Falcon PHASER2 Manual 

WORLD CLASS SECURITY FALCON PHASER2 Advanced Keyless Entry System NATIONWIDE INSTALLATION SERVICE 0800 622 474 HELPLINE: 0906 700 10 20 (All calls charged at 50p/min) Internet: http://www.falcon-security.com Email: [email protected]

Car finder Total closure Remote boot release Code learning (up to 4 remotes) Flashes hazard lights Universal Central Locking Siren/horn output 2. Button Function Table button door lock door unlock ignition on button #1 once lock lock lock button #1 2 sec. car finder car finder button #2 once unlock unlock unlock button #3 2 sec. boot release boot release 2.04 Button definition 3. Code Learning The remotes have programmed to the system when leaving the factory. If necessary there are 2 methods to program a new remote to the system as follows: - Power on the system - Lights flash twice - Within 10 sec., press the onboard switch 6 times - The system enters into the code learning mode and the indicator lights turn on to confirm - Within 10 sec., press any button of 1st remote

programmed to the system - Follow the same procedure as above to program the 2nd, 3rd and 4th remote. You have up to 10 sec. for the learning of each remote The system will quit the learning mode as follows and the indicator lights will turn off to confirm: *Upon programming 4 remotes to the system *If doing nothing for 10 sec. The 2nd method of programming the new remote to the system: - Unlock the door by remote control - Within 20 sec. turn the ignition on-off 5 times then back to on - The system enters into code learning mode and the indicator lights will turn on to confirm - Within 10 sec. press any button of 1st remote - Lights will flash once and then stay on again to confirm the 1st remote is programmed to the system - Follow the same procedure as above to program 2nd, 3rd and 4th remote. You have up to 10 sec. for the learning of each remote. - The system will quit the learning mode as follows and the indicator lights will be off to confirm: * Turn the ignition off during the code learning * Upon programming 4 remotes to the system * If doing nothing for 10 sec. 4. System Operation & Installation 4.01 Door lock - Press the lock button once with the ignition off - Doors lock - Lights flash once - The siren/horn chirps once (if connected) - Then window closure output will be on for 40 sec. * If pressing the lock button with ignition on then the window closure output won’t be activated

- Press the unlock button once - Doors unlock - Lights flash twice - The siren/horn chirps twice (if connected) 4.03 Boot release - Press the boot release button (#) for 2 sec. will operate the boot release output. 4.04 Car finder - Press the lock button for 2 sec. the horn/siren will chirp once (if fitted) and the lights will flash 12 times to help you locate the car. 4.05 Programming lock and unlock time - 1 sec. pulse -> put the onboard jumper on - 4 sec. pulse -> remove the onboard jumper

- C1-1 and C1-3 White -> Lights flash outputs[+] Connect C1-1 and C1-3 to indicator lights. - C1-2 White/Red -> Polarity input for C1-1 & C1-3[+ or -] Connect C1-2 to positive or negative depending on the polarity of the cars indicator wires.

Connect the red (+) wire of an optional siren for confirmation chirps. An additional relay will be required when connecting this output to the car horn instead of a siren; see the wiring below: - C1-7 Yellow <- Ignition input [+] Connect to an ignition wire that shows +12V when the key is in both [on] and [start] positions - C1-8 Gray/Black -> Window closure output [-500mA] Can be connected to a window closure module or for cars with total closure/comfort closure to the cars total closure wire where applicable (max 500mA). If the car does not have a separate total closure wire a relay will be required. - C1-9 Gray -> Boot release output[-500mA] An additional relay will be required when wiring, see the wiring below: