ETC ColorSource PAR Installation Manual

ColorSource® PAR v1.5 Corporate Headquarters  Middleton, Wisconsin, USA  Tel +608 831 4116 Service (Americas)  [email protected] London, UK  Tel +44 (0)20 8896 1000  Service: (UK) [email protected] Rome, IT  Tel +39 (06) 32 111 683 Service: (UK) [email protected] Holzkirchen, DE  Tel +49 (80 24) 47 00-0  Service: (DE) [email protected] Hong Kong  Tel +852 2799 1220  Service: (Asia) [email protected] Web: etcconnect.com  © 2017 Electronic Theatre Controls, Inc.  Product information and specifications subject to change.  ETC intends this document to be provided in its entirety. 7412M2100-1.5  Rev A  Released 2017-01 Overview The ColorSource PAR is an affordable LED wash fixture that uses the RGB-L (red, green, blue, and lime) color system to provide a rich, bright light. This fixture is available in both original and Deep Blue variants. The Deep Blue uses an array that offers richer, more saturated blues and stronger magentas in exchange for the more jewel-toned blues like sky or turquoise. For more information, see the ETC website at etcconnect.com. CAUTION: • Risk of eye injury. Do not stare directly into the light. • Do not operate in proximity to flammable materials. Note: Features described in this document require the latest version of software. For information on updating fixture software, see Updating the fixture software on page 9. 9.9" 251mm 8.2" 209mm 7.8" 199mm 9.5" 241mm 4.8" 121.8mm 4.3" 110mm 4.0" 102.5mm 8.2" 207.7mm 12.2" 309.8mm 16.6" 422.8mm 14.3" 362.2mm 10.4" 265mm 18.7" 475.2mm 6.1" 154.9mm

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 2 of 12 ETC Environment The ColorSource PAR operates in ambient temperatures of 0°C–40°C and it comes with a variable-speed fan. Electrical • Operates between 100V and 240VAC at a frequency of 50/60Hz. • Maximum power consumption is 120W. • Up to 9 luminaires (15A max) may be linked via power thru connector (10 luminaires total per circuit) when used with an R20 relay module or Unison Echo® Relay Panel. Consult breaker trip curves when used with other equipment. Requires power from a non-dimmable source. Typical power consumption Note: The ColorSource PAR is for indoor use only. Note: • Maximum recommended ambient operating temperature: Ta = 40°C (104°F) • Maximum anticipated external surface temperature at 40°C ambient: Tmax = 80°C (176°F) • External temperatures after 5 minutes of full- brightness operation at 25°C (77°F) ambient: 30°C (86°F) • External temperature (steady state achieved) at 25°C (77°F): 41°C (106°F) WARNING: Disconnect the fixture from power and DMX and allow it to cool before performing any cleaning and maintenance. 100V 120V 230V Idle Power/Current 1.22W/0.026A 1.21W/0.026A 1.14W/0.026A Direct at Full/Current 107W/1.07A 106W/0.88A 104W/0.46A

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 3 of 12 ETC Installation Mounting The ColorSource PAR ships with a standard yoke. An expandable floor stand yoke is available as an optional accessory. Contact your local dealer for more information. Safety cable The safety cable (or other approved safety device) must be attached to the fixture. Attachment loops are provided on the fixture housing. Take care to leave as little slack as possible in the safety cable to avoid catching the yoke of the fixture. Connectors • Power: Two powerCON® connectors for power in and thru • Data (DMX512/RDM): Two five-pin XLR connectors OR two RJ45 connectors for data in and thru Conversion cables are available from ETC. Please contact your ETC customer service representative and request part number W6538 for RJ45 to female XLR, and part number W6539 for RJ45 to male XLR. Note: This fixture is not Ethernet/data network compatible. Safety cable attachment loop Rear view of PAR with RJ45 DMX connectors Rear view of PAR with XLR connectors

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 4 of 12 ETC Setting up the fixture 1: Plug power cord into the powerCON In connector on the rear of the fixture. 2: Make any power-thru cable connections prior to applying a power source. 3: Plug power cord into power source. Powering up 1: Press the Mode button once to wake the display. The display shows the DMX address. 2: Press the Mode button a second time to access the Presets/Sequences menu. Adjusting the tilt The fixture can be tilted up and down and rotated (panned) as needed. 1: Loosen, but do not remove the yoke locking knob. 2: Tilt the fixture to the desired angle. 3: Tighten the yoke locking knob. User interface The user interface allows you to set the start address of the fixture, access the stand-alone presets and sequences, and set the DMX control mode. • The DMX address will blink when no DMX is present and a preset or sequence is not active. The inactivity time-out is disabled while in a data loss state. • After 5 seconds of inactivity when DMX is present, the display goes dark. Note: The ColorSource PAR is not self terminating. You must terminate the last fixture in line with a 120 ohm resistor. XLR terminators are not available from ETC. To purchase an RJ45 terminator, please contact your ETC customer service representative and request part number N4086.

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 5 of 12 ETC Mode button Pressing the Mode button activates the Preset/Sequence menu; the last active preset or sequence plays automatically. Pressing the Mode button a second time deactivates the selected preset or sequence. The display will revert to show the DMX start address. • If DMX data is present, the current preset or sequence plays in the background and DMX data continues to take priority. • If DMX data is lost and a preset is active in the background, the last selected preset or sequence automatically plays. Setting the DMX address 1: Press the Mode button until the DMX address is displayed. 2: Use the Up and Down buttons to select the DMX address for the fixture. Up Power in Data in (XLR version shown) Down Data thru (XLR version shown) Power thru User interface Mode button DMX address Presets and Sequences Scroll through presets  followed by sequences 

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 6 of 12 ETC Setting presets and sequences There are twelve factory-configured presets followed by five factory- configured sequences built into the fixture. From the Preset/Sequence menu, press the Up and Down buttons to scroll through the list. The sequence or preset plays immediately upon selection. All presets and sequences can be re- recorded through an RDM device. Re-recording a preset 1: Using DMX or RDM, set the desired RGB levels. 2: Press the Mode button to access the Preset/Sequence menu. 3: Using the Up and Down buttons, navigate to the preset number that you want to re-record. 4: Hold the Mode button for 3 seconds to confirm the preset selection. The user interface will show a 3-second countdown. The preset number blinks once to confirm that the preset has been recorded. It is possible to activate a known preset or sequence from a connected fixture when DMX is not present. If a connected fixture activates a preset or sequence that is not recognized by the PAR, the PAR will hold its last look. When DMX is restored, the DMX takes priority. Note: When the fixture is in Direct mode () or 1-channel mode (), you cannot re-record presets. When you re-record presets with the fixture in RGB mode (), the intensity is set to full and the strobe is turned off. See Changing the DMX control mode on page 8.

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 7 of 12 ETC Pre-configured presets Pre-configured sequences Adjusting the intensity of presets 1: Ensure that DMX data is not present. 2: Press the Mode button to access the Preset/Sequence menu, and then press the Up and Down buttons to select the preset that you want to edit. 3: Hold the Mode button for 3 seconds. The display shows : ## where the number is an intensity level from , or . 4: Press the Up and Down buttons to change the intensity level of the preset in real time. 5: Press the Mode button to confirm your selection and return to the Preset/Sequence menu. The fixture will automatically return to the Preset/Sequence menu after 10 seconds of inactivity without saving edits to the preset intensity. This cancels unsaved changes. Preset Name Preset Name 1 3200K White 7 Magenta 2 5600K White 8 Yellow 3 Red 9 Orange 4 Green 10 Light Yellow 5 Blue 11 Light Blue 6 Cyan 12 Light Pink Sequence Name 1 Rainbow Fast 2 Rainbow Slow 3 Warm Colors Fast 4 Cool Colors Fast 5 Random

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 8 of 12 ETC Changing the DMX control mode You can set the DMX control mode for the fixture to one of four available mode options. 1: Press the Mode button until the DMX address is displayed. 2: Hold the Mode button for 3 seconds. The display shows the current DMX control mode. 3: Press the Up and Down buttons to change the DMX control mode. • : 5-channel mode (intensity, red, green, blue, and strobe) • : Direct emitter control (intensity, red, green, blue, lime, and strobe) • : Single-channel mode controls the intensity of preset 1 (defaults to 3200K White) • : RGB mode (red, green, and blue) 4: Press the Mode button to confirm your selection. The fixture will automatically return to the DMX address after 10 seconds of inactivity without saving edits to the DMX control mode. This cancels unsaved changes. DMX control channels *Original ColorSource PAR v1.5 fixture uses blue in channel 4; Deep Blue ColorSource PAR v1.5 fixture uses indigo in channel 4. DMX Channel  (5 Channel)  (Direct)  (1 Channel)  (RGB) 1 Intensity Intensity Intensity Red 2 Red Red Green 3 Green Green Blue 4 Blue Blue/Indigo* 5 Strobe Lime 6 Strobe

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 9 of 12 ETC Locking the user interface After you have set up the fixture, you can lock the user interface to prevent additional changes. 1: Hold the Up and Down buttons simultaneously for 3 seconds. The display will show  to indicate that the user interface is locked. 2: To unlock the user interface, hold the Up and Down buttons simultaneously for 3 seconds. Updating the fixture software ETC recommends using UpdaterAtor software to manage software updates. For more information on UpdaterAtor, see the UpdaterAtor Software Quick Guide, which you can download for free from etcconnect.com. When you add a ColorSource fixture running a newer software version or update a ColorSource fixture to a newer software version using UpdaterAtor, you can use that fixture to push the newer software version to all connected ColorSource fixtures. You can push newer software versions from a connected fixture only on ColorSource fixtures running software v1.3.0 or newer. Use UpdaterAtor to update individual fixtures running versions older than v1.3.0. 1: Remove power and DMX from the master fixture that is running the software version that you want to push to other fixtures. 2: Hold the Up and Down buttons simultaneously while restoring power. 3: The display will show  to indicate the update mode is selected. 4: Press the Mode button to start the update process. • The display will alternate between  and the percentage complete while updating. • The master fixture will reboot once the update is complete. Restoring factory defaults Hold all three buttons (Mode, Up, and Down) simultaneously for 5 seconds. The DMX start address will blink once to confirm that defaults have been restored.

ColorSource PAR v1.5 ColorSource PAR v1.5 Page 10 of 12 ETC Error codes There are three error codes that may be shown on the user interface. • : Screen toggles between and to indicate a problem with the color calibration. The fixture will need to be returned to the ETC factory; contact your local dealer to set up a repair. • : Screen toggles between and to indicate that the fixture has gone into over-temperature protection mode to avoid damaging the fixture. Once the fixture has self-cooled, the error will automatically clear. • : Screen toggles between and to indicate that the upgraded fixtures have a software issue. Reload software to clear the error. If the error persists, contact ETC. RDM values Parameter Value Description Manufacturer ID 0x6574 Electronic Theatre Controls Model ID 0x0201 ETC ColorSource PAR 0x0202 ETC ColorSource PAR Deep Blue Personality ID 1 5 Channel 2 Direct 3 1 Channel 4 RGB