Ledj LEDJ232 Operation & User’s Manual

Specifications

Brand: Ledj
Category: DJ Equipment
Model: LEDJ232 (Operation & User’s Manual)
File Type: PDF
File Size: —
Pages: 12

Read Online

Read the Ledj LEDJ232 Operation & User’s Manual online using the built-in PDF viewer.

Text of the manual

Event Spot DL/WW User Manual

2 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! •� Before�your�initial�start-up,�please�make�sure�that�there�is�no�damage�caused�during�transportation. •� Should�there�be�any�damage,�consult�your�dealer�and�do�not�use�the�equipment. •� To�maintain�the�equipment�in�good�working�condition�and�to�ensure�safe�operation,�it�is�necessary�� for�the�user�to�follow�the�safety�instructions�and�warning�notes�written�in�this�manual. •� Please�note�that�damages�caused�by�user�modifications�to�this�equipment�are�not�subject�to�warranty. IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment. OPERATING DETERMINATIONS If�this�equipment�is�operated�in�any�other�way,�than�those�described�in�this�manual,�the�product�may�suffer�damage�and�� the�warranty�becomes�void.�Incorrect�operation�may�lead�to�danger�e.g:�short-circuit,�burns�and�electric�shocks�etc.� Do�not�endanger�your�own�safety�and�the�safety�of�others!� Incorrect�installation�or�use�can�cause�serious�damage�to�people�and/or�property. CAUTION! KEEP THIS EQUIPMENT AWAY FROM RAIN, MOISTURE AND LIQUIDS CAUTION! TAKE CARE USING THIS EQUIPMENT! HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!! •� Never�let�the�power�cable�come�into�contact�with�other� cables.�Handle�the�power�cable�and�all�mains�voltage�� connections�with�particular�caution! •� Never�remove�warning�or�informative�labels�from�the�unit. •� Do�not�open�the�equipment�and�do�not�modify�the�unit. •� Do�not�connect�this�equipment�to�a�dimmer�pack. •� Do�not�switch�the�equipment�on�and�off�in�short�intervals,� as�this�will�reduce�the�system’s�life. •� Only�use�the�equipment�indoors. •� Do�not�expose�to�flammable�sources,�liquids�or�gases. •� Always�disconnect�the�power�from�the�mains�when�� equipment�is�not�in�use�or�before�cleaning!�Only�handle� the�power-cable�by�the�plug.�Never�pull�out�the�plug�by� pulling�the�power-cable. •� Make�sure�that�the�available�mains�supply�voltage�is� between�100~240V�AC,�50/60Hz. •� Make�sure�that�the�power�cable�is�never�crimped�or�� damaged.�Check�the�equipment�and�the�power�cable� periodically. •� If�the�equipment�is�dropped�or�damaged,�disconnect�the� mains�power�supply�immediately�and�have�a�qualified� engineer�inspect�the�equipment�before�operating�again.� � •� If�the�equipment�has�been�exposed�to�drastic�� temperature�fluctuation�(e.g.�after�transportation),�� do�not�connect�power�or�switch�it�on�immediately.�� The�arising�condensation�might�damage�the�equipment.� Leave�the�equipment�switched�off�until�it�has�reached� room�temperature. •� If�your�product�fails�to�function�correctly,�stop�use� immediately.�Pack�the�unit�securely�(preferably�in�the�� original�packing�material),�and�return�it�to�your�Pro�Light� dealer�for�service. •� Only�use�fuses�of�same�type�and�rating. •� Repairs,�servicing�and�power�connection�must�only�be�� carried�out�by�a�qualified�technician.�THIS�UNIT�CONTAINS� NO�USER�SERVICEABLE�PARTS. •� This�lighting�fixture�is�for�professional�use�only�-�it�is� not�designed�for�or�suitable�for�household�use.�The� product�must�be�installed�by�a�qualified�technician�in� accordance�with�local�territory�regulations.�The�safety�of� the�installation�is�the�responsibility�of�the�installer.�The� fixture�presents�risks�of�severe�injury�or�death�due�to�fire� hazards,�electric�shock�and�falls. •� Warning!�Risk�Group�2�LED�product�according�to� EN�62471.�Do�not�view�the�light�output�with�optical� instruments�or�any�device�that�may�concentrate�the�beam. •� WARRANTY:�One�year�from�date�of�purchase.

Event Spot DL/WW User Manual

3 0m 2m 3m 4m 5m 1m 10° 45° 4° 54400 28400 13640 7109 6040 3160 3400 1780 2180 1140 4° - Lux 10° - Lux 3140 786 349 197 126 45° - Lux Event Spot DL 47600 24000 11890 5989 5290 2660 2980 1500 1900 958 4° - Lux 10° - Lux 2620 654 291 164 105 45° - Lux Event Spot WW Product overview & technical specifications The�Event�Spot�compact LED�Pinspots�are�powered�by�a�15W�LED�that�has�the�brightness�and�output�of�a�100W� halogen�lamp.�Featuring�a�4°�beam�angle�and�supplied�with�two�optional�lenses�(10°�and�45°)�the�fixture�is�easily� directed�at�displays�for�highlighting�and�pinspotting,�it�can�also�be�used�to�create�mood�lighting�on�a�restaurant� table,�or�to�spotlight�displays�in�store.� Event Spot DL/WW 135mm 173mm 203mm •�1�x�15W�warm�white�LED�(3000K)�-�LEDJ232 •�1�x�15W�day�light�LED�(5000K)�-�LEDJ233 •�Beam�angle:�4°�native,�10°�&�45°�frost�lenses�supplied •�1.1kHz�refresh�rate •�DMX�channels:�2 •�Manual�and�master/slave�modes •�0-100%�dimming�and�variable�strobe •�Bracket�allows�for�multiple�rigging�or�floor�standing�applications •�4�push�button�menu�with�LCD�display •�IEC�power�input/output�trailing�sockets •�3-Pin�XLR�input/output�trailing�sockets •�Convection�cooled •�Optional�IR�remote�(LEDJ90E) Specifications Event Spot DL/WW Power�consumption 17W Power�supply 100~240V,�50/60Hz Fuse T0.5A�250V Dimensions 203�x�135�x�173mm Weight 1.2kg Order�code LEDJ232�-�WW�Version Order�code LEDJ233�-�DL�Version

Event Spot DL/WW User Manual

4 Technical specifications 01�-�Earth�point 02�-�LCD�display 03�-�Function�buttons 04�-�3-Pin�DMX�input�trailing�socket 05�-�3-Pin�DMX�output�trailing�socket 06�-�IEC�power�input�trailing�socket 07�-�IEC�power�output�trailing�socket 08�-�Fuse�T0.5A�250V 09�-�Hanging�bracket 10�-�Hanging�bracket�adjustable�knob In�the�box:�1 x fixture, 1 x 10° frost lens, 1 x 45° frost lens, 1 x power cable & 1 x user manual MENU UP ENTER 100-240V ~50/60Hz FUSE: T0.5A 250V DOWN POWER OUTPUT POWER INPUT DMX INPUT DMX OUTPUT 10 09 01 06 03 04 10 05 08 07 02

Event Spot DL/WW User Manual

5 Operating instructions MENU DMX MODE ADDR DMX address setting DMX ADDR 001 DMX ADDR 512 IR. REMOTE IR remote on/off IR. REMOTE OFF IR. REMOTE ON DIMMER Dimmer response DIMMER RESP_01 DIMMER RESP_02 Manual Dim: F: Manual mode Manual Dim:00 F:00 Manual Dim:99 F:99 CHANNEL CH 02 DMX channel mode SLAVE MODE Slave mode

Event Spot DL/WW User Manual

6 DMX mode: Operating�in�a�DMX�control�mode�environment�gives�the�user�the�greatest�flexibility�when�it�comes�� to�customising�or�creating�a�show.�In�this�mode�you�will�be�able�to�control�each�individual�trait�of�the� fixture�and�each�fixture�independently.� To�access�the�DMX�address�mode,�press�the�“MENU”�button�on�the�rear�of�the�unit�to�show�� “DMX MODE ADDR” on�the�LCD�display.�Now�press�the�“ENTER”�button�and�use�the�“UP”�and�“DOWN”� buttons�to�set�the�required�DMX�address.�Press�the�“ENTER”�button�to�confirm�the�setting. To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button.� To�access�the�DMX�channel�mode,�press�the�“MENU”�button�on�the�rear�of�the�unit�to�show�� “CHANNEL CH 02” on�the�LCD�display.�Press�the�“ENTER”�button�to�confirm�the�setting. To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button. Master/slave mode: To�set�the�master�unit,�press�the�“MENU”�button�on�the�rear�of�the�master�unit�to�select�manual�mode.� To�set�the�other�units�in�slave�mode,�press�the�“MENU”�button�on�the�rear�of�the�unit�to�show�“SLAVE MODE”�on�the�LCD�display.�Press�the�“ENTER”�button�to�confirm�the�setting. To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button. IR remote on/off: To�set�the�IR�remote�on/off,�press�the�“MENU”�button�on�the�rear�of�the�unit�to�show�“IR. REMOTE”�on� the�LCD�display.�Press�the�“ENTER”�button�and�use�the�“UP”�and�“DOWN”�buttons�to�select�“ON” or “OFF”.�Press�the�“ENTER”�button�to�confirm�the�setting. To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button. Dimmer response: To�set�the�dimmer�response,�press�the�“MENU”�button�on�the�rear�of�the�unit�to�show�“DIMMER”�on�the� LCD�display.�Press�the�“ENTER”�button�and�use�the�“UP”�and�“DOWN”�buttons�to�select�“RESP_01” or “RESP_02”.�Press�the�“ENTER”�button�to�confirm�the�setting. To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button. Operating instructions Channel Value Function 1 000-255 Master�dimmer�(0-100%) 2 000-002 No�function 003-255 Strobe�(slow-fast) 2 channel mode:

Event Spot DL/WW User Manual

7 Manual dimming mode: To�access�the�manual�dimming�mode,�press�the�“MENU”�button�on�the�rear�of�the�unit�to�show�� “Manual”�on�the�LCD�display.�The�unit�is�now�in�manual�dimming�mode.�Press�the�“ENTER”�button�� and�use�the�“UP”�and�“DOWN”�buttons�to�set�the�brightness�from�“00” - “99”.�Press�the�“ENTER”�button�� again�and�use�the�“UP”�and�“DOWN”�buttons�to�set�the�strobe�speed�from�“00” - “99”.� Press�the�“ENTER”�button�to�confirm�the�setting. (00 = LED off/strobe off, 99 = LED at full brightness/strobe fast) To�exit�out�of�any�of�the�above�options,�press�the�“MENU”�button.� Operating instructions

Event Spot DL/WW User Manual

8 Optional IR remote functions:� Button functions: DMX address examples: To�set�the�DMX�address; •�Press�the�“S”�button,�the�LED�illuminates�in�full,�you�can�now�start�to�set�the�DMX�address •�Select�the�required�3�digit�DMX�address�(eg�001�or�136�or�275)�the�unit�will�then�flash�� to�confirm�the�address�has�been�set •�Now�press�the�“DMX�MODE”�button�to�save�the�new�address�into�the�memory Important notes: •�Set�the�DMX�address�on�each�fixture�before�plugging�into�the�DMX�controller •�The�IR�remote�is�cannot�be�used�when�the�fixture(s)�are�being�controlled�by�a�DMX�controller •�The�maximum�transmitter�distance�is�10m�-�Please�make�sure�that�you�have�the�IR�remote�aimed� directly�at�the�front�panel�of�each�fixture�to�be�programmed •�If�you�do�not�press�the�“DMX�MODE”�button�after�you�have�changed�the�DMX�address,�� when�you�power�down�the�fixture�it�will�lose�the�address�you�have�set 01�-�Blackout 02�-�To�set�the�brightness�of�the�LED�either�� ����select�20%,�50%�or�100%�or�alternatively�� ����you�can�use�the�‘+’�and�‘-’�buttons 03�-�Flash�off 04�-�To�set�the�flash�speed�of�the�LED�either�� ����select�20%,�50%�or�100%�or�alternatively�� ����you�can�use�the�‘+’�and�‘-’�buttons 05�-�Set�the�LED�into�DMX�mode 06�-�Set�the�LED�into�sound�active�mode 07�-�Set�the�LED�into�slave�mode 08�-�Set�the�DMX�address�for�the�LED 1 2 3 4 5 6 0 + _ 7 8 9 D SL S OFF 20% 50% 100% SA STROBE OFF 20% 50% 100% DIMMING SLAVE SET ADDR SOUND ACTIVE DMX MODE 01 04 02 07 06 05 08 Optional IR remote Order code: LEDJ90E 03 Operating instructions

Event Spot DL/WW User Manual

9 Setting the DMX address: The�DMX�mode�enables�the�use�of�a�universal�DMX�controller.�Each�fixture�requires�a�“start�address”� from�1-�511.�A�fixture�requiring�one�or�more�channels�for�control�begins�to�read�the�data�on�the�channel� indicated�by�the�start�address.�For�example,�a�fixture�that�occupies�or�uses�7�channels�of�DMX�and�was� addressed�to�start�on�DMX�channel�100,�would�read�data�from�channels:�100,101,102,103,104,105� and�106.�Choose�a�start�address�so�that�the�channels�used�do�not�overlap.�E.g.�the�next�unit�in�the� chain�starts�at�107. DMX 512: DMX�(Digital�Multiplex)�is�a�universal�protocol�used�as�a�form�of�communication�between�intelligent� fixtures�and�controllers.�A�DMX�controller�sends�DMX�data�instructions�form�the�controller�to�the�fixture.� DMX�data�is�sent�as�serial�data�that�travels�from�fixture�to�fixture�via�the�DATA�“IN”�and�DATA�“OUT”�� XLR�terminals�located�on�all�DMX�fixtures�(most�controllers�only�have�a�data�“out”�terminal). DMX linking: DMX�is�a�language�allowing�all�makes�and�models�of�different�manufactures�to�be�linked�together�� and�operate�from�a�single�controller,�as�long�as�all�fixtures�and�the�controller�are�DMX�compliant.�� To�ensure�proper�DMX�data�transmission,�when�using�several�DMX�fixtures�try�to�use�the�shortest�� cable�path�possible.�The�order�in�which�fixtures�are�connected�in�a�DMX�line�does�not�influence�the�� DMX�addressing.�For�example;�a�fixture�assigned�to�a�DMX�address�of�1�may�be�placed�anywhere�in�� a�DMX�line,�at�the�beginning,�at�the�end,�or�anywhere�in�the�middle.�When�a�fixture�is�assigned�a�� DMX�address�of�1,�the�DMX�controller�knows�to�send�DATA�assigned�to�address�1�to�that�unit,�� no�matter�where�it�is�located�in�the�DMX�chain. DATA cable (DMX cable) requirements (for DMX operation): This�fixture�can�be�controlled�via�DMX-512�protocol.�The�DMX�address�is�set�on�the�back�of�the�unit.� Your�unit�and�your�DMX�controller�require�a�standard�3-pin�XLR�connector�for�data�input/output,�� see�image�below. Note: DMX cable must be daisy chained and cannot be split. DMX setup Further�DMX�cables�can�be� purchased�from�all�good�sound� and�lighting�suppliers�or�� Pro�Light�Concepts�dealers. Please�quote: CABL10 – 2m CABL11 – 5m CABL12 – 10m

Event Spot DL/WW User Manual

10 Notice: Be�sure�to�follow�the�diagrams�below�when�making�your�own�cables.�Do�not�connect�the�cables�� shield�conductor�to�the�ground�lug�or�allow�the�shield�conductor�to�come�in�contact�with�the�XLRs�� outer�casing.�Grounding�the�shield�could�cause�a�short�circuit�and�erratic�behaviour. Special note: Line termination: When�longer�runs�of�cable�are�used,�� you�may�need�to�use�a�terminator�on�� the�last�unit�to�avoid�erratic�behaviour. Using a cable terminator will decrease the possibilities of erratic behaviour. (3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89) 5-pin XLR DMX connectors: Some�manufactures�use�5-pin�XLR�connectors�for�data�transmission�in�place�of�3-pin.�5-pin�XLR�fixtures� may�be�implemented�in�a�3-pin�XLR�DMX�line.�When�inserting�standard�5-pin�XLR�connectors�in�to�a� 3-pin�line�a�cable�adaptor�must�be�used.�The�diagram�below�details�the�correct�cable�conversion. Termination�reduces�signal�transmission� problems�and�interference.�It�is�always� advisable�to�connect�a�DMX�terminal,� (resistance�120�Ohm�1/4�W)�between�pin�2� (DMX-)�and�pin�3�(DMX+)�of�the�last�fixture. 5-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C 3-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) 3-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) 5-pin XLR (socket) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C DMX setup

Event Spot DL/WW User Manual

11 WEEE notice Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This�marking�shown�on�the�product�or�its�literature,�indicates�that�it�should�not�be�disposed�� with�other�household�wastes�at�the�end�of�its�working�life.�To�prevent�possible�harm�to�the�� environment�or�human�health�from�uncontrolled�waste�disposal,�please�separate�this�from�other� types�of�wastes�and�recycle�it�responsibly�to�promote�the�sustainable�reuse�of�material�resources. Household�users�should�contact�either�the�retailer�where�they�purchased�this�product,�or�their� local�government�office,�for�details�of�where�and�how�they�can�take�this�item�for�environmentally� safe�recycling. Business�users�should�contact�their�supplier�and�check�the�terms�and�conditions�of�the�� purchase�contract.�This�product�should�not�be�mixed�with�other�commercial�wastes�for�disposal.

Other DJ Equipment Manuals