................... iii About This Manual ....................................... I Overview .......................................... 1-1 Chapter 1 1.1 Product Overview ......................................................... 1-3 1.2 Product Configuration ................................................... 1-4 1.3 Specifications .............................................................. 1-11 Before Use ....................................... 2-1 Chapter 2 2.1 Installation Location ...................................................... 2-2 2.2 Items to Check Before Use ........................................... 2-4 2.3 Power Connection ........................................................ 2-9 Common Operations ....................... 3-1 Chapter 3 3.1 Part Names ................................................................... 3-2 3.2 Turning Power On/Off ................................................. 3-11 3.3 Auto Calibration .......................................................... 3-13 3.4 Settings on Configuration Screen ............................... 3-16 3.5 Loading, Unloading, and Switching Applications ........ 3-33 3.6 Save and Recall Functions ......................................... 3-42 3.7 Initializing .................................................................... 3-51 3.8 Installing and Uninstalling ........................................... 3-53 Chapter 4 Tutorial ............................................. 4-1 4.1 Spectrum Analysis Using Signal Analyzer .................... 4-2 4.2 Spectrum Analysis Using Spectrum Analyzer .............. 4-6 System .............................................. 5-1 Chapter 5 5.1 Setting Windows ........................................................... 5-2

5.3 System Recovery Functions ....................................... 5-10 Performance Test ............................ 6-1 Chapter 6 6.1 Overview of Performance Test ..................................... 6-2 6.2 Performance Test Items ............................................... 6-5 Power Meter ..................................... 7-1 Chapter 7 7.1 Power Meter .................................................................. 7-2 7.2 Display Description ....................................................... 7-3 7.3 Function Menu .............................................................. 7-5 7.4 Initialization ................................................................. 7-15 BER Measurement Function ........... 8-1 Chapter 8 8.1 Outline of BER Measurement ....................................... 8-2 8.2 Display Description ....................................................... 8-5 8.3 BER Measurement Function Menu............................... 8-9 8.4 Connecting MS2830A-026/126 to External System ... 8-11 8.5 Performing BER Measurement ................................... 8-12 8.6 Setting Automatic Resynchronization Function .......... 8-22 8.7 Setting Input Interface ................................................. 8-27 8.8 Setting PN_Fix Pattern ............................................... 8-28 8.9 Setting User-defined Pattern ...................................... 8-34 8.10 Description of BER Measurement Operation ............. 8-42 Maintenance ..................................... 9-1 Chapter 9 9.1 Daily Maintenance and Storage.................................... 9-2 9.2 Repackaging and transporting when returning product ......... 9-4 9.3 Calibration ....................................................................... 9-5

Appendix B Panel Keys and Keyboard Operations .......................................B-1 Appendix C Virus Check Procedure (WES 2009) ....................................C-1 Appendix D Virus Check Procedure (WES 7) ..D-1 Appendix E Error Messages ............................ E-1 Appendix F Initial Value List ............................ F-1 Index .......................................................... Index-1

product configuration. 1.1 Product Overview ......................................................... 1-3 1.2 Product Configuration ................................................... 1-4 1.2.1 Standard configuration ..................................... 1-4 1.2.2 Options ............................................................. 1-5 1.2.3 Applicable Parts ................................................ 1-8 1.2.4 Application Software ....................................... 1-10 1.3 Specifications .............................................................. 1-11 1.3.1 Mainframe (MS2830A) ................................... 1-11 1.3.2 Rubidium Reference Oscillator Option (MS2830A-001/101) ....................................... 1-54 1.3.3 High Stability Reference Oscillator Option (MS2830A-002/102) ....................................... 1-54 1.3.4 Preamplifier Option (MS2830A-008/108) ....... 1-55 1.3.5 Analysis Bandwidth Extension to 31.25 MHz Option (MS2830A-005/105) ......................... 1-56 1.3.6 Analysis Bandwidth Extension to 10 MHz Option (MS2830A-006/106) ......................... 1-56 1.3.7 Phase Noise Measurement Option (MS2830A-010/110) ....................................... 1-56 1.3.8 Secondary HDD Option (MS2830A-011/111) 1-56 1.3.9 Precompliance EMI Function (MS2830A-016/116) ....................................... 1-56 1.3.10 Low Phase Noise Performance Option (MS2830A-062/066) ....................................... 1-57 1.3.11 Removable HDD option (MS2830A-313) ....... 1-58 1.3.12 Microwave Preamplifier Option (MS2830A-068/168) ....................................... 1-59 1.3.13 Microwave Preselector Bypass Option (MS2830A-067/167) ....................................... 1-60 1.3.14 Bandwidth Extension to 31.25 MHz with Preselector Bypass Option (MS2830A-007) 1-62 1.3.15 Analysis Bandwidth Extension Option, 62.5 MHz (MS2830A-077/177) .................... 1-63 1.3.16 Analysis Bandwidth Extension Option, 125 MHz (MS2830A-078/178) ..................... 1-64 1.3.17 Bandwidth Extension to 31.25 MHz for Millimeter-wave (MS2830A-009/109) .......... 1-64 1.3.18 BER Measurement function (MS2830A-026/126) ....................................... 1-65 1.3.19 Audio Analyzer Option (MS2830A-018/118) .. 1-66

1-2 1.3.20 Two-handle Frame with Connecting Parts (for Single-handle Frame) (MS2830A-171) ........ 1-66 1.3.21 Connecting parts (for two-handle frame) (MS2830A-081/181) ....................................... 1-66 1.3.22 3.6 GHz Analog Signal Generator Option (MS2830A-088/188) ....................................... 1-66 1.3.23 Vector Function Extension for Analog Signal Generator Option (MS2830A-189) ................. 1-66 1.3.24 Internal Signal Generator Control Function Option (MS2830A-052/152/352) .................. 1-67

The MS2830A Signal Analyzer ("the MS2830A" hereafter) is a spectrum analyzer to which options such as real-time signal analysis and vector modulation analysis can be added. The MS2830A enables high-speed and high-accuracy signal processing of wide-ranging analyses at full-span, a characteristic of conventional sweep-type spectrum analyzers, using a digital IF block. In addition, the FFT process (high-speed Fourier conversion) realizes high-speed spectrum analysis and simultaneous analysis on frequency and time axes not possible with conventional sweep-type spectrum analyzers. Also, added option enables recording of the RF input signal as digital data (digitize function). It can be used in a variety of applications from research and development to manufacturing thanks to its characteristics. The key features are listed below: ● Wide frequency band (3.6 GHz/6 GHz/13.5 GHz/26.5 GHz/43 GHz) ● Wide analysis bandwidth (Option 006/106: 10 MHz, Option 005/105/007: 31.25 MHz, Option 077/177: 62.5 MHz, Option 078/178: 125 MHz,) ● High dynamic range ● High-speed measurement ● High-speed, high-accuracy signal analysis using digital IF ● Enables time-continuous analysis of loaded data ● Large-capacity waveform memory and digitization function that records RF signals without missing (when option 006/106, 005/105, 007, 077/177, or 078/178 is used) ● BER Measurement function (when option 026/126 is used) ● Rich measurement functions The MS2830A is equipped with the hardware product made by National Instruments and comes with the license for NI-VISA. NI-VISA can be used for the purpose of controlling the MS2830A.

1-4 1.2 Product Configuration 1.2.1 Standard configuration Table 1.2.1-1 lists the standard configuration. At unpacking, check that all items are included. Contact an Anritsu Service and Sales office if any parts are missing or damaged. Table 1.2.1-1 Standard Configuration Items Model Product name Qua ntity Remarks Unit MS2830A Signal Analyzer 1 – Access ories – Power cord 1 P0031A USB memory 1 256MB or more USB 2.0 Flash Driver Z0541A USB Mouse 1 – – Installation CD-ROM 1 Application software, Operation Manual CD-ROM

separately. Note: There is a risk of losing the data when adding additional option(s), so back up the data stored on the hard disk, in advance. Anritsu is not responsible for any loss of data. Table 1.2.2-1 Additional Options at/after shipment Option Number Product Name Remarks MS2830A-040 3.6 GHz Signal Analyzer 9 kHz to 3.6 GHz MS2830A-041 6 GHz Signal Analyzer 9 kHz to 6 GHz MS2830A-043 13.5 GHz Signal Analyzer 9 kHz to 13.5 GHz MS2830A-044 26.5 GHz Signal Analyzer 9 kHz to 26.5 GHz MS2830A-045 43 GHz Signal Analyzer 9 kHz to 43 GHz MS2830A-001 Rubidium Reference Oscillator See Table 1.3.1-1 “Internal reference oscillator”. MS2830A-101 Rubidium Reference Oscillator Retrofit See Table 1.3.1-1 “Internal reference oscillator”. MS2830A-002 High Stability Reference Oscillator See Table 1.3.1-1, “Internal reference oscillator” MS2830A-102 High Stability Reference Oscillator, Retrofit See Table 1.3.1-1, “Internal reference oscillator” MS2830A-006 Analysis Bandwidth 10 MHz Analysis bandwidth: Max. 10 MHz MS2830A-106 Analysis Bandwidth 10 MHz, Retrofit Analysis bandwidth: Max. 10 MHz MS2830A-005 Analysis Bandwidth Extension to 31.25 MHz Extends Analysis Bandwidth to 31.25 MHz MS2830A-105 Analysis Bandwidth Extension to 31.25 MHz, Retrofit Extends Analysis Bandwidth to 31.25 MHz MS2830A-007 Bandwidth Extension to 31.25 MHz with Preselector Bypass Available only when MS2830A-045 is installed. MS2830A-009 Bandwidth Extension to 31.25 MHz for Millimeter-wave Extends Analysis Bandwidth to 31.25 MHz Available only when MS2830A-045 is installed. MS2830A-109 Bandwidth Extension to 31.25 MHz for Millimeter-wave, Retrofit Extends Analysis Bandwidth to 31.25 MHz Available only when MS2830A-045 is installed. MS2830A-077 Analysis Bandwidth Extension to 62.5 MHz Extends Analysis Bandwidth to 62.5 MHz MS2830A-177 Analysis Bandwidth Extension to 62.5 MHz, Retrofit Extends Analysis Bandwidth to 62.5 MHz MS2830A-078 Analysis Bandwidth Extension to 125 MHz Extends Analysis Bandwidth to 125 MHz MS2830A-178 Analysis Bandwidth Extension to 125 MHz, Retrofit Extends Analysis Bandwidth to 125 MHz

1-6 Table 1.2.2-1 Additional Options at/after shipment (Cont’d) Option Number Product Name Remarks MS2830A-008 Preamplifier 100 kHz to 3.6 GHz (With MS2830-040) 100 kHz to 6 GHz (With MS2830-041/043) MS2830A-108 Preamplifier, Retrofit 100 kHz to 3.6 GHz (With MS2830-040) 100 kHz to 6 GHz (With MS2830-041/043) MS2830A-010 Phase Noise Measurement Function 10 MHz to Upper frequency limit MS2830A-110 Phase Noise Measurement Function, Retrofit 10 MHz to Upper frequency limit MS2830A-011 Secondary HDD MS2830A-111 Secondary HDD, Retrofit MS2830A-016 Precompliance EMI Function MS2830A-116 Precompliance EMI Function Retrofit MS2830A-017 Noise Figure Measurement Function MS2830A-117 Noise Figure Measurement Function Retrofit MS2830A-018 Audio Analyzer MS2830A-118 Audio Analyzer Retrofit MS2830A-020 3.6 GHz Vector Signal Generator 250 kHz to 3.6 GHz MS2830A-120 3.6 GHz Vector Signal Generator, Retrofit 250 kHz to 3.6 GHz MS2830A-021 6 GHz Vector Signal Generator 250 kHz to 6 GHz MS2830A-121 6 GHz Vector Signal Generator, Retrofit 250 kHz to 6 GHz MS2830A-022 Low Power Extension for Vector Signal Generator Lower setting limit of output signal level: –136 dBm MS2830A-122 Low Power Extension for Vector Signal Generator, Retrofit Lower setting limit of output signal level: –136 dBm MS2830A-026 BER Measurement function MS2830A-126 BER Measurement function, Retrofit MS2830A-027 ARB Memory Upgrade 256 MSample for Vector Signal Generator MS2830A-127 ARB Memory Upgrade 256 MSample for Vector Signal Generator, Retrofit MS2830A-028 AWGN MS2830A-128 AWGN, Retrofit MS2830A-052 Internal Signal Generator Control Function MS2830A-152 Internal Signal Generator Control Function Retrofit MS2830A-352 Internal Signal Generator Control Function User-installable

Option Number Product Name Remarks MS2830A-062 Low Phase Noise Performance MS2830A-066 Low Phase Noise Performance MS2830A-067 Microwave Preselector Bypass With MS2830A-044/045 installed MS2830A-167 Microwave Preselector Bypass, Retrofit With MS2830A-044/045 installed MS2830A-068 Microwave Preamplifier 100 kHz to 26.5 GHz (With MS2830A-044 installed) 100 kHz to 43 GHz (With MS2830-045 installed) MS2830A-168 Microwave Preamplifier, Retrofit 100 kHz to 26.5 GHz (With MS2830A-044 installed) 100 kHz to 43 GHz (With MS2830-045 installed) MS2830A-180 CPU/Windows7 64bit Upgrade, Retrofit Upgrade CPU and OS to Windows7 64 bit. MS2830A-171 Two-handle Frame with Connecting Parts (for Single-handle Frame) Retrofit MS2830A-081 Connecting parts (for two-handle frame) MS2830A-181 Connecting parts (for two-handle frame) Retrofit MS2830A-088 3.6GHz Analog Signal Generator MS2830A-188 3.6GHz Analog Signal Generator Retrofit MS2830A-189 Vector Function Extension for Analog Signal Generator Retrofit MS2830A-313 Removable HDD Table 1.2.2-2 Optional Warranty Extension (MS2830A) Option Number Product Name Remarks MS2830A-ES210 2-year Warranty Service – MS2830A-ES310 3-year Warranty Service – MS2830A-ES510 5-year Warranty Service –

1-8 1.2.3 Applicable Parts Table 1.2.3-1 lists the application parts. They are sold separately. Table 1.2.3-1 Applicable Parts Model Number Product Name Remarks W3334AE MS2830A Signal Analyzer Operation Manual (Mainframe Operation) Printed version W2851AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Mainframe Remote Control) Printed version W3335AE MS2830A/MS2840A Signal Analyzer Operation Manual (Signal Analyzer Function Operation) Printed version W2853AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control) Printed version W3336AE MS2830A/MS2840A Signal Analyzer Operation Manual (Spectrum Analyzer Function Operation) Printed version W2855AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control) Printed version W3117AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Phase Noise Measurement Function Operation) Printed version W3118AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control) Printed version W3337AE MS2830A/MS2840A Signal Analyzer Vector Signal Generator Operation Manual (Operation) Printed version W3338AE MS2830A/MS2840A Signal Analyzer Vector Signal Generator Operation Manual (Remote Control) Printed version W2914AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Vector Signal Generator Operation Manual (IQproducer™) Printed version W2929AE MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal Analyzer Vector Signal Generator Operation Manual (Standard Waveform Pattern) Printed version

Model Number Product Name Remarks K240B Power divider (K connector) DC to 26.5 GHz, 50 Ω K-J, 1Wmax MA1612A FOUR-PORT Junction PAD 5 MHz to 3 GHz, N-J MP752A TERMINATION DC to 12.4 GHz, 50 Ω N-P MA24106A USB Power Sensor 50 MHz to 6 GHz, with USB/Mini B cable (Refer to Chapter 7) J0576B Coaxial Cord Approx. 1 m length (N-P, 5D-2W, N-P) J0576D Coaxial Cord Approx. 2 m length (N-P, 5D-2W, N-P) J0127A Coaxial Cord Approx. 1 m length (BNC-P, RG58A/U, BNC-P) J0127B Coaxial Cord Approx. 2 m length (BNC-P, RG58A/U, BNC-P) J0127C Coaxial Cord Approx. 0.5 m length (BNC-P, RG58A/U, BNC-P) J0322A Coaxial Cord DC to 18 GHz, approx 0.5 m length (SMA-P, 50 Ω SUCOFLEX104, SMA-P) J0322B Coaxial Cord DC to 18 GHz, approx 1 m length (SMA-P, 50 Ω SUCOFLEX104, SMA-P) J0322C Coaxial Cord DC to 18 GHz, approx 1.5 m length (SMA-P, 50 Ω SUCOFLEX104, SMA-P) J0322D Coaxial Cord DC to 18 GHz, approx 2 m length (SMA-P, 50 Ω SUCOFLEX104, SMA-P) J1398A N-SMA ADAPTOR DC to 26.5 GHz, 50 Ω N-P, SMA-J J0911 Coaxial cord, 1.0 M (for 40 GHz) DC to 40 GHz, approx 1 m length (SF102A, 11K254/11K254/1.0M) J0912 Coaxial cord, 0.5 M (for 40 GHz) DC to 40 GHz, approx 0.5 m length (SF102A, 11K254/11K254/0.5M) 41KC-3 Fixed attenuator, 3 dB DC to 40 GHz, 3 dB

1-10 Table 1.2.3-1 Applicable Parts (Cont’d) Model Number Product Name Remarks J1261A Ethernet cable (shield type) Straight cable, 1 m J1261B Ethernet cable (shield type) Straight cable, 3 m J1261C Ethernet cable (shield type) Crossover cable, 1 m J1261D Ethernet cable (shield type) Crossover cable, 3 m J0008 GPIB cable, 2.0 m Approx. 2 m length J1487A AUX conversion adapter AUX → BNC For vector signal generator option J1556A AUX conversion adapter AUX → BNC For vector signal generator option and BER measurement function option B0635A Rack Mount Kit B0636A Carrying case Protective cover, casters Z0975A Keyboard (USB) 34AKNF50 Ruggedized K-To-Type N Female Adapter DC to 20 GHz, SWR: 1.25 1.2.4 Application Software For the latest information on the application software, either visit the MS2830A page on Anritsu website or contact an Anritsu Service and Sales office. Application software is sold separately. Anritsu website: http://www.anritsu.com/

Table 1.3.1-1 through Table 1.3.1-3 show the specifications. The following specification values are those under the conditions after 30-min warm-up at stable ambient temperature. Typical values are only for reference and are not guaranteed. Nominal values are not guaranteed. The following conditions should apply (unless otherwise noted): Auto Sweep Time Select : Normal Auto Swp Type Rules : Swept Only Switching Speed mode : Normal (Best Phase Noise) Attenuator Mode : Mechanical Atten Only The specifications of the Signal Analyzer function are values at the center frequency if not specified.

1-12 Table 1.3.1-1 Specifications for Mainframe Item Specification Frequency Frequency range 9 kHz to 3.6 GHz (MS2830A-040) 9 kHz to 6 GHz (MS2830A-041) 9 kHz to 13.5 GHz (MS2830A-043) 9 kHz to 26.5 GHz (MS2830A-044) 9 kHz to 43 GHz (MS2830A-045) Frequency band configuration Band Mixer harmonic order [N] 9 kHz to 4000 MHz 0 1 3500 MHz to 4400 MHz 1 1/2 4300 MHz to 6100 MHz 1 1 5900 MHz to 10575 MHz 2 1 10425 MHz to 13600 MHz 2 2 With MS2830A-044/045 installed, Band Mixer harmonic order [N] 9 kHz to 4000 MHz 0 1 3500 MHz to 4400 MHz 1 1/2 4300 MHz to 6000 MHz 1 1 3900 MHz to 8000 MHz 3 1 7900 MHz to 10575 MHz 4 1 10475 MHz to 12200 MHz 5 2 12100 MHz to 18400 MHz 6 2 18300 MHz to 26600 MHz 7 4 26500 MHz to 41900 MHz 8 4 41800 MHz to 43000 MHz 9 8 Preselector range Frequency Band Mode: Normal 4 GHz to 6 GHz (MS2830A-041) Frequency Band Mode: Spurious 3.5 GHz to 6 GHz (MS2830A-041) Frequency Band Mode: Normal 4 GHz to 13.5 GHz (MS2830A-043) Frequency Band Mode: Spurious 3.5 GHz to 13.5 GHz (MS2830A-043) Frequency Band Mode: Normal 4 GHz to 26.5 GHz (MS2830A-044) Frequency Band Mode: Spurious 3.5 GHz to 26.5 GHz (MS2830A-044) Frequency Band Mode: Normal 4 GHz to 43 GHz (MS2830A-045) Frequency Band Mode: Spurious 3.5 GHz to 43 GHz (MS2830A-045) Frequency settings Settable range Resolution –100 MHz to 3.7 GHz (MS2830A-040) –100 MHz to 6.1 GHz (MS2830A-041) –100 MHz to 13.6 GHz (MS2830A-043) –100 MHz to 26.6 GHz (MS2830A-044) –100 MHz to 43.1 GHz (MS2830A-045) 1 Hz

Item Specification Internal reference oscillator With MS2830A-040/041/043 installed, Without MS2830A-001/101/002/102 installed, Aging rate ±1 × 10–6/year Temperature characteristics ±2.5 × 10–6 (5 to 45°C) With MS2830A-002/102 installed, Activation characteristics Based on frequency 24 hours after power application, at 23°C ±5 × 10–7 (2 minutes after power application) ±5 × 10–8 (5 minutes after power application) Aging rate ±1 × 10–7/year Temperature characteristics ±2 × 10–8 (5 to 45°C) With MS2830A-044/045 installed, Activation characteristics Based on frequency 24 hours after power application, at 23°C ±5 × 10–7 (2 minutes after power application) ±5 × 10–8 (5 minutes after power application) Aging rate ±1 × 10–7/year Temperature characteristics ±2 × 10–8 (5 to 45°C) With MS2830A-040/041/043/044/045 installed, With MS2830A-001/101 installed, Activation characteristics Based on frequency 24 hours after power application, at 23°C ±1×10–9 (7 minutes after power application) Aging rate ±1×10–10/month Temperature characteristics ±1×10–9 (5 to 45°C)

1-14 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification Single side band noise At 18 to 28°C, 500 MHz, spectrum analyzer function Switching Speed mode: Normal (Best Phase Noise) (Frequency offset) 100 kHz 1 MHz –115 dBc/Hz –133 dBc/Hz With MS2830A-062 installed and operating (062: Enabled, Center frequency: 500 MHz, and SPAN ≤ 1 MHz as spectrum analyzer) at the temperature of 18 to 28°C. (Frequency Offset) 1 kHz 10 kHz 100 kHz 1 MHz –107 dBc/Hz –113 dBc/Hz –133 dBc/Hz –148 dBc/Hz Nominal With MS2830A-066 installed and operating (066: Enabled, Center frequency: 500 MHz, and SPAN ≤ 1 MHz as spectrum analyzer) at the temperature of 18 to 28°C. (Frequency Offset) 1 kHz 10 kHz 100 kHz 1 MHz –109 dBc/Hz –118 dBc/Hz –133 dBc/Hz –148 dBc/Hz Nominal With MS2830A-066 installed and operating (066: Enabled, Center frequency: 220 MHz, and SPAN ≤ 500 kHz as spectrum analyzer) at the temperature of 18 to 28°C. (Frequency Offset) 25 kHz –122 dBc/Hz

Item Specification Amplitude Measurement range Without MS2830A-008/108/068/168 or with Preamplifier turned off Average noise level up to +30 dBm With MS2830A-008/108/068/168 and Preamplifier turned on Average noise level up to +10 dBm Maximum input level Continuous wave average power DC Continuous wave average power DC Continuous wave average power DC Continuous wave average power DC With MS2830A-040/041/043 installed, Without MS2830A-008/108 or with Preamplifier turned off: +30 dBm (Input attenuator ≥ 10 dB) +20 dBm (Input attenuator = 0 dB) ±10 Vdc With MS2830A-008/108 and Preamplifier turned on: +10 dBm (Input attenuator = 0 dB) ±10 Vdc With MS2830A-044/045 installed, Without MS2830A-008/108/068/168 or with Preamplifier turned off: +30 dBm (Input attenuator ≥ 10 dB) +20 dBm (Input attenuator = 0 dB) ±0 Vdc With MS2830A-008/108/068/168 and Preamplifier turned on: +10 dBm (Input attenuator = 0 dB) ±0 Vdc Input attenuator With MS2830A-040/041/043/044 installed, 0 to 60 dB, 2 dB steps With MS2830A-045 installed, Attenuator Mode: E-ATT Combined Mode, Frequency Band Mode: Normal, and Stop frequency ≤ 6 GHz. or Attenuator Mode: E-ATT Combined Mode, Frequency Band Mode: Spurious, and Stop frequency ≤ 4 GHz. 0 to 10 dB, 10 dB steps 10 to 40 dB, 2 dB steps 40 to 60 dB, 10 dB steps Attenuator Mode: M-ATT Only. or Attenuator Mode: E-ATT Combined Mode, Frequency Band Mode: Normal, and Stop frequency > 6 GHz. or Attenuator Mode: E-ATT Combined Mode, Frequency Band Mode: Spurious, and Stop frequency > 4 GHz. 0 to 60 dB, 10 dB steps

1-16 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification Input attenuator switching error Based on input attenuator 10 dB, at 18 to 28°C Without MS2830A-008/108/068/168 or with Preamplifier turned off: ±0.2 dB (10 to 60 dB) (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±0.75 dB (10 to 60 dB) (4 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±0.80 dB (10 to 60 dB) (13.8 GHz ≤ frequency ≤ 26.5 GHz) ±1.0 dB (10 to 60 dB) (26.5 GHz ≤ frequency ≤ 40 GHz) ±1.0 dB typ.(10 to 60 dB) (40 GHz ≤ frequency ≤ 43 GHz) Reference level Setting range Log scale: –120 to +50 dBm or equivalent value Linear scale: 22.4 µV to 70.7 V or equivalent value Resolution: 0.01 dB or equivalent level Unit Log scale: dBm, dBµV, dBmV, dBµV (emf), dBµV/m, V, W Linear scale: V

Item Specification Linearity error Without MS2830A-008/108/068/168 or with Preamplifier turned off: Excluding the noise floor effect ±0.07 dB (mixer input level ≤ –20 dBm) ±0.10 dB (mixer input level ≤ –10 dBm) With MS2830A-008/108 and with Preamplifier turned on: Excluding the noise floor effect ±0.07 dB (Preamplifier Input Level:≤–40 dBm) ±0.10 dB (Preamplifier Input Level:≤–30 dBm) When Attenuator Mode is E-ATT Combined: Without MS2830A-008/108/068/168 and with Preamplifier turned off: Excluding the noise floor effect ±0.07 dB (mixer input level:≤ –20 dBm, RF Input Level:≤–10 dBm) ±0.10 dB (mixer input level:≤ –10 dBm, RF Input Level:≤–10 dBm) ±0.07 dB Nominal (mixer input level:≤ –20 dBm, 9 kHz ≤ frequency ≤ 300 MHz, RF input level ≤+5 dBm) (mixer input level:≤ –20 dBm, 300 MHz < frequency ≤ 6 GHz, RF input level ≤ +20 dBm) ±0.10 dB Nominal (mixer input level:≤ –10 dBm, 9 kHz ≤ frequency ≤ 300 MHz, RF input level ≤+5 dBm) (mixer input level:≤ –10 dBm, 300 MHz < frequency ≤ 6 GHz, RF input level ≤ +20 dBm)

1-18 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification RF frequency characteristics After CAL execution at 18 to 28°C, input attenuator = 10 dB, With MS2830A-040/041/043, and without MS2830A-008/108, or with Preamplifier turned off: ±1.0 dB (9 kHz ≤ frequency < 300 kHz) ±0.35 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.50 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) ±1.50 dB (6 GHz < frequency) With MS2830A-040/041/043, and with MS2830A-008/108, and with Preamplifier turned on: ±0.65 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) With MS2830A-044/045, Without MS2830A-008/108/068/168, or with Preamplifier turned off, Without MS2830A-067/167 or with Microwave Preselector Bypass turned off and after Preselector Auto Tune is done: ±1.0 dB (9 kHz ≤ frequency < 300 kHz) ±0.35 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.50 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) ±1.50 dB (6 GHz < frequency ≤ 13.8 GHz) ±2.50 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±2.50 dB (26.5 GHz < frequency ≤ 40 GHz) ±2.50 dB typ. (40 GHz < frequency ≤ 43 GHz)

Item Specification RF frequency characteristics (Cont’d) With MS2830A-044/045, and with MS2830A-008/108, and with Preamplifier turned on: ±0.65 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) With MS2830A-044/045, and with MS2830A-068/168, with Preamplifier turned on, Without MS2830A-067/167 or with Microwave Preselector Bypass turned off and after Preselector Auto Tune is done: ±0.65 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±2.50 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±3.50 dB (26.5 GHz < frequency ≤ 40 GHz) ±3.50 dB Nominal (40 GHz < frequency ≤ 43 GHz)

1-20 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification 1 dB gain compression With MS2830A-040/041/043 installed, Without MS2830A-008/108 or with Preamplifier turned off: At mixer input level ≥+3 dBm (300 MHz ≤ frequency ≤ 6 GHz) ≥–1 dBm (6 GHz < frequency ≤ 13.5 GHz) With MS2830A-008/108 and Preamplifier turned on: At Preamplifier input level ≥–15 dBm (300 MHz ≤ frequency ≤ 6 GHz) With MS2830A-044/045 installed, Without MS2830A-008/108/068/168 or with Preamplifier turned off: At mixer input level ≥+3 dBm (300 MHz ≤ frequency ≤ 4 GHz) ≥–1 dBm (4 GHz < frequency ≤ 13.5 GHz) ≥–1 dBm (13.5 GHz < frequency ≤ 26.5 GHz) ≥–1 dBm Nominal (26.5 GHz < frequency ≤ 40 GHz) With MS2830A-068/168 and Preamplifier turned on: At Preamplifier input level ≥–15 dBm (300 MHz ≤ frequency ≤ 4 GHz) ≥–21 dBm (4 GHz < frequency ≤ 13.5 GHz) ≥–21 dBm (13.5 GHz < frequency ≤ 26.5 GHz) ≥–21 dBm Nominal (26.5 GHz < frequency ≤ 40 GHz)

Item Specification Spurious response Secondary harmonic wave distortion With MS2830A-040/041/043 installed, Without MS2830A-008/108 or with Preamplifier turned off: At mixer input level = –30 dBm Harmonics [dBc] SHI [dBm] ≤–60 ≥+30 (10 MHz ≤ Input frequency ≤ 300 MHz) ≤–65 ≥+35 (300 MHz < Input frequency ≤ 1 GHz) ≤–65 ≥+35 (1 GHz < Input frequency ≤ 2 GHz) At mixer input level = –10 dBm Harmonics [dBc] SHI[dBm] ≤–70 ≥+60 (2 GHz < Input frequency ≤ 3 GHz, Frequency Band Mode: Normal) ≤–70 ≥+60 (1.75 GHz ≤ Input frequency≤ 3 GHz, Frequency Band Mode: Spurious) At mixer input level = –10 dBm Harmonics [dBc] SHI[dBm] ≤–70 ≥+60 (3 GHz < Input frequency ≤ 6.75 GHz) With MS2830A-008/108 and with Preamplifier turned on: At preamplifier input level = –45 dBm Harmonics [dBc] SHI[dBm] ≤–50 ≥+5 (10 MHz ≤ frequency ≤ 300 MHz) ≤–55 ≥+10 (300 MHz ≤ frequency ≤ 3 GHz) With MS2830A-044/045 installed, Without MS2830A-008/108/068/168 and MS2830A-067/167: At mixer input level = –30 dBm Harmonics [dBc] SHI[dBm] ≤–60 ≥+30 (10 MHz ≤ Input frequency ≤ 300 MHz) ≤–65 ≥+35 (300 MHz < Input frequency ≤ 1 GHz) ≤–65 ≥+35 (1 GHz < Input frequency ≤ 2 GHz, Frequency Band Mode: Normal) ≤–65 ≥+35 (1 GHz < Input frequency ≤ 1.75 GHz, Frequency Band Mode: Spurious)

1-22 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification Secondary harmonic wave distortion (Cont’d) At mixer input level = –10 dBm Harmonics [dBc] SHI [dBm] ≤–70 ≥+60 (2 GHz < Input frequency ≤ 3 GHz, Frequency Band Mode: Normal) ≤–70 ≥+60 (1.75 GHz ≤ Input frequency ≤ 3 GHz, Frequency Band Mode: Spurious) ≤–90 ≥+80 (3 GHz < Input frequency ≤ 6.75 GHz) ≤–90 ≥+80 (6.75 GHz < Input frequency ≤ 13.25 GHz) ≤–90 ≥+80 Nominal (13.25 GHz < Input frequency ≤ 21.5 GHz) With MS2830A-044/045 installed, With MS2830A-068/168 and with Preamplifier turned off: Or with MS2830A-067/167 and with Microwave Preselector Bypass turned off: At mixer input level = –30 dBm Harmonics [dBc] SHI [dBm] ≤–60 ≥+30 (10 MHz ≤ frequency ≤ 300 MHz) ≤–65 ≥+35 (300 MHz < frequency ≤ 1 GHz) ≤–65 ≥+35 (1 GHz < frequency ≤ 2 GHz, Frequency Band Mode: Normal) ≤–65 ≥+35 (1 GHz < frequency ≤ 1.75 GHz, Frequency Band Mode: Spurious) At mixer input level = –10 dBm Harmonics [dBc] SHI [dBm] ≤–70 ≥+60 (2 GHz < Input frequency ≤ 3 GHz, Frequency Band Mode: Normal) ≤–70 ≥+60 (1.75 GHz ≤ Input frequency ≤ 3 GHz, Frequency Band Mode: Spurious) ≤–70 ≥+60 (3 GHz < Input frequency ≤ 6.75 GHz) ≤–70 ≥+60 (6.75 GHz < Input frequency ≤ 13.25 GHz) ≤–70 ≥+60 Nominal (13.25 GHz < Input frequency ≤ 21.5 GHz)

Item Specification Secondary harmonic wave distortion (Cont’d) With MS2830A-044/045 installed, With MS2830A-008/108/068/168 and with Preamplifier turned on: Or with MS2830A-067/167 and with Microwave Preselector Bypass turned off: At mixer input level = –45 dBm Harmonics [dBc] SHI [dBm] ≤–50 ≥+5 (10 MHz ≤ Input frequency ≤ 300 MHz) ≤–55 ≥+10 (300 MHz < Input frequency ≤ 2 GHz) ≤–45 ≥0 (2 GHz < Input frequency ≤ 6.75 GHz) ≤–45 ≥0 (6.75 GHz < Input frequency ≤ 13.25 GHz) ≤–40 ≥–5 Nominal (13.25 GHz < Input frequency ≤ 21.5 GHz) When Attenuator Mode is E-ATT Combined: Without MS2830A-008/108/068/168 and with Preamplifier turned off: At mixer input level = –30 dBm Harmonics [dBc] SHI [dBm] ≤–60 ≥+30 (10 MHz ≤ Input frequency ≤ 300 MHz, RF input level ≤ –5 dBm) ≤–65 ≥+35 (300 MHz < Input frequency ≤ 1 GHz, RF input level ≤ –5 dBm) ≤–65 ≥+35 (1 GHz < Input frequency ≤ 2 GHz, Frequency Band Mode: Normal, RF input level ≤ +5 dBm) (1 GHz

1-24 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification Secondary harmonic wave distortion (Cont’d) At mixer input level = –30 dBm Harmonics [dBc] SHI [dBm] ≤–60 ≥+30 Nominal (10 MHz ≤ Input frequency ≤ 300 MHz, RF input level ≤ 0 dBm) ≤–65 ≥+35 Nominal (300 MHz < Input frequency ≤ 1 GHz, RF input level ≤ +15 dBm) ≤–65 ≥+35 Nominal (1 GHz < Input frequency ≤ 2 GHz, Frequency Band Mode: Normal, RF input level ≤ +15 dBm) (1 GHz < Input frequency ≤ 1.75 GHz, Frequency Band Mode: Spurious, RF input level ≤ +15 dBm) At mixer input level = –10 dBm Harmonics [dBc] SHI [dBm] ≤–70 ≥+60 Nominal (2 GHz ≤ Input frequency ≤ 3 GHz, Frequency Band Mode: Normal, RF input level ≤ +15 dBm) (1.75 GHz ≤ Input frequency ≤ 3 GHz, Frequency Band Mode: Spurious, RF input level ≤ +15 dBm) SHI: Second Harmonic Intercept Residual response Frequency ≥1 MHz, Input attenuator = 0 dB, at 50 Ω terminator (With MS2830A-077/177/078/178 installed, excluding Bandwidth > 31.25 MHz.) Up to 1 GHz ≤ –100 dBm 1 GHz to 6 GHz ≤ –90 dBm typ. 6 GHz to 13.5 GHz ≤ –90 dBm Nominal 13.5 GHz to 26.5 GHz ≤ –90 dBm Nominal. 26.5 GHz to 40 GHz ≤ –80 dBm Nominal. Connector RF input Connector With MS2830A-040/041/043/044, Front panel, N-J, 50 Ω VSWR: Input attenuator ≥10 dB, 18 to 28ºC ≤ 1.2 (Nominal) (40 MHz ≤ frequency ≤ 3 GHz) ≤ 1.5 (Nominal) (3 GHz < frequency ≤ 6 GHz) ≤ 1.6 (Nominal) (6 GHz < frequency ≤ 13.5 GHz) ≤ 1.9 (Nominal) (13.5 GHz < frequency ≤ 26.5 GHz) With MS2830A-045, Front panel, N-J, 50 Ω VSWR: Input attenuator ≥10 dB, 18 to 28ºC ≤ 1.2 (Nominal) (40 MHz ≤ frequency ≤ 3 GHz) ≤ 1.3 (Nominal) (3 GHz < frequency ≤ 6 GHz) ≤ 1.3 (Nominal) (6 GHz < frequency ≤ 13.5 GHz) ≤ 1.4 (Nominal) (13.5 GHz < frequency ≤ 26.5 GHz) ≤ 1.6 (Nominal) (26.5 GHz < frequency ≤ 40 GHz) ≤ 1.6 (Nominal) (40 GHz < frequency ≤ 43 GHz) 40 GHz < frequency ≤ 43 GHz is a value with the V-K converter mounted and included

Item Specification RF output Connector This is available when the Option 020/120/021/121 is installed. Front panel, N-J, 50 Ω (Nominal value) Refer to MS2830A Signal Analyzer Vector Signal Generator Operation Manual Operation. 1st Local Output Output Input Connector This is available when the Option 044/045 is installed. Connector for External Mixer Local signal, bias current Local signal: Frequency 5 to 10 GHz, output level ≥10 dBm typ. IF signal: Frequency 1875 MHz Front panel, SMA-J, 50 Ω (Nominal) External reference input Connector Frequency Operating range Input Level Rear panel, BNC-J, 50 Ω (Nominal) 5 MHz/10 MHz/13 MHz ±1 ppm –15 dBm ≤ level ≤ +20 dBm, 50 Ω (AC coupling) Reference signal output Connector Frequency Output Level Rear panel, BNC-J, 50 Ω (Nominal value) 10 MHz ≥ 0 dBm (AC coupling) Sweep Status Output Connector Output Level Rear panel, BNC-J TTL level (high level at sweep or waveform acquisition) SA Trigger Input Connector Input Level Rear panel, BNC-J TTL level SG Trigger Input Connector Input Level Available with option 020/120/021/121 installed. Rear panel, BNC-J TTL level External controls Control from external controller (except power) Ethernet (10/100/1000Base-T) Connector Connector Rear panel, RJ-45 GPIB Connector Interface function IEEE488.2 compatible Rear panel, IEEE488 bus connector SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT0, C0, E2 USB (B) Connector USB2.0 compatible Rear panel, USB-B connector

1-26 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification USB Connector Used to connect the USB power sensor or to connect a USB memory stick for saving and reading the files (parameters, waveforms, screen copies, etc.). USB 2.0 compatible USB-A connector (2 ports on front panel, 2 ports on rear panel) Monitor Output Connector Rear panel, VGA compatibility, mini D-SUB 15 pin Aux Connector Used for the input/output of an auxiliary device. Rear panel, 50 pins (DX10A-50S equivalent part) IF Output Connector Output frequency Gain This is available when the Option 044/045 is installed. Outputs the signal for the 1st IF output connector before band filtering. Rear panel, SMA-J, 50 Ω (Nominal) 1875 MHz –10 dB (Nominal, ATT = 0 dB, at 10 GHz input frequency) Connector for Noise Source Connector Output voltage range This is available when MS2830A-017/117 is installed. Rear panel, BNC-J +28 V±0.5 V, Pulsed Screen XGA color LCD (Resolution: 1024 × 768) Size: 8.4” (213 mm diagonal) External Mixer Frequency Frequency band configuration Amplitude Input/Output Display gain This is available when MS2830A-044/045 is installed. Frequency range: 26.5 to 325 GHz Band Frequency range Mixing order Band VHP 50.0 to 75.0 GHz 8+ Band EHP 60.0 to 90.0 GHz 12– Band A 26.5 to 40.0 GHz 4+ Band Q 33.0 to 50.0 GHz 5+ Band U 40.0 to 60.0 GHz 6+ Band V 50.0 to 75.0 GHz 8+ Band E 60.0 to 90.0 GHz 9+ Band W 75.0 to 110.0 GHz 11+ Band F 90.0 to 140.0 GHz 14+ Band D 110.0 to 170.0 GHz 17+ Band G 140.0 to 220.0 GHz 22+ Band Y 170.0 to 260.0 GHz 26+ Band J 220.0 to 325.0 GHz 33+ Setting range of mixer conversion loss 0 to 99.9 dB Maximum input level Depends on External Mixer Average noise level Depends on External Mixer Frequency response Depends on External Mixer Applicable mixer: Two-port mixer only Local frequency 5 to 10 GHz IF frequency 1875 MHz 0±2 dB at External mixer input level: –10 dBm. mixer conversion loss: 15 dB

Item Specification Overall Specifications Mass, Weight Dimensions Weight 177 mm (h) × 426 mm (w) × 390 mm (d) (excluding protrusions) ≤ 14.5 kg (with MS2830A-040 or -041 and MS2830A-020 or -021 options installed; excludes all other options) ≤ 13.5 kg (with MS2830A-043 options installed; excludes all other options) ≤ 15 kg (with MS2830A-044 or -045 installed; excludes all other options) Power Supply Voltage Frequency Power consumption Rated Voltage: AC 100 to 120 V or 200 to 240 V 50 to 60 Hz ≤350 VA (including all options, maximum value) 110 VA Nominal (With MS2830-040 or 041 installed, excluding other options) 130 VA Nominal (With MS2830-043 installed, excluding other options) 170 VA Nominal (With MS2830-040/041, -020/021 and -022 installed, excluding other options) 190 VA Nominal (With MS2830-043, -020/021, and -022 installed, excluding other options) Temperature Operating temperature Storage temperature 5 to 45°C –20 to +60°C Environment Performance Conducted emission Conforms to EN 61326-1 Radiated emission Conforms to EN 61326-1 Harmonic current emission Conforms to EN 61000-3-2 Electrostatic discharge Conforms to EN 61326-1 Electromagnetic field immunity Conforms to EN 61326-1

1-28 Table 1.3.1-1 Specifications for Mainframe (Cont’d) Item Specification Fast transient/burst Conforms to EN 61326-1 Surge Conforms to EN 61326-1 Conducted RF Conforms to EN 61326-1 Power frequency magnetic field Conforms to EN 61326-1 Voltage dips/short interruption Conforms to EN 61326-1 Table 1.3.1-2 Specifications for Signal Analyzer Function Item Specification Common Trace mode Spectrum, Power vs Time, Frequency vs Time, CCDF, Spectrogram, No Trace Bandwidth Specifies the capture analysis bandwidth from the center frequency 1 kHz to 10 MHz (1-2.5-5 sequence) (With MS2830A-006/106) 1 kHz to 25 MHz (1-2.5-5 sequence), 31.25 MHz (With MS2830A-005/105, MS2830A-007 or MS2830A-009/109 installed.) 1 kHz to 25 MHz (1-2.5-5 sequence), 31.25 MHz, 50 MHz, 62.5 MHz (With MS2830A-077/177 installed.) 1 kHz to 25 MHz (1-2.5-5 sequence), 31.25 MHz, 50 MHz, 62.5 MHz, 100 MHz, 125 MHz (With MS2830A-078/178 installed.) Sampling rate Automatically set depending on analysis bandwidth 2 kHz to 20 MHz (1-2-5 sequence) (With MS2830A-006/106) 2 kHz to 50 MHz (1-2-5 sequence) (With MS2830A-005/105, MS2830A-007 or MS2830A-009/109 installed.) 2 kHz to 100 MHz (1-2-5 sequence) (With MS2830A-077/177 installed.) 2 kHz to 200 MHz (1-2-5 sequence) (With MS2830A-078/178 installed.)

Item Specification Capture time Capture Time Length Minimum capture time: Maximum capture time: Setting mode Capture Time Length Minimum capture time: Maximum capture time: Setting mode Capture Time Length Minimum capture time: Maximum capture time: Setting mode Sets the capture time length 2 µs to 50 ms (determined depending on analysis bandwidth) 2 to 2000 s (determined depending on analysis bandwidth) Auto, Manual (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) Sets the capture time length. 1 µs (determined depending on analysis bandwidth) 500 ms (determined depending on analysis bandwidth) Auto, Manual (With MS2830A-077/177 installed and Bandwidth > 31.25 MHz.) Sets the capture time length. 500 ns to 1 µs (determined depending on analysis bandwidth) 500 ms (determined depending on analysis bandwidth) Auto, Manual (With MS2830A-078/178 installed and Bandwidth > 31.25 MHz.) Trigger Trigger mode Free Run (Trig Off), Video, Wide IF Video, Frame, External (TTL) SG Marker (With Option 020/120/021/121) ADC resolution 16 bits (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) Spectrum indicator function Function overview Displays the spectrum for arbitrary time length and frequency range in the acquired waveform data. Analysis time range Analysis Start Time Analysis Time Length Setting mode Sets analysis start time position from beginning of waveform data. Sets analysis time span. Auto, Manual

1-30 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Frequency Center frequency and SPAN can be set within the frequency range in waveform data. Frequency settings 0 MHz to 3.6 GHz (MS2830A-040) 0 MHz to 6 GHz (MS2830A-041) 0 MHz to 13.5 GHz (MS2830A-043) 0 MHz to 26.5 GHz (MS2830A-044) 0 MHz to 43 GHz (MS2830A-045) (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) 300 MHz to 3.6 GHz (MS2830A-040) 300 MHz to 6 GHz (MS2830A-041) 300 MHz to 13.5 GHz (MS2830A-043) (With MS2830A-077/177/078/178 installed and Bandwidth > 31.25 MHz.) 300 MHz to 6 GHz (MS2830A-044) 300 MHz to 6 GHz (MS2830A-045) (With MS2830A-077/177/078/178 installed but MS2830A-067/167 not installed and Bandwidth > 31.25 MHz.) 300 MHz to 26.5 GHz (MS2830A-044) 300 MHz to 43 GHz (MS2830A-045) (With MS2830A-077/177/078/178 and MS2830A-067/167 installed and Bandwidth > 31.25 MHz.) Display frequency accuracy ±[Indicator frequency × reference frequency accuracy + SPAN frequency × reference frequency accuracy + RBW × 0.05 + 2 × N + SPAN frequency / (Trace point count – 1)] Hz N：Mixer harmonic order Resolution bandwidth (RBW) Setting range Selectivity Setting range Selectivity Setting range Selectivity 1 Hz to 1 MHz (1-3 sequence) (–60 dB/–3 dB) 4.5:1, nominal value (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) 1 Hz to 3 MHz (1-3 sequence) (–60 dB/–3 dB) 4.5:1, Nominal value (With MS2830A-077/177 installed and Bandwidth > 31.25 MHz.) 1 Hz to 10 MHz (1-3 sequence) (–60 dB/–3 dB ) 4.5:1, Nominal value (With MS2830A-078/178 installed and Bandwidth > 31.25 MHz.)

Item Specification Absolute amplitude accuracy After CAL execution at 18 to 28ºC, RBW = Auto, Time Detection = Average, Marker Result = Integration or Peak (Accuracy), center frequency, CW, excluding the noise floor effect With Preamplifier turned off: Input attenuator ≥ 10 dB, Mixer input level ≤ –10 dBm With Preamplifier turned on: Input attenuator = 10 dB, preamplifier input level ≤ –30 dBm, With MS2830A-041/042/043 installed, Without MS2830A-008/108 or with Preamplifier turned off: ±0.5 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Normal) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) ±1.8 dB (6 GHz < frequency ≤ 13.5 GHz) With MS2830A-008/108 and with Preamplifier turned on: ±1.0 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious)

1-32 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Absolute amplitude accuracy (Cont’d) With MS2830A-044/045 installed, Without MS2830A-068/168 or with Preamplifier turned off: ±0.5 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Spurious) ±1.8 dB (6 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (4 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±3.0 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±3.0 dB (26.5 GHz < frequency ≤ 40 GHz) ±3.5 dB Nominal (40 GHz < frequency ≤ 43 GHz) With MS2830A-044/045 installed, With MS2830A-068/168 and Preamplifier turned on: ±1.0 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Spurious) ±2.0 dB (6 GHz < frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (4 GHz < frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±3.0 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±4.0 dB (26.5 GHz < frequency ≤ 40 GHz) ±4.0 dB Nominal (40 GHz < frequency ≤ 43 GHz) The absolute amplitude accuracy is calculated from an RSS (root summed square) error of the RF frequency characteristics, linear error and input attenuator switching error.

Item Specification In-band frequency characteristics With MS2830A-040/041/043 installed, (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) On the basis of a level of the center frequency, at 18 to 28°C in center frequency ±10 MHz ±0.31 dB (30 MHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Normal) (30 MHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) With MS2830A-044/045 installed, (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) On the basis of a level of the center frequency, at 18 to 28°C in center frequency ±10 MHz ±0.31 dB (30 MHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Normal) (30 MHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious)

1-34 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Display average noise level With MS2830A-040/041/043 installed, (With MS2830A-077/177/078/178 not installed or Bandwidth ≤ 31.25 MHz.) Without MS2830A-062/066, Without MS2830A-008/108 or with Preamplifier turned off: At 18 to 28ºC, input attenuator = 0 dB, 100 kHz –131.5 [dBm/Hz] 1 MHz –141.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –150.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –148.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –146.5 [dBm/Hz] With MS2830A-041/043 3.5 GHz < frequency ≤ 6 GHz –143.5 [dBm/Hz] With MS2830A-043 6 GHz < frequency ≤ 13.5 GHz –139.5 [dBm/Hz] Without MS2830A-062/066, With MS2830A-008/108 or with Preamplifier turned on: At 18 to 28ºC, input attenuator = 0 dB, 100 kHz –144.5 [dBm/Hz] Nominal 1 MHz –153.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –160.5 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –159.5 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –157.5 [dBm/Hz] With MS2830A-041/043, Frequency Band Mode: Normal 3.5 GHz < frequency ≤ 4 GHz –154.5 [dBm/Hz] With MS2830A-041/043, Frequency Band Mode: Spurious 3.5 GHz < frequency ≤ 4 GHz –154.5 [dBm/Hz] With MS2830A-041/043 4 GHz < frequency ≤ 6 GHz –154.5 [dBm/Hz] With MS2830A-062/066 installed, Without MS2830A-008/108 or with Preamplifier turned off: At 18 to 28ºC, input attenuator = 0 dB, 100 kHz –130.5 [dBm/Hz] 1 MHz –140.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –149.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –147.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –144.5 [dBm/Hz] With MS2830A-041/043 installed, 3.5 GHz < frequency ≤ 6 GHz –141.5 [dBm/Hz] With MS2830A-043 installed, 6 GHz < frequency ≤ 13.5 GHz –139.5 [dBm/Hz]

Item Specification Display average noise level (Cont’d) With MS2830A-062/066 installed, With MS2830A-008/108 and with Preamplifier turned on: At 18 to 28ºC, input attenuator = 0 dB, 100 kHz –143.5 [dBm/Hz] Nominal 1 MHz –152.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –159.5 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –158.5 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –155.5 [dBm/Hz] With MS2830A-041/043 installed, Frequency Band Mode: Normal 3.5 GHz < frequency ≤ 4 GHz –151.5 [dBm/Hz] With MS2830A-041/043 installed, Frequency Band Mode: Spurious 3.5 GHz < frequency ≤ 4 GHz –151.5 [dBm/Hz] With MS2830A-041/043 installed, 4 GHz < frequency ≤ 6 GHz –151.5 [dBm/Hz] With MS2830A-040/041/043 installed, With MS2830A-077/177/078/178, analysis bandwidth > 31.25 MHz Without MS2830A-062/066, Without MS2830A-008/108, or with Preamplifier turned off At 18 to 28ºC, input attenuator = 0 dB, 300 MHz ≤ frequency < 1 GHz –146.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –144.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –142.5 [dBm/Hz] With MS2830A-041/043 installed, 3.5 GHz < frequency ≤ 6 GHz –139.5 [dBm/Hz] With MS2830A-043 installed, 6 GHz < frequency ≤ 13.5 GHz –135.5 [dBm/Hz] Without MS2830A-062/066, With MS2830A-008/108, and with Preamplifier turned on At 18 to 28ºC, input attenuator = 0 dB, 300 MHz ≤ frequency < 1 GHz –156.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –155.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –153.5 [dBm/Hz] With MS2830A-043 installed, 3.5 GHz < frequency ≤ 6 GHz –150.5 [dBm/Hz] With MS2830A-062/066, Without MS2830A-008/108, or with Preamplifier turned off At 18 to 28ºC, input attenuator = 0 dB, 300 MHz ≤ frequency < 1 GHz –143.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –141.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –138.5 [dBm/Hz] With MS2830A-041/043 installed, 3.5 GHz < frequency ≤ 6 GHz –135.5 [dBm/Hz] With MS2830A-043 installed, 6 GHz < frequency ≤ 13.5 GHz –135.5 [dBm/Hz]

1-36 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Display average noise level (Cont’d) With MS2830A-062/066, With MS2830A-008/108, and with Preamplifier turned on At 18 to 28ºC, input attenuator = 0 dB, 300 MHz ≤ frequency < 1 GHz –153.5 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –152.5 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –149.5 [dBm/Hz] With MS2830A-041/043 installed, 3.5 GHz ≤ frequency < 6 GHz –145.5 [dBm/Hz] With MS2830A-044/045 installed, Without MS2830A-077/177/078/178, or analysis bandwidth ≤ 31.25 MHz Without MS2830A-067/167/068/168 or with Preamplifier turned off, Frequency Band Mode: Normal 100 kHz –131.5 [dBm/Hz] 1 MHz –141.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –150.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –147.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –144.5 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –141.5 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –141.5 [dBm/Hz] 6 GHz < frequency ≤ 13.5 GHz –148.5 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –146.5 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –143.5 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –143.5 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –141.5 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –137.5 [dBm/Hz] Without MS2830A-067/167 and with MS2830A-068/168, and with Preamplifier turned off, Frequency Band Mode: Normal 100 kHz –131.5 [dBm/Hz] 1 MHz –141.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –150.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –147.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –144.5 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –141.5 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –141.5 [dBm/Hz] 6 GHz < frequency ≤ 13.5 GHz –144.5 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –142.5 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –138.5 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –138.5 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –132.5 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –129.5 [dBm/Hz]

Item Specification Display average noise level (Cont’d) Without MS2830A-067/167 and with MS2830A-068/168, and with Preamplifier turned on, Frequency Band Mode: Normal 100 kHz –144.5 [dBm/Hz] Nominal 1 MHz –153.5 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –160.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –158.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –156.5 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –152.5 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –152.5 [dBm/Hz] 6 GHz < frequency ≤ 13.5 GHz –157.5 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –155.5 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –153.5 [dBm/Hz] With MS2830A-045 installed, 26.5 GHz < frequency ≤ 34 GHz –153.5 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –147.5 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –144.5 [dBm/Hz] With MS2830A-044/045 installed, With MS2830A-077/177/078/178, analysis bandwidth > 31.25 MHz Without MS2830A-008/108/068/168, or with Preamplifier turned off: At 18 to 28ºC, input attenuator = 0 dB, 300 MHz ≤ frequency < 1 GHz –146.5 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –143.5 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –140.5 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –137.5 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –137.5 [dBm/Hz] With MS2830A-008/108/068/168, and with Preamplifier turned on. At 18 to 28ºC, input attenuator = 0 dB, 300 MHz ≤ frequency < 1 GHz –156.5 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –154.5 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –152.5 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –148.5 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –148.5 [dBm/Hz] With MS2830A-077/177/078/178, with MS2830A-067/167, analysis bandwidth > 31.25 MHz, Without MS2830A-068/168, At 18 to 28ºC, input attenuator = 0 dB, 6 GHz ≤ frequency ≤ 13.5 GHz –137.5 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –135.5 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –131.5 [dBm/Hz] With MS2830A-045 Installed 26.5 GHz < frequency ≤ 34 GHz –131.5 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –125.5 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –122.5 [dBm/Hz]

1-38 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Display average noise level (Cont’d) With MS2830A-068/168, and with Preamplifier turned off. At 18 to 28ºC, input attenuator = 0 dB, 6 GHz ≤ frequency ≤ 13.5 GHz –132.5 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –130.5 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –126.5 [dBm/Hz] With MS2830A-045 Installed 26.5 GHz < frequency ≤ 34 GHz –126.5 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –121.5 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –118.5 [dBm/Hz] With MS2830A-068/168, and with Preamplifier turned on. At 18 to 28ºC, input attenuator = 0 dB, 6 GHz ≤ frequency ≤ 13.5 GHz –147.5 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –145.5 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –143.5 [dBm/Hz] With MS2830A-045 Installed 26.5 GHz < frequency ≤ 34 GHz –143.5 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –137.5 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –134.5 [dBm/Hz]

Item Specification Measurement function Adjacent Channel Power Measurement (ACP) Reference Adjacent channel specification Span Total, Carrier Total, Both Sides of Carriers or Carrier Select 3 channels × 2 Channel Power Absolute value measurement dBm, dBm/Hz Occupied Bandwidth (OBW) N% of Power method, X dB Down method Power vs Time Display Function Function overview Indicates time changes of power for captured waveform data. Analysis time range Analysis Start Time Analysis Time Length Setting mode Sets analysis start time position from beginning of waveform data. Sets analysis time span. Auto, Manual Resolution bandwidth Filter type Roll-off rate setting Filter frequency offset Rect, Gaussian, Nyquist, Root Nyquist, Off (default: Off) 0.01 to 1 (settable for Nyquist and Root Nyquist) Filter center frequency can be set within frequency band of waveform data. Peak to Peak measurement Measured using AM Depth or marker function. +Peak, –Peak, (P-P)/2, Average Burst Average Power Measures average power of burst signal.

1-40 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Frequency vs Time Display Function Function overview Displays frequency time fluctuations of input signal from captured waveform data. Analysis time range Analysis Start Time Analysis Time Length Setting mode Sets analysis start time position from beginning of waveform data. Sets analysis time span. Auto, Manual Operating level range –17 to +30 dBm (Input attenuator ≥ 10 dB) Frequency (vertical axis) Display frequency range Input frequency range Center frequency and SPAN can be set within the frequency range in waveform data Selectable from 1/25, 1/10, 1/5 and 1/2 of analysis bandwidth 10 MHz to 6 GHz Display frequency accuracy Input level = –17 to +30 dBm, SPAN ≤ 31.25 MHz, scale = SPAN/25: At CW input ±(reference oscillator accuracy × center frequency + indicator frequency range×0.01) Hz Peak to Peak measurement Measured using FM Depth or marker function. +Peak, –Peak, (P-P)/2, Average CCDF Display Function Function overview Displays CCDF and APD of waveform data captured at specific time. Analysis time range Analysis Start Time Analysis Time Length Setting mode Sets analysis start time position from beginning of waveform data. Sets analysis time span. Auto, Manual Display Histogram resolution Numerical value Graphically displays CCDF and APD. 0.01 dB Average Power, Max Power, Crest Factor Resolution Bandwidth Filter type Filter frequency offset Rectangle, Off (default: Off) Filter center frequency can be set within frequency band of waveform data.

Item Specification Spectrogram Display Function Function overview Displays the spectrum for selected time length in the acquired waveform data. Analysis time range Analysis Start Time Analysis Time Length Setting mode Sets analysis start time position from beginning of waveform data. Sets analysis time span. Auto, Manual Frequency Center frequency and SPAN can be set within the frequency range in waveform data. Resolution bandwidth (RBW) Setting range Selectivity 1 Hz to 1 MHz (1-3 sequence) (–60 dB/–3 dB ) 4.5:1, Nominal value Digitize function Function overview Capable of outputting captured waveform data to internal hard disk or external device Waveform data Format Level Level accuracy I, Q (32-bit Float Binary format) √(I2 + Q2) = 1 at 0 dBm input Same as absolute amplitude accuracy of signal analyzer External output Capable of outputting to external PC through Ethernet

1-42 Table 1.3.1-2 Specifications for Signal Analyzer Function (Cont’d) Item Specification Replay Function Function overview Analyzes traces of saved waveform data Conditions for measurable waveform data I, Q (Binary format) Conditions for measurable waveform data SPAN Sampling rate 1 kHz 2 kHz 2.5 kHz 5 kHz 5 kHz 10 kHz 10 kHz 25 kHz 25 kHz 50 kHz 50 kHz 100 kHz 100 kHz 200 kHz 250 kHz 500 kHz 500 kHz 1 MHz 1 MHz 2 MHz 2.5 MHz 5 MHz 5 MHz 10 MHz 10 MHz 20 MHz 18.6 MHz 20 MHz 20 MHz 25 MHz 25 MHz 50 MHz 31.25 MHz 50 MHz 50 MHz 100 MHz 62.5 MHz 100 MHz 100 MHz 200 MHz 125 MHz 200 MHz

Item Specification Combinations of SPAN and minimum capture sample SPAN Minimum Capture Sample 1 kHz 74000 (37 s) 2.5 kHz 160000 (32 s) 5 kHz 310000 (31 s) 10 kHz 610000 (30.5 s) 25 kHz 730000 (14.6 s) 50 kHz 730000 (7.3 s) 100 kHz 730000 (3.65 s) 250 kHz 730000 (1.46 s) 500 kHz 730000 (730 ms) 1 MHz 730000 (365 ms) 2.5 MHz 730000 (146 ms) 5 MHz 730000 (73 ms) 10 MHz 730000 (36.5 ms) 18.6 MHz 730000 (36.5 ms) 20 MHz 730000 (29.2 ms) 25 MHz 730000 (14.6 ms) 31.25 MHz 730000 (14.6 ms) 50 MHz 730000 (7.3 ms) 62.5 MHz 730000 (7.3 ms) 100 MHz 730000 (3.65 ms) 125 MHz 730000 (3.65 ms) Phase vs Time Function overview Displays the phase time fluctuation of the input signal in the acquired waveform data. Analysis Time Range Available Mode Analysis Start Time Analysis Time Length Auto, Manual Sets analysis start time position from beginning of waveform data. Sets analysis time span. Phase (Vertical Axis) Display Mode Phase Display Range Offset Wrap, Unwrap 0.01 deg./div to 200 Gdeg./div −100 to 100 Mdeg.

1-44 Table 1.3.1-3 Specifications for spectrum analyzer function Item Specification Frequency SPAN Range Resolution SPAN accuracy 0 Hz, 300 Hz to 3.6 GHz (MS2830A-040) 0 Hz, 300 Hz to 6 GHz (MS2830A-041) 0 Hz, 300 Hz to 13.5 GHz (MS2830A-043) 0 Hz, 300 Hz to 1 MHz (MS2830A-062/066) 0 Hz, 300 Hz to 26.5 GHz (MS2830A-044) 0 Hz, 300 Hz to 43 GHz (MS2830A-045) 2 Hz ±0.2% When number of trace points = 10001 Display frequency accuracy ±[Indicator frequency × reference frequency accuracy + SPAN frequency × SPAN accuracy + RBW × 0.05 + 2 × N + SPAN frequency/(Trace point count–1)] Hz N is Mixing order Resolution bandwidth (RBW) Settable range Selectivity 1 Hz to 3 MHz (1-3 sequence), 500 Hz, 50 kHz, 2 MHz, 5 MHz, 10 MHz, 20 MHz, 31.25 MHz 1 Hz to 10 Hz: Not available when SPAN = 0 Hz 31.25 MHz: Available when SPAN = 0 Hz When MS2830A-045 is installed, only when MS2830A-007 is installed, 20 MHz and 31.25 MHz are available. With MS2830A-062/066 installed, and Option 062/066 enabled: 1 Hz to 100 kHz (–60 dB/–3 dB) 4.5:1, Nominal value, when 1 Hz to 10 MHz is set. Video bandwidth (VBW) Setting range VBW mode 1 Hz to 10 MHz (1-3 sequence), 5 kHz, off Video Average/Power Average

Item Specification Amplitude Display average noise level At 18 to 28ºC, Detector = Sample, VBW = 1 Hz (Video Average), Input attenuator 0 dB, With MS2830A-040/041/043, Without MS2830A-062/066, Without MS2830A-008/108 or with Preamplifier turned off: 9 kHz ≤ frequency < 100 kHz –120 [dBm/Hz] Nominal 100 kHz < frequency < 1 MHz –134 [dBm/Hz] Nominal 1 MHz < frequency < 10 MHz –144 [dBm/Hz] Nominal 10 MHz ≤ frequency < 30 MHz –150 [dBm/Hz] Nominal 100 kHz –134 [dBm/Hz] 1 MHz –144 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –153 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –151 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –149 [dBm/Hz] With MS2830A-041/043 3.5 GHz < frequency ≤ 6 GHz –146 [dBm/Hz] With MS2830A-043 6 GHz < frequency ≤ 13.5 GHz –142 [dBm/Hz] Without MS2830A-062/066, With MS2830A-008/108 and with Preamplifier turned on 100 kHz –147 [dBm/Hz] Nominal 1 MHz –156 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –163 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –162 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –160 [dBm/Hz] With MS2830A-041/043, Frequency Band Mode: Normal 3.5 GHz < frequency ≤ 4 GHz –157 [dBm/Hz] With MS2830A-041/043, Frequency Band Mode: Spurious 3.5 GHz < frequency ≤ 4 GHz –157 [dBm/Hz] With MS2830A-041/043, 4 GHz < frequency ≤ 6 GHz –157 [dBm/Hz] With MS2830A-062/066 installed and inactive, Without MS2830A-008/108 or with Preamplifier turned off: 9 kHz ≤ frequency < 100 kHz –120 [dBm/Hz] Nominal 100 kHz < frequency < 1 MHz –133 [dBm/Hz] Nominal 1 MHz < frequency < 10 MHz –143 [dBm/Hz] Nominal 10 MHz ≤ frequency < 30 MHz –149 [dBm/Hz] Nominal 100 kHz –133 [dBm/Hz] 1 MHz –143 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –152 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –150 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –147 [dBm/Hz] With MS2830A-041/043 installed, 3.5 GHz < frequency ≤ 6 GHz –144 [dBm/Hz] With MS2830A-043 installed, 6 GHz < frequency ≤ 13.5 GHz –142 [dBm/Hz]

1-46 Table 1.3.1-3 Specifications for spectrum analyzer function (Cont’d) Item Specification Display average noise level (Cont’d) With MS2830A-062/066 installed and active, Without MS2830A-008/108 or with Preamplifier turned off: 100 kHz –133 [dBm/Hz] 1 MHz –143 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –152 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –150 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –147 [dBm/Hz] With MS2830A-041/043 installed, 3.5 GHz < frequency ≤ 6 GHz –144 [dBm/Hz] With MS2830A-043 installed, 6 GHz < frequency ≤ 13.5 GHz –142 [dBm/Hz] With MS2830A-062/066 installed, With MS2830A-008/108 and with Preamplifier turned on: 100 kHz –146 [dBm/Hz] Nominal 1 MHz –155 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –162 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –161 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –158 [dBm/Hz] With MS2830A-041/043 installed, Frequency Band Mode: Normal 3.5 GHz < frequency ≤ 4 GHz –154 [dBm/Hz] With MS2830A-041/043 installed, Frequency Band Mode: Spurious 3.5 GHz < frequency ≤ 4 GHz –154 [dBm/Hz] With MS2830A-041/043 installed, 4 GHz < frequency ≤ 6 GHz –154 [dBm/Hz]

Item Specification Display average noise level (Cont’d) With MS2830A-044/045 installed, Without MS2830A-067/167/068/168, Frequency Band Mode: Normal 9 kHz ≤ frequency < 100 kHz –120 [dBm/Hz] Nominal 100 kHz < frequency < 1 MHz –134 [dBm/Hz] Nominal 1 MHz < frequency < 10 MHz –144 [dBm/Hz] Nominal 10 MHz ≤ frequency < 30 MHz –150 [dBm/Hz] Nominal 100 kHz –134 [dBm/Hz] 1 MHz –144 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –153 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –150 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –147 [dBm/Hz] 3.5 GHz < frequency ≤4 GHz –144 [dBm/Hz] 4 GHz < frequency ≤6 GHz –144 [dBm/Hz] 6 GHz < frequency ≤13.5 GHz –151 [dBm/Hz] 13.5 GHz < frequency ≤18.3 GHz –149 [dBm/Hz] 18.3 GHz < frequency ≤26.5 GHz –146 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –146 [dBm/Hz] 34 GHz < frequency ≤40 GHz –144 [dBm/Hz] 40 GHz < frequency ≤43 GHz –140 [dBm/Hz] Without MS2830A-067/167 and with MS2830A-068/168, and with Preamplifier turned off, at Frequency Band Mode: Normal 9 kHz ≤ frequency < 100 kHz –120 [dBm/Hz] Nominal 100 kHz < frequency < 1 MHz –134 [dBm/Hz] Nominal 1 MHz < frequency < 10 MHz –144 [dBm/Hz] Nominal 10 MHz ≤ frequency < 30 MHz –150 [dBm/Hz] Nominal 100 kHz –134 [dBm/Hz] 1 MHz –144 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –153 [dBm/Hz] 1 GHz ≤ frequency < 2.4 GHz –150 [dBm/Hz] 2.4 GHz ≤ frequency ≤ 3.5 GHz –147 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –144 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –144 [dBm/Hz] 6 GHz < frequency ≤ 13.5 GHz –147 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –145 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –141 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –141 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –135 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –132 [dBm/Hz]

1-48 Table 1.3.1-3 Specifications for spectrum analyzer function (Cont’d) Item Specification Display average noise level (Cont’d) Without MS2830A-067/167 or with Microwave Preselector Bypass turned off, and with MS2830A-068/168 and with Preamplifier turned on, at Frequency Band Mode: Normal 100 kHz –147 [dBm/Hz] Nominal 1 MHz –156 [dBm/Hz] 30 MHz ≤ frequency < 1 GHz –163 [dBm/Hz] 1 GHz ≤ frequency < 2 GHz –161 [dBm/Hz] 2 GHz ≤ frequency ≤ 3.5 GHz –159 [dBm/Hz] 3.5 GHz < frequency ≤ 4 GHz –155 [dBm/Hz] 4 GHz < frequency ≤ 6 GHz –155 [dBm/Hz] 6 GHz < frequency ≤ 13.5 GHz –160 [dBm/Hz] 13.5 GHz < frequency ≤ 18.3 GHz –158 [dBm/Hz] 18.3 GHz < frequency ≤ 26.5 GHz –156 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –156 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –150 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –147 [dBm/Hz] Absolute amplitude accuracy After CAL execution at 18 to 28ºC, Auto Sweep Time Select = Normal, 30 Hz ≤ RBW ≤ 1 MHz, Detection = Positive, CW, excluding the noise floor effect, and not when FFT is being executed (displayed on the screen). With Preamplifier turned off: Input attenuator ≥ 10 dB, Mixer input level ≤ –10 dBm With Preamplifier turned on: Input attenuator = 10 dB, preamplifier input level ≤ –20 dBm, With MS2830A-040/041/043 installed, Without MS2830A-008/108, or with Preamplifier turned off ±0.5 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) ±1.8 dB (6 GHz < frequency ≤ 13.5 GHz) With MS2830A-008/108 and with Preamplifier turned on ±1.0 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious)

Item Specification Absolute amplitude accuracy (Cont’d) With MS2830A-044/045 installed, Without MS2830A-068/168 or with Preamplifier turned off: ±0.5 dB (300 kHz ≤frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Spurious) ±1.8 dB (6 GHz < frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (4 GHz < frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±3.0 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±3.0 dB (26.5 GHz < frequency ≤ 40 GHz) ±3.5 dB Nominal (40 GHz < frequency ≤ 43 GHz) With MS2830A-068/168 and with Preamplifier turned on: ±1.0 dB (300 kHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (300 kHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ±1.8 dB (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Spurious) ±2.0 dB (6 GHz < frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (4 GHz < frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±3.0 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±4.0 dB (26.5 GHz < frequency ≤ 40 GHz) ±4.0 dB Nominal (40 GHz < frequency ≤ 43 GHz) The absolute amplitude accuracy is calculated from an RSS (root summed square) error of the RF frequency characteristics, linearity error and input attenuator switching error.

1-50 Table 1.3.1-3 Specifications for spectrum analyzer function (Cont’d) Item Specification Spurious Response Two-tone third-order intermodulation distortion With MS2830A-040/041/043 Without MS2830A-008/108, or with Preamplifier turned off: At 18 to 28°C, with mixer input level = –15 dBm (per tone) and using ≥ 300 kHz separation, at RBW ≤ 30 kHz: ≤ –54 dBc (TOI = +12 dBm) (30 MHz ≤ frequency < 300 MHz) ≤–60 dBc (TOI = +15 dBm) (300 MHz ≤ frequency < 3.5 GHz) ≤–58 dBc (TOI = +14 dBm) (3.5 GHz ≤ frequency ≤ 6 GHz) ≤–50 dBc (TOI = +10 dBm) (6 GHz ≤ frequency ≤ 13.5 GHz) With MS2830A-008/108 installed and with Preamplifier turned on At 18 to 28°C, with Preamplifier input level = –45 dBm (per wave) and using ≥ 300 kHz separation, at RBW ≤30 kHz: ≤–73 dBc (TOI = –8.5 dBm) (30 MHz ≤ frequency < 300 MHz) ≤–78 dBc (TOI = –6 dBm) (300 MHz ≤ frequency ≤ 700 MHz) ≤–81 dBc (TOI = –4.5 dBm) (700 MHz ≤ frequency < 4 GHz, Frequency Band Mode: Normal) (700 MHz ≤ frequency < 3.5 GHz, Frequency Band Mode: Spurious) ≤–78 dBc (TOI = –6 dBm) (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Spurious) With MS2830A-044/045 installed Without MS2830A-068/168 or with Preamplifier turned off, At 18 to 28°C, with mixer input level = –15 dBm (per wave) and using ≥ 300 kHz separation, at RBW ≤30 kHz: ≤–54 dBc (TOI = +12 dBm) (30 MHz ≤ frequency < 300 MHz) ≤–60 dBc (TOI = +15 dBm) (300 MHz ≤ frequency < 3.5 GHz) ≤–58 dBc (TOI = +14 dBm) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) ≤–56 dBc (TOI = +13 dBm) (6 GHz < frequency ≤ 13.5 GHz) ≤–56 dBc (TOI = +13 dBm) (13.5 GHz < frequency ≤ 26.5 GHz) ≤–56 dBc (TOI = +13 dBm) Nominal (26.5 GHz < frequency ≤ 40 GHz) With MS2830A-045 installed

Item Specification Two-tone third-order intermodulation distortion (Cont’d) With MS2830A-044/045 installed With MS2830A-067/167 and with Microwave Preselector Bypass turned off, and with MS2830A-068/168 and with Preamplifier turned on, At 18 to 28°C, with Preamplifier input level = –45 dBm (per wave) and using ≥ 300 kHz separation, at RBW ≤ 30 kHz: ≤–73 dBc (TOI = –8.5 dBm) (30 MHz ≤ frequency < 300 MHz) ≤–78 dBc (TOI = –6 dBm) (300 MHz ≤ frequency ≤ 700 MHz) ≤–81 dBc (TOI = –4.5 dBm) (700 MHz < frequency < 4 GHz, Frequency Band Mode: Normal) (700 MHz < frequency < 3.5 GHz, Frequency Band Mode: Spurious) ≤–78 dBc (TOI = –6 dBm) (4 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal) (3.5 GHz ≤ frequency ≤ 4 GHz, Frequency Band Mode: Spurious) ≤–70 dBc (TOI = –10 dBm) (6 GHz < frequency ≤ 13.5 GHz, Frequency Band Mode: Normal) (4 GHz < frequency ≤ 13.5 GHz, Frequency Band Mode: Spurious) ≤–70 dBc (TOI = –10 dBm) (13.5 GHz < frequency ≤ 26.5 GHz) ≤–70 dBc (TOI = –10 dBm) Nominal (26.5 GHz < frequency ≤ 40 GHz) With MS2830A-045 installed When Attenuator Mode is E-ATT Combined: Without MS2830A-008/108/068/168 and with Preamplifier turned off, at 18 to 28°C, with mixer input level = –15 dBm (per wave) and using ≥ 300 kHz separation, at RBW ≤30 kHz: ≤–54 dBc (TOI = +12 dBm) (30 MHz≦frequency < 300 MHz, RF input level ≤ –5 dBm) ≤–60 dBc (TOI = +15 dBm) (300 MHz≦frequency ≤ 1 GHz, RF input level ≤ –5 dBm) ≤–60 dBc (TOI = +15 dBm) (1 GHz < frequency < 3.5 GHz, RF input level ≤ +5 dBm) ≤–58 dBc (TOI = +14 dBm) (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal, RF input level ≤ +5 dBm) ≤–54 dBc (TOI = +12 dBm) Nominal (30 MHz≤ frequency < 300 MHz, RF input level ≤0 dBm) ≤–60 dBc (TOI = +15 dBm) Nominal (300 MHz ≤ frequency < 3.5 GHz, RF input level ≤+15 dBm) ≤–58 dBc (TOI = +14 dBm) Nominal (3.5 GHz ≤ frequency ≤ 6 GHz, Frequency Band Mode: Normal, RF input level ≤+15 dBm)

1-52 Table 1.3.1-3 Specifications for spectrum analyzer function (Cont’d) Item Specification Image response With MS2830A-040/041/043 installed, Frequency Band Mode: Normal ≤–70 dBc (10 MHz ≤ frequency < 4 GHz) ≤–55 dBc (4 GHz ≤ frequency ≤ 6 GHz) ≤–60 dBc (6 GHz < frequency ≤ 13.5 GHz) With MS2830A-062 installed and operating (Opt-062 enabled, 3.6 GHz max. center frequency, ≤1 MHz SPAN as spectrum analyzer) ≤–10 dBc (This is generated at “input signal + 150 MHz”.) (330 MHz ≤ frequency < 3.6 GHz) With MS2830A-066 installed and operating (066: Enabled, Center frequency: 3.6 GHz or less, and SPAN ≤ 1 MHz as spectrum analyzer). ≤ –10 dBc (This is generated at “input signal + 150 MHz”.) (110 MHz ≤ frequency < 3.6 GHz) With MS2830A-044/045 installed, When MS2830A-067/167 is NOT installed ≤–70 dBc (10 MHz ≤ frequency < 4 GHz) ≤–55 dBc (4 GHz ≤ frequency ≤ 6 GHz) ≤–70 dBc (6 GHz < frequency ≤ 13.5 GHz) ≤–70 dBc (13.5 GHz < frequency ≤ 26.5 GHz) Multiple Response (330 MHz ≤ Frequency < 3.6 GHz With MS2830A-040/041/043 installed, With MS2830A-062/066 installed and operating (Opt-062/066 enabled, 3.6 GHz max. center frequency, SPAN ≤ 1 MHz as spectrum analyzer), and –15 dBm mixer input level ≤–10 dBc Nominal

Item Specification Sweep Sweep mode Single, Continuous Sweep time Setting range 1 ms to 1000 s (SPAN ≥ 300 Hz) 1 µs to 1000 s (SPAN = 0 Hz) Detection mode Pos&Neg, Positive Peak, Sample, Negative Peak, RMS The number of trace points When SPAN > 30 GHz: 5001, 10001, 30001 When 500 MHz < SPAN ≤ 30 GHz: 1001, 2001, 5001, 10001, 30001 When 300 Hz≤ SPAN ≤100 MHz and Sweep Time > 10 s: 101, 201, 251, 401, 501, 1001, 2001, 5001, 10001, 30001 When 300 Hz≤ SPAN ≤100 MHz and Sweep Time ≤ 10 s: 11, 21, 41, 51, 101, 201, 251, 401, 501, 1001, 2001, 5001, 10001, 30001 When Span = 0 Hz: 11, 21, 41, 51, 101, 201, 251, 401, 501, 1001, 2001, 5001, 10001, 30001 Scale Log indicator Lin indicator 10div/12div : 0.1 to 20 dB/div, 1-2-5 sequence 10div : 1 to 10%/div, 1-2-5 sequence Trigger function Trigger mode Free Run (Trig Off), Video, Wide IF Video, External, Frame SG Marker (With MS2830A-020/120/021/121) Gate function Gate mode Off, Wide IF Video, External, Frame SG Marker (With MS2830A-020/120/021/121)

1-54 Table 1.3.1-3 Specifications for spectrum analyzer function (Cont’d)) Item Specification Measurement function Adjacent Channel Power Measurement (ACP) Reference Adjacent channel specification Span Total, Carrier Total, Both Sides of Carriers or Carrier Select 3 channels × 2 (Normal Mode) 8 channels × 2 (Advanced Mode) Burst arrange Indicates average power of specified time in the time domain mode. Channel Power Absolute value measurement dBm, dBm/Hz Occupied Bandwidth (OBW) N% of Power method, X dB Down method Spectrum Emission Mask (SEM) Peak/Margin measurement: Pass/fail judgment is performed by Peak/Margin measurement. Spurious Emission Worst/Peaks measurement: Pass/fail judgment is performed by Worst/Peaks measurement Frequency counter Counter accuracy ±(marker frequency × reference frequency accuracy + (0.1 × N/Gate Time[s])) Hz) at SPAN ≤ 1 MHz, RBW = 1 kHz, S/N ≤ 50 dB, Gate Time ≥ 100 ms Mixer harmonic order [N] Two-tone third-order intermodulation distortion Measures IM3 and TOI from two-tone signal. 1.3.2 Rubidium Reference Oscillator Option (MS2830A-001/101) Table 1.3.2-1 Rubidium Reference Oscillator Specifications Items Specifications Function and Performance See Table 1.3.1-1, “Internal reference oscillator”. 1.3.3 High Stability Reference Oscillator Option (MS2830A-002/102) Table 1.3.3-1 High Stability Reference Oscillator Option Specifications Item Specification Function and Performance See Table 1.3.1-1, “Internal reference oscillator”. Others This option is not available when MS2830A-044/045 is installed.

Table 1.3.4-1 lists the specifications for the preamplifier. The following specification values are those under the conditions after 30-min warm-up at stable ambient temperature. Typical values are only for reference and are not guaranteed. Table 1.3.4-1 Preamplifier Option Specifications Item Specification Frequency Frequency range 100 kHz to 3.6 GHz (With MS2830A-040) 100 kHz to 6 GHz (With MS2830A-041/043) Amplitude Measurement range See Table 1.3.1-1, “Measurement range”. Maximum input level See Table 1.3.1-1, “Maximum input level”. Display average noise level (Signal Analyzer function) See Table 1.3.1-2, “Display average noise level”. Display average noise level (Spectrum analyzer function) See Table 1.3.1-3, “Display average noise level”. RF Frequency Characteristics See Table 1.3.1-1, “RF frequency characteristics”. Input attenuator switching error See Table 1.3.1-1, “Input attenuator switching error”. Linearity error See Table 1.3.1-1, “Linearity error”. Secondary harmonic wave distortion See Table 1.3.1-1, “Secondary harmonic wave distortion”. 1 dB gain compression See Table 1.3.1-1, “1 dB gain compression”. Two-tone third-order intermodulation distortion See Table 1.3.1-3, “Two-tone third-order intermodulation distortion”. Others Cannot install simultaneously with MS2830A-068/168.

1-56 1.3.5 Analysis Bandwidth Extension to 31.25 MHz Option (MS2830A-005/105) Table 1.3.5-1 Analysis Bandwidth Extension to 31.25 MHz Option Specifications Item Specification Function and Performance Function to analyze 31.25 MHz bandwidth Others This option is not available when MS2830A-045 is installed. 1.3.6 Analysis Bandwidth Extension to 10 MHz Option (MS2830A-006/106) Table 1.3.6-1 Analysis Bandwidth Extension to 10 MHz Option Specifications Item Specification Function and Performance Function to analyze 10 MHz bandwidth 1.3.7 Phase Noise Measurement Option (MS2830A-010/110) Table 1.3.7-1 Phase Noise Measurement Function Specifications Item Specification Function Displays the phase noise characteristics on a logarithmic scale. Frequency Range Offset frequency range 10 MHz to Upper frequency limit 10 Hz to 10 MHz Marker Mode Normal, Integral Noise, RMS Noise, Jitter, Residual FM, Off 1.3.8 Secondary HDD Option (MS2830A-011/111) Table 1.3.8-1 Secondary HDD Option Specifications Item Specification Use Removable HDD for storing user data Insert into the HDD (Opt) slot on the back panel to use. Figure 3.1.1-2 Rear panel “16 HDD slot for options” 1.3.9 Precompliance EMI Function (MS2830A-016/116) Table 1.3.9-1 Precompliance EMI Function Option Specifications Item Specification Function Adds the Detection Mode and the Resolution Bandwidth for EMI measurement to the Spectrum Analyzer function. Detection Mode (CISPR Detector) Quasi-Peak, CISPR-AVG, RMS-AVG Resolution Bandwidth (CISPR RBW) 200 Hz (6 dB BW), 9 kHz (6 dB BW), 120 kHz (6 dB BW), 1 MHz (Impulse)

Summary: The SSB phase noise is improved for RF input signals by provision of an internal dedicated frequency converter. Near-carrier phase noise is reduced by installing the Low Phase Noise option (MS2830A-062/066) and turning On the Low Phase Noise option function. Example of Improvement: The Low Phase Noise Performance option brings the following improvements in the measurement of narrow-band radio device (radio for commercial use) and of transmitter for digital TV broadcasting. ・ Allows near-carrier spurious measurement. ・ The adjacent channel power (ACP) measurement is performed with accuracy because noise power over the adjacent channel is reduced. ・ S/N and EVM are improved due to reduced residual FM. Precautions when Low Phase Noise option enabled (On). The operation principle of the frequency converter is generation of a spurious response at a specific frequency. As a result, sometimes it is better not to use, such as when measuring spurious. When the DUT signal frequency is known, when the MS2830A Rx frequency is set to 35 MHz beyond that frequency, measurement can be made as if the Low Phase Noise Function is Off (disabled) because the spurious response cannot be observed. However, even if the DUT signal frequency is unknown, measurement can be made after setting the Low Phase Noise Function to Off (disabled) and verifying the presence of a response at about the same level (in other words, confirming that the observed signal has the correct response). The spurious responses are as follows: (1) Image Response This response is generated when a signal with frequency fin is input to the MS2830A RF input connector and the MS2830A Rx frequency is set to fin –150 MHz, and more than 330 MHz (with MS2830A-062) or more than 110 MHz (with MS2830A-066). The generated level is about –20 dBc.

1-58 (2) Multiple Response This response is generated when a signal with frequency fin is input to the MS2830A RF input connector and the MS2830A Rx frequency is set to (fin ±75 MHz)/N–75 MHz (N = 1,2,3 …),and more than 330 MHz (with MS2830A-062) or more than 110 MHz (with MS2830A-066). The generated level is about –10 dBc. Table 1.3.10-1 Low Phase Noise Performance Specifications Item Specification Frequency Frequency Range 9 kHz to 3.7 GHz 9 kHz to 3.5 GHz (Frequency Band Mode: Spurious) SPAN 1 kHz to 31.25 MHz (Signal Analyzer function) 300 Hz to 1 MHz (Spectrum Analyzer function) Single side band noise See Table 1.3.1-1, “Single side band noise”. Resolution bandwidth (RBW) See Table 1.3.1-3, “Specifications for spectrum analyzer function, Resolution bandwidth (RBW)”. Amplitude Display average noise level (Signal Analyzer function) See Table 1.3.1-2, “Specifications for Signal Analyzer Function, Display average noise level”. Display average noise level (Spectrum analyzer function) See Table 1.3.1-3, “Specifications for spectrum analyzer function, Display average noise level”. Spurious Response Image response See Table 1.3.1-3, “Specifications for spectrum analyzer function, Image response”. 1.3.11 Removable HDD option (MS2830A-313) Table 1.3.11-1 Removable HDD Option Specification Item Specification Use This is a spare hard disk for the MS2830A to replace the disk. Insert into the HDD slot on the back panel to use. Figure 3.1.1-2 Rear panel “15 HDD slot”

This option amplifies signal prior to 1st mixer to enhance sensitivity. This option is the wideband version of Preamplifier Option (MS2830A-008/108), and can be used on the application software in a similar way. Table 1.3.12-1 Microwave Preamplifier Option Specifications Item Specification Frequency Frequency range 100 kHz to 26.5 GHz (With MS2830A-044) 100 kHz to 43 GHz (With MS2830A-045) Amplitude Measurement range See Table 1.3.1-1, “Measurement range”. Maximum input level See Table 1.3.1-1, “Specifications for Mainframe, Maximum input level”. Display average noise level (Signal Analyzer function) See Table 1.3.1-2, “Specifications for Signal Analyzer Function, Display average noise level”. Display average noise level (Spectrum analyzer function) See Table 1.3.1-3, “Display average noise level”. RF Frequency Characteristics See Table 1.3.1-1, “Specifications for Mainframe, RF frequency characteristics”. Input attenuator switching error See Table 1.3.1-1, “Specifications for Mainframe, Input attenuator switching error”. Linearity error See Table 1.3.1-1, “Specifications for Mainframe, Linearity error”. Secondary harmonic wave distortion See Table 1.3.1-1, “Specifications for Mainframe, Secondary harmonic wave distortion”. 1 dB gain compression See Table 1.3.1-1, “Specifications for Mainframe, 1 dB gain compression”. Two-tone third-order intermodulation distortion See Table 1.3.1-3, “Specifications for spectrum analyzer function, Two-tone third-order intermodulation distortion”. Others Cannot install simultaneously with MS2830A-008/108.

1-60 1.3.13 Microwave Preselector Bypass Option (MS2830A-067/167) Summary: By bypassing the preselector (image response elimination filter), the RF frequency characteristics and the in-band frequency characteristics are improved, and level accuracy improvement can be achieved. Notes on default values when this option is installed: To improve the in-band frequency characteristics, the default value is set to On for the Signal Analyzer function, and is always set to On for all other applications. To avoid measuring the image signals generated internally, the default value is set to Off for the Spectrum Analyzer function. Table 1.3.13-1 Microwave Preselector Bypass Option Specifications Item Specification Intended Use Bypasses the preselector to improve the RF frequency characteristics and the in-band frequency characteristics. When this function is set to On, the image response elimination filter is bypassed. Therefore, this function is not appropriate for image response reception and spurious measurement. Function and performance Frequency Frequency range 4 GHz to 26.5 GHz (MS2830A-044) 4 GHz to 43 GHz (MS2830A-045) Amplitude RF frequency characteristics After CAL execution at 18 to 28ºC, input attenuator = 10 dB, With Microwave Preselector Bypass turned on, Without MS2830A-068/168 or with Preamplifier turned off: ±1.00 dB (6 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (4 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±1.50 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±2.00 dB (26.5 GHz < frequency ≤ 40 GHz) ±2.00 dB typ. (40 GHz < frequency ≤ 43 GHz)

Item Specification RF frequency characteristics (Cont’d) With Microwave Preselector Bypass turned on, With MS2830A-068/168 or with Preamplifier turned on: ±1.8 dB (6 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Normal) (4 GHz ≤ frequency ≤ 13.8 GHz, Frequency Band Mode: Spurious) ±2.50 dB (13.8 GHz < frequency ≤ 26.5 GHz) ±3.00 dB (26.5 GHz < frequency ≤ 40 GHz) ±3.00 dB Nominal (40 GHz < frequency ≤ 43 GHz) Display average noise level At 18 to 28ºC, Detector = Sample, VBW = 1 Hz (Video Average) At input attenuator 0 dB, Irrespective of Microwave Preselector Bypass turned on/off, Without MS2830A-068/168 installed, With MS2830A-044/045, 6 GHz < frequency ≤ 13.5 GHz –147 [dBm/Hz] 13.5 GHz < frequency ≤ 18.4 GHz –145 [dBm/Hz] 18.4 GHz < frequency ≤ 26.5 GHz –141 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –141 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –135 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –132 [dBm/Hz] With MS2830A-068/168 or with Preamplifier turned off: With MS2830A-044/045, 6 GHz < frequency ≤ 13.5 GHz –142 [dBm/Hz] 13.5 GHz < frequency ≤ 18.4 GHz –140 [dBm/Hz] 18.4 GHz < frequency ≤ 26.5 GHz –136 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –136 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –131 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –128 [dBm/Hz]

1-62 Table 1.3.13-1 Microwave Preselector Bypass Option Specifications (Cont’d) Item Specification Display average noise level (Cont’d) With Microwave Preselector Bypass turned on, With MS2830A-068/168 and with Preamplifier turned on: With MS2830A-044/045, 6 GHz < frequency ≤ 13.5 GHz –154 [dBm/Hz] 13.5 GHz < frequency ≤ 18.4 GHz –152 [dBm/Hz] 18.4 GHz < frequency ≤ 26.5 GHz –150 [dBm/Hz] With MS2830A-045, 26.5 GHz < frequency ≤ 34 GHz –150 [dBm/Hz] 34 GHz < frequency ≤ 40 GHz –144 [dBm/Hz] 40 GHz < frequency ≤ 43 GHz –141 [dBm/Hz] Image response With Microwave Preselector Bypass turned off, –60 dBc (6 GHz < frequency ≤ 13.5 GHz) –60 dBc (13.5 GHz < frequency ≤ 13.5 GHz) With Microwave Preselector Bypass turned on, Generated at the frequency at the distance of 1875 MHz × 2 0 dBc Nominal (4 GHz < frequency ≤ 26.5 GHz) 0 dBc Nominal (26.5 GHz < frequency ≤ 43 GHz) Others Cannot be installed together with MS2830A-007 1.3.14 Bandwidth Extension to 31.25 MHz with Preselector Bypass Option (MS2830A-007) This option adds a function to analyze 31.25 MHz bandwidth and a preselector option to Option 045. It can be used in a similar way as Option 005/105 and Option 067/167 on the application software. Table 1.3.14-1 Bandwidth Extension to 31.25 MHz with Preselector Bypass - Option Specifications Item Specification Application This option adds a function to analyze 31.25 MHz bandwidth and a preselector option to Option 045 (43 GHz Signal Analyzer). When the preselector option is set to On, the image response elimination filter is bypassed. Therefore, this function is not appropriate for image response reception and spurious measurement. Function and performance Display average noise level Refer to Table 1.3.13-1 “Microwave Preselector Bypass Option Specifications: Display average noise level.” RF frequency characteristics Refer to Table 1.3.13-1 “Microwave Preselector Bypass Option Specifications: RF frequency characteristics.” Others Cannot be installed together with MS2830A-067/167. Available only when MS2830A-045 is installed.

(MS2830A-077/177) Table 1.3.15-1 Analysis Bandwidth Extension to 62.5 MHz Option Specifications Item Specification Application Extends the analysis bandwidth to 62.5 MHz in single analyzer mode by bypassing a bandwidth-limiting filter such as a preselector and performing fast sampling. On the other hand, because an image response is received due to bypassing the image response elimination filter, this is not adequate for measuring spurious or out-of-analysis-band signals and analyzing signals. ADC resolution 14 bits Image response With MS2830A-077/177 installed and Bandwidth > 31.25 MHz. To be generated at a frequency that is 200 MHz away. 0 dBc Nominal (300 MHz < frequency ≤ 43 GHz) With MS2830A-077/177 and MS2830A-067/167 installed and Bandwidth > 31.25 MHz. To be generated at a frequency that is 1875 MHz × 2 away. 0 dBc Nominal (6 GHz < frequency ≤ 43 GHz) Others

1-64 1.3.16 Analysis Bandwidth Extension Option, 125 MHz (MS2830A-078/178) Table 1.3.16-1 Analysis Bandwidth Extension to 125 MHz Option Specifications Item Specification Application Extends the analysis bandwidth to 125 MHz in single analyzer mode by bypassing a bandwidth-limiting filter such as a preselector and performing fast sampling. On the other hand, because an image response is received due to bypassing the image response elimination filter, this is not adequate for measuring spurious or out-of-analysis-band signals and analyzing signals. ADC resolution 14 bits Image response With MS2830A-078/178 installed and Bandwidth > 31.25 MHz. To be generated at a frequency that is 200 MHz away. 0 dBc Nominal (300 MHz < frequency ≤ 43 GHz) With MS2830A-078/178 and MS2830A-067/167 installed and Bandwidth > 31.25 MHz. To be generated at a frequency that is 1875 MHz × 2 away. 0 dBc Nominal (6 GHz < frequency ≤ 43 GHz) Others 1.3.17 Bandwidth Extension to 31.25 MHz for Millimeter-wave (MS2830A-009/109) Table 1.3.17-1 Bandwidth Extension to 31.25 MHz for Millimeter-wave Specifications Item Specification Application Extends the analysis bandwidth to 31.25 MHz in signal analyzer mode. Others This option is available only when MS2830A-045 is installed.

Table 1.3.18-1 BER Measurement function Specifications Item Specification Connector Rear panel Aux connector Input level TTL level Input signal Data, Clock, Enable Input bit rate 100 bps to 10 Mbps Measurable patterns PN9, PN11, PN15, PN20, PN23, ALL0, ALL1, repetition of 01 PN9Fix, PN11Fix, PN15Fix, PN20Fix, PN23Fix UserDefine (4096 bits max.) Synchronization establishing condition PN signal: No error has been detected for (PN stage count × 2) bits PNFix signal: Synchronization with the PN signal is established if no error has been detected for (PN stage count × 2) bits. Next, the cycle and synchronization of the PNFix signal are established if no error has been detected for PN stage count bits beginning with the start bit of the PNFix signal. ALL0, ALL1, repetition of 01: No error has been detected for 10 bits. UserDefine: No error has been detected for 8 to 1024 bits (variable). The start bit used for synchronization detection can also be selected. Re-synchronization judgment condition x/y (Resynchronization is executed if x bits out of y bits are errors.) y (Measurement bit count): Selected from 500 bits, 5000 bits, and 50000 bits x (Error bit count out of y bits): 1 to y/2 bits Measurable bit count ≤ 232 − 1 bits Measurable error bit count ≤ 231 − 1 bits Measurement termination condition Measurement bit count, measurement error bit count Auto Resync function Can be switched between enable/disable. Count operation at resynchronization Can be selected from Count Clear and Count Keep. Measurement mode Continuous, Single, Endless Display Status, Error, Sync Loss, Error Rate, Error Count, SyncLoss Count Measurement bit count Polarity reversal function Data, Clock, and Enable polarities can be reversed. Measured value clear function It is possible to clear the measured values to 0 while retaining synchronization during BER measurement, and start the measurement again from 0.

1-66 1.3.19 Audio Analyzer Option (MS2830A-018/118) This option adds the audio generator and audio analyzer function. For specifications of the Audio Analyzer, refer to the MX269018A Analog Measurement Software/MS2830A Signal Analyzer Analog Signal Generator Operation Manual. 1.3.20 Two-handle Frame with Connecting Parts (for Single-handle Frame) (MS2830A-171) This is an option to connect singled-handled MS2830A with a measurement module like the MN2555A Duplexer Box. 1.3.21 Connecting parts (for two-handle frame) (MS2830A-081/181) This is an option to connect doubled-handled MS2830A with a measurement module like the MN2555A Duplexer Box. 1.3.22 3.6 GHz Analog Signal Generator Option (MS2830A-088/188) Table 1.3.22-1 3.6 GHz Analog Signal Generator Option Specifications Item Specification Application Adds the analog signal generator function to MS2830A. 1.3.23 Vector Function Extension for Analog Signal Generator Option (MS2830A-189) Table 1.3.23-1 Vector Function Extension for Analog Signal Generator Option Specifications Item Specification Application Adds the vector modulation function to MS2830A-088/188.

(MS2830A-052/152/352) Table 1.3.24-1 Internal Signal Generator Control Function Option Specifications Item Specification Application The DUT transfer characteristics can be measured by interlinking the internal signal generator and spectrum analyzer operations. Others This option is available only when one of the following options is installed. MS2830A-020/120, MS2830A-021/121, MS2830A-088/188 User needs to install the license before using the MS2830A-352 Internal Signal Generator Control Function User-installable. For how to install the license, refer to “Installing software or licenses” in 3.8.1 “Installing software or hardware licenses”.

MS2830A. Be sure to read this section at least once as it contains safety tips and cautions for avoiding failure during use. 2.1 Installation Location ...................................................... 2-2 2.1.1 Installation orientation....................................... 2-2 2.1.2 Distance from surrounding objects ................... 2-3 2.1.3 Installation location conditions .......................... 2-3 2.2 Items to Check Before Use ........................................... 2-4 2.2.1 Safety labels ..................................................... 2-4 2.2.2 Input level and reverse power (when vector signal generator is installed) to RF Input ....... 2-5 2.2.3 Electrostatic ...................................................... 2-6 2.2.4 Notes on handling input connector and SG output connector (when vector signal generator is installed) ....................................... 2-8 2.2.5 USB memory stick ............................................ 2-8 2.3 Power Connection ........................................................ 2-9 2.3.1 Power requirements ......................................... 2-9 2.3.2 Connecting power cord..................................... 2-9

2-2 2.1 Installation Location 2.1.1 Installation orientation Install the MS2830A horizontally or at an angle using the tilted legs as shown in Figure 2.1.1-1. Do not place objects on top of the MS2830A when tilted. Figure 2.1.1-1 Installation orientation CAUTION If the MS2830A is not installed in a “OK” direction as above, a small shock may turn it over and harm the user. NG OK

A fan is installed to the MS2830A to prevent the internal temperature from rising. Install the MS2830A in a location with the vents at least 10 cm away from walls, peripherals or other obstructions so as not to block the fan perimeter. Figure 2.1.2-1 Distance from surrounding objects 2.1.3 Installation location conditions Although the MS2830A operates at an ambient temperature of 5° to 45°C, avoid using it in locations, such as the following, since it may cause failure. ● Locations with strong vibrations ● Humid and dusty locations ● Locations with direct sunlight ● Locations where there is the risk of exposure to active gases ● Locations where power voltage severely fluctuates At least 10 cm space At least 10 cm space At least 10 cm space At least 10 cm space

2-4 2.2 Items to Check Before Use 2.2.1 Safety labels To protect the safety of the user, the WARNING label shown in Figure 2.2.1-1 is affixed to the rear panel. Observe the instructions on the label. Figure 2.2.1-1 Warning labels WARNING THIS MEASURING EQUIPMENT IS A PRECISION ELECTRONIC DEVICE THAT CONTAINS HAZARDOUS PARTS, AND THEREFORE MUST NOT BE SERVICED BY THE CUSTOMER. UNDER NO CIRCUMSTANCES DISASSEMBLE THIS EQUIPMENT. THIS EQUIPMENT MUST BE SERVICED ONLY BY QUALIFIED SERVICE PERSONNEL.

2-5 2 Before Use 2.2.2 Input level and reverse power (when vector signal generator is installed) to RF Input The MS2830A is not provided with over-power protection. Be careful not to apply the power to the RF Input connector as described below: For Option 040/041/043, without Option 008/108 installed, or with Preamplifier turned off: +30 dBm Max (Input attenuator ≥10 dB), ±10 Vdc Max For Option 040/041/043, with Option 008/108 installed, and with Preamplifier turned on: +10 dBm Max (Input attenuator = 0 dB), ±10 Vdc Max For Option 044/045, without Option 068/168 installed, or with Preamplifier turned off: +30 dBm Max (Input attenuator ≥ 10 dB), ±0 Vdc Max For Option 044/045, with Option 068/168 installed, and with Preamplifier turned on: +10 dBm Max (Input attenuator = 0 dB), ±0 Vdc Max There is no reverse power protection for the SG output connector when the Vector Signal Generator Option is installed. Be careful not to apply reverse power to the SG Output connector as described below: When Option 022/122 is NOT installed: +12 dBm Max (<20 MHz), +24 dBm Max (≥20 MHz) When Option 022/122 is installed: +18 dBm Max (<20 MHz), +30 dBm Max (≥20 MHz) In addition, do not apply DC voltage even when within the range described above.

2-6 2.2.3 Electrostatic CAUTION ● Always use the supplied 3-pin power cord to ground both the MS2830A and DUT (included in test circuit). After confirming that both the MS2830A and DUT are grounded, use coaxial cables to connect them. NEVER connect the MS2830A and DUT without grounding, otherwise electrostatic discharge may damage the MS2830A. ● Do not touch the core conductor of the connector or bring it into contact with metal. Doing so may damage the input circuit of the MS2830A.