Bestop 76303 Installation Instructions Manual

INSTALLATION TIME SKILL LEVEL 1-1/2 Hours 2 - Moderately Easy TOOLS Supertop for Truck Vehicle Application: 7/16" and 9/16" 1/8" Bit • Chevrolet Silverado 1500 / 2500 / 3500 6.5 ' Bed 1999 - 2011 Part Number: 76303 • GMC Sierra 6.5 ' Bed 1999 - 2011 Part Number: 76303 US Patent 6827391

Rev. G 0713 76303 pg. 2 Parts List and Hardware Identifi cation Supertop Fabric Qty - 1 Side Panel, Right Qty - 1 Side Panel, Left Qty - 1 Rear Window Qty - 1 32" Buckle Straps Qty - 2 Elastic Garter Qty - 2 Foam Tape, 14' Qty - 1 Tension Straps Qty - 2 Tailgate Bracket, Right, Part Number 412.08, Qty - 1 Bulb Seal, Part Number 413.03, Qty - 1 1/4" x 1-1/2" Clevis Pin, Part Number 410.95, Qty - 2 1/4-20 Cap Nut, Part Number 198.27, Qty - 12 #8 x 1/2" Self Tapping Screw, Part Number 312.09, Qty - 1 1/4" Flat Washer, Part Number 21.117.10, Qty - 14 Bow Tie Down Assembly, Part Number 194.04, Qty - 2 Clamp, Part Number 411.75, Qty - 4 1/4" Fender Washer, Part Number 410.94, Qty - 4 5/16" Flat Washer, Part Number 117.26, Qty - 4 Tailgate Bracket, Left, Part Number 412.09, Qty - 1 Bow Mount Bracket, Left, Part Number 412.85, Qty - 1 Bow Mount Bracket, Right, Part Number 412.84, Qty - 1 5/16" x 3/4" Clevis Pin, Part Number 410.96, Qty - 2 Hitch Pin Clip, Part Number 409.71, Qty - 4 Rear Belt Rail, Right, Part Number 413.46, Qty - 1 Rear Belt Rail, Left, Part Number 413.47, Qty - 1 Front Bow Half, Part Number 412.96, Qty - 2 Bow Coupler, Part Number 413.00, Qty - 3 Third Brake Light, Part Number 397.52, Qty - 1 Front Belt Rail, Right, Part Number 496.20, Qty - 1 Front Belt Rail, Left, Part Number 496.21, Qty - 1 Rear Bow, Left, Part Number 496.27, Qty - 1 Tailgate Bar, Part Number 496.54, Qty - 1 Rear Bow, Right, Part Number 496.26, Qty - 1 Inner Retainer Bar, Part Number 499.90, Qty - 1 Outer Retainer Bar, Part Number 499.91, Qty - 1 Front Retainer Bar Bracket, Right, Part Number 497.16, Qty - 2

Rev. G 0713 76303 pg. 3 Mount Tailgate Brackets to Rear Belt Rails Assemble Retainer Bar Locate the Bow Mount Brackets in the parts kit. Slide a 5/16" Flat Washer over a 5/16" x 3/4" Clevis Pin. Insert the pin through the rear pivot hole on the Bow Mount Bracket from the outside. Slide a 1/4" Fender Washer over a 1/4" x 1-1/2" Clevis Pin and insert the pin through the front slot of the Bow Mount Bracket from the outside. Repeat this with both Bow Mount Brackets. Assemble Bow Mounts Brackets Locate the Right Front and Rear Belt Rails. Place the ends of the rails against each other. Place the Right Bow Mount Bracket on top of the Belt Rails. Secure the bracket to the rails with four (4) 1/4-20 Cap Nuts 1/4" Flat Washers. Repeat this with the Left Side Bow Mount Bracket and Belt Rails. Assemble Main Bow Mount Brackets and Belt Rails Right Rear Belt Rail Right Tailgate Bracket 1/4-20 Cap Nut Bow Mount Bracket Rear Pivot Hole Front Slot 5/16" Flat Washer 5/16" x 3/4" Clevis Pin 1/4" x 1-1/2" Clevis Pin 1/4" Fender Washer Bow Mount Bracket Rear Belt Rail Front Belt Rail 1/4-20 Cap Nuts Locate the Right Tailgate Bracket and the Right Rear Belt Rail in the parts kit. Place the Right Tail- gate Bracket over the rear stud on the Belt Rail so that the bracket tab points away from the channel on the Belt Rail. Use a 1/4-20 Cap Nut and 1/4" Flat Washer to secure the bracket to the rail. Repeat with the Left Tailgate Bracket and Rear Belt Rail. 1/4" Flat Washer Locate a Front Retainer Bar Bracket and the Right Front Belt Rail. Place the bracket over the front stud which is the one that is 1 1/2" from the front of the rail. Use a 1/4"-20 Cap Nut and 1/4" Flat Washer to secure the bracket to the rail. Repeat with the Left Front Belt Rail. Mount Front Retainer Brackets to Front Belt Rails Right Front Belt Rail Front Retainer Bar Bracket 1/4"-20 Cap Nut 1/4" Flat Washer 1/4" Flat Washers Assemble the two Retainer Bar halves by sliding the inner half into the outer half and align the pre-drilled holes. Install a #8 X 1/2” Self Drilling screw in to the pre-drilled hole.

Rev. G 0713 76303 pg. 4 Install Belt Rail Assemblies Locate the Clamps in the parts kit. Use two clamps to secure each Belt Rail Assembly to the vehicle. Place a Clamp as close to each end of the Belt Rail as possible. Fully tighten the bolt on each Clamp. Repeat this for both Belt Rail Assemblies. Belt Rail Assembly Rear Clamp Slide a Bow Tie Down Strap onto each of the Front Bow Halves. Slide the two halves of the bow into a Bow Coupler. Assemble Front Bow Bow Coupler Front Bow Halves Bow Tie Down Straps Install Foam Tape Lay the Belt Rail Assemblies on top of the truck bed rail with the tab on the Tailgate Bracket toward the center of the vehicle. The front of the rail should be 1-1/4” forward of the rear edge of the front wall of the truck box. Measure the distance between the inside edges of the right and left Belt Rail Assemblies at the front and rear. Place them so that they are 63-1/2" at both places and are centered and square on the bed. Install Belt Rail Assemblies 63-1/2" 63-1/2" Front Edge of Front Wall Measurement between Rails should be 63-1/2" Belt Rail Assembly 1/4" Measure and cut a piece of Foam Tape that will fi t the full length of the bottom of the Belt Rail Assem- bly. Peel the backing off the tape a little at a time and press the tape fi rmly into place on the Belt Rail Assembly. Trim the tape to match the contour of the Tailgate Bracket. Repeat this with both Belt Rail Assemblies. Tailgate Bracket Rear Belt Rail Peel Backing off a little at a time Foam Tape

Rev. G 0713 76303 pg. 5 Place a 1/4" Fender Washer over the 1/4" x 1-1/2" Clevis Pins installed in the Bow Mounts. Slide the legs of the Front Bow Assembly over the Clevis Pins and secure them with 1/4" Flat Washer and a Hitch Pin Clip on each side of the vehicle. Install Front Bow Install Rear Bow Assembly Front Bow Assembly Bow Tie Down Strap 1/4" Fender Washer 1/4" Flat Washer Hitch Pin Clip Rear Bow Assembly 5/16" Flat Washer Hitch Pin Clip Cut Web Strap Reinforcement Place the top fabric on a safe, clean cutting surface. Locate the two (2) wide patches in the seal below the window on the front panel of the top. Use a util- ity knife to cut a slit through all the layers following the indent in the seal. Front Window Cut slit in reinforcement Install Buckle Straps Locate the two (2) 32" Buckle Straps in the parts kit. Thread the end of each strap through the slits from the vinyl (outside) side of the top. Pull the straps through the slits until the back of the buckle is against the slit. Pull Strap Through Locate the two (2) Elastic Garters in the parts kit. Slide a garter over each half of the Rear Bow from the center so that the Garters will hang above the rear window opening. Slide the long tail of a Tension Strap onto each short bow half and the buckle end onto the rear bow half. Adjust the straps so there is about 3" of strap beyond the buckle. Slide the two (2) halves of the Rear Bow into the remaining Bow Couplers. Slide the legs of the Rear Bow Assembly over the 5/16" x 3/4" Clevis Pins and secure them with a 5/16" Flat Washer and a Hitch Pin Clip on each side of the vehicle. Tension Straps Elastic Garters

Rev. G 0713 76303 pg. 6 Thread Buckles on Straps Thread the end of the 32" Buckle Straps through the male half of each buckle. Drape Fabric over Cab Wrap Flaps from front and Snap to Bow Snap Fabric to Front Bow Drape the Supertop Fabric over the roof of the cab with the backing side up and the front window hanging down between the Front Bow and the cab of the vehicle. Locate the two snap fl aps sewn to the inside of the top. Wrap the fl aps around under the bow from the front and snap them to the bow. Strap Buckle Snap Fabric to Rear Bow Carefully drape the fabric over the center and rear bows. Make sure that the sides of the top are smooth between the bows and that the Tension Straps are inside of the outboard snaps on the rear bow. Locate the two rear snap fl aps. Wrap them around under the rear bow from the rear and snap them to the bow. Rear Window Opening Short Bow Rear Bow Wrap Flaps from Rear and Snap to Bow Elastic Garter Elastic Garter Locate Tension Straps inside outboard snaps

Rev. G 0713 76303 pg. 7 Secure the Front of the Top Plastic Strip - Slip into channel in Belt Rail Adjust Bow Position Place the Front Bow on the rear tooth at the front of the Bow Mount Bracket. Front Bow Front Place Bow in rear tooth of Bow Mount Bracket Install Front Retainer Bar Slide the Front Retainer Bar into the sleeve at the bottom of the front deck panel and center it. Com- press the front seal on the deck and push the bar rearward so it is hooked under the Front Retainer Bar Brackets. Front Retainer Bar Front Deck Panel Front Deck Panel Front Retainer Bar Front Retainer Bar Bracket Start at the front corners of the top and work the plastic strip sewn into the bottom of the panels into the channel in the Side Belt Rail.

Rev. G 0713 76303 pg. 8 We recommend that the Third Brake Light sup- plied with this assembly be professionally wired. Locate the plastic clips sewn into the rear corners of the top. Gently pull down on the rear bow and pull down and back on the fabric to hook the clips into the corner of the Tailgate Bracket on the Belt Rail Assembly. Locate the plastic strip next to the clip and hook it into the channel on the Side Belt Rail. Make sure as you do this that the corner clip remains hooked into the corner retainer. Secure the Rear of the Top Use a 0.136" drill bit to drill out the two dimpled holes in the plastic mounting pad on the Third Brake Light. Orient the Third Brake Light so that the pad is horizontal along the Rear Bow and in the center. Peel the backing tape off the bottom of the mounting pad and press it onto the bow. Drill 0.136" Holes Press Light onto center of Rear Bow Install Third Brake Light Tailgate Opening Plastic Strip - Slip into channel in Belt Rail Hook clip into Tailgate Bracket Use the holes in the Third Brake Light mounting pad as a guide to center punch two holes in the Rear Bow. Drill a 0.136" hole at each of these locations. Install a #8 x 1/2" Self Tapping Screw at each of these locations. Unsnap the snap fl aps from the Rear Bow on the driver side of the brake light. Run the wire from the light along the bow and snap the fl aps around the bow and the wire. Wrap the wire around the bow down to the pickup bed rail. Drill 0.136" Hole and install #8 x 1/2" Self Tapping Screws Thread Wire through Snap Flap Secure Third Brake Light to Rear Bow

Rev. G 0713 76303 pg. 9 Orient the Rear Window with the plastic J-Hook toward the top. Align the J-Hook on the top of the window with the J-Hook sewn into the top above the rear window opening. Slide them together until the Rear Window is centered in the opening. Engage the zippers on each side of the window, but do not close them yet. J-Hook Rear Window Inside of Top Engage J-Hook on Rear Window Close Zippers Install Tailgate Bar on Rear Window Slide Rear Retainer Bar onto Rear Window Locate the Tailgate Bar and the Bulb Seal in the parts kit. Slide the channel in the Bulb Seal over the ledge on the Tailgate Bar. Install Bulb Seal on Tailgate Bar Slide the Tailgate Bar onto the tube strip sewn to the inside of the Rear Window and snap the center of the window to the bar. Place the Tailgate Bar in the Tailgate Brackets on the Belt Rail Assemblies. Close the zippers on each side of the window. Close the fl aps on each side of the window over the zippers and fasten the snaps. Check that the tailgate closes on the Bulb Seal. Fasten Snap

Rev. G 0713 76303 pg. 10 Orient the Side Panels with the plastic J-Hook toward the top and the zipper with the fl ap over it toward the rear and determine which is for the driver’s side of the vehicle and which is for the pas- senger side. Align the J-Hook on the top of the panel with the J-Hook sewn into the top above the panel open- ing. Slide them together. The J-Hook in the top is in three pieces, so make sure that the J-Hook on the Side Panel stays engaged through the splits. Engage the front and rear zippers on the panel and close them. Work the plastic strip sewn into the bottom of the Side Panel into the channel in the Belt Rail Assembly. Fasten the Loop on the top of the Side Panel to the Hook on the deck above the opening. Repeat this procedure for the other Side Panel. Zipper Flap toward Rear Tailgate Opening J-Hook J-Hook Install Side Panels Side Rail Plastic Strip - Slip into Channel Quarter Panel Adjust Tension on Top Slide Front Bow forward to increase tension Rolling the Rear Window Roll Rear Window Elastic Garters Use the Elastic Garters on the Rear Bow to secure the Rear Window in the open position. Unzip the side zippers on the Rear Window, release the tail- gate bar snap, and slide out the Tailgate Bar. Roll the window from the bottom to the top and wrap an Elastic Garter around each end of the window. It may be necessary to increase the tension on the top for a better fi t. In this case, move the Front Bow forward to the next tooth in the Bow Mount Bracket. Adjust the Tension Straps on the Rear Bow as nec- essary for the best fi t.

Rev. G 0713 76303 pg. 11 Collapsing the Pickup Top Remove the Side Panels and the Rear Window and store them carefully. Remove Windows Move the Front Bow out of the teeth in the Bow Mount Bracket and allow the bow to collapse onto the front of the truck bed. Fold the glass under and toward the front of the bed. Pull the 32" Buckle Strap about halfway outside the top. Release the Front Bow Release Fabric Release the Rear and Center Bows Rotate the Rear Bow forward to collapse the Rear and Center Bows onto the Front Bow. As you are collapsing the bow assembly, make sure that the J-Hook above the side opening is folded inside the vehicle. Fold all the J-Hook and fabric in toward the center along the front of the bed on each side. Slide Front Bow out of teeth Collapse Front Bow Fold Fabric in as bows collapse Release the fabric from the channel in the Belt Rails and release the rear corner clips from the Tailgate Brackets.

Rev. G 0713 76303 pg. 12 Wrap the Buckle Straps around the fabric and the J-Hook and secure the buckles. Make sure that all the fabric is caught in the straps to keep it from fl apping. Secure Fabric with Buckle Straps Secure the Bows Use the Tie-Down Straps on the Front Bow to secure the bow assemblies to the Belt Rail. Wrap the straps around the bows and hook the plastic strip on the end of the strap into the channel in the Side Belt Rail. If you wish to remove the bows completely, remove the cotter pins that secure the bows to the Bow Mount Brackets. Lift the bows off the vehicle, keeping the bows together. Carefully store the bows and fabric. Replace the Cotter Pins in the Bow Mount Brackets on the vehicle. To Remove the Bow Stack Remove Cotter Pins to Remove Bows - Then Replace Pins Wrap Tie-Down Strap around Bows Hook Plastic into Channel in Belt Rail

Rev. G 0713 76303 pg. 13 For further information or request for warranty work, please contact: Bestop Inc. Customer Service (800) 845-3567 (303) 465-1755 Damaged Slider - Jaws Spread Apart (sometimes broken) Normal Slider - Jaws Parallel Care and Maintenance of your Bestop Product Your Bestop product is made of the fi nest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush Rinse with clear water to remove all traces of soap. Bestop recommends using Bestop Cleaner (part no. 11201-00) and Bestop Protectant (part no. 11202-00) Bestop Cleaner and Bestop protectant are specially formulated to provide a total cleaning and protection system. Bestop Cleaner safely removes the toughest stains, will not harm vehicle fi nishes, is biodegradable and environmentally friendly. Bestop Protectant protects against UV- fading, cracking and hardening, and repels dust, grease, dirt and mildew. Windows: Keep windows clean to avoid scratching. DO NOT use a brush on the windows! Wash with a water-soaked cloth or sponge and a mild dishwashing detergent. Bestop recommends Bestop Vinyl Window Cleaner (part no. 11203-00), which safely cleans and protects vinyl windows and helps prevent UV damage. NEVER WIPE THE WINDOWS WHEN THEY ARE DRY. Be careful when cleaning snow or frost from the vinyl windows since they are easily scratched and may crack at low temperatures. DO NOT roll the sides or rear window in cold weather. The windows become stiff and will crack. Cracks caused by misuse in cold temperatures are not covered under warranty. Zippers: Keeping zippers cleaned and lubricated with Bestop’s Zipper Cleaner (part no. 11206-00) will help prevent damage and keep the zippers in smooth working condition. If a zipper opens behind the slider, the slider may have been spread apart. This problem can usually be repaired by using an ordinary pair of pliers to bring the sides back into parallel. Return slider to the end of the zipper in the normal Open position. Squeeze lightly at fi rst and test the zipper. If the zipper continues to remain open squeeze more fi rmly with the pliers and try the zipper again. Repeat this procedure until the zipper operates correctly. Water: Seeping through at the seams may be stopped by applying 3-M Scotchgard® on the inside of the seams. Rips in the fabric may be repaired with Bondex® iron on patches. Iron the patches to the Inside of the top, carefully following the Bondex® instructions. Snaps: Keep snaps cleaned and lubricated with silicone to help prevent snaps from sticking to the studs. If a snap does become stuck to a stud, use a screwdriver and GENTLY pry apart to prevent permanent damage to the snap or the top fabric. LIMITED WARRANTY We warrant our product to be free from defects in material and workmanship, for the terms specifi ed below, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair or replacement of any item or items found by the factory to be defective within the time period specifi ed. If you have a warranty claim, fi rst you must call our factory at the number below for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, fi re, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is not covered under this warranty. THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR REPLACE-A-TOP™, SAILCLOTH REPLACE-A-TOP™, SUPERTOP®, SUPERTOP® REPLACEMENT SKINS, SUNRIDER®, AND TIGERTOP®: TWO YEARS FROM DATE OF PURCHASE. THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER “SOFT GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY VINYLS, PLASTICS, AND/OR FOAM): ONE YEAR FROM DATE OF PURCHASE. THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER “HARD GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY METALS, PLASTICS, AND/OR FIBERGLASS): ONE YEAR FROM DATE OF PURCHASE. ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.