Intek Elite 16D Installation & Programming Manual

To exit program modes when you have finished programming: Press - Program light goes out The panel is now back in Run Mode, any program changes you have made will have replaced previous values and be in effect. Note: During programming Tampers and 24 hour alarms are disabled which allows quiet access to the panel, detectors and satellite siren units etc. On exiting program mode, all inputs are scanned and if any tampers or 24Hr alarms are present an activation will occur. USER CODES - (P1E to P24E) & (P99E) There are 25 codes available in the Elite, 24 user codes and 1 install code. The user codes are located in addresses 1-24. As default, Code 1 has Master Code permissions and must be used to enter program mode. The Installer code is stored at address 99 and is used to move from Client Program mode up to Installer Program mode. Codes 1-24 may be varied in length from 1 to 6 digits.Code 99 must be 3-6 digits. To program a User Code you must first be in client or installer program mode, then select the address from 1-24. (If there is already a code programmed at this address, it will be flashed back to you) Now enter the code then press the ENTER key. eg. P 1 E 1234 E 3 beeps - program light flashing In this example we have set Code 1 ( Master Code ) to be 1234. eg. P 5 E 567 E 3 beeps - program light flashing In this example we have set code 5 to be 567 To replace a code simply enter the new code in the same address as the old code. This will overwrite the previous code but maintain the user permissions as mapped to that user number. To clear or delete a code simply enter the EXCLUDE button at the address where the old code is stored. eg. P 3 E E 3 beeps - Program light flashing When flashing back codes and values Zone indicators 1-8 are used to indicate digits 1-8. The digit 0 is indicated by the "A" light and 9 is indicated by the "B" light. Note: Where there are multiple options at one address, options 0 & 9 have been reserved. Entering a 0 at

Option 0 - Turns all options off Option 1 - Code has Area A permissions Option 2 - Code has Area B permissions Option 3 - Code has Area C permissions Option 4 - Code can Arm Area Option 5 - Code can Disarm Area Option 6 - Code can turn Monitor on Option 7 - Code can turn Monitor off Option 8 - Code can Operate control Functions Option 9 - Turns all options on. NOTE: Options 4, 5, 6 & 7 are used in conjunction with options 1, 2 & 3 whereby options 4, 5, 6 & 7 determine the functions and options 1, 2 & 3 determine the area of operation. USER CODE PERMISSIONS (Code Options) 2nd Set - P49E-P72E Option 0 - Turns all options off Option 1 - Code can override DOTL timer Option 2 - Code can change dialler telephone numbers Option 3 - Code can alter the real time clock Option 4 - User can start a print dump of the event buffer Option 5 - .User can answer an incoming call and start up/down load Option 6 - User can enter Client Program and change their code only. Option 7 - User can enter Client Program and change all codes. Option 8 - User can enter Client Program mode and then Installer Program mode(if installer code is known). Option 9 - Turns all options on. USER CODE TIME ZONES - P73E-P96E Users codes may have Time Zones or windows assigned to control their operation. These Time Zones determine when a particular user code will work. Addresses P73E - P96E are used to map the user code to the required Time Zones. The actual Time Zone parameters are defined at addresses P681E - P704E. A single value from 0-8 must be assigned to each user code. Time Zone zero (0) is fixed as 24 hour seven day access and is the default time zone for all 24 user codes. P73E TZ E Where TZ represents the Time Zone from 0-8 valid for User Code #1 (Fixed as TZ-0) P74E TZ E Where TZ represents the Time Zone from 0-8 valid for User Code #2 P96E TZ E Where TZ represents the Time Zone from 0-8 valid for User Code #24 NOTE: More than one Time Zone may be assigned to each user allowing different time based controls for different days of the week etc. INSTALLER CODE - P99E This code is used to enter full Installer Program mode (Program light flashing) from Client Program mode (Program light steady) The default installer code is 000000. To change this code enter your new installer code at the P99E address. The new code will be flashed back to you automatically. Like User codes, the Program code may vary from 3-6 digits in length P100E Option 8 If this option is on (Led 8 on) then the installer code can access installer mode directly without needing to enter via client program mode.(All areas must be unset and not in monitor mode).

This block of addresses (P101E - P108E) are used to map output modifiers to each of the 8 outputs available on the Elite. Note: Only 5 outputs are available on the Elite mother board. The additional outputs are available on the Output Expander module. P101E 1E Invert output #1 - Default off 2E Flash output #1 - Default off 3E Single pulse to output #1 - Default off 4E Lockout output #1 once reset - Default off 5E Output mapped to Remote Command Control - Default off 6E Output mapped to local Command Control - Default off 7E Day zones linked to pulse timer - Default off 8E Spare Option 1 Invert Output - This option is used to invert the normal state of the output. The Elite uses open collector type transistor switches and the default state of all outputs is off or high. When in alarm the transistor switch is turned on and the output is switched low. The invert option reverses this function. Option 2 Flash Output - This option causes the output to switch on and off at 2 second intervals when in alarm and is normally used to flash a lamp during an activation. Option 3 Single Pulse to Output - This option, when applied, produces a single 1 second pulse at the output during an alarm (the pulse time is the value programmed at the output pulse timer address). Option 4 Lockout Once Reset - This option is used to limit the output to one operation per arming period. Option 5 Output mapped to Remote Command Control - This option is used to map an output to the remote command control function whereby the output can be controlled via the telephone (this requires the optional speech board unit) Option 6 Output mapped to Local Command Control - This option is used to map an output to the local command control feature whereby the output can be controlled directly from the keypad. Option 7 Day Zones Linked to Pulse Timer - Day Zones programmed to this output will pulse at the pulse timer rate (P441E) for the duration of the day zone to keypad timer (e.g. if the day zone is in partition A, then the timer at P457E applies) Option 8 Spare P102E - P108E As per P101E above for Outputs 2-8 OUTPUT OPTIONS SECOND SET - P111E - P118E In this block of addresses P111E relates to output #1, P112E relates to output #2 etc

2E Keypad Tampers to Output #1 3E Zone Tampers to Output #1 4E Cabinet Tamper to Output #1 5E Radio Panic to Output #1 6E Mains Fail to Output #1 7E Battery Low to Output #1 8E Phone Line Fail Option 1 Keypad Panic to Output - This option is used to map the operation of the keypad panic button to an output i.e. when the Panic button on a keypad is pressed any output with this option enabled will turn on. Option 2 Keypad Tampers to Output - This option is used to map Keypad Tampers to an output. Keypad Tampers are generated when an invalid code is entered four times. Option 3 Zone Tampers to Output - Where dual end-of-line resistors are being used to provide individual zone tampers Option 3 at this address is used to map the Zone Tampers to an output. Option 4 Cabinet Tamper to Output - This option is used to map activations of the common Tamper Input to an output. This common tamper input is normally used to monitor the panel cabinet and satellite tamper switches. Option 5 Radio Panic to Output - This option will map the operation of a Radio pendant panic button to an output. Programming of Radio Pendant options is found at P581E - P596E Option 6 Mails Fail To Output - A mains failure will be indicated at this output when option 6 is enabled at this address. The Alarm Reset Timer MUST NOT be used in conjunction wit this option. Option 7 Low Battery - A battery Low condition will be indicated at this output when option 7 is enabled at this address. The alarm reset timer MUST NOT be used in conjunction with this option. Option 8 - Phone Line Fail- A telephone line failure will be indicated at this output when option 8 is enabled at this address. When the line restores this output will return to normal.

This block of addresses are used to map automatic turn on and turn off periods to each of the outputs where required. The start of the time zone will cause outputs mapped at these addresses to turn on whereas the end of the time zone will cause the output to turn off. As with User Code time zones, the actual times assigned to each time zone(1-8) are defined at addresses P801E - P824E. Multiple Time Zones may be assigned to each output P121E TZE Where TZ represents the Time Zone # which defines the turn on and turn off times required for output #1 P122E TZE Where TZ represents the time zone # which defines the turn on and turn off times required for output #2 P123E TZE Where TZ represents the Time Zone # which defines the turn on and turn off times required for output #3 P124E - P128E As per above but for outputs 4-8 NOTE: A value of zero (0) at these addresses will disable any auto turn on turn off features at that output. OUTPUT ENABLE TIME ZONES - P131E - P138E This block of addresses are used to map enable time zones to each of the outputs as required. The assigned time zone will enable the output to be activated. As with User Code time zones, the actual times assigned to each time zone(1-8) are defined at addresses P801E - P824E. This feature is normally used to restrict the Access Control functions to pre-determined times and days P131E TZE Where TZ represents the time zone which enables output #1 P132E TZE Where TZ represents the time zone which enables output #2 P133E TZE Where TZ represents the time zone which enables output #3 P134E - P138E As per above but for outputs 4-8 NOTE: A value of zero (0) at these addresses will enable that output 24hrs 7 days. KEYPAD OPTIONS - P140E - P158E All keypads must be assigned to a partition or area. Keypads may be assigned in more that one area whereby the area setting and unsetting is determined by the user code permissions. If a keypad is assigned to one area only, activity in another area will not be shown. (with the exception of zone indications). NOTE: A keypad can only be used to control the partition or area to which it has been assigned. Within the display of the Elite V4 keypads you will find an "ARMED" indicator as well as area "A" and area "B" indicators. When a keypad is assigned to only one area, the "ARMED" indicator will show steady on for armed, flashing on and off for monitor and steady off for disarmed. If a keypad is assigned to multiple areas the area "A" and "B" indicators will show steady for area armed, flash on and off for area in monitor and remain off for area disarmed. Area "C" is indicated by the "ARMED" light in the same way as the "A" and "B" NOTE: In a partitioned system areas A, B & C can be set, unset and monitored independently

system. Each of the address lines from P140E to P158E may have 8 options assigned where the 8 options represent the individual addresses of the keypads in the system. i.e. if options 1, 2 & 4 are enabled at address P140E then keypads 1, 2 and 4 would be assigned to area "A". P140E 1-8E Keypads assigned to Area A (Default 1-8) P141E 1-8E Keypads assigned to Area B (Default none) P142E 1-8E Keypads assigned to Area C (Default none) P143E 1-8E Keypads with permission to Set (Default 1-8) P144E 1-8E Keypads with permission to Monitor (Default 1-8) P145E 1-8E Keypads with permission to use the Control Function (Default 1-8) P146E 1-8E Keypads with permission to Exclude (Default 1-8) P147E 1-8E Keypads with permission to Line Monitor (Default 1-8) P148E 1-8E Keypads with permission to program User Codes (Default 1-8) P149E 1-8E Keypads with permission to Installer Program Mode (Default 1-8) P152E 1-8E Keypads with facility to turn the LED's off after Exit Delay (Default none) P153E 1-8E Keypads with buzzer mapped to keypad tampers (Default 1-8) P154E 1-8E Keypads with buzzer mapped to zone tampers (Default 1-8) P155E 1-8E Keypads with buzzer mapped to system tampers (Default 1-8) P156E 1-8E Keypads with Panic button enabled (Default 1-8) P157E 1-8E Keypads with buzzer mapped to keypad panic activation (Default 1-8) P158E 1-8E Keypads with buzzer mapped to phone line failure (Default none) At address lines such as P140E where there are 8 bits or options available, each option can be selected by pressing the numeric key which corresponds to the option or bit number your wish to enable. For example, to assign keypads 1,2, & 4 to Area "B" P 141 E 124 E LED's 1,2 & 4 come on 3 beeps, program light flashing When you enter the program address, i.e. P140E, any existing options will be displayed to you. As you enter your options, the display will be updated to show the current option status. NOTE: If an option is already enabled pressing the numeric key which corresponds to that option will toggle the option off. Note: Where there are multiple options at one address, options 0 & 9 have been reserved Entering a 0 at

Zone will cause Area "A" to arm, disarm or both, based on the programmed options set at P180E. PARTITION "A" PRIMARY OUTPUT OPTIONS first set - P171E - P178E This block of addresses sets a number of output options which are specific and unique to the operation of partition or Area "A". Activity in Areas "B" or "C" will have NO direct effect on the options set at these addresses. P171E 1E Normal zone alarms to output #1 2E 24 hour alarms to output #1 3E Monitor Mode alarms to output #1 4E Pendant chirps to output #1 5E All zones sealed indication to output #1 6E 2 second pulse on arming or disarming to output #1 7E Intelligent smoke reset pulse to output #1 8E Day zone alarms to output #1 Option 1 Normal zone alarms to output #1 - This option will map activation from normal zone alarms from Area "A" to output #1. Normal zones are those which will only activate when the partition is armed (Set) Option 2 24 Hour alarms to output #1 - This option will map activations from zones defined as Area "A" 24 Hour to output #1. Zones are defined as 24 Hour at P338E and P358E Option 3 Monitor Mode alarms to output #1 - This option will map activations from zones defined as Area "A" Monitor Mode to output #1. Zones are defined as Monitor Mode at P339E and P359E Option 4 Pendant Chirps to output #1 - This option will map two short pulses (Chirps) to output #1 when Area "A" is set via a radio key (Pendant) and four short pulses to output #1 when Area "A" is unset again. Option 5 All zones sealed indication to output #1 - This option will map a Area "A" safe indication to output #1. A safe indication is produced when all zones in an area are sealed, i.e. zone lights off. Option 6 2 second pulse to output #1 on arming or disarming - This option will map a 2 second pulsed output at Output #1 each time Area"A" is armed or disarmed as defined at P199E options 6&7. Option 7 Intelligent Smoke Reset pulse to output #1 - This option is similar to option 6 in that it produces a momentary pulse at the output when Area "A" is armed and is used to reset latching smoke detectors. The difference is that this option will only produce a pulsed output if a 24 Hour zone in Area "A" has been activated during the previous armed period. Option 8 Day zone alarms to output #1 - The option will map activations from Area "A" zones defined as Day Zones to output #1. Zones are defined as Day Zones at P340E and P360E. Day zones are those which operate only during periods when the Area is disarmed and are normally used as door bells and shop minders etc. Note: P172E through P178E are as above but applied to outputs 2-8 Option 7 MUST be used on systems where ESL brand 449 series smoke detectors are installed rather than option 6. This is due to the way in which the 449 series detectors perform a "self check" function every 24 hours. Interrupting the power supply to these detectors restarts their internal timer and in normal system

As with P171E to P178E, this block of addresses sets a number of output options which are specific and unique to the operation of partition or Area "A". Activity in Areas "B" or "C" will have NO direct effect on the options set at these addresses. P181E 1E Any exclude to output #1 2E Auto-Exclude warning to output #1 3E Entry beeps to output #1 4E Exit beeps to output #1 5E Control function to output #1 6E Set/Unset indication to output #1 7E Monitor Mode on/off to output #1 8E Keypad Duress to output #1 Option 1 Any exclude to output #1 - This option will produce a change of state at output #1 if there are any zones excluded, either manually or automatically. This change of state will occur at the end of the Exit delay. The output reset time (P421E) should be set to zero when this option is enabled. Option 2 Auto-Exclude warning to output #1 - This option will produce a 2 second pulse at output #1 at the end of the exit period if a zone has been Auto-excluded in Area "A". An Auto-Exclude occurs when a zone is left un-sealed at the end of the exit delay. At the end of the exit delay zones not defined as Auto-Exclude which are left un-sealed will produce an activation. Auto-Exclude assignments are found at P342E and P362E Option 3 Entry beeps to output #1 - This option will map the keypad entry beeps to output #1. Option 4 Exit beeps to output #1 - This option will map the keypad exit beeps to output #1. Option 5 Control function to output #1 - This option maps the control functions in Area "A" to output #1. Control function parameters for Area "A" are defined at P198E options 5-8 Option 6 Set / Unset indication to output #1 - This option will turn output #1 on when Area "A" is armed and turn output #1 off when Area "A" is disarmed. This change of state occurs at the start of the exit delay and when the Area is disarmed. Output reset time should be set to zero (P421E0E) Option 7 Monitor Mode on / off - This option will turn output #1 on when Area "A" is placed in Monitor Mode and turn output #1 off when Area "A" Monitor Mode is turned off. Like option 6 this change of state occurs either at the start of the exit delay or when the Area is disarmed. Output reset time should be set to zero (P421E0E) Option 8 Keypad Duress to output #1 - This option will produce a change of state at output #1 when a Duress Alarm is activated. A Duress Alarm is activated only when the pre-defined "Duress Digit" (P197E) is prefixed to a valid Area "A" user code and entered at an Area "A" keypad. Output reset time should be set to zero (P421E0E) Note: P182E through P188E are as above but applied to outputs 2-8 PARTITION A KEYPAD OPTIONS - P189E & P190E P189E "ARM" key can disarm during exit delay - This option enables the one key disarm during exit delay feature on a keypad by keypad basis with Partition boundaries . Options 1-8 represent keypads 1-8 P190E "MONITOR" key can disarm during Monitor Mode - This options enables single button disarm of the monitor mode via the "MONITOR" key. Options 1-8 represent keypads 1-8 * * NOTE: The Duress Alarm can only reset by arming then disarming the affected area * *

P191E 1-8 Day Zone alarms to keypad buzzer (Default all) - This option will operate the keypad buzzer when a day zone is activated. The duration of the buzzer is defined at P457E. Day zones are those which are active during periods when the Area is unset. P192E 1-8 Standard zone alarms to keypad buzzer (Default all) - This option will map standard zone activations to the keypad buzzer. Normal zones are those which will only activate when the partition is set P193E 1-8 Monitor mode alarms to keypad buzzer (Default all) - This option will map activations from zones defined as Monitor Mode to the keypad buzzer. P194E 1-8 24 Hour alarms to keypad buzzer (Default all) - This option will map activations from zones defined as 24 Hour to the keypad buzzer. 24 Hour zones are those which will activate whether the Area is set or unset. P195E 1-8 Exit beeps to keypad buzzer (Default all) - This option will produce beeps at the keypad during the Exit delay. Pressing any button during the Exit period will cancel the beeps. P196E 1-8 Entry beeps to keypad buzzer (Default all) - This option will produce beeps at the keypad during the Entry Delay. Pressing the first digit of your user code will cancel the beeps. P197E 0-9 Duress Digit (Default 0) - A Duress Alarm is activated only when the "Duress Digit" defined at this address is prefixed to a valid Area "A" user code and entered at a keypad which has been assigned Area "A" permissions. The resulting Duress Alarm will unset the Area in the normal way, operate an output if one is defined and report a duress event via the communicator. Values of 0-9 may be entered at this address where 0 = option disabled and 1-9 represent the digits 1-9. PARTITION "A" TIME AND DELAY OPTIONS - P180E P180E 1E set partition when time zone ends -Default off 2E unset partition when time zone starts - Default off 3E disable monitor mode exit delay - Default off 4E disable set mode exit delay - Default off 5E disable monitor mode entry delay - Default off 6E disable set mode entry delay - Default off 7E spare 8E disable zone tampers during exit delay time-Default off Option 1 Set partition when time zone ends - this option will automatically arm partition "A" when the time zone programmed at address P170E finishes. Option 2 Unset partition when the time zone starts - this option will automatically disarm partition "A" when the tme zone programmed at address P170E starts. Option 3 Disable monitor mode exit delay. If this option is on the exit delay for partition "A" does not apply to monitor mode. Option 4 Disable set mode exit delay - if this option is on the exit delay for partition "A" does not apply when setting (the delay will still apply to monitor mode unless option 3 is also on). Option 5 Disable monitor mode entry delay - if this option is on then all zones are instant in monitor ode regardless of any entry delays programmed to zones. Option 6 Disable set mode entry delay - if this option is on then all zones are instant in full set mode regardless of any entry delays programmed to zones (entry delays will still apply to zones in monitor mode unless option 5 is also on). Option 7 Spare Option 8 Disable zone tampers during exit time.If this option is set then the zone tampers for this Partition are ignored during the exit delay(useful for monitoring zone troubles on smoke detectors) NOTE: At addresses P191E to P196E options 1-8 refer to keypads 1-8

P198E 1E Spare 2E Arm key required before code to set 3E Monitor key required before code to turn on Monitor Mode 4E Code required to arm area 5E Control function requires code 6E Control function toggles 7E Control function is momentary 8E Control shunts "Day" mode Option 1 Spare Option 2 Arm key required before code to set - This option determines if the "ARM" key must be pressed before a code is entered to set Area "A". This option must be enabled where a keypad is assigned to more than one area. Option 3 Monitor key required before code to turn on Monitor Mode - This option determines if the "MONITOR" key must be pressed before a code is entered to turn on Monitor Mode in Area "A". This option must be enabled where a keypad is assigned to more than one area. Option 4 Code required to arm area - If this option is off the partition can be shortcut armed. Shortcut arming is when the area can be set by pressing the "ARM" key only, i.e. no code is required. If this option is on, a valid Area "A" user code is required to set the area. Option 5 Control function requires code - This option determines if a code is required to operate the Control function. The Control function provides the ability to operate an output from a key press rather than from an alarm event. If this option is off, pressing the "CONTROL" key will produce an output as assigned at P181E through P188E option 5 Option 6 Control function toggles - If this function is enabled, the output which is mapped to the control function will toggle to the opposite state each time the control function is operated, i.e. if the output is on it will turn off etc. If the reset time mapped to the control output is zero the output will remain on until the control function operates again and toggles it off. If there is a reset time mapped to the control output, the output will turn off at the end of the reset time as expected. The next time the Control function is operated the output will come on again for the reset period then turn off. Option 7 Control function is momentary - If this option is enabled, the output which is mapped to the control function will turn on for the time period as determined by the value of the pulse timer mapped to the control output. Option 8 Control shunts "Day" mode - If this option is enabled, pressing the CONTROL button will shunt or override any Day mode activations. When the Control shunt is active the CONTROL light will be on. To restore the day function simply press the Control button again. Note: We advise that only one of the Control Function options be assigned at this address.

199E 1E Keyswitch Input enabled 2E Use 2nd Keyswitch 3E Keyswitch arms Area "A" 4E Pendant chirps on Area "A" Arming / disarming 5E Pendant chirps on Area "A" Monitor on / off 6E 2 second output on setting 7E 2 second output on unsetting 8E Access Control enabled even when Area "A" is set Option 1 Keyswitch Input enabled - This option will enable the Keyswitch input. Operating the Keyswitch input will arm Area "A" as determined by P199E option 3. The Keyswitch type is programmed at P201E options 3&4 Option 2 Use 2nd Keyswitch - This option will enable dual end of line configuration of the Keyswitch input and assign the high value end-of-line (8k2) to Area "A" Option 3 Keyswitch arms Area "A" - If this option is enabled, operating the Keyswitch will arm Area "A". If this option is disabled, operating the Keyswitch will turn Area "A" Monitor Mode on and off. Option 4 Pendant Chirps when arming / disarming - This option will send two short pulses (Chirps) to the output mapped at P171E - P178E option 4 when Area "A" is set via a radio key (Pendant) and four short pulses to the output when Area "A" is unset again. Option 5 Pendant Chirps when Monitor Mode on / off - This option will send two short pulses (Chirps) to the output mapped at P171E - P178E option 4 when Monitor Mode Area "A" is turned on with a radio key (Pendant) and four short pulses to the output when Area "A" Monitor Mode is turned off. Option 6 2 second output on setting - If this option is enabled, the output which is assigned by P171E6E through P178E6E will turn on for 2 seconds when Area "A" is armed. Option 7 2 second output on unsetting - If this option is enabled, the output which is assigned by P171E6E through P178E6E will turn on for 2 seconds when Area "A" is disarmed. Option 8 Access Control enabled when Area "A" set - If this option is enabled, the Access Control functions, as determined by P343E, P344E, P363E and P364E will work at all times, even when Area "A" is in the set condition. NOTE: At this address, options 3, 4 & 6 are on as default Where addresses P170E through P199E relate to Area "A", addresses P270E through P299E define the same options but relevant to Area "B" with addresses 370E through P399E relevant to Area "C"

P201E 1E Mains input AC or DC 2E Ignore Mains input 3E Low Keyswitch is momentary or latching 4E High Keyswitch is momentary or latching 5E Cabinet tamper is loop or end-of-line 6E Installer lockout 7E Area "C" is zones shared with Area "A" & "B", i.e. Area "C" is zones common to "A" & "B" 8E Local serial port speed Option 1 Mains input is AC or DC - The AC input on the panel can be 17vac @ 50hz or a DC input between 16-30v DC.This option stops the Mains fail from occurring if a DC input is applied. Option 2 Ignore Mains Input - If the panel must be run off a 12v DC supply only such as a solar application the the 12v can be applied to the battery input and the mains input is ignored. Option 3 Low Keyswitch is momentary or latching - This option determines if the low Keyswitch (4k7) is momentary or latching. If option 3 is on the low Keyswitch will be momentary (Default) Option 4 High Keyswitch is momentary or latching - This option determines if the high Keyswitch (8k2) is momentary or latching. If option 4 is on the high Keyswitch will be momentary (Default) Option 5 Cabinet tamper is loop or end-of-line - This option determines if the Cabinet tamper input uses a closed loop or 2k2 end-of-line resistor. If option 5 is on the tamper is a 2k2. (Default) Option 6 Installer lockout - If this option is enabled, the installer "Back Door" power up access to program mode will be disabled. (Default off) Option 7 Area "C" is zones shared with Areas "A" & "B" - If the system uses zones which are common to Area "A" and Area "B" then Area "C" is used for those shared zones. If zones are not shared between A & B then Area "C" is available as a independent partition. Light on = Shared Option 8 Local serial port speed - This option sets the local communications speed of the local RS232 port to be 9600bps. If this option is off the com port speed is set to 2400bps. P204E 1-255E Spare P205E 0-255E Spare P206E 1-255E Spare

P300E 1-8E Single or dual zone input - This option is used to define the Elite as an 8 or 16 zone panel where options 1-8 represent zones 1-8. If a zone is optioned on at this address it means that zone has been assigned "Zone Doubling" whereby the one zone input is used for both a low (1-8)and a high (9-16) zone. When zone doubling is used, zone 1 input is used for zones 1 & 9, Zone 2 input is used for zones 2 & 10, zones 3 input is used for zones 3 & 11 etc. Zone doubling is assigned on a zone-by-zone basis. VIBRATION SENSOR ZONE ASSIGNMENTS - P301E - P308E & P161E -P168E All 16 zones (if used) may be defined as vibration sensor zones with a vibration sensitivity level as required, although due to the interaction using dual zones with vibration sensors we recommend using a low sensitivity setting or preferrably treating the panel as an 8 zone only with up to 8 vibration zones. If a value other than zero is assigned at addresses P301E to P308E or P161 to P168 the zone which has been assigned that value automatically becomes a vibration zone. To turn a vibration zone back into a normal zone assign a zero value at the relevant address. Zero is defaulted. P301E 0-8E Zone 1 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P302E 0-8E Zone 2 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P303E 0-8E Zone 3 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P304E 0-8E Zone 4 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P305E 0-8E Zone 5 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P306E 0-8E Zone 6 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P307E 0-8E Zone 7 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P308E 0-8E Zone 8 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P161E 0-8E Zone 9 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P162E 0-8E Zone 10 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P163E 0-8E Zone 11 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P164E 0-8E Zone 12 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P165E 0-8E Zone 13 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P166E 0-8E Zone 14 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P167E 0-8E Zone 15 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. P168E 0-8E Zone 16 vibration sensitivity - Where 0 = none, 1 is highest and 8 is lowest sensitivity level. LOW ZONE ASSIGNMENTS (1-8) - P331E - P344E Combinations of options in addresses P331E to P344E may be used to give the most suitable zone behaviour. P331E 1-8E Zone is a normally open input - where options 1-8 represent zones 1-8. This option is used when normally open detectors such as smoke detectors are to connected to a zone. Default is all zones normally closed. P332E 1-8E Zone is a radio detector - Where options 1-8 represent zones 1-8. This option is used when Radio (wireless) devices are used as detectors. (Default none) P333E 1-8E Zone is in Area "A" - Where options 1-8 represent zones 1-8. This option assigns a zone to Area "A" within a partitioned system. If the system is not partitioned, all zones must be assigned to Area "A". (Default all in Area "A") See P201E7E also. P334E 1-8E Zone is in Area "B" - Where options 1-8 represent zones 1-8. This option assigns a zone to Area "B" within a partitioned system. (Default none in Area "B") See P201E7E also. If a zone is defined in both Area "A" and Area "B" it is deemed to be in Area "C" P335E 1-8E Zone is isolatable - Where options 1-8 represent zones 1-8. This option determines if a zone can be isolated or excluded either manually or via the Auto-Exclude process. (Default all on)

handover are given the unique ability to behave as both delay and instant zones. If a zone defined as an entry delay zone has been activated and the entry delay is running, a handover zone will behave as another entry delay zone with a delay time as defined at P401E to P416E. If an entry delay zone has not been activated and there is no entry delay running, a handover zone becomes an instant zone with no entry delay. (Default 2) The Handover zone MUST have an entry delay programmed. P337E 1-8E Two Trigger Zones - Where options 1-8 represent zones 1-8. A zone defined as two trigger at this address will only cause an activation if one of the following conditions are met; a The zone is triggered twice within the two trigger time period as defined by Address P451E, P452E or P453E b Any two zones defined as two trigger activate once each within the two trigger time period as defined by Address P451E, P452E or P453E c A zone defined as two trigger is left violated for longer than the two trigger time period as defined by Address P451E, P452E or P453E P338E 1-8E Zone is 24 Hour - Where options 1-8 represent zones 1-8. 24 hour zones will activate whether the panel or partition is set or unset. The entry delay can also be assigned. (Default none) P339E 1-8E Monitor Mode Zones - Where options 1-8 represent zones 1-8. Zones included at this address will become active when the panel is in Monitor Mode. Zones not assigned at this address will be excluded. (Default 1-4) Note: Monitor Mode Zones are linked to Area assignments P340E 1-8E Day Zones - Where options 1-8 represent zones 1-8. Day zones are active during periods where the panel or partitions are unset and revert to normal zones during set periods (Default none) P341E 1-8E Siren Lockout Zones - Where options 1-8 represent zones 1-8. Zones with siren lockout designation will only cause their assigned outputs to operate once per armed period. Led on = zone locked out. (Default none) P342E 1-8E Auto Exclude Zones - Where options 1-8 represent zones 1-8. Zones assigned Auto Exclude function at this address will be automatically excluded by the system if they are unsealed when the exit timers expire. Zones not given Auto Exclude status will cause an activation if they are unsealed at the end of the exit delay period. (Default all on) P343E 1-8E Access Control door position input - Where options 1-8 represent zones 1-8. (Default none) P344E 1-8E Access Control Request to exit input - Where options 1-8 represent zones 1-8. (Default none) P345E 1-8E Continuous Day Zone - Where options 1-8 represent zones 1-8. The zone acts as a dayzone at all times (Armed and Disarmed) and will operate day alarms but not normal zone alarms (Default none) P346E 1-8E Zone will report multiple activations to communicator - Default 1-8 Where addresses P331E through P346E relate to the 8 low zones, addresses P351E through P366E define the same options but relate to the 8 high zones

All timers are defined with 1 second increments. A zero (0) value at these addresses will result in a latch or no timed function at all. NOTE: All values are in seconds P401E 0-999E Zone 1 entry delay - 0-999 seconds - default 20 seconds P402E 0-999E Zone 2 entry delay - 0-999 seconds - default 20 seconds P403E 0-999E Zone 3 entry delay - 0-999 seconds - default 0 (Instant) P404E 0-999E Zone 4 entry delay - 0-999 seconds - default 0 (Instant) P405E 0-999E Zone 5 entry delay - 0-999 seconds - default 0 (Instant) P406E 0-999E Zone 6 entry delay - 0-999 seconds - default 0 (Instant) P407E 0-999E Zone 7 entry delay - 0-999 seconds - default 0 (Instant) P408E 0-999E Zone 8 entry delay - 0-999 seconds - default 0 (Instant) P409E 0-999E Zone 9 entry delay - 0-999 seconds - default 0 (Instant) P410E 0-999E Zone 10 entry delay - 0-999 seconds - default 0 (Instant) P411E 0-999E Zone 11 entry delay - 0-999 seconds - default 0 (Instant) P412E 0-999E Zone 12 entry delay - 0-999 seconds - default 0 (Instant) P413E 0-999E Zone 13 entry delay - 0-999 seconds - default 0 (Instant) P414E 0-999E Zone 14 entry delay - 0-999 seconds - default 0 (Instant) P415E 0-999E Zone 15 entry delay - 0-999 seconds - default 0 (Instant) P416E 0-999E Zone 16 entry delay - 0-999 seconds - default 0 (Instant) P417E 0-999E Area "A" exit delay - 0-999 seconds - Default 60 seconds P418E 0-999E Area "B" exit delay - 0-999 seconds - Default 60 seconds P419E 0-999E Area "C" exit delay - 0-999 seconds - Default 60 seconds P421E 0-999E Output #1 reset time - Default 600 seconds (10 min) P422E 0-999E Output #2 reset time - Default 600 seconds (10 min) P423E 0-999E Output #3 reset time - Default 600 seconds (10 min) P424E 0-999E Output #4 reset time - Default 600 seconds (10 min) P425E 0-999E Output #5 reset time - Default 0 (latching) P426E 0-999E Output #6 reset time - Default 0 (latching) P427E 0-999E Output #7 reset time - Default 0 (latching) P428E 0-999E Output #8 reset time - Default 0 (latching) P431E 0-999E Output #1 delay on timer - Default 0 (instant) P432E 0-999E Output #2 delay on timer - Default 0 (instant) P433E 0-999E Output #3 delay on timer - Default 0 (instant) P434E 0-999E Output #4 delay on timer - Default 0 (instant) P435E 0-999E Output #5 delay on timer - Default 0 (instant) P436E 0-999E Output #6 delay on timer - Default 0 (instant) P437E 0-999E Output #7 delay on timer - Default 0 (instant) P438E 0-999E Output #8 delay on timer - Default 0 (instant) P441E 0-999E Output #1 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) Times are in 1/10 second P442E 0-999E Output #2 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) increments P443E 0-999E Output #3 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) P444E 0-999E Output #4 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) P445E 0-999E Output #5 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) P446E 0-999E Output #6 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) P447E 0-999E Output #7 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) P448E 0-999E Output #8 pulse time -Default 0 (0 = Minimum 0.1 sec pulse) P451E 0-999E Area "A" Two Trigger time period - Default 60 seconds P452E 0-999E Area "B" Two Trigger time period - Default 60 seconds P453E 0-999E Area "C" Two Trigger time period - Default 60 seconds P457E 1-999E Area "A" Day Zone keypad buzzer duration - Default 2 seconds P458E 1-999E Area "B" Day Zone keypad buzzer duration - Default 2 seconds P459E 1-999E Area "C" Day Zone keypad buzzer duration - Default 2 seconds The Elite 16D provides a basic Access Control function which utilises the keypad Control Function, one of the outputs as a switching device and separate zone inputs as Request-to-Exit and door position monitoring. Address 120 sec 2 min 180 sec 3 min 240 sec 4 min 300 sec 5 min 360 sec 6 min 420 sec 7 min 480 sec 8min 540 sec 9 min 600 sec 10

as the request to exit input. Once options have been programmed, a door which is fitted with a reed switch, monitored by the zone as defined at P343E will cause a 24 hour alarm if it is opened without the Control Function being operated. Once the control function has been operated with a valid code, a door open too long (DOTL) timer is started and if the door is not closed again within the time determined by P454E (Area "A"), P455E (Area "B:) or P456E (Area "C") a 24Hr alarm will be created. The control function to output mapping is defined at addresses P181E through P188E for Area "A". P454E 1-999E Area "A" door open too long time period - default 10 sec P455E 1-999E Area "B" door open too long time period - default 10 sec P456E 1-999E Area "C" door open too long time period - default 10 sec P460E 1 - 9 9 E Delay Mains Fail Report - where the option value between 0 and 99 represent time delays from 0 to 99 minutes. A value of 0 will result in an instant report of mains failure (Default = 60) P450E 1-99E Report Delay on Zones - this delay pauses the zone reporting of alarms via the communicator for the programmed period (0 = No delay, 1-99 seconds). If the alarm is reset before this delay expires no alarms will be reported.

This block of 16 addresses is where radio PIR's and other wireless detectors are enrolled into the Elite and assigned to zones. Assigning a zone as radio at addresses P332E & P352E will enable this function and disable the zone input terminals for that specific zone on the pcb. To load a radio detector whilst in installer program mode, for example Zone 1, press P501E. The keypad will beep at 1 second intervals and the green learn mode LED on the Radio receiver board (RX-16) will flash on & off. Trigger the detector you wish to enrol at this address (Zone 1) The keypad will stop beeping and the receiver learn LED will go out when the detectors code has been stored. Repeat this sequence for all of the radio detectors moving through the addresses which correspond to the zones you require. P501E Enrol Radio Detector Zone 1 P502E Enrol Radio Detector Zone 2 P503E Enrol Radio Detector Zone 3 P504E Enrol Radio Detector Zone 4 P505E Enrol Radio Detector Zone 5 P506E Enrol Radio Detector Zone 6 P507E Enrol Radio Detector Zone 7 P508E Enrol Radio Detector Zone 8 P509E Enrol Radio Detector Zone 9 P510E Enrol Radio Detector Zone 10 P511E Enrol Radio Detector Zone 11 P512E Enrol Radio Detector Zone 12 P513E Enrol Radio Detector Zone 13 P514E Enrol Radio Detector Zone 14 P515E Enrol Radio Detector Zone 15 P516E Enrol Radio Detector Zone 16 SET RADIO DETECTOR OPTIONS - P521E - P536E This block of addresses is used to assign additional functions to the radio detectors including a low battery indication in the case of some selected detectors. P521E 1E NESS 24 bit low battery (Display's detector Battery Low condition on Keypad - NESS 24 bit only) 2E NESS Radio Reed Switch 3E CROW radio PIR battery low. 4E VISONIC radio PIR(Legacy) Battery low and tamper. 5E ELECTRONICS LINE radio PIR(Cougar).Battery low and tamper. 6E Spare 7E Spare 8E Spare Where P521E assigns options to the radio detector at zone 1, P522E assigns options to the radio detector at zone 2 etc. P521E Radio detector zone 1 options P522E Radio detector zone 2 options P523E Radio detector zone 3 options P524E Radio detector zone 4 options P525E Radio detector zone 5 options P526E Radio detector zone 6 options P527E Radio detector zone 7 options P528E Radio detector zone 8 options P529E Radio detector zone 9 options P530E Radio detector zone 10 options P531E Radio detector zone 11 options P532E Radio detector zone 12 options P533E Radio detector zone 13 options P534E Radio detector zone 14 options P535E Radio detector zone 15 options P536E Radio detector zone 16 options

In the Elite 16D we refer to wireless pendant transmitters as "Radio Keys". Because the Elite recognises each button as a separate function or user we refer to each button or user separately in that if you are loading a three button radio key, you would actually be enroling 3 separate radio users. It is possible to enrol several radio users as one where you are able to program the transmitter code of the radio key (usually via dip switches) to key them alike. Where you can not program the transmitter code of the radio keys you must enrol them as separate users. Radio users are enrolled in the same way as Radio Detectors. Press the program key then the address then the ENTER key then trigger the radio Key with the button you wish to load at that address. P541E Enrol Radio user # 1 P542E Enrol Radio user # 2 P543E Enrol Radio user # 3 P544E Enrol Radio user # 4 P545E Enrol Radio user # 5 P546E Enrol Radio user # 6 P547E Enrol Radio user # 7 P548E Enrol Radio user # 8 P549E Enrol Radio user # 9 P550E Enrol Radio user # 10 P551E Enrol Radio user # 11 P552E Enrol Radio user # 12 P553E Enrol Radio user # 13 P554E Enrol Radio user # 14 P555E Enrol Radio user # 15 P556E Enrol Radio user # 16 RADIO KEY OPTIONS 1st Set - P561E - P576E In the same way that permissions are set for user codes, Radio Keys are also assigned permissions which determine their functionality. P561E 1E Radio user #1 has Area "A" permissions (Default all) 2E Radio user #1 has Area "B" permissions 3E Radio user #1 has Area "C" permissions 4E Radio user #1 will arm 5E Radio user #1 will disarm 6E Radio user #1 will turn Monitor Mode on 7E Radio user #1 will turn Monitor Mode off 8E Radio user #1 is disabled during alarm state Option 1 Radio user #1 has Area "A" permissions - The functions set by options 4-7 will be active in Area "A" Option 2 Radio user #1 has Area "B" permissions - The functions set by options 4-7 will be active in Area "B" Option 3 Radio user #1 has Area "C" permissions - The functions set by options 4-7 will be active in Area "C" Option 4 Radio user #1 will arm - When this option is enabled, radio user #1 will arm which ever area is assigned by options 1-3

area is assigned by options 1-3 Option 6 Radio user #1 will turn Monitor Mode on - When this option is enabled, radio user #1 will turn Monitor Mode on in which ever area is assigned by options 1-3 Option 7 Radio user #1 will turn Monitor Mode off - When this option is enabled, radio user #1 will turn Monitor Mode off in which ever area is assigned by options 1-3 Option 8 Radio user #1 is disabled during alarm state - When this option is enabled, radio user #1 can not be used to reset an alarm, i.e. it must be reset at the keypad. Where P561E sets options for radio user #1, P562 sets options for radio user #2 etc P561E Radio user #1 options P562E Radio user #2 options P563E Radio user #3 options P564E Radio user #4 options P565E Radio user #5 options P566E Radio user #6 options P567E Radio user #7 options P568E Radio user #8 options RADIO KEY OPTIONS 2nd Set - P581E - P596E P581E 1E Radio user #1 turns control function on 2E Radio user #1 turns control function off (Toggles if 1 on) 3E Radio user #1 turns output on 4E Radio user #1 turns output off (Toggles if 3 ON) 5E Radio user #1 Spare 6E Radio user #1 is instant panic 7E Radio user #1 is delayed panic (1.5 sec) 8E Radio user #1 NESS 24 bit radio key battery low Option 1 Radio user #1 turns control function on - When this option is enabled, the radio user will turn on the Control Function as if it were operated from the keypad. Option 2 Radio user #1 turns control function off - When this option is enabled, the radio user will turn the control output off as if it were operated from the keypad. (Dependant on control options) Option 3 Radio user #1 turns output on - When this option is enabled, the radio user will turn on the output as assigned by P601E. Option 4 Radio user #1 turns output off - When this option is enabled, the radio user will turn off the output as assigned by P601E. This function is only valid when there is no reset time assigned to the output in question. Option 5 Spare. Option 6 Radio user #1 is instant panic - When this option is enabled, the radio user will produce an instant panic. Option 7 Radio user #1 is delayed panic - When this option is enabled, the radio user will produce a delayed panic after transmitting for 1.5 seconds. Option 8 Radio user #1 NESS 24 bit radio key battery low - This option is used to enable the low battery reporting feature of the NESS 24 bit 3 button radio key. P569E Radio user #9 options P570E Radio user #10 options P571E Radio user #11 options P572E Radio user #12 options P573E Radio user #13 options P574E Radio user #14 options P575E Radio user #15 options P576E Radio user #16 options

This block of addresses is used to map radio users to outputs in conjunction with P581E - P596E. All output modifiers such as reset timers and lock out functions are maintained and will determine the behaviour of the assigned output. P601E 1-8E Radio user #1 to output 1-8 - Where options 1-8 represent outputs 1-8 P602E 1-8E Radio user #2 to output 1-8 - Where options 1-8 represent outputs 1-8 P603E 1-8E Radio user #3 to output 1-8 - Where options 1-8 represent outputs 1-8 P604E 1-8E Radio user #4 to output 1-8 - Where options 1-8 represent outputs 1-8 P605E 1-8E Radio user #5 to output 1-8 - Where options 1-8 represent outputs 1-8 P606E 1-8E Radio user #6 to output 1-8 - Where options 1-8 represent outputs 1-8 P607E 1-8E Radio user #7 to output 1-8 - Where options 1-8 represent outputs 1-8 P608E 1-8E Radio user #8 to output 1-8 - Where options 1-8 represent outputs 1-8 P609E 1-8E Radio user #9 to output 1-8 - Where options 1-8 represent outputs 1-8 P610E 1-8E Radio user #10 to output 1-8 - Where options 1-8 represent outputs 1-8 P611E 1-8E Radio user #11 to output 1-8 - Where options 1-8 represent outputs 1-8 P612E 1-8E Radio user #12 to output 1-8 - Where options 1-8 represent outputs 1-8 P613E 1-8E Radio user #13 to output 1-8 - Where options 1-8 represent outputs 1-8 P614E 1-8E Radio user #14 to output 1-8 - Where options 1-8 represent outputs 1-8 P615E 1-8E Radio user #15 to output 1-8 - Where options 1-8 represent outputs 1-8 P616E 1-8E Radio user #16 to output 1-8 - Where options 1-8 represent outputs 1-8 DEFINING TIME ZONES - P681E - P704E This block of addresses is used to define the time zones used by outputs, users and the Auto Setting feature etc. Time zones require a start and a finish time with the effective window as the difference between start and finish. For this reason the finish time value must be higher than the start value. All times are set in 24 hour clock format. P681E 1-8E TZ1 days of the week - Where 1-7 represent the days of the week which the time zone will operate where 1 = Sunday, 2 = Monday etc. A value of 8 at this address will invert the TZ function so that instead of being effective during the window created by the start and finish times, the TZ is effective during the times outside the window set by the start and finish times. P682E 0000 - 2359E TZ1 Start time - This is the time when the TZ will start. Use 24 hour format. (HHMM) P683E 0000 - 2359E TZ1 Finish time - This is the time of day when the TZ will finish. The finish time must be greater than the start time. Use 24 hour format. (HHMM) There are 8 time zones available and they occupy addresses P681E to P704E as each time zone requires 3 addresses to be assigned. P681E TZ1 Day of the week P682E TZ1 Start Time P683E TZ1 Finish Time P684E TZ2 Day of the week P685E TZ2 Start Time P686E TZ2 Finish Time P687E TZ3 Day of the week P688E TZ3 Start Time P689E TZ3 Finish Time P690E TZ4 Day of the week P691E TZ4 Start Time P692E TZ4 Finish Time P693E TZ5 Day of the week P694E TZ5 Start Time P695E TZ5 Finish Time P696E TZ6 Day of the week P697E TZ6 Start Time P698E TZ6 Finish Time P699E TZ7 Day of the week P700E TZ7 Start Time P701E TZ7 Finish Time P702E TZ8 Day of the week P703E TZ8 Start Time P704E TZ8 Finish Time

Given that your Elite 16D controller has a real time clock compliant with minutes & hours of the day, days of the week and months of the year, it is only reasonable to assume automatic adjustments for daylight saving. This block of addresses provides the Elite 16D with the information required to perform the daylight saving adjustments as required. P712E 0-5E Daylight Saving Start Sunday - This is the Sunday number in the month that daylight saving will begin (values of 1-5 are allowed). P713E 0-12E Daylight Saving Start Month - This is month in which the above Sunday will occur.(Values of 1-12 are allowed) P714E 0-24E Daylight Saving Start Hour - This is the hour that daylight savings will begin (values of 0-24 are allowed). P715E 0-5E Daylight Saving End Sunday - This is the Sunday number in the month that daylight savings will end (values of 1-5 are allowed). P716E 0-12E Daylight Saving End Month - This is the month in which the Sunday number will occur (values of 1-12 are allowed). P717E 0-24E Daylight Saving End Hour - This is the hour that daylight savings will end (values of 0-24 are allowed. P709E Zone Response Time Setting - 1-32E. Default = 6 The input response count sets the total time the zones must be in alarm before the state is recognised by the panel. A count of 1 = 45ms. The default setting of 6 therefore results in a zone response time of 270ms. DYNAMIC DATA - P720E - P725E The addresses in the block are used to provide real time feedback from the panel as to the current status. These are intended as view only addresses and only available in installer program mode. P720E Time Zones active at this time - This address displays the time zones which are currently active in the system. P721E Misc System Flags - This address shows the status of up to 8 system operating parameters as follows 1 -7 = Spare 8 = Daylight Saving active

turned on, i.e.active P723E Display keyboard address - This option will cause the keypad you are operating to display it's address from 1-8. This feature is only available in installer program mode. P724E Display partitions assigned to this keypad - This option will cause the keypad you are operating to display the Areas to which it has been assigned permissions. P725E Display software version - This address will cause the panel software version to be flashed back at the keypad. P726E Start Event Printing - The alarm system stores the last 63 events in a printer buffer. These events include time, date and an event description. To print the events, assuming the Arrowhead serial card is plugged into the panel and connected to a printer with a RS232 input, a user with permission to print (e.g. P49-P72 option 4) enters client program mode (P-code-E, program LED on solid), then enters P726E which will send the buffer data to the printer.

This block of addresses is used to set the internal real time clock used by the time zone functions. P730E 1-7E Set day of the week - where values of 1-7 represent Sunday to Saturday (Sunday = 1) P731E 0000 - 2359E Set time - Use 24 hour format P732E 1-31E Set day of the month - where values of 1-31 represent days in the month. P733E 1-12E Set Month P734E 0-99 Set Year - Where 0-99 represent years, i.e. 97 = 1997. The Elite 16D is fully 2000 compliant so values of 00 or higher will represent the year 2000 etc. P736E W r i t e to Eeprom Board - with the optional Eeprom back-up board plugged into the serial connector on the panel and the write enable link on (on the Eeprom board) entering P736E will write a copy of the panel program files to the Eeprom board. P738E Read from Eeprom Board - this address allows a copy of a panel program files to be downloaded into a panel (note the program files must first have been copied to the Eeprom board - refer P736E) P740E 1-8E D E - mapping Outputs 1-8 - This powerful option is used to DE-map or un-assign outputs from all zone and system functions. This is a particularly useful tool when reassigning outputs to special functions such as smoke detector reset etc. In addition to removing all programmed links this option will also remove the reset time and reset the output as a latch. SET TO DEFAULTS - P741E - P745E This block of addresses is used to reset sections of the programming back to defaults. Defaults are the values set when the panel was sent from the factory. Each of the addresses in this block defaults one part of the programming. To reset the entire configuration it would be necessary to call each of the addresses in turn. P741E Reset user codes P742E Reset communicator parameters P743E Reset Radio parameters P744E Reset all other parameters

a remote control facility which allows valid users to access the panel via a standard touch tone telephone and check the set / unset status of each of the areas and operate each of the eight outputs. The Command Control feature is only available on panels fitted with one of the Speech Modules (see page 16) as the voice prompts which guide you are stored on this module. In some installations voice message storage space will be shared between the speech dial alarm event messages and the Command Control status messages. There are five program addresses which must be defined before Command Control can be effective, in addition to the process of recording the actual status messages. These program addresses are; P261E code E 4 Digit Code for Output Command Control - This is the code used to access the Output Command menu. A number from 1-8 is entered after this code to take control of an output 1-8 (for this feature to work, option 5 at addresses P101E to P108E must be turned on). P262E code E 4 Digit Code for Area "A" Command Control - This is the code used to access the Area "A" Command menu. P263E code E 4 Digit Code for Area "B" Command Control - This is the code used to access the Area "B" Command menu. P264E code E 4 Digit Code for Area "C" Command Control - This is the code used to access the Area "C" Command menu. P680E 1-9E Status Message Starting Number - This value determines the place in the Speech Module where the Command Control status messages start. On installations where the Speech Module is also used to store alarm event messages, the Command Control status messages are stored in sequence from the point where the last alarm event message finishes. For example, if there are 3 alarm event message stored in the speech module, the Command Control status messages will start at #4. In this example a value of 4 would be entered at P680E Default = 1 RECORDING STATUS MESSAGES The process for recording Command Control status messages is the same as that for recording alarm event messages except for the following critical difference. The Speech Module Command Control status message storage is divided into twenty two (22) separate areas or "slots" Each of these slots is assigned a status from the possible 22 as listed below. The content of the messages is programmable but the order in which the panel expects to find the correct message for the relevant voice prompts s pre-defined, eg if the panel was giving the status of output 1 as being "ON", it would select message number 7. 1 Area "A" Armed 2 Area "A" Disarmed 3 Area "B" Armed 4 Area "B" Disarmed 5 Area "C" Armed 6 Area "C" Disarmed 7 Output 1 On 8 Output 1 Off 9 Output 2 On 10 Output 2 Off 11 Output 3 On 12 Output 3 Off 13 Output 4 On 14 Output 4 Off 15 Output 5 On 16 Output 5 Off 17 Output 6 On 18 Output 6 Off 19 Output 7 On 20 Output 7 Off 21 Output 8 On 22 Output 8 Off To record your individual status messaged into the speech module you follow the same procedure as that for the

The messages must be recorded in the storage slots assigned that particular status For example, if you are installing a system with a Command Control requirement to remotely set and unset Area "A" (Main Alarm) as well as turn lighting on and off which is controlled by output #2, you must record appropriate status messages as follows Slot 1 "Main alarm set" Slot 2 "Main Alarm unset" Slot 9 "Lights on" Slot 10 "Lights off" You must leave blank messages at recording slots which are not to be used. In this example blank messages must be left at slots 3,4,5,6,7 & 8. Blank messages are created by pressing the record button on the speech programmer for only a moment, then releasing the button without recording an actual message. As soon as the record led comes on on the programmer you can release it again. Another example might be a system with two areas "A" (Office Alarm) and "B" Factory Alarm) as well as controlling lighting via output #1 and a furnace controlled via output 4. For this system you would record appropriate status messages as follows Slot 1 "Office Alarm set" Slot 2 "Office Alarm unset" Slot 3 "Factory Alarm set'" Slot 4 "Factory Alarm unset" Slot 7 "Lights on" Slot 8 "Lights off" Slot 13 "Furnace on" Slot 14 "Furnace off" In this example blank messages would be recorded at slots 5,6,9,10,11 & 12 Both of these examples have no alarm event messages to confuse the message recording slots. Alarm event messages used when the communicator reports in speech dial format may be stored at message slots from 1-8. Alarm event messages are recorded in order starting at slot #1 so if there are three event messages then the first Command Control status message will be stored at slot #4. In this example because there are three alarm event messages stored in record slots 1,2, & 3, the 22 Command Control status messages must therefore be stored in record slots 4-26. The table of record slots versus status messages show on page 39 must be amended to suit each site where varying numbers of speech dial alarm event messages are required. In these cases the 22 status messages are simply shuffled down the order by the number of alarm event messages required for each job on an individual basis. For example, if there are two alarm event messages they would be stored at slots 1 & 2, therefore the status message for Area "A" set would be stored at slot 3 (2+1) and the status message for Area "A" unset would be stored at slot 4 (2+2). Accordingly if a status message was required for output #5 on it would be stored at slot 17 (2+15) with the message for output #5 off stored at slot 18 (2+16). NOTE: The starting slot for the status messages must be programmed at P680E as per page 41

User operation of the Elite Command Control has been designed to be as simple and user friendly as possible with recorded voice status messages to prompt you through the 11 menu options, providing a status report of the section of the system which you are currently commanding. Because these status messages are recorded on-site they can be customised to suit each specific application. For example, rather than the status message saying "Output #1 off" you can record a message which describes exactly what is being controlled like "Factory heating off" In the previous section you would have seen how you program access codes for each of the Command Areas and outputs. These are the codes you will enter over the phone to access the command menus. In order to start the Command Control feature you must first ring the phone number which the panel is connected to. The panel may be set up to answer after a specific number of rings of it may be set-up to use a fax defeat" option. Either way, when you ring the phone number and finally get through to the Elite, the first thing you will hear over the phone is a burst of modem tone. The panel produces this tone in order to communicate with the upload download option. After 5 seconds this tone will stop and you must enter the access code which is associated with the Command menu option you wish to access. Remember, the code you enter will determine which menu option you access. If you miss the pause, the communicator will repeat the modem tone and then again pause for 5 seconds looking for your access code. This process will be repeated 4 times before hanging up if no valid code is received. When entering codes or other information in Command Control the "#" key acts as a "Clear" button When you have entered the required 4 digit access code the communicator will reply with the status message associated with that menu option. For example, lets say we have a code of 2045 programmed at address P262E, we would use this code to set and unset Area "A" of the alarm system. If we had a status message recorded at slot 1 which said "Main alarm set" and one at slot 2 which said "Main alarm unset" When we ring through to the panel and we enter the code 2045, we would hear the message "Main alarm set" or "Main alarm unset" depending on the actual status of Area "A" Once you have reached the desired menu and the status message has informed you of the actual state, you can use the "*" key to toggle the option on & off or set and unset,eg in our example above, code 2045 accesses the Area "A" menu and lets say the status message we received was "Main alarm unset" If we press the "*" key, Area "A" will be armed with exit delay etc and we would receive a status message "Main alarm set". If we had accessed one of the output menus we could turn ancillary devices like lighting etc on and off with the "*" key in the same way. While you are on-line with the panel you can move between menu options by entering the code of the option you want to move to. For example in the examples above, we had a code of 2045 programmed to give us access to Area "A". Lets say we have a code of 4321programmed to access Output #1 which is interfaced to the factory lighting. While we are on-line in the Area "A" menu which we accessed with the 2045 code, if we enter the 43211 code we will be transported to the Output #1 menu and would hear the status message which had been programmed for the state of the factory lights (Note; For output control you must enter in the 4 digit code eg 4321 followed by the output number you wish to control, in this case 1). As in the previous example where we used the "*" key to toggle the alarm between set and unset, we can use the "*" key to toggle the output on and off. As you toggle the output on and off you would hear the status message "Factory lights on" and "Factory lights off". To end a Command Control session simply hang up the phone. The communicator is monitoring the line at all times and 15 seconds after the last key press it will automatically hang up the line. This 15 second timer is active during the whole command control process so a period of 15 seconds without a key press will cause the panel to hang-up. The "#" key is used as a "Clear" button at all stages during command control so if you make a mistake or enter your code incorrectly, all you have to do is press the # key and start again. LOCAL COMMAND CONTROL OF OUTPUTS If a command control code for outputs is programmed (P261E) and the output/s are allowed to be locaaly controlled (P101-P108, option 6) then entering the 4 digit code at a keypad will blank the display and the zone led’s will now indicate the output status eg if output 1 is on zone 1, led will be on. By now pressing the “1” button, output 1 can be turned off provided it is allowed to be locally controlled.

alarm events are reported. This flexibility includes options or reporting a central monitoring station using Ademco Contact ID format, a domestic reporting option using alternating siren tones, a format for reporting alarms to an alpha numeric pager and a powerful speech dialler. In accordance with the statutory requirements of the Telepermit standards we must bring the following points to your attention; A readily accessible disconnect device shall be incorporated into the 230V fixed wiring. In the event of any problem with this device, the by-pass switch should be operated. The user is to then arrange with the installer of the device to make the necessary repairs. Should the matter be reported to Telecom as a wiring fault, and the fault be proven to be due to the alarm panel, a call out charge will be incurred. Should the Elite control panel require relocation the Telecom connection must be disconnected before the power is disconnected. Similarly when reconnecting the dialler, it is necessary to power up the Elite before connecting the dialler to the Telecom Network. Connection to the Telecom network should be made in accordance with Access Standards Newsletter #65 dated November 1993. This connection is to be readily accessible to allow disconnection in the event of a fault. An example of this connection method is shown below. NOTE: The telephone line must not enter the cabinet through the same cable entry hole as any 230 volt mains cables. A separate cable entry must be used for 230 volt cabling When using one of the knock-outs around the side of the cabinet for supply entry, a suitable bushing must be used where the supply cables pass through a knock-out. The transmit level from this device is set at a fixed level and because of this there may be circumstances where this device does not give its optimum performance. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and do not report a fault unless the telephone performance is impaired. This automatic dialling equipment shall not be set up to make calls to the Telecom "111" Emergency Service

each of the six possible phone numbers. 1 Ademco Contact ID Reporting Format - This is a high speed, DTMF format used to report alarm events to a commercial monitoring station equipped with a computerised receiver. This format can only be kissed-off by the monitoring company receiver. 2 Elite Domestic Dial Format - This format has ben developed to provide a basic, low cost means of reporting alarm events up to 6 private phone numbers which does not require any additional receiving equipment. Domestic dial will only report zone activations, panic alarms and battery low alarms. When the communicator uses this domestic dial format to report an event an alternating siren type, alarm tone will be heard over the telephone. This alternating alarm tone continues for 5 seconds followed by a 5 second pause in which the communicator is looking for a kiss-off. If a kiss-off is not received another round of alarm tones will be sent followed by another pause to check for kiss-off. This routine is repeated 4 times, at which point if a kiss-off has not been received, the communicator will hang up and dial the next phone number. To kiss-off the communicator during the pause period, all you do is press one of the buttons on your touch tone telephone. 3 Pager Format - This format is used to report the same alarm events as the Domestic Dial format above but the report is sent to an Alpha / Numeric pager. The event report is in the form of a 12 bit message which consist of an unique 4 digit account code, a 3 digit event code and a 3 digit identifier extension. The account code is used to identify the panel which is calling, the event code is used to identify the type of alarm event and the extensions used to identify the zone or user number. The spaces between the account code, event code and extension make up the 12 bits of the message. Note- There is no kiss-off required in Pager Format reporting. As an example, a pager which displays this message; 1 2 3 4 1 3 0 0 0 1 Would have received an alarm message from alarm 1234 (1234) that there is a burglar activation (130) on zone one (001) The event codes and their meanings are listed on page 52. 4 Speech Dial Format - This format is similar to the Elite Domestic Dial format in that it reports alarm events via private phone numbers and is kissed-off by pressing a button on the telephone but there is one important difference. This format will report the alarm events using a combination of up to eight pre-recorded voice messages. These messages are recorded directly into the speech module which is a "plug on" option to your Elite 16D control communicator. Speech modules are available in versions of 20 second and 90 second recording capacity. When an alarm event is reported using the Speech Dial format the messages assigned at addresses P660E to P679E are played and like the Domestic Dial format a 5 second pause follows in which the communicator is looking to be kissed-off. If not kissed-off the communicator will repeat the messages and pause again. This routine is repeated 4 times at which point, if a kiss-off has not been received the communicator will hang up and dial the next phone number. To kiss-off the communicator during the pause period all you do is press one of the buttons on your touch tone telephone. If a kiss-off is not received from any of the phone numbers dialled, the communicator will make a maximum of twenty calls and shut down. The communicator will also shut down if the control panel is reset with a valid code before a kiss-off is received EXCEPT reporting in Contact ID format.

In order to provide you with the most convenient way of assigning one or more of these possible formats to each alarm event, we have developed a unique system called "Reporting Scenarios" These Scenarios define what action is taken by the communicator for each alarm event, eg.alternate call numbers 1&2 until one is kissed-off or dual report to numbers 1&2 until both kissed-off There are four individual scenarios available each with up to 16 possible steps. The method of programming the scenarios is to associate a phone number with an action for kiss- off and or no kiss-off. Phone numbers are assigned values from 1 to 6 which leaves 4 values for the actions. Scenario Options 1 = Call Telephone Number 1 2 = Call Telephone Number 2 3 = Call Telephone Number 4 5 = Call Telephone Number 5 6 = Call Telephone Number 6 7 = Return to step 1 until all numbers are kissed-off 8 = Return to previous step if not kissed-off 9 = Stop if kissed-off 0 = Stop whether kissed-off or not kissed-off Example 1 (alternate reporting) 1 9 2 9 7 In this example we have defined a scenario with five actions as follows. The dialler will alternate between phone numbers 1 & 2 until kissed off. Example 2 (dual reporting) 2 4 7 In this example we have defined the three following actions. The dialler will alternate between phone numbers 1 & until both numbers have been kissed off. If the last step in a scenario is reached and there is no instruction to define what the communicator is to do it will stop. You must therefore include either 7 or 8 if you want the dial routine or part of the routine repeated. Step # Option # Action 1 1 Call phone number 1 2 9 Stop if kissed-off 3 2 If not kissed-off call phone number 2 4 9 Stop if kissed-off 5 7 Return to step 1 until all numbers are kissed-off Step # Option # Action 1 2 Call phone number 2 2 4 Call phone number 4 3 7 Return to step 1 until all numbers are kissed-off

scenarios for you to copy. Because the defaults of the panel assign Reporting Scenario #1 to all zone activations, tamper activations and system events etc it it advisable to make the required alterations to Scenario #1 (P211E) should you require a different dialling sequence. Once you decide what is the most appropriate scenario for each installation, choose it from the following list , or create it from scratch and program it at Address P211E. Any "Special" zones or events can have other scenarios created and assigned on an individual basis as required. COMMUNICATOR REPORTING SCENARIOS - P211E - P214E P211E 1-16E Reporting Scenario #1 options (See options on page 46)Default=1 9 2 9 7 P212E 1-16E Reporting Scenario #2 options (Default = 0) P213E 1-16E Reporting Scenario #3 options (Default = 0) P214E 1-16E Reporting Scenario #4 options (Default = 0) MAXIMUM DIAL ATTEMPTS PER SCENARIO P215E Maximum dialling attempts for Scenario 1-Value 1-99 (Default=10) P216E Maximum dialling attempts for Scenario 1-Value 1-99 (Default=10) P217E Maximum dialling attempts for Scenario 1-Value 1-99 (Default=10) P218E Maximum dialling attempts for Scenario 1-Value 1-99 (Default=10) PROGRAM TELEPHONE NUMBERS - P221E - P226E There are 16 characters available in each of the telephone number strings including the special codes P221E 1-16E Telephone Number 1 - where options 1-16 represent up to 16 digits P222E 1-16E Telephone Number 2 - where options 1-16 represent up to 16 digits P223E 1-16E Telephone Number 3 - where options 1-16 represent up to 16 digits P224E 1-16E Telephone Number 4 - where options 1-16 represent up to 16 digits P225E 1-16E Telephone Number 5 - where options 1-16 represent up to 16 digits P226E 1-16E Telephone Number 6 - where options 1-16 represent up to 16 digits From time to time it is necessary to program special codes within the telephone number string. These codes include a 2.5 second pause, the * and # characters and a new option called "Wait for 2nd dial tone" Use the following table to select and program special characters as required. Scenario Code Actions Std Monitoring Company 1 9 2 9 7 Alternate calling until kissed-off 4 Number Speech Dial 1 9 2 9 3 9 4 9 7 Call 4 numbers in sequence until kissed-off Plant Monitoring via Pager 1 0 Call pager once then stop( kiss-off not required ) Dual Reporting 1 7 2 7 Call number 1 & if kissed off call number 2 Monitoring Co if Speech Not Kissed-off 1 9 2 9 3 8 If no kiss-off from speech dial number, (phone #. 1 & 2) then dial monitoring company until kissed off (Phone #. 3 Character Button Displayed As 2.5 sec pause CONTROL Control * Character MEMORY Memory # Character PANIC Line Wait for 2nd Dial Tone ARM Armed

This group of addresses is used to define which format the communicator will use when contacting each of the six phone numbers on an individual basis. For example phone number 1 may be a speech dial report to a domestic home with numbers 2 and 3 reporting in Contact ID to a monitoring company P231E 1-8E Define Reporting Format for Phone Number 1 1 = Ademco Contact ID (Default) 2 = Domestic Alarm Tone 3 = Pager 4 = Speech Dialler 5 = Spare 6 = Monitor "Call Progress" (Default) 7 = Spare 8 = Spare Option 1 Ademco Contact ID - Use Contact ID format to report alarm and system events to a monitoring companies receiving equipment. Option 2 Domestic Alarm Tone - Use "Domestic" format to report alarm events. This format uses alternating alarm tones to report and can be kissed-off by pressing any digit key on a touch tone phone. Option 3 Pager - Report alarm events using "Pager" format. This format utilises Telecom's 026 pager network or other public subscriber networks like Answerscan etc, to post numeric messages to a compatible pager.(NOTE:The client account number should not start with a “0”) When an event is received by a pager it will display the alarm system account code followed by and event code followed by a zone or user designation. For example - 1234 130 004 displayed on a pager would correspond to a zone 4 activation from a system with account code 1234. The event codes are listed in the Communicator Program Summary section of this manual. Option 4 Speech Dialler - Report alarm events by using the optional add-on speech dialler module. This module is available is either 20 or 90 second versions can be kissed-off by pressing any digit key on a touch tone phone. The first 8 recording slots may be reserved for alarm messages which are mapped to events at addresses P660E to P676E The Elite "Command Control" feature utilises the same speech dialler module to provide voice prompted control and status reporting of your alarm system via a standard touch tone telephone. These voice prompts are stored at recording slots which follow in order on from the alarm event messages. The 90 second speech module is particularly useful where a speech dialler is used to report alarm events and Command Control is used to control a large number of functions such as setting and unsetting on an area basis and operating outputs to control lighting, or heating etc. Option 5 Spare - This option is reserved for future developments Option 6 Monitor Call Progress - When this option is enabled, the Elite communicator monitors the call progress to determine if the destination phone number is ringing, engaged or disconnected. As a result, if the number is engaged or disconnected the communicator will more on to the next number immediately rather than timing out after a pre-determined wait period. Option 7 Spare - This option is reserved for future developments Option 8 Spare P232E 1-8E Define Reporting Format for Phone Number 2 (Default 1&6) P233E 1-8E Define Reporting Format for Phone Number 3 P234E 1-8E Define Reporting Format for Phone Number 4 P235E 1-8E Define Reporting Format for Phone Number 5 P236E 1-8E Define Reporting Format for Phone Number 6

This group of addresses is used to map activations from each of the 16 possible alarm zones to one of the 4 possible reporting scenarios. If a value of zero (0) is assigned at an address in this block, alarms from that zone will not be reported by the communicator. P241E 1-4E Zone 1 Activations mapped to Scenario 1-4 - Default 1 P242E 1-4E Zone 2 Activations mapped to Scenario 1-4 - Default 1 P243E 1-4E Zone 3 Activations mapped to Scenario 1-4 - Default 1 P244E 1-4E Zone 4 Activations mapped to Scenario 1-4 - Default 1 P245E 1-4E Zone 5 Activations mapped to Scenario 1-4 - Default 1 P246E 1-4E Zone 6 Activations mapped to Scenario 1-4 - Default 1 P247E 1-4E Zone 7 Activations mapped to Scenario 1-4 - Default 1 P248E 1-4E Zone 8 Activations mapped to Scenario 1-4 - Default 1 P249E 1-4E Zone 9 Activations mapped to Scenario 1-4 - Default 1 P250E 1-4E Zone 10 Activations mapped to Scenario 1-4 - Default 1 P251E 1-4E Zone 11 Activations mapped to Scenario 1-4 - Default 1 P252E 1-4E Zone 12 Activations mapped to Scenario 1-4 - Default 1 P253E 1-4E Zone 13 Activations mapped to Scenario 1-4 - Default 1 P254E 1-4E Zone 14 Activations mapped to Scenario 1-4 - Default 1 P255E 1-4E Zone 15 Activations mapped to Scenario 1-4 - Default 1 P256E 1-4E Zone 16 Activations mapped to Scenario 1-4 - Default 1 MULTIPLE ZONE REPORTING - P346E & P366E P346E 1-8E Zone will report multiple activations to communicator for zones 1-8 (Default ON) P366E 1-8E Zone will report multiple activations to communicator for zones 9-16 (Default ON) ZONE EXCLUDE SCENARIO MAPPING - P461E - P476E This group of addresses is used to map zone excludes (isolations) from each of the 16 possible alarm zones to one of the 4 possible reporting scenarios. If a value of zero (0) is assigned at an address in this block, excludes from that zone will not be reported by the communicator. P461E 1-4E Zone 1 Exclude mapped to Scenario 1-4 - Default 1 P462E 1-4E Zone 2 Exclude mapped to Scenario 1-4 - Default 1 P463E 1-4E Zone 3 Exclude mapped to Scenario 1-4 - Default 1 P464E 1-4E Zone 4 Exclude mapped to Scenario 1-4 - Default 1 P465E 1-4E Zone 5 Exclude mapped to Scenario 1-4 - Default 1 P466E 1-4E Zone 6 Exclude mapped to Scenario 1-4 - Default 1 P467E 1-4E Zone 7 Exclude mapped to Scenario 1-4 - Default 1 P468E 1-4E Zone 8 Exclude mapped to Scenario 1-4 - Default 1 P469E 1-4E Zone 9 Exclude mapped to Scenario 1-4 - Default 1 P470E 1-4E Zone 10 Exclude mapped to Scenario 1-4 - Default 1 P471E 1-4E Zone 11 Exclude mapped to Scenario 1-4 - Default 1 P472E 1-4E Zone 12 Exclude mapped to Scenario 1-4 - Default 1 P473E 1-4E Zone 13 Exclude mapped to Scenario 1-4 - Default 1 P474E 1-4E Zone 14 Exclude mapped to Scenario 1-4 - Default 1 P475E 1-4E Zone 15 Exclude mapped to Scenario 1-4 - Default 1 P476E 1-4E Zone 16 Exclude mapped to Scenario 1-4 - Default 1 LOW ZONE TAMPERS SCENARIO MAPPING - P481E - P488E

scenarios. If a value of zero (0) is assigned at an address in this block, low tampers from that zone input will not be reported by the communicator. Low Zone Tamper is a short circuit input. P481E 1-4E Low Zone 1 Tamper Alarms mapped to Scenario 1-4 - Default 1 P482E 1-4E Low Zone 2 Tamper Alarms mapped to Scenario 1-4 - Default 1 P483E 1-4E Low Zone 3 Tamper Alarms mapped to Scenario 1-4 - Default 1 P484E 1-4E Low Zone 4 Tamper Alarms mapped to Scenario 1-4 - Default 1 P485E 1-4E Low Zone 5 Tamper Alarms mapped to Scenario 1-4 - Default 1 P486E 1-4E Low Zone 6 Tamper Alarms mapped to Scenario 1-4 - Default 1 P487E 1-4E Low Zone 7 Tamper Alarms mapped to Scenario 1-4 - Default 1 P488E 1-4E Low Zone 8 Tamper Alarms mapped to Scenario 1-4 - Default 1 HIGH ZONE TAMPERS SCENARIO MAPPING - P491E - P498E This group of addresses is used to map the eight possible High zone tampers to one of the four possible reporting scenarios. If a value of zero (0) is assigned at an address in this block, high tampers from that zone input will not be reported by the communicator. High Zone Tamper is an open circuit input. P491E 1-4E High Zone 1 Tamper Alarms mapped to Scenario 1-4 - Default 1 P492E 1-4E High Zone 2 Tamper Alarms mapped to Scenario 1-4 - Default 1 P493E 1-4E High Zone 3 Tamper Alarms mapped to Scenario 1-4 - Default 1 P494E 1-4E High Zone 4 Tamper Alarms mapped to Scenario 1-4 - Default 1 P495E 1-4E High Zone 5 Tamper Alarms mapped to Scenario 1-4 - Default 1 P496E 1-4E High Zone 6 Tamper Alarms mapped to Scenario 1-4 - Default 1 P497E 1-4E High Zone 7 Tamper Alarms mapped to Scenario 1-4 - Default 1 P498E 1-4E High Zone 8 Tamper Alarms mapped to Scenario 1-4 - Default 1 SYSTEM EVENTS SCENARIO MAPPING - P311E - P320E This group of addresses is used is used to map the ten possible System Events as listed below to one of the four possible reporting scenarios. If a value of zero (0) is assigned at an address in this block, that event will not be reported by the communicator. P311E 1-4E Keypad Panic mapped to Scenario 1-4 - Default 1 P312E 1-4E Battery low mapped to Scenario 1-4 - Default 1 P313E 1-4E 230v Mains failure mapped to Scenario 1-4 - Default 1 P314E 1-4E Phone line restore mapped to Scenario 1-4 - Default 1 P315E 1-4E Radio PIR Battery Low mapped to Scenario 1-4 - Default 1 P316E 1-4E Radio Key Battery Low mapped to Scenario 1-4 - Default 1 P317E 1-4E Keypad Tamper mapped to Scenario 1-4 - Default 1 P318E 1-4E Cabinet Tamper mapped to Scenario 1-4 - Default 1 P319E 1-4E Radio Panic mapped to Scenario 1-4 - Default 1 P320E 1-4E Communicator Test Calls mapped to Scenario 1-4 - Default 1 REPORT DELAY ON MAINS FAIL P460E 1-99E Mains failure report delay 0-99 minutes - Default = 60 AREA BASED REPORTING SCENARIOS - P322E - 327E

events to one of the four possible scenarios Multiple options can be assigned to the Area or partition based addresses but only one value (1-4) can be assigned to the scenario mapping addresses. REPORT DELAY ON ZONE ALARMS P450E 0-99E Zone Dialler Reporting Delay - Default = 0 This delay pauses the reporting of zone alarms for all reporting formats. This delay can be used to prevent false alarms from reporting if the alarm is cancelled before this delay expires.

2 = Send Monitor On/ Off 3 = Send Unset only after activations 4 = Send Duress Alarms 5 = Enable 24hr alarms to voice/domestic 6 = send set immediately 7 = Spare 8 = Spare Option 1 Send Set / Unset - If this option is enabled, the communicator will report Area "A" sets and unsets following the steps as determined by the reporting scenario assigned by P323E Option 2 Send Monitor On / Off - If this option is enabled, the communicator will report Area "A" monitor on and monitor off events following the steps as determined by the reporting scenario assigned by P323E Option 3 Send Unsets only after activation - If this option is enabled, the communicator will report Area A unsets (opens) after alarm activation only. This option is often used in conjunction with alarm only reporting. Option 4 Send Duress Alarms - If this option is enabled, the communicator will report Duress Alarms as defined by address P197E Option 5 Enable 24hr Alarms to Voice/Domestic - If this option is enabled, then 24hr zone alarms will report using voice or domestic alarm tone reporting even when the alarm is unset. Option 6 Send Set Immediately - If enabled, the communicator will report a set immediately the panel is armed. If not enabled, the set report is sent at the expiry of the exit delay. Option 7 Spare Option 8 Spare P323E 1-4E Area "A" Reports mapped to Scenario 1-4 - This option is used to map Area "A" reports as defined by P322E to one of the four possible reporting scenarios - Default 1 P324E 1-8E Area "B" Reporting Options - Default 1,2&4 P325E 1-4E Area "A" Reports mapped to Scenario 1-4 - Default 1 P326E 1-8E Area "C" Reporting Options - Default 1,2&4 P327E 1-4E Area "C" Reports mapped to Scenario 1-4 - Default 1 SYSTEM REPORTING OPTIONS - P329E, P260E, P264E, P265E & P266E This block of addresses is used to define a number of global system options. Multiple options may be assigned at address P260E P329E 1-99E Auto-Answer Rings - This options defines the number of rings before the communicator will auto-answer the incoming call. A value of zero (0) at this address will disable auto-answer. - Default = 0 P260E 1-8E System Options 1 = Enable Communicator 2 = DTMF or Decadic 3 = NZ style Decadic 4 = Blind Dial 5 = Send Restores 6 = Use Group code or Multiple Accounts 7 = Fax defeat 8 = Disable line monitoring

option is not assigned, all communicator activity, including recording messages on the speech dialler module, will be disabled. - Default = Communicator Off Option 2 DTMF or Decadic.Selects touchtone dialling.led must be ON Option 3 NZ Style Decadic - With this option off, the deladic pulses are NZ style pulses. If the option is on, then the pulses are reversed Option 4 Blind Dial - If this option is selected, the communicator will make a dial attempt even if it can not detect a valid dial tone. If this option is not selected the communicator will seize the phone line and listen for dial tone. If dial tine is not present the communicator will release (Hang up) the line wait five seconds and repeat the process. If dial tone is still not present after 3 attempts the communicator will Blind Dial. On = Blind Dial, off = Standard Dial. - Default = Off Option 5 Send Restores - If this option is selected restores will be reported for all events. If this option is not selected restores will be disabled. On = Send Restores, off = No Restores. - Default = On Option 6 Use Group Codes or Multiple Accounts - This option is used to determine if system using multiple Areas will use Group Code reporting to one account number or report individual Area activity to individual account numbers. Option 6 on = group code and option 6 off = multiple account numbers - Default = Off. Option 7 Fax Defeat - This option enables fax defeat mode. When enabled the panel will look for incoming rings between 2-6 rings (inclusive). If the incoming call is then terminated the panel will answer the next incoming call within 2 rings. If another call is not established within 60 sec of the first call, the fax defeat mode is reset. For fax defeat to work the auto answer rings must be enabled by putting in a suitable ring count (eg 15). Option 8 Disable Line Monitoring -If this option is enabled, then the panel no longer tests the telephone line. AREA ACCOUNT CODES - P266E - P268E P266E XXXXE Account Code for Area "A" Reports - The Account code set at this address will be used to report all system events sets and unsets, zone activations, restores and excludes etc from Area "A" - Default Account = 0000 P267E XXXXE Account Code for Area "B" Reports - The account code set at this address will be used to report sets and unsets, zone activations, restores and excludes etc from Area "B" P268E XXXXE Account Code for Area "C" Reports - The account code set at this address will be used to report sets and unsets, zone activations, restores and excludes etc from Area "C" COMMAND CONTROL CODES P261E - P264E P261E XXXXE DTMF Command Output Control Code - This is a 4 digit code used to control the 8 outputs either locally (set by options P101 - P108 opt 6) or by DTMF remote (set by options P101 - P108 opt 5) P262E XXXXE DTMF Command Code For Area A - This is a 4 digit code used to remotely set/unset Area A. P263E XXXXE As per P262E but controls Area B. P263E XXXXE As per P262E but controls Area C. P680E 1-9E Starting message number to command control voice prompts.

definable events your Elite V4 control communicator can report. P620E XXXE Duress Alarm Default = 121 P621E XXXE Zone 1 Activation Default = 130 0 = No Report P622E XXXE Zone 2 Activation Default = 130 P623E XXXE Zone 3 Activation Default = 130 P624E XXXE Zone 4 Activation Default = 130 P625E XXXE Zone 5 Activation Default = 130 P626E XXXE Zone 6 Activation Default = 130 P627E XXXE Zone 7 Activation Default = 130 P628E XXXE Zone 8 Activation Default = 130 P629E XXXE Zone 9 Activation Default = 130 P630E XXXE Zone 10 Activation Default = 130 P631E XXXE Zone 11 Activation Default = 130 P632E XXXE Zone 12 Activation Default = 130 P633E XXXE Zone 13 Activation Default = 130 P634E XXXE Zone 14 Activation Default = 130 P635E XXXE Zone 15 Activation Default = 130 P636E XXXE Zone 16 Activation Default = 130 P641E XXXE Zone 1 Low Tamper Default = 137 0 = No Report P642E XXXE Zone 2 Low Tamper Default = 137 P643E XXXE Zone 3 Low Tamper Default = 137 P644E XXXE Zone 4 Low Tamper Default = 137 P645E XXXE Zone 5 Low Tamper Default = 137 P646E XXXE Zone 6 Low Tamper Default = 137 P647E XXXE Zone 7 Low Tamper Default = 137 P648E XXXE Zone 8 Low Tamper Default = 137 P651E XXXE Zone 1 High Tamper Default = 137 0 = No Report P652E XXXE Zone 2 High Tamper Default = 137 P653E XXXE Zone 3 High Tamper Default = 137 P654E XXXE Zone 4 High Tamper Default = 137 P655E XXXE Zone 5 High Tamper Default = 137 P656E XXXE Zone 6 High Tamper Default = 137 P657E XXXE Zone 7 High Tamper Default = 137 P658E XXXE Zone 8 High Tamper Default = 137 ALARM VOICE MESSAGE MAPPING - P660E - P679E This block of addresses is used to assign up to eight possible voice messages to the Panic alarm battery low and 16 zone activation's. More than one message can be assigned to each zone activation. The voice messages will be replayed over the phone in response to an alarm activation to those phone numbers which have been assigned Speech Dial format at options P231E to P236E More than one message may be assigned to an alarm event however, if multiple messages are assigned to one event, the messages will be replayed in numerical order. For example, if message #1 said "Fire" and message #5 said "Activation at Acme premises" and if both messages were mapped to Zone 1 activation's (P661E15E) the replay message in response to a zone 1 activation would be heard as "Fire alarm at Acme premises" It is possible to map up to eight messages to an alarm event but it should be noted that they will always be replayed in numerical order so when recording your messages into the speech module, you must organise the messages in the correct order. P660E 1-8E Voice Messages Mapped to Panic Alarm - Default 1 P661E 1-8E Voice Messages Mapped to Zone 1 Activation's - Default 1

P663E 1-8E Voice Messages Mapped to Zone 3 Activation's - Default 1 P664E 1-8E Voice Messages Mapped to Zone 4 Activation's - Default 1 P665E 1-8E Voice Messages Mapped to Zone 5 Activation's - Default 1 P666E 1-8E Voice Messages Mapped to Zone 6 Activation's - Default 1 P667E 1-8E Voice Messages Mapped to Zone 7 Activation's - Default 1 P668E 1-8E Voice Messages Mapped to Zone 8 Activation's - Default 1 P669E 1-8E Voice Messages Mapped to Zone 9 Activation's - Default 1 P670E 1-8E Voice Messages Mapped to Zone 10 Activation's - Default 1 P671E 1-8E Voice Messages Mapped to Zone 11 Activation's - Default 1 P672E 1-8E Voice Messages Mapped to Zone 12 Activation's - Default 1 P673E 1-8E Voice Messages Mapped to Zone 13 Activation's - Default 1 P674E 1-8E Voice Messages Mapped to Zone 14 Activation's - Default 1 P675E 1-8E Voice Messages Mapped to Zone 15 Activation's - Default 1 P676E 1-8E Voice Messages Mapped to Zone 16 Activation's - Default 1 P679E 1-8E Voice Message Mapped to Battery Low Alarm - Default 0 P718E XXXXXXXX. Up to 8 digit security code for upload/download. P719E Upload/Download options 1E Data transfer is allowed -Default on 2E Can get data "from panel" - Default on 3E Can send data "to panel" - Default on 4E Can monitor keypad activity - Default on 5E Can monitor panel status - Default on 6E Can change panel status - Default on 7E Can clear event buffer 8E V21/Bell103 Option 1 Data Transfer is Allowed - this option must be on for ANY panel -pc data transfer to occur (if off connection can still be achieved with P728E command as below). Option 2 Can Get Data "From Panel" - this option must be on to allow the pc to retrieve programmed data from the panel. Option 3 Can Send Data "To Panel" - to allow changes to be sent to the panel from the pc, this option plus options 1 & 2 must be on. Option 4 Can Monitor Keypad Activity - this option allows an operator to view the last 16 keypad buss entries at a panel via a dial-up link. To work this option plus options 1 & 2 must be on. Option 5 Can Monitor Panel Status - this option allows display of the partitions, zones, outputs, mains and battery status. The option must be on with options 1 & 2. Option 6 Can Change Panel Status - this option allows control of setting/unsetting for partitions A,B & C, control of the 8 outputs and excluding of zones via the pc upload/download dial up link. This option must be on with options 1,2 & 5. Option 7 Can clear event buffer-this option allows the user to clear the panels event buffer from the PC Option 8 V21/Bell103-if this option is off Bell103 format is selected,if on V21 format is selected.The choice of either 300Baub format is dependent upon your modem.

client program mode and the telephone line is currently ringing the panel will answer the incoming call and initiate an upload/download connection (overrides P719E opt 1-6 setting) PROGRAMMING TEST CALL OPTIONS - P706E - P707E Because the Elite 16D runs a real time clock, it is possible to assign test calls by day of the week and time of day rather than the more common practice of spacing test calls so many hours apart,. P706E 0-7E Test Call Days of the Week - Where 1 = Sunday and 7 = Saturday. 0 = No Test P707E XXXXE Test Call Time of Day - Where the time of the day you wish the panel to make its daily test call is programmed in 24 hour format. P727E Keypad Listen-in Options-Default = off 1 = While dialling 2 = During Entire call 3 = At all times 4 = Spare 5 = Spare 6 = Spare 7 = Spare 8 = Spare Medical Alarm 100 Low Temperature 159 Medical Pendant 101 High Temperature 158 Fire Alarm 110 Refrigeration Alarm 152 Smoke Detector 111 Water Leakage 154 Heat Detector 114 Gas Detector 151 Manual Call Point 115 Duct Detector 116 Silent Panic 122 Audible Panic 123 Perimeter Zone 131 24 Hour Zone 133 Entry Exit Zone 134

event codes with extensions pre-defined as listed below. This extensions list is for your reference only and can not be re-assigned. Event Code Extension Comment Cabinet Tamper 137 120 Panel & Sat Tamper etc Zone Tamper - Low (short circuit) 137 001 to 008 Zones 1-8 Zone Tamper - High (open circuit) 137 009 to 016 Zones 1-8 Keypad Tamper (Wrong Code) 137 101 At keypad #1 102 At keypad #2 through to 108 At keypad #8 Keypad Panic 120 101 At keypad #1 102 At keypad #2 through to 108 At keypad #8 Arm by "ARM key (shortcut) 401 000 User number zero Arm by user code 401 001 User #1 002 User #2 through to 024 user #24 Arm by Radiokey 401 051 Radio User #1 052 Radio User #2 through to 066 Radio User #16 Arm by Command Control (remote set) 401 090 Command Control user Arm by Time Zone 403 98 Time Zone User Number Arm by Keyswitch 409 91 Keyswitch Arm/Disarm User#91 Arm by Up/Download 401 99 Remote User Number Radiokey Panic 120 120 All radio panics Radio PIR / Reed Switch Activation 130 001 Zone 1 002 Zone 2 through to 016 Zone 16 System Battery Low 302 000 Control Panel Battery low Mains Fail 301 000 230v mains to control panel lost Radio PIR / Reed Switch Battery Low 384 001 Zone 1 002 Zone 2 through to 016 Zone 16 Radiokey Battery Low 384 051 Radiokey #1 052 Radiokey #2 053 Radiokey #3 through to 066 Radiokey #16 TEST Calls 602 000 24 hour test Zone Excludes 570 001 Exclude Zone 1 002 Exclude Zone 2 through to 016 Exclude Zone 16 Phone Line Failure 351 000 Reported when line is restored Monitor Mode (part set) 574 000 Group by-pass 401 001 User 1 through to 024 User 24 Duress Alarm 121 101 Duress at Keypad #1 102 Duress at Keypad #2 through to 108 Duress at keypad #8

PROGRAMMING USER CODES P1E User Code #1 (Master Code) if deleted code is reset to 987654 - Default 123 Page 18 P2E User Code #2 Page 18 P3E User Code #3 Page 18 P4E User Code #4 Page 18 P5E User Code #5 Page 18 P6E User Code #6 Page 18 P7E User Code #7 Page 18 P8E User Code #8 Page 18 P9E User Code #9 Page 18 P10E User Code #10 Page 18 P11E User Code #11 Page 18 P12E User Code #12 Page 18 P13E User Code #13 Page 18 P14E User Code #14 Page 18 P15E User Code #15 Page 18 P16E User Code #16 Page 18 P17E User Code #17 Page 18 P18E User Code #18 Page 18 P19E User Code #19 Page 18 P20E User Code #20 Page 18 P21E User Code #21 Page 18 P22E User Code #22 Page 18 P23E User Code #23 Page 18 P24E User Code #24 Page 18 INSTALLER PROGRAM MODE PROGRAMMING USER CODE PERMISSIONS P25E Standard Access Permissions for user #1 - Default 1-8 P25E-48E OPTIONS Page 19 P26E Standard Access Permissions for user #2 - Default 1-8 1 = Area "A" Page 19 P27E Standard Access Permissions for user #3 - Default 1-8 2 = Area "B" Page 19 P28E Standard Access Permissions for user #4 - Default 1-8 3 = Area "C" Page 19 P29E Standard Access Permissions for user #5 - Default 1-8 4 = Code can arm Page 19 P30E Standard Access Permissions for user #6 - Default 1-8 5 = Code can disarm Page 19 P31E Standard Access Permissions for user #7 - Default 1-8 6 = Code can monitor Page 19 P32E Standard Access Permissions for user #8 - Default 1-8 7 = Code can un-monitor Page 19 P33E Standard Access Permissions for user #9 - Default 1-8 8 = Code can operate Control Page 19 P34E Standard Access Permissions for user #10 - Default 1-8 Page 19 P35E Standard Access Permissions for user #11 - Default 1-8 Page 19 P36E Standard Access Permissions for user #12 - Default 1-8 Page 19 P37E Standard Access Permissions for user #13 - Default 1-8 Page 19 P38E Standard Access Permissions for user #14 - Default 1-8 Page 19 P39E Standard Access Permissions for user #15 - Default 1-8 Page 19 P40E Standard Access Permissions for user #16 - Default 1-8 Page 19 P41E Standard Access Permissions for user #17 - Default 1-8 Page 19 P42E Standard Access Permissions for user #18 - Default 1-8 Page 19 P43E Standard Access Permissions for user #19 - Default 1-8 Page 19 P44E Standard Access Permissions for user #20 - Default 1-8 Page 19 P45E Standard Access Permissions for user #21 - Default 1-8 Page 19 P46E Standard Access Permissions for user #22 - Default 1-8 Page 19 P47E Standard Access Permissions for user #23 - Default 1-8 Page 19 P48E Standard Access Permissions for user #24 - Default 1-8 Page 19 PROGRAMMING EXTENDED USER CODE PERMISSIONS P49E Extended Access Permissions for user #1 - Default 1238 P49E-P72E OPTIONS Page 19

P51E Extended Access Permissions for user #3 - Default 3 2 = Can change phone numbers Page 19 P52E Extended Access Permissions for user #4 - Default 3 3 = Can change real time clock Page 19 P53E Extended Access Permissions for user #5 - Default 3 4 = Can start a printout Page 19 P54E Extended Access Permissions for user #6 - Default 3 5 = Can answer call for u/d load Page 19 P55E Extended Access Permissions for user #7 - Default 3 6 = Can change their code only Page 19 P56E Extended Access Permissions for user #8 - Default 3 7 = Can change all codes Page 19 P57E Extended Access Permissions for user #9 - Default 3 8 = Allows access to installer Page 19 P58E Extended Access Permissions for user #10 - Default 3 mode via client mode. Page 19 P59E Extended Access Permissions for user #11 - Default 3 Page 19 P60E Extended Access Permissions for user #12 - Default 3 Page 19 P61E Extended Access Permissions for user #13 - Default 3 Page 19 P62E Extended Access Permissions for user #14 - Default 3 Page 19 P63E Extended Access Permissions for user #15 - Default 3 Page 19 P64E Extended Access Permissions for user #16 - Default 3 Page 19 P65E Extended Access Permissions for user #17 - Default 3 Page 19 P66E Extended Access Permissions for user #18 - Default 3 Page 19 P67E Extended Access Permissions for user #19 - Default 3 Page 19 P68E Extended Access Permissions for user #20 - Default 3 Page 19 P69E Extended Access Permissions for user #21 - Default 3 Page 19 P70E Extended Access Permissions for user #22 - Default 3 Page 19 P71E Extended Access Permissions for user #23 - Default 3 Page 19 P72E Extended Access Permissions for user #24 - Default 3 Page 19 PROGRAMMIMG USER CODE TIME CONTROL P73E Access Time Zones for user #1 - Default 0 (24 Hr 7 Days) Page 19 P74E Access Time Zones for user #2 - Default 0 (24 Hr 7 Days) Page 19 P75E Access Time Zones for user #3 - Default 0 (24 Hr 7 Days) Page 19 P76E Access Time Zones for user #4 - Default 0 (24 Hr 7 Days) Page 19 P77E Access Time Zones for user #5 - Default 0 (24 Hr 7 Days) Page 19 P78E Access Time Zones for user #6 - Default 0 (24 Hr 7 Days) Page 19 P79E Access Time Zones for user #7 - Default 0 (24 Hr 7 Days) Page 19 P80E Access Time Zones for user #8 - Default 0 (24 Hr 7 Days) Page 19 P81E Access Time Zones for user #9 - Default 0 (24 Hr 7 Days) Page 19 P82E Access Time Zones for user #10 - Default 0 (24 Hr 7 Days) Page 19 P83E Access Time Zones for user #11 - Default 0 (24 Hr 7 Days) Page 19 P84E Access Time Zones for user #12 - Default 0 (24 Hr 7 Days) Page 19 P85E Access Time Zones for user #13 - Default 0 (24 Hr 7 Days) Page 19 P86E Access Time Zones for user #14 - Default 0 (24 Hr 7 Days) Page 19 P87E Access Time Zones for user #15 - Default 0 (24 Hr 7 Days) Page 19 P88E Access Time Zones for user #16 - Default 0 (24 Hr 7 Days) Page 19 P89E Access Time Zones for user #17 - Default 0 (24 Hr 7 Days) Page 19 P90E Access Time Zones for user #18 - Default 0 (24 Hr 7 Days) Page 19 P91E Access Time Zones for user #19 - Default 0 (24 Hr 7 Days) Page 19 P92E Access Time Zones for user #20 - Default 0 (24 Hr 7 Days) Page 19 P93E Access Time Zones for user #21 - Default 0 (24 Hr 7 Days) Page 19 P94E Access Time Zones for user #22 - Default 0 (24 Hr 7 Days) Page 19 P95E Access Time Zones for user #23 - Default 0 (24 Hr 7 Days) Page 19 P96E Access Time Zones for user #24 - Default 0 (24 Hr 7 Days) Page 19 P99E Installer Code - Default 000000 - must be more than 3 digits long Page 19 P100E Option 8.Led 8 on means installer code can go directly into installer program mode. Page 19 PROGRAMMING OUTPUT OPTIONS P101E-P108E OPTIONS P101E Output #1 Primary options - Default none 1 = Invert Page 20 P102E Output #2 Primary options - Default none 2 = Flashing Page 20 P103E Output #3 Primary options - Default none 3 = Single pulse Page 20

P105E Output #5 Primary options - Default none 5 = DTMF cmd remote control Page 20 P106E Output #6 Primary options - Default none 6 = Local command control Page 20 P107E Output #7 Primary options - Default none 7 = Day zone linked to pulse timer Page 20 P108E Output #8 Primary options - Default none 8 = Spare Page 20 P111E Output #1 Expanded options - Default 1-5 P111E-P118E OPTIONS Page 20 P112E Output #2 Expanded options - Default 1-5 1 = Keypad panic to output Page 20 P113E Output #3 Expanded options - Default 1-5 2 = Keypad tamper to output Page 20 P114E Output #4 Expanded options - Default 1-5 3 = Zone tampers to output Page 20 P115E Output #5 Expanded options - Default 1-5 4 = Cabinet tamper to output Page 20 P116E Output #6 Expanded options - Default 1-5 5 = Radio key panic to output Page 20 P117E Output #7 Expanded options - Default 1-5 6 = Mains fail to output Page 20 P118E Output #8 Expanded options - Default 1-5 7 = Battery low to output Page 20 8 = Phone Line failure P121E Output #1 Automatic on / off time zones - Default 0 (never) Page 22 P122E Output #2 Automatic on / off time zones - Default 0 (never) Page 22 P123E Output #3 Automatic on / off time zones - Default 0 (never) Page 22 P124E Output #4 Automatic on / off time zones - Default 0 (never) Page 22 P125E Output #5 Automatic on / off time zones - Default 0 (never) Page 22 P126E Output #6 Automatic on / off time zones - Default 0 (never) Page 22 P127E Output #7 Automatic on / off time zones - Default 0 (never) Page 22 P128E Output #8 Automatic on / off time zones - Default 0 (never) Page 22 P131E Output #1 Enable time zones - Default 0 (always) Page 22 P132E Output #2 Enable time zones - Default 0 (always) Page 22 P133E Output #3 Enable time zones - Default 0 (always) Page 22 P134E Output #4 Enable time zones - Default 0 (always) Page 22 P135E Output #5 Enable time zones - Default 0 (always) Page 22 P136E Output #6 Enable time zones - Default 0 (always) Page 22 P137E Output #7 Enable time zones - Default 0 (always) Page 22 P138E Output #8 Enable time zones - Default 0 (always) Page 22 PROGRAMMING KEYPAD OPTIONS P140E Keypads assigned to Area "A" - Default 1-8 Page 22 P141E Keypads assigned to Area "B" - Default none Page 22 P142E Keypads assigned to Area "C" - Default none Page 22 P143E Keypads with permission to set - Default 1-8 Page 22 P144E Keypads with permission to Monitor - Default 1-8 Page 22 P145E Keypads with permission to use control function - Default 1-8 Page 22 P146E Keypads with permission to exclude zones - Default 1-8 Page 22 P147E Keypads with listen in feature enabled - Default 1 Page 22 P148E Keypads with permission for Client programming mode - Default 1-8 Page 22 P149E Keypads with permission for Installer programming mode - Default 1-8 Page 22 P152E Keypads with facility to turn off LED's after exit delay - Default none Page 22 P153E Keypads with buzzer mapped to keypad tamper - Default 1-8 Page 22 P154E Keypads with buzzer mapped to zone tamper - Default 1-8 Page 22 P155E Keypads with buzzer mapped to cabinet tamper - Default 1-8 Page 22 P156E Keypads with Panic Button enabled - Default 1-8 Page 22 P157E Keypads with buzzer mapped to keypad panic - Default 1-8 Page 22 P158E Keypads with buzzer mapped to line failure - Default none PROGRAMMING PARTITION 'A' PARAMETERS P170E Time Zones used for Area "A" auto arming /disarming- Default 0 Page 23 PARTITION 'A' PRIMARY OUTPUT OPTIONS P171E-P178E OPTIONS P171E Area "A" primary options for output #1 - Default 1 1 = Standard zone activation's Page 24

P173E Area "A" primary options for output #3 - Default 1 3 = Monitor Mode activation's Page 24 P174E Area "A" primary options for output #4 - Default 1 4 = Radio key chirps Page 24 P175E Area "A" primary options for output #5 - Default 1 5 = All zones sealed (ready) Page 24 P176E Area "A" primary options for output #6 - Default 1 6 = 2 sec pulse on arm / disarm Page 24 P177E Area "A" primary options for output #7 - Default 1 7 = Intelligent smoke reset pulse Page 24 P178E Area "A" primary options for output #8 - Default 1 8 = Day zone activation's Page 24 PARTITION 'A' SPECIFIC OUTPUT OPTIONS P181E-P188E OPTIONS P181E Area "A" specific options for output #1 - Default 0 1 = Any exclude Page 25 P182E Area "A" specific options for output #2 - Default 0 2 = Auto exclude warning Page 25 P183E Area "A" specific options for output #3 - Default 0 3 = Entry beeps Page 25 P184E Area "A" specific options for output #4 - Default 0 4 = Exit beeps Page 25 P185E Area "A" specific options for output #5 - Default 0 5 = Control Page 25 P186E Area "A" specific options for output #6 - Default 0 6 = Set/unset Page 25 P187E Area "A" specific options for output #7 - Default 0 7 = Monitor set/unset Page 25 P188E Area "A" specific options for output #8 - Default 0 8 = Keypad duress Page 25 PARTITION 'A' KEYPAD OPTIONS P189E Arm key can disarm during exit - Default 1-8 Page 25 P190E Monitor can disarm during mon. - Default l-8 Page 25 P191E Day mode beeps to keypads - Default 1-8 Page 25 P192E Zone set alarm to keypads - Default 1-8 Page 26 P193E Zone monitor alarms to keypads - Default 1-8 Page 26 P194E 24 Hour alarms to keypads - Default 1-8 Page 26 P195E Exit beeps - Default 1-8 Page 26 P196E Entry beeps - Default 1-8 Page 26 PROGRAMMING DURESS DIGIT FOR PARTITION 'A' P197E Duress digit - Default 0 Page 26 PARTITION 'A' MISC OPTIONS P198E Misc partition options 1 - Default 0 1 = Spare Page 27 2 = 'Arm' required before code 3 = 'Monitor' required before code 4 = Code required to arm 5 = Code required for control 6 = Control toggles 7 = Momentary control 8 = Control disables day zones P199E Misc partition options 2 - Default 3,4,6 1 = Keyswitch enabled Page 28 2 = Use 2nd Keyswitch 3 = Keyswitch ARM's/MONITOR 4 = Pendant chirps when armed 5 = Pendant chirps when monitoring 6 = 2 sec pulse at set 7 = 2 sec pulse at unset 8 = Access control even when armed P180E PARTITION "A" TIME AND DELAY OPTIONS Page 26 1 = set partition When Time Zone Ends 2 = Unset Partition When Time Zone Starts 3 = Disable Monitor Mode Exit Delay 4 = Disable Set Mode Exit Delay 5 = Disable Monitor Mode Entry Delay 6 = Disable Set Mode Entry Delay 7 = Spare 8 = Disable zone tampers during exit delay

P270E Time zones used for Area "B" auto arming/disarming - Default 0 Page 24-28 PARTITION 'B' PRIMARY OUTPUT OPTIONS P271E-P278E OPTIONS P271E Area "B" primary options for output #1 - Default 1 1 = Standard zone activation's Page 24-28 P272E Area "B" primary options for output #2 - Default 1 & 3 2 = 24Hr activation's Page 24-28 P273E Area "B" primary options for output #3 - Default 1 3 = Monitor Mode activation's Page 24-28 P274E Area "B" primary options for output #4 - Default 1 4 = Radio key chirps Page 24-28 P275E Area "B" primary options for output #5 - Default 1 5 = All zones sealed (Ready) Page 24-28 P276E Area "B" primary options for output #6 - Default 1 6 = 2 sec pulse arm/disarm Page 24-28 P277E Area "B" primary options for output #7 - Default 1 7 = Intelligent smoke reset pulse Page 24-28 P278E Area "B" primary options for output #8 - Default 1 8 = Day zone activation's Page 24-28 PARTITION 'B' SPECIFIC OUTPUT OPTIONS P281E-P288E OPTIONS P281E Area "B" specific options for output #1 - Default 0 1 =Any exclude Page 24-28 P282E Area "B" specific options for output #2 - Default 0 2 = Auto exclude warning Page 24-28 P283E Area "B" specific options for output #3 - Default 0 3 = Entry beeps Page 24-28 P284E Area "B" specific options for output #4 - Default 0 4 = Exit beeps Page 24-28 P285E Area "B" specific options for output #5 - Default 0 5 = Control Page 24-28 P286E Area "B" specific options for output #6 - Default 0 6 = Set/unset Page 24-28 P287E Area "B" specific options for output #7 - Default 0 7 = Monitor set/unset Page 24-28 P288E Area "B" specific options for output #8 - Default 0 8 = Keypad duress Page 24-28 PARTITION 'B' KEYPAD OPTIONS P289E Arm key can disarm during exit - Default 1-8 Page 24-28 P290E Monitor can disarm during mon. - Default 1-8 Page 24-28 P291E Day mode beeps to keypads - Default 1-8 Page 24-28 P292E Zone set alarms to keypads - Default 1-8 Page 24-28 P293E Zone monitor alarms to keypads - Default 1-8 Page 24-28 P294E 24Hr alarms to keypads - Default 1-8 Page 24-28 P295E Exit beeps - Default 1-8 Page 24-28 P296E Entry beeps - Default 1-8 Page 24-28 PROGRAMMING DURESS DIGIT FOR PARTITION "B" P297E Duress digit - Default 0 PARTITION 'B' MISC OPTIONS P298E Misc partition options 1 - Default 0 1 = Spare Page 24-28 2 = Arm required before code 3 = Monitor required before code 4 = Code required to arm 5 = Code required for control 6 = Control toggles 7 = Momentary control 8 = Control disables day zones Page 24-28 P299E Misc partitions options 2 - Default 3,4,6 1 = Keyswitch enabled Page 24-28 2 = Use 2nd Keyswitch 3 = Keyswitch ARM's/MONITOR 4 = Pendant chirps when armed 5 = Pendant chirps when monitoring 6 = 2 sec pulse at set 7 = 2 sec pulse at unset 8 = Access control even when armed P280E PARTITION "B" TIME AND DELAY OPTIONS 1 = set partition When Time Zone Ends

3 = Disable Monitor Mode Exit Delay 4 = Disable Set Mode Exit Delay 5 = Disable Monitor Mode Entry Delay 6 = Disable Set Mode Entry Delay 7 = Spare 8 = Disable zone tampers during exit delay PROGRAMMING PARTITION 'C' PARAMETERS P370E Time zones used for Area "C" auto-arming/disarming - Default 0 Page 24- 28 PARTITION 'C' PRIMARY OUTPUT OPTIONS P371E-P378E OPTIONS P371E Area 'C' primary options for output #1- Default 1 1 = Standard zone activation's Page 24- 28 P372E Area 'C' primary options for output #2 - Default 1 & 3 2 = 24Hr activation's Page 24- 28 P373E Area "C" primary options for output #3 - Default 1 3 = Monitor Mode activation's Page 24- 28 P374E Area "C" primary options for output #4 - Default 1 4 = Radio key chirps Page 24- 28 P375E Area "C" primary options for output #5 - Default 1 5 = All zones sealed (ready) Page 24- 28 P376E Area "C" primary options for output #6 - Default 1 6 = 2 sec pulse on arm/disarm Page 24- 28 P377E Area "C" primary options for output #7 - Default 1 7 = Intelligent smoke reset pulse Page 24- 28 P378E Area "C" primary options for output #8 - Default 1 8 = Day zone activation's Page 24- 28 PARTITION 'C' SPECIFIC OUTPUT OPTIONS P381E-P388E OPTIONS P381E Area "C" specific options for output #1 - Default 0 1 = Any exclude Page 24- 28 P382E Area "C" specific options for output #2 - Default 0 2 = Auto exclude warn Page 24- 28 P383E Area "C"' specific options for output #3 - Default 0 3 = Entry beeps Page 24- 28 P384E Area "C" specific options for output #4 - Default 0 4 = Exit Beeps Page 24- 28 P385E Area "C" specific options for output #5 - Default 0 5 = Control Page 24- 28 P386E Area "C" specific options for output #6 - Default 0 6 = Set/unset Page 24- 28 P387E Area "C" specific options for output #7 - Default 0 7 = Monitor set/unset Page 24- 28 P388E Area "C" specific options for output #8 - Default 0 8 = Kbd duress Page 24- 28 PARTITION "C" KEYPAD OPTIONS P389E Arm key can disarm during exit - Default 1-8 Page 24- 28 P390E Monitor can disarm during mon. - Default 1-8 Page 24- 28 P391E Day mode beeps to keypads - Default 1-8 Page 24- 28 P392E Zone set alarms to keypads - Default 1-8 Page 24- 28 P393E Zone monitor alarms to keypads - Default 1-8 Page 24- 28

P395E Exit beeps - Default 1-8 Page 24-28 P396E Entry beeps - default 1-8 Page 24-28 PROGRAMMING DURESS DIGIT FOR PARTITION 'C' P397E Duress digit - Default 0 Page 24-28 PARTITION 'C' MISC OPTIONS P398E Misc partition options 1 - Default 0 1 = Spare Page 24-28 2 = 'Arm' required before code 3 = 'Monitor' required before code 4 = Code required to arm 5 = Code required for control 6 = Control toggles 7 = Momentary control 8 = Control disables day zones P399E Misc partition options 2 - Default 3,4,6 1 = Keyswitch enabled Page 24-28 2 = Use 2nd Keyswitch 3 = Keyswitch ARM's/MONITOR 4 = Pendant chirps when armed 5 = Pendant chirps when monitoring 6 = 2 sec pulse at set 7 = 2 sec pulse at unset 8 = Access control even when armed P380E PARTITION "C" TIME AND DELAY OPTIONS (Default 0) 1 = set partition When Time Zone Ends 2 = Unset Partition When Time Zone Starts 3 = Disable Monitor Mode Exit Delay 4 = Disable Set Mode Exit Delay 5 = Disable Monitor Mode Entry Delay 6 = Disable Set Mode Entry Delay 7 = Spare 8 = Disable zone tampers during exit delay MISCELLANEOUS SYSTEM OPTIONS P201E Options - Default 3,4,5,7,8 1 = Mains input AC or DC Page 29 2 = Ignore Mains fail 3 = Low Keyswitch is momentary or latching 4 = High Keyswitch is momentary or latching 5 = Cabinet tamper is loop or end-of-line 6 = Installer lockout 7 = Area "C" is zones shared with Area A & B 8 = Local serial port is 9600bps or 2400bps P204E Spare Page 29 P205E Spare Page 29 P206E Spare Page 29 SINGLE OR DUAL ZONE INPUT (8-or 16 ZONES) P300E Single or dual zone input - Default-All Off(zones 1-8 only) Page 30 VIBRATION SENSOR ZONE ASSIGNMENTS

P302E Zone 2 vibration sensitivity - Default 0 Sensitivity 1-8 Page 30 P303E Zone 3 vibration sensitivity - Default 0 1 = High sensitivity Page 30 P304E Zone 4 vibration sensitivity - Default 0 8 = Low sensitivity Page 30 P305E Zone 5 vibration sensitivity - Default 0 Page 30 P306E Zone 6 vibration sensitivity - Default 0 Page 30 P307E Zone 7 vibration sensitivity - Default 0 Page 30 P308E Zone 8 vibration sensitivity - Default 0 Page 30 P161E Zone 9 vibration sensitivity - Default 0 Page 30 P162E Zone 10 vibration sensitivity - Default 0 Page 30 P163E Zone11 vibration sensitivity - Default 0 Page 30 P164E Zone 12 vibration sensitivity - Default 0 Page 30 P165E Zone 13 vibration sensitivity - Default 0 Page 30 P166E Zone 14 vibration sensitivity - Default 0 Page 30 P167E Zone 15 vibration sensitivity - Default 0 Page 30 P168E Zone 16 vibration sensitivity - Default 0 Page 30 LOW ZONE ASSIGNMENTS (ZONES 1-8) P331E Zone is a normally open/closed output - Default N/C 0ff = N/C On = N/O Page 30 P332E Zone is a radio detector - Default 0ff Page 30 P333E Zone is in Area "A" - Default all ) Page 30 P334E Zone is in Area "B" - Default none ) If zone is in both it is then a partition "C" zone Page 30 P335E Zone is isolatable - Default all Page 30 P336E Zone is a handover - Default 2 Page 31 P337E Two trigger zones -Default none Page 31 P338E Zone is 24Hr - Default none Page 31 P339E Monitor mode zones - Default zones 1-4 Page 31 P340E Day zones - Default none Page 31 P341E Siren lockout zones - Default none Page 31 P342E Auto exclude zones - Default all Page 31 P343E Access control door position input - Default none Page 31 P344E Access control request to exit input - Default none Page 31 P345E Continuous day zone - Default none Page 31 P346E Zones 1-8 will report multiple activations Default on HIGH ZONE ASSIGNMENTS (ZONES 9-16) P351E Zone is a normally open/closed output - Default N/C 0ff = N/C On = N/O Page 31 P352E Zone is a radio detector - Default 0ff Page 31 P353E Zone is in Area "A" - Default all ) Page 31 P354E Zone is in Area "B" - Default none ) If zone is in both it is then a partition "C" zone Page 31 P355E Zone is isolatable - Default all Page 31 P356E Zone is a handover - Default none Page 31 P357E Two trigger zones -Default none Page 31 P358E Zone is 24Hr - Default none Page 31 P359E Monitor mode zones - Default zones 1-4 Page 31 P360E Day zones - Default none Page 31 P361E Siren lockout zones - Default none Page 31 P362E Auto exclude zones - Default all Page 31 P363E Access control door position input - Default none Page 31 P364E Access control request to exit input - Default none Page 31 P365E Exclusive day zone - Default none Page 31 P366E Zones 9-16 will report multiple activations-Default on SYSTEM DELAYS & TIMERS P401E Zone 1 entry delay - Default 20 sec Delay timer values Page 32 P402E Zone 2 entry delay - Default 20 sec 0 = instant, no delay Page 32 P403E Zone 3 entry delay - Default 0 1-999 = 1 -999 seconds Page 32 P404E Zone 4 entry delay - Default 0 Page 32 P405E Zone 5 entry delay - Default 0 Page 32 P406E Zone 6 entry delay - Default 0 Page 32 P407E Zone 7 entry delay - Default 0 Page 32 P408E Zone 8 entry delay - Default 0 Page 32 P409E Zone 9 entry delay - Default 0 Page 32 P410E Zone 10 entry delay - Default 0 Page 32 P411E Zone 11 entry delay - Default 0 Page 32 P412E Zone 12 entry delay - Default 0 Page 32

P414E Zone 14 entry delay - Default 0 Page 32 P415E Zone 15 entry delay - Default 0 Page 32 P416E Zone 16 entry delay - Default 0 Page 32 P417E Area "A" exit delay -Default = 60 sec Page 32 P418E Area "B: exit delay - Default = 60 sec Page 32 P419E Area "C" exit delay - Default = 60 sec Page 32 P421E Output #1 reset time - Default 600 sec Reset time values Page 32 P422E Output #2 reset time - Default 600 sec 0 = latching Page 32 P423E Output #3 reset time - Default 600 sec 1-999 = 1 to 999 seconds Page 32 P424E Output #4 reset time - Default 600 sec Page 32 P425E Output #5 reset time - Default 0 sec Page 32 P426E Output #6 reset time - Default 0 sec Page 32 P427E Output #7 reset time - Default 0 sec Page 32 P428E Output #8 reset time - Default 0 sec Page 32 P431E Output #1 delay on timer - Default 0 Delay time values Page 32 P432E Output #2 delay on timer - Default 0 0 = no delay Page 32 P433E Output #3 delay on timer - Default 0 1 - 999 = 1 to 999 seconds Page 32 P434E Output #4 delay on timer - Default 0 Page 32 P435E Output #4 delay on timer - Default 0 Page 32 P436E Output #5 delay on timer - Default 0 Page 32 P437E Output #6 delay on timer - Default 0 Page 32 P438E Output #7 delay on timer - Default 0 Page 32 P441E Output #1 pulse time - Default 0 Pulse time values Page 32 P442E Output #2 pulse time - Default 0 1-999 (min of 1) Page 32 P443E Output #3 pulse time - Default 0 1 to 999 in 1/10 secs Page 32 P444E Output #4 pulse time - Default 0 e.g. 1 = 0.1 second Page 32 P445E Output #5 pulse time - Default 0 10 = 1 second Page 32 P446E Output #6 pulse time - Default 0 Page 32 P447E Output #7 pulse time - Default 0 Page 32 P448E Output #8 pulse time - Default 0 Page 32 P450E Report delay on zone alarms - 1-99 seconds - Default 0 Page 33 P451E Area "A" two trigger time period - Default 60 sec Page 32 P452E Area "B" two trigger time period - Default 60 sec Page 32 P453E Area "C" two trigger time period - Default 60 sec Page 32 P454E Area "A" door open too long timer (DOTL) - Default 10 sec Page 33 P455E Area "B" door open too long timer (DOTL) - Default 10 sec Page 33 P456E Area "C" door open too long timer (DOTL) - Default 10 sec Page 33 P457E Area "A" day zone keypad buzzer duration - Default 2 sec Page 32 P458E Area "B" day zone keypad buzzer duration - Default 2 sec Page 32 P459E Area "C" day zone keypad buzzer duration - Default 2 sec Page 32 ENROLLING RADIO DETECTORS (ZONES 1-16) - (MUST ALSO PROGRAM P332E & P352E ADDRESSES) P501E Enrol Radio Detector Zone 1 Page 34 P502E Enrol Radio Detector Zone 2 Page 34 P503E Enrol Radio Detector Zone 3 Page 34 P504E Enrol Radio Detector Zone 4 Page 34 P505E Enrol Radio Detector Zone 5 Page 34 P506E Enrol Radio Detector Zone 6 Page 34 P507E Enrol Radio Detector Zone 7 Page 34 P508E Enrol Radio Detector Zone 8 Page 34 P509E Enrol Radio Detector Zone 9 Page 34 P510E Enrol Radio Detector Zone 10 Page 34 P511E Enrol Radio Detector Zone 11 Page 34 P512E Enrol Radio Detector Zone 12 Page 34 P513E Enrol Radio Detector Zone 13 Page 34 P514E Enrol Radio Detector Zone 14 Page 34 P515E Enrol Radio Detector Zone 15 Page 34 P516E Enrol Radio Detector Zone 16 Page 34

P521E - P536E OPTIONS P521E Radio Detector zone #1 options - Default 1 1 = Ness battery fail Page 34 P522E Radio Detector zone #2 options - Default 1 2 = Ness radio reed switch Page 34 P523E Radio Detector zone #3 options - Default 1 3 = Crow battery low Page 34 P524E Radio Detector zone #4 options - Default 1 4 = Visonic PIR batt low/tamper Page 34 P525E Radio Detector zone #5 options - Default 1 5 = EL PIR batt low/tamper Page 34 P526E Radio Detector zone #6 options - Default 1 6 = Spare Page 34 P527E Radio Detector zone #7 options - Default 1 7 = Spare Page 34 P528E Radio detector zone #8 options - Default 1 8 = Spare Page 34 P529E Radio Detector zone #9 options - Default 1 Page 34 P530E Radio Detector zone #10 options - Default 1 Page 34 P531E Radio Detector zone #11 options - Default 1 Page 34 P532E Radio Detector zone #12 options - Default 1 Page 34 P533E Radio Detector zone #13 options - Default 1 Page 34 P534E Radio detector zone #14 options - Default 1 Page 34 P535E Radio Detector zone #15 options - Default 1 Page 34 P536E Radio Detector zone #16 options - Default 1 Page 34 ENROLLING RADIO KEYS P541E Enrol Radio user #1 Page 35 P542E Enrol Radio user #2 Page 35 P543E Enrol Radio user #3 Page 35 P544E Enrol Radio user #4 Page 35 P545E Enrol Radio user # 5 Page 35 P546E Enrol Radio user #6 Page 35 P547E Enrol Radio user #7 Page 35 P548E Enrol Radio user #8 Page 35 P549E Enrol radio user #9 Page 35 P550E Enrol Radio user #10 Page 35 P551E Enrol Radio user #11 Page 35 P552E Enrol Radio user #12 Page 35 P553E Enrol Radio user #13 Page 35 P554E Enrol Radio user #14 Page 35 P555E Enrol Radio user #15 Page 35 P556E Enrol Radio user #16 Page 35 RADIO KEY OPTIONS 1ST SET P561E - 576E OPTIONS P561E Radio user #1 options - Default 1,4,5 1 = Area "A" permission Page 35 P562E Radio user #2 options - Default 1,4,5 2 = Area "B" permission Page 35 P563E Radio user #3 options - Default 1,4,5 3 = Area "C" permission Page 35 P564E Radio user #4 options - Default 1,4,5 4 = User can arm Page 35 P565E Radio user #5 options - Default 1,4,5 5 = User can disarm Page 35 P566E Radio user #6 options - Default 1,4,5 6 = User can monitor Page 35 P567E Radio user #7 options - Default 1,4,5 7 = User can un-monitor Page 35 P568E Radio user #8 options - Default 1,4,5 8 = User disabled if in alarm Page 35 P569E Radio user #9 options - Default 1,4,5 Page 35 P570E Radio user #10 options - Default 1,4,5 Page 35 P571E Radio user #11 options - Default 1,4,5 Page 35 P572E Radio user #12 options - Default 1,4,5 Page 35 P573E Radio user #13 options - Default 1,4,5 Page 35 P574E Radio user #14 options - Default 1,4,5 Page 35 P575E Radio user #15 options - Default 1,4,5 Page 35 P576E Radio user #16 options - Default 1,4,5 Page 35

P581E Radio user #1 options - Default 0 P581E-P596E OPTIONS Page 36 P582E Radio user #2 options - Default 0 1 = User turns control on Page 36 P583E Radio user #3 options - Default 0 2 = User turns control off Page 36 P584E Radio user #4 options - Default 0 3 = User turns output on Page 36 P585E Radio user #5 options - Default 0 4 = User turns output off Page 36 P586E Radio user #6 options - Default 0 5 = Spare Page 36 P587E Radio user #7 options - Default 0 6 = User causes immediate panic Page 36 P588E Radio user #8 options - Default 0 7 = User causes delayed panic Page 36 P589E Radio user #9 options - Default 0 8 = Ness 24Hr battery low check Page 36 P590E Radio user #10 options - Default 0 Page 36 P591E Radio user #11 options - Default 0 Page 36 P592E Radio user #12 options - Default 0 Page 36 P593E Radio user #13 options - Default 0 Page 36 P594E Radio user #14 options - Default 0 Page 36 P595E Radio user #15 options - Default 0 Page 36 P596E Radio user #16 options - Default 0 Page 36 MAPPING RADIO USERS TO OUTPUTS P601E radio user #1 to output 1-8 - Default 0 Page 37 P602E radio user #2 to output 1-8 - Default 0 Page 37 P603E radio user #3 to output 1-8 - Default 0 Page 37 P604E radio user #4 to output 1-8 - Default 0 Page 37 P605E radio user #5 to output 1-8 - Default 0 Page 37 P606E radio user #6 to output 1-8 - Default 0 Page 37 P607E radio user #7 to output 1-8 - Default 0 Page 37 P608E radio user #8 to output 1-8 - Default 0 Page 37 P609E radio user #9 to output 1-8 - Default 0 Page 37 P610E Radio user #10 to output 1-8 - Default 0 Page 37 P611E Radio user #11 to output 1-8 - Default 0 Page 37 P612E Radio user #12 to output 1-8 - Default 0 Page 37 P613E Radio user #13 to output 1-8 - Default 0 Page 37 P614E Radio user #14 to output 1-8 - Default 0 Page 37 P615E Radio user #15 to output 1-8 - Default 0 Page 37 P616E Radio user #16 to output 1-8 - Default 0 Page 37 DEFINING TIME ZONES P681E Time Zone 1 day of the week Default 0 TIME ZONE PROGRAMMING Page 37 P682E Time Zone 1 start time - Default 0 DAYS 1 - 7 Page 37 P683E Time Zone 1 finish time - Default 0 1 = Sunday Page 37 P684E Time Zone 2 day of the week - Default 0 2 = Monday Page 37 P685E Time Zone 2 start time - Default 0 3 = Tuesday Page 37 P686E Time Zone 2 finish time - Default 0 4 = Wednesday Page 37 P687E Time Zone 3 day of the week - Default 0 5 = Thursday Page 37 P688E Time Zone 3 start time - Default 0 6 = Friday Page 37 P689E Time Zone 3 finish time - Default 0 7 = Saturday Page 37 P690E Time Zone 4 day of the week - Default 0 8 = Invert time zone Page 37 P691E Time Zone 4 start time - Default 0 Times = 0000-2359 Page 37 P692E Time Zone 4 finish time - Default 0 Page 37 P693E Time Zone 5 day of the week - Default 0 Page 37 P694E Time Zone 5 start time - Default 0 Page 37 P695E Time Zone 5 finish time - Default 0 Page 37 P696E Time Zone 6 day of the week - Default 0 Page 37 P697E Time Zone 6 start time - Default 0 Page 37 P698E Time Zone 6 finish time - Default 0 Page 37 P699E Time Zone 7 day of the week - Default 0 Page 37 P700E Time Zone 7 start time - Default 0 Page 37 P701E Time Zone 7 finish time - Default 0 Page 37 P702E Time Zone 8 day of the week - Default 0 Page 37

P704E Time Zone 8 finish time - Default 0 Page 37 PROGRAMMING DAYLIGHT SAVING ADJUSTMENTS P712E Daylight saving start Sunday - Default 1 Page 38 P713E Daylight saving start month - Default 10 Page 38 P714E Daylight saving start hour - Default 2 Page 38 P715E Daylight saving end Sunday - Default 3 Page 38 P716E Daylight saving end month - Default 3 Page 38 P717E Daylight saving end hour - Default 3 Page 38 ZONE RESPONSE TIME SETTINGS P709E Zone response settings default = 6 (value 1-32E) Page 38 DYNAMIC DATA P720E Time zones active at this time (Time zones 1 - 8) Page 38 P721E Misc system flags 1 = Spare 5=Spare Page 38 2 = Spare 6=Spare 3 = Spare 7=Spare 4 = Spare 8=Daylight saving active P740E Clear all output parameters (outputs 1 - 8) Page 40 P723E Display keyboard address Page 39 P724E Display partitions assigned to this keypad (1=A, 2=B, 3=C) Page 39 P725E Display software version Page 39 PRINTING EVENTS P726E Start event printing Page 39 SETTING THE REAL TIME CLOCK P730E Set day of the week (1 -7 where 1 = Sunday) Page 40 P731E Set time (HHMM) Page 40 P732E Set day of the month (1 - 31) Page 40 P733E Set month (1 - 12) Page 40 P734E Set year Page 40 EEPROM UP/DOWNLOAD P736E Write to Eeprom board on serial port. Page 40 P738E Copy from Eeprom board on serial port to panel. Page 40 WALK TEST MODE P735E Toggle walktest mode ON/OFF Page 40 RESET DEFAULTS P741E Reset user codes Page 40 P742E Reset communicator parameters Page 40 P743E Reset radio parameters Page 40 P744E Reset all other parameters Page 40 P745E Clear event memory Page 40 MANUFACTURE DATE P747E Manufacturing software program day P748E Manufacturing software program month P749E Manufacturing software program year COMMAND CONTROL PROGRAMMING Page 41 COMMAND CONTROL OPERATION Page 43 COMMUNICATOR INTRODUCTION Page 44 COMMUNICATOR REPORTING FORMATS Page 45

P211E Reporting Scenario #1 options Page 47 P212E Reporting Scenario #2 options Page 47 P213E Reporting Scenario #3 options Page 47 P214E Reporting Scenario #4 options Page 47 MAXIMUM DIALLING ATTEMPTS PER SCENARIO P215E Max Dial Attempts for Scenario 1-Value 1-99 (Default=10) Page 47 P216E Max Dial Attempts for Scenario 2-Value 1-99 (Default=10) Page 47 P217E Max Dial Attempts for Scenario 3-Value 1-99 (Default=10) Page 47 P218E Max Dial Attempts for Scenario 4-Value 1-99 (Default=10) Page 47 PROGRAMMING TELEPHONE NUMBERS P221E Telephone Number 1 Page 47 P222E Telephone Number 2 Page 47 P223E Telephone Number 3 Page 47 P224E Telephone Number 4 Page 47 P225E Telephone Number 5 Page 47 P226E Telephone Number 6 Page 47 DEFINE REPORTING FORMATS P231E Define report format for phone number 1 - Default 1&6 Page 48 1 = Ademco Contact ID 5=Spare 2 = Elite Domestic Dial 6=Monitor call progress 3 = Pager format 7=Spare 4 = Speech Dial 8=Spare P232E Define report format for phone number 2 Page 48 P233E Define report format for phone number 3 Page 48 P234E Define report format for phone number 4 Page 48 P235E Define report format for phone number 5 Page 48 P236E Define report format for phone number 6 Page 48 ACTIVATION TO SCENARIO MAPPING P241E Zone 1 activation's mapped to scenario 1-4 default 1 Page 49 P242E Zone 2 activation's mapped to scenario 1-4 default 1 Page 49 P243E Zone 3 activation's mapped to scenario 1-4 default 1 Page 49 P244E Zone 4 activation's mapped to scenario 1-4 default 1 Page 49 P245E Zone 5 activation's mapped to scenario 1-4 default 1 Page 49 P246E Zone 6 activation's mapped to scenario 1-4 default 1 Page 49 P247E Zone 7 activation's mapped to scenario 1-4 default 1 Page 49 P248E Zone 8 activation's mapped to scenario 1-4 default 1 Page 49 P249E Zone 9 activation's mapped to scenario 1-4 default 1 Page 49 P250E Zone 10 activation's mapped to scenario 1-4 default 1 Page 49 P251E Zone 11 activation's mapped to scenario 1-4 default 1 Page 49 P252E Zone 12 activation's mapped to scenario 1-4 default 1 Page 49 P253E Zone 13 activation's mapped to scenario 1-4 default 1 Page 49 P254E Zone 14 activation's mapped to scenario 1-4 default 1 Page 49 P255E Zone 15 activation's mapped to scenario 1-4 default 1 Page 49 P256E Zone 16 activation's mapped to scenario 1-4 default 1 Page 49 MULTIPLE ZONE ACTIVATION REPORTING P346E Zones 1-8 will report multiple activation's - default on Page 49 P366E Zones 9-16 will report multiple activation's - default on Page 49 EXCLUDE TO SCENARIO MAPPING P461E Zone 1 exclude mapped to scenario 1-4 default 1 Page 49 P462E Zone 2 exclude mapped to scenario 1-4 default 1 Page 49 P463E Zone 3 exclude mapped to scenario 1-4 default 1 Page 49 P464E Zone 4 exclude mapped to scenario 1-4 default 1 Page 49 P465E Zone 5 exclude mapped to scenario 1-4 default 1 Page 49

P467E Zone 7 exclude mapped to scenario 1-4 default 1 Page 49 P468E Zone 8 exclude mapped to scenario 1-4 default 1 Page 49 P469E Zone 9 exclude mapped to scenario 1-4 default 1 Page 49 P470E Zone 10 exclude mapped to scenario 1-4 default 1 Page 49 P471E Zone 11 exclude mapped to scenario 1-4 default 1 Page 49 P472E Zone 12 exclude mapped to scenario 1-4 default 1 Page 49 P473E Zone 13 exclude mapped to scenario 1-4 default 1 Page 49 P474E Zone 14 exclude mapped to scenario 1-4 default 1 Page 49 P475E Zone 15 exclude mapped to scenario 1-4 default 1 Page 49 P476E Zone 16 exclude mapped to scenario 1-4 default 1 Page 49 LOW ZONE TAMPERS TO SCENARIO MAPPING P481E Low zone 1 tamper alarms mapped to scenario 1-4 default 1 Page 50 P482E Low zone 2 tamper alarms mapped to scenario 1-4 default 1 Page 50 P483E Low zone 3 tamper alarms mapped to scenario 1-4 default 1 Page 50 P484E Low zone 4 tamper alarms mapped to scenario 1-4 default 1 Page 50 P485E Low zone 5 tamper alarms mapped to scenario 1-4 default 1 Page 50 P486E Low zone 6 tamper alarms mapped to scenario 1-4 default 1 Page 50 P487E Low zone 7 tamper alarms mapped to scenario 1-4 default 1 Page 50 P488E Low zone 8 tamper alarms mapped to scenario 1-4 default 1 Page 50 HIGH ZONE TAMPERS TO SCENARIO MAPPING P491E High zone 1 tamper alarms mapped to scenario 1-4 default 1 Page 50 P492E High zone 2 tamper alarms mapped to scenario 1-4 default 1 Page 50 P493E High zone 3 tamper alarms mapped to scenario 1-4 default 1 Page 50 P494E High zone 4 tamper alarms mapped to scenario 1-4 default 1 Page 50 P495E High zone 5 tamper alarms mapped to scenario 1-4 default 1 Page 50 P496E High zone 6 tamper alarms mapped to scenario 1-4 default 1 Page 50 P497E High zone 7 tamper alarms mapped to scenario 1-4 default 1 Page 50 P498E High zone 8 tamper alarms mapped to scenario 1-4 default 1 Page 50 SYSTEM EVENTS TO SCENARIO MAPPING P311E Keypad Panic mapped to scenario 1-4 default 1 Page 50 P312E Battery low mapped to scenario 1-4 default 1 Page 50 P313E Mains ail mapped to scenario 1-4 default 1 Page 50 P314E Phone line restore mapped to scenario 1-4 default 1 Page 50 P315E Radio PIR battery low mapped to scenario 1-4 default 1 Page 50 P316E Radiokey battery low mapped to scenario 1-4 default 1 Page 50 P317E Keypad tamper mapped to scenario 1-4 default 1 Page 50 P318E Cabinet tamper mapped to scenario 1-4 default 1 Page 50 P319E Radio panic mapped to scenario 1-4 default 1 Page 50 P320E Test calls mapped to scenario 1-4 default 1 Page 50 REPORT 230V MAINS FAIL DELAY P460E Mains fail report delay 0-99 min - default = 60 Page 50 REPORT DELAY ON ZONES P450E Zone Dialler Reporting Delay (0-99 sec) - Default = 0 Page 51 AREA BASED REPORTING SCENARIO MAPPING P322E Area A reporting options Page 52 1 = Send set / unset 4 = Send duress alarms 2 = Send monitor on / off 5 = Enable 24hr alarms to voice/ 3 = Send unset only after activation's domestic 6 = Send set immediately

P324E Area B reporting options Page 52 P325E Area B reports mapped to scenario 1-4 default 1 Page 52 P326E Area C reporting options Page 52 P327E Area C reports mapped to scenario 1-4 default 1 Page 52 SYSTEM REPORTING OPTIONS P329E Auto-answer ring count - default = 0 Page 52 P260E System options Page 52 1 = Enable communicator 5 = Send restores 2 =DTMF or Decadic 6 = Send group number or 3 = NZ Style Decadic separate client code 4 = Blind dial 7 = Fax defeat 8 = Disable line monitoring P266E Account number for Area "A" - default 0000 Page 53 P267E Account number for Area "B" Page 53 P268E Account number for Area "C" Page 53 COMMAND CONTROL OPTIONS P261E Command code for output control Page 53 P262E Command code for Area "A" control Page 53 P263E Command code for Area "B" control Page 53 P264E Command code for Area "C" control Page 53 P680E Starting slot for status messages Page 53 CONTACT ID CODE ASSIGNMENTS P620E Duress Alarm - Default = 121 Page 54 P621E Zone 1 activation - default = 130 Page 54 P622E Zone 2 activation - default = 130 Page 54 P623E Zone 3 activation - default = 130 Page 54 P624E Zone 4 activation - default = 130 Page 54 P625E Zone 5 activation - default = 130 Page 54 P626E Zone 6 activation - default = 130 Page 54 P627E Zone 7 activation - default = 130 Page 54 P628E Zone 8 activation - default = 130 Page 54 P631E Zone 11 activation - default = 130 Page 54 P632E Zone 12 activation - default = 130 Page 54 P633E Zone 13 activation - default = 130 Page 54 P634E Zone 14 activation - default = 130 Page 54 P635E Zone 15 activation - default = 130 Page 54 P636E Zone 16 activation - default = 130 Page 54 P641E Zone 1 low tamper - default = 137 Page 54 P642E Zone 2 low tamper - default = 137 Page 54 P643E Zone 3 low tamper - default = 137 Page 54 P644E Zone 4 low tamper - default = 137 Page 54 P645E Zone 5 low tamper - default = 137 Page 54 P646E Zone 6 low tamper - default = 137 Page 54 P647E Zone 7 low tamper - default = 137 Page 54 P648E Zone 8 low tamper - default = 137 Page 54 P651E Zone 1 High tamper - default = 137 Page 54 P652E Zone 2 High tamper - default = 137 Page 54 P653E Zone 3 High tamper - default = 137 Page 54 P654E Zone 4 High tamper - default = 137 Page 54 P655E Zone 5 High tamper - default = 137 Page 54 P656E Zone 6 High tamper - default = 137 Page 54 P657E Zone 7 High tamper - default = 137 Page 54 P658E Zone 8 High tamper - default = 137 Page 54 ALARM VOICE MESSAGE MAPPING

P661E Voice message number 1-8 mapped to zone 1 activation - default 1 Page 54 P662E Voice message number 1-8 mapped to zone 2 activation - default 1 Page 54 P663E Voice message number 1-8 mapped to zone 3 activation - default 1 Page 54 P664E Voice message number 1-8 mapped to zone 4 activation - default 1 Page 54 P665E Voice message number 1-8 mapped to zone 5 activation - default 1 Page 54 P666E Voice message number 1-8 mapped to zone 6 activation - default 1 Page 54 P667E Voice message number 1-8 mapped to zone 7 activation - default 1 Page 54 P668E Voice message number 1-8 mapped to zone 8 activation - default 1 Page 54 P669E Voice message number 1-8 mapped to zone 9 activation - default 1 Page 54 P670E Voice message number 1-8 mapped to zone 10 activation - default 1 Page 54 P671E Voice message number 1-8 mapped to zone 11 activation - default 1 Page 54 P672E Voice message number 1-8 mapped to zone 12 activation - default 1 Page 54 P673E Voice message number 1-8 mapped to zone 13 activation - default 1 Page 54 P674E Voice message number 1-8 mapped to zone 14 activation - default 1 Page 54 P675E Voice message number 1-8 mapped to zone 15 activation - default 1 Page 54 P676E Voice message number 1-8 mapped to zone 16 activation - default 1 Page 54 P679E Voice message number 1-8 mapped to low battery alarm - default 0 Page 54 TEST CALLS P706E Test calls for days of the week 1-7 Page 56 P707E Test call time of the day Page 56 KEYPAD LISTEN IN OPTIONS P727E Keypad listen in options Page 56 1 = Only while dialling 2 = During entire call 3 = At all times UPLOAD/DOWNLOAD OPTIONS P718E XXXXXXXX. Up to 8 digit security code Page 55 P719E Upload/download option, Defaults = 1,2,3,4,5,6 & 7 Page 55 1E Data Transfer is allowed 2E Can Get Data "From Panel" 3E Can Send Data "To Panel" 4E Can Monitor Keypad Activity 5E Can Monitor Panel Status 6E Can Change Panel Status 7E Can clear event buffer 8E V21/Bell103(Off=Bell103,On=V21) P728E Answer incoming call (user initiated) Page 56 COMMON CONTACT ID CODES Page 56 CONTACT ID CODE SUMMARY Page 57

PRESS OR OR The mode for arming above depends upon the programmed panel operation. Also, the arming mode can vary from one keypad to another, depending upon how the system is programmed. If the arm sequence was successful, the relevant armed LED will turn on (ARMED, A or B) or a combination of these, depending upon the areas assigned to a particular user code. DISARMING THE PANEL PRESS If the disarm sequence was successful, the relevant armed LED (ARMED, A or B) will turn off depending upon the area/s assigned to a particular user code. EXCLUDING ZONES FIRST ARM THE ALARM AS ABOVE DURING THE EXIT DELAY PRESS (The exclude LED will turn ON). Next; Select any zone/s from 1-8 that you wish to exclude by pressing numbers 1-8 on the keypad. The appropriate green zone led will turn on to show that the zone/s will be excluded. To exclude zones 9-16 (if the panel is set up as a 16 zone panel); PRESS again. The "Aux." led should be ON. Now numbers 1-8 (and zone leds 1-8) will select 9-16 (eg 1=9 - 8=16) Once all the zones you wish to exclude have been selected; PRESS . This will then start the full exit delay timer and you should exit the building. MONITOR MODE ARMING PRESS OR Above choice depends upon programmed options. The relevant monitor led (either ARMED, A or B) will flash to indicate that monitor mode is on. MONITOR MODE DISARMING PRESS Monitor mode led (ARMED, A or B) will turn OFF. If the keypad is programmed for one button monitor mode disarming then simply pressing the button will disarm monitor mode. CONTROL OPERATION