Mannesmann MT-CNC Quick Reference Manual

Rev C, 10/97 MUI Flow Charts 1-33 1.30 Exiting (from any screen back to the MUI Main Menu) Figure 1-33 Exiting (from any screen back to MUI Main Menu) to return to Main Menu MUI Main Menu From any screen within -F5 Ctrl-F7 - Oscilloscope Function to return to Parameter Index Menu to return to Main Menu MUI Main Menu From any screen within -F4 - Global Documentation to return to Main Menu MUI Main Menu From any screen within -F8 - Programmable Controller (SPS) to return to Main Menu MUI Main Menu From any ...

Rev C, 10/97 NC Programming 4-39 ACD_COMP ACtual Data for NC-COMPiler (5) Value range: Allows to embed the actual value of a NC-variable at the time of NC-program compilation and download. ...

Rev C, 10/97 Gateway Signals 6-55 6.17.5 Axis Control Signals (qAXIS) Table 6-34: INDRAMAT_DATA_TYPE qAXIS declaration (*AXIS CONTROL GATEWAY SIGNALS*) 0x.12/xx - 0x.13/xx SOFTWARE VERSION 0x.14/xx and above SOFTWARE VERSION Type Description A01C %QW0.0 A#A01C or %QW0.0 qAXIS (*AXIS 1 CONTROL*) A02C %QW0.8 A#A02C or %QW0.20 qAXIS (*AXIS 2 CONTROL*) A03C %QW0.16 A#A03C or %QW0.40 qAXIS (*AXIS 3 CONTROL*) A04C %QW0.24 A#A04C or %QW0.60 qAXIS (*AXIS 4 CONTROL*) A05C %QW0.32 A#A05C or %QW0.80 qAXIS (*AXIS 5 CONTROL*) A06C %QW0.40 ...

6-54 Gateway Signals Rev C, 10/97 6.17.4 External Mechanism Status Signals (iMECH) Table 6-33: INDRAMAT_DATA_TYPE iMECH declaration (*EXTERNAL MECHANISM STATUS GATEWAY SIGNALS*) 0x.12/xx - 0x.13/xx SOFTWARE VERSION 0x.14/xx and above SOFTWARE VERSION Type Description M07S %IW0.332 A#M07S or %IW0.704 iMECH (*EXT. MECHANISM 7 STATUS*) M08S %IW0.340 A#M08S or %IW0.712 iMECH (*EXT. MECHANISM 8 STATUS*) M09S %IW0.348 A#M09S or %IW0.720 iMECH (*EXT. MECHANISM 9 STATUS*) M10S %IW0.356 A#M10S or %IW0.728 iMECH (*EXT. MECHANISM 10 STATUS*) M11S ...

5-72 SPS Instruction Set Rev C, 10/97 No. Comment 246 Invalid input parameter PROTOKOL; the PROTOKOL number for the serial interface type specified in the selection of the serial interface parameters is negative or too high. 247 Invalid input parameter HANDSH; the HANDSH number for the handshake type specified in the selection of the serial interface parameters is negative or too high. 248 Interface cannot be found; the interface that has been specified in the selection of the serial interface parameters cannot be found. 249 All COM interfaces open; all serial ...

4-28 NC Programming Rev C, 10/97 NOTE: The operand of the function TAN (X) depends on the active angle unit “radians” (NC-command RAD) or “degrees” (NC-command DEG). The values (PI/2,-PI/2), (+90,-90) are not defined and will result in a process error when used with TAN. ...

5-60 SPS Instruction Set Rev C, 10/97 time, etc.). The unit that wants to use it must reserve the required space. Declaration of the FB assignments in a separate declaration editor. • Utilization according to the selected entry language. A user function block may utilize standard functions, firmware functions, user functions, user function blocks, standard function blocks, and firmware function blocks. Nesting can be continued to any depth. NOT ALLOWED is that function block 'A' employs itself (recursive utilization), or that function block 'A' employs functi ...

2-30 GUI Flow Charts Rev C, 10/97 2.5.5 Digital Drive Parameter Editing, GUI (Indramat default) Figure 2-29 GUI Digital Drive Editing (this chart is only valid for the default GUI screens supplied with the installation diskettes) GUI Default Main Menu Setup/Config Machine Parameter Drive Param move pointer to the desired Drive to select Change Mode select 'Parameter Mode' (drives will change to P2 status) move pointer to the Parameter that will be modified Modify or to begin modification modify more ...