AMX DG DVI MTP Quick Start Manual

AutoPatch DG DVI MTP Fiber Modules Overview DG (Digital Generation) DVI MTP® Fiber Transmitter (TX) and Receiver (RX) Modules work together (FIG. 2) or in conjunction with MTP Fiber boards on an AMX AutoPatch Distribution Matrix. This guide contains complete information for standalone use. For use with a distribution matrix, see the distribution matrix’s instruction manual on the AMX AutoPatch Software & Documentation CD or visit www.amx.com. A table containing EDID resolutions is included on the reverse. Product Specifications Mounting Options • Desktop – attach the rubber feet (included) on the bottom of the module. • Rack Trays & Mounting Brackets – contact your AMX representative for details. Installation Typical System Setup The TX receives DVI-D signals from 3 source devices and sends them over one fiber cable. The RX accepts the signals from the fiber cable, converts the signals back to DVI-D, and sends each signal to its corresponding destination device. Attaching Connectors Note: The DVI connector numbers on the TX and RX correspond to the Video Signal indicators on the front of the TX. To attach connectors: 1. Check EDID switch on front of TX to be sure that it remains set to the right (WP). 2. For each source device, insert the DVI connector into the DVI jack on the rear of the TX (FIG. 3). For DVI-I pinout, see FIG. 5. 3. For each destination device, insert the DVI connector into the DVI jack on the rear of the RX. Caution: Do not severely bend or kink the fiber cable. These actions can cause irreversible damage to the cable. 4. Insert the MTP/MPO plug on one end of the fiber cable into the Fiber (MTP/MPO) jack on the front of the TX (FIG. 4). 5. Insert the other end of the fiber cable into the Fiber jack on the front of the RX. 6. For each destination device, insert its DVI plug into a DVI jack on rear of the RX. 7. Insert the power plugs into the power jacks on the TX and RX (FIG. 4). 8. Plug the power transformers into the power sources. DVI-I TX & RX Module Connector Pinouts * The +5 V on pin 14 on the TX Module will supply a maximum of 55 mA. TX LED Indicators Video Signal Indicators Numbering corresponds to the numbering for DVI connectors on the rear of the TX. • Green – DVI signal path has a valid signal • Red – DVI signal path has lost its signal Fault Indicator (Optical) • OFF – Optical converter is functioning normally • Red – Optical converter has a fault condition Troubleshooting If an indicator on the TX is red, check its corresponding connector and the corresponding connector on the source device and then cycle power on the TX. MTP® is a registered trademark of US Conec, Ltd. FIG. 1 Transmitter (TX) FG1010-60 Receiver (RX) FG1010-63 Product Specifications Approvals CE Power Consumption (max.) +12 V - +24 V DC, 14 W Power Connector 2.1 mm DC power jack Humidity 0 to 90% non-condensing Operational Temperature 32° - 110° F (0° - 43° C) Dimensions 5.22 in. (13.26 cm) depth 5.82 in. (14.78 cm) width 1.42 in. (3.61 cm) height without feet Weight Approximately 1.5 lbs (0.68 kg) Compatible AMX AutoPatch Fiber Equipment DVI - MTP Fiber Modules RGBHV - MTP Fiber Modules Other AMX AutoPatch MTP Fiber products Resolution Support Up to 1920x1200 @ 60 Hz refresh rate w/ reduced blanking Up to 1600x1200 @ 60 Hz refresh rate DDC/EDID Support EDID provided by DVI TX Module (EDID resolution list on back) Pixel Bandwidth (bit rate) 1.65 Gbps Specification Compliant DVI 1.0, DVI-D (single link DVI) HDCP Support No Input Cable Equalization Up to 50 ft. (15.24 m) Fiber Cable Types 12 Fiber Multimode MTP, 50/125 µm or 62.5/125 µm Fiber Cable Length Up to 3000 ft. (914.4 m) cable requires low loss, controlled skew fiber cable, such as, Alcoa 50/125 µm Laser-Link 550 Fiber Cable Termination Female MTP Fiber Connector on Module Male MTP (guide pins define it as a male) DVI Connectors DVI-I (DVI-D is supported signal type) FIG. 2 Typical system setup Front Rear DVD Fiber up to 3000 ft. (914 m) FG1010-60 FG1010-63 TX RX Source devices Destination devices FIG. 3 Attach DVI connectors FIG. 4 Attach fiber cable & power cable FIG. 5 TX & RX DVI-I input & output pinouts DVI connectors Power jack Power indicator Video Signal indicators Fault indicator MTP connector EDID switch remains so source & destination can share information. set to WP (Write-Protect),

6/07 ©2007 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com 93-10-846 REV: A0 EDID Supported Resolutions EDID Supported Resolutions Resolution Refresh Rate 1920x1200 60 Hz reduced sync blanking only 1920x1080 60 Hz reduced sync blanking only 1680x1050 60 Hz 1600x1200 60 Hz 1280x1024 60 Hz - 75 Hz 1280x960 60 Hz - 75 Hz 1280x768 60 Hz - 85 Hz 1280x720 60 Hz - 85 Hz 1152x864 60 Hz - 85 Hz 1024x768 60 Hz - 85 Hz 800x600 60 Hz - 85 Hz 640x480 60 Hz - 85 Hz