Aria A4601 Instructions

workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by ChannelVisionTechnology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date willberequiredbeforewarrantyrepairsareprovided. Mail in service can be obtained during the warranty period by calling (800) 840- 0288 toll free. A Return Authorization number must be obtained in advance and canbemarkedontheoutsideoftheshippingcarton. This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorizedservicecenter. 500-059 rev E Specifications: (typical @25º C) Audio Video Bandwidth: Crosstalk: Dynamic Range: THD: Bandwidth: Crosstalk: 20-20kHz -90 dB 6.0 Vp-p 0.01% DC-20MHz -60 dB Specifications subject to change without notice. A4601 A4601R 4x6 Matrix Switcher By Aria By Channel Vision 4x6 Matrix Switcher A4601 Aria By Channel Vision 4x6 Matrix Switcher A4601

whole-house audio systems. The unit is organized into 4 audio/video inputs and 6 audio/video outputs. The A4601 is intended to be used with a multichannel audio amplifier, such as the A1260. Any of the 4 source inputs can be selected and routed to any of the 6 outputs (or zones) independent of the other zones through the use of an IR repeating keypad (such as the A0127- Sold separately). The A4601R is equipped with a rack mount faceplate to allow installations in a standard 19” equipment rack. Control of the A4601... is accomplished through the use of an IR repeating device, such as the A0127 keypad. The A0127 already contains the IR codes necessary to operate the A4601, but you may also use a standard IR receiver or a 3rd party keypad. When using a simple IR receiver, you will need to program a learning remote control with the IR codes for the A4601. These codes can be downloaded from www.channelvision.com, or learned from an A0127. A4601/A4601R 4x6 A/V matrix controller Aria By Channel Vision 4x6 Matrix Switcher A4600 Aria By Channel Vision 4x6 Matrix Switcher A4600 Pwr Mute Vid 1 Vid 2 Vid 3 Vid 4 Vol + Vol - A0127 IR-2001 IR-2202 C HANNEL V ISION TM S O U R C E ZONE POWER MUTE VOL 1 2 3 4 MODEL A0501 POWER C HANNEL V ISION TM S O U R C E ZONE POWER MUTE VOL 1 2 3 4 MODEL A0501 POWER Pwr Mute Vid 1 Vid 2 Vid 3 Vid 4 Vol + Vol - 7 Using the A0501 remote control... The A0501 is designed to allow you to control your A4601 without having to touch the buttons on the A0127. Simply point the A0501 remote control at the IR sensor located at the bottom of the A0127 and press the desired button. Downloading IR commands for the A4601... If you don’t have access to the A0501 remote and you need to program a learning remote, you can download the IR codes from the internet. IR codes compatible with the Philips Pronto remote controls can be downloaded from the following websites: www.channelvision.com (Hex codes are also available) www.remotecentral.com Zone Power - Turns on/off the zone you are in Power - Master power for A4601 (turns all zones on/off) Mute - Mutes the audio for the zone you are in VOL - Controls volume for the zone you are in Source Buttons

Keypads connect to the A4601 through the RJ45 jacks on the back panel of the A4601. Connections to the A0127 may be accomplished either by using the RJ45 jack or the screw terminals provided on the back side of the keypad. When using the RJ45 jacks, simply wire both ends of the cable according to the TIA568A standard. When using the screw terminals on the A0127, make sure to wire the RJ45 plug connecting to the A4601 as shown below. Connecting a standard IR repeater to the A4601... A standard IR repeating device may be connected directly to the A4601 allowing the unit to be controlled from a learning IR remote. The connection is similar to the wiring configuration shown above for the A0127, except there are only three wires as shown below. Note: not all IR receivers have the voltage, ground, and signal connections in the same order as this diagram. Pin 8: +VDC, Pin 7: Ground, Pin 4: IR. A0127 A4601 Front Rear Pin 7: Ground Pin 8: +VDC Pin 4: IR signal Pin 8: +VDC Pin 7: Ground Pin 4: IR signal N.C. Typical IR receiver connection Pin 8: +VDC Pin 7: Ground Pin 4: IR signal Pwr Mute Vid 1 Vid 2 Vid 3 Vid 4 Vol + Vol - Pin 8: +VDC Pin 7: Ground Pin 4: IR signal Pwr Mute Vid 1 Vid 2 Vid 3 Vid 4 Vol + Vol - How IR repeating works AB-500 Tx Batt Rew<< Play> FF>> Learn Stop Pause 1 2 3 4 5 6 7 8 9 0 Power -/-- Ch Vol Learn Error All Off Off Select Tuner CD Sat VCR DVD TV Channel Vision TM Point any IR remote control at an IR receiver (such as the A0127 shown here). CD player And the flasher repeats the IR signal in the other room. Many IR receiving devices provide an indication that an IR command has been received. On the A0127, the Pwr button flashes as IR information is received. Be sure the flasher is attached directly over the component’s IR receiver. 3 Accessories IR-3003 & IR-3002 ... Single and dual head IR flashers. Use one head per source to control from the remote room. (IR-3002 shown). AB-500 Tx Batt Rew<< Play> FF>> Learn Stop Pause 1 2 3 4 5 6 7 8 9 0 Power -/-- Ch Vol Learn Error All Off Off Select Tuner CD Sat VCR DVD TV Channel Vision TM AB-500 ... Universal remote control.. Learns IR codes for up to 6 sources. A0127 ... IR repeating keypad. Preprogrammed to control the A4601 and is capable of teaching its commands to a learning IR remote control. Pwr Mute Vid 1 Vid 2 Vid 3 Vid 4 Vol + Vol -

Channel Vision A4601 Tested To Comply With FCC Standards R-Audio-L Video R-Audio-L Video R-Audio-L 3 4 6 5 OUTPUTS OUT OUTPUTS 6 Control 5 4 Control 3 2 4 A4601 Re 120 240 R L 6 SPKR IN Local Global R L 5 SPKR IN Local Global Global 10A 120V 5A 240V Slow Blow 10A 120V 5A 240V Slow Blow Input Voltage CAUTI RISK OF ELECTR DO NOT O 120 V~ 60 Hz 240 V~ 50 Hz 1000 W 120 V~ 60 Hz 240 V~ 50 Hz 1000 W A1260 XXXX A1260 XXXX A1260 Re See page 6 for connection details Pwr Mute Vid 1 Vid 2 Vid 3 Vid 4 Vol + Vol - Room 6 Each zone is controlled through the A0127 keypad which connects to the RJ45 jacks on the rear panel. INPUTS Power 230 / 115 VAC 50 / 60 Hz Input Voltage 3 R-Audio-L Video R-Audio-L Video 4 2 1 IR Emitters 1 2 3 4 Hi-Z 75 Video 2 1 TPUTS OUTPUTS Control 1 Sig Gnd +V Video In Termination Video In Termination 1A/250V FUSE 115 Sat radio DVD player 5 IR emitter outputs allow IR-3002 flashers to be connected for remote control of source components. When splitting the video signal from a source component, use the dip switch to enable the Hi-Z mode on that input. Power switch Switch for 110-120 or 220-240 operation ear Panel CD player R L 1 SPKR IN Local Global R L 4 SPKR IN Local Global R L 3 SPKR IN Local Global R L 2 SPKR IN Local Global Aria by Channel Vision Model A1260 12 Channel Amplifier Made in China ! ION RIC SHOCK PEN USE CLASS 2 WIRING FOR SPEAKER OUTPUTS ear Panel