Datecs INFINEAX-MINI Operation & User’s Manual

User manual ` 2 THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. VERSION: January 2017

User manual ` 3 Version Description Date 1.0 First release 27.01.2016 2.0 Updated all document 09.01.2017

User manual ` 4 Legal Notice “Made for iPad” mean that an electronic accesory has been designed to connect specifically to iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible fort he operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPad may affect wireless performance. Compatibility Made for iPad mini iPad are trademark of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc.

User manual ` 5 FCC Notice FCC ID: YRWINFINEAX-M This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. No changes shall be made to the equipment without the manufacturer’s permission as this may void the user’s authority to operate the equipment. Exposure to Radio Frequency (RF) Signals The InfineaX-Mini, incorporating the iPad Mini, has been tested and meets applicable limits for radio frequency (RF) exposure. Specific Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. The SAR limit is 1.6 watts per kilogram averaged over 1 gram of tissue. During testing, the iPad Mini devices, incorporated within the InfineaX-Mini, are set to their highest transmission levels and placed in position that simulate use against the body, with 5mm separation. Carry the InfineaX-Mini at least 5mm away from your body to ensure exposure levels remain at or below the as-tested levels. Cases with metal parts may change the RF performance of the device, including its compliance with RF exposure guidelines, in a manner that has not been tested or certified. The InfineaX-Mini complies with the FCC safety requirements for RF exposure in accordance with FCC rule part §2.1093 and KDB447498 D01 for portable use conditions. The InfineaX-Mini, incorporating the iPad Mini, must not be co-located antennas or transmitters not inherent to the iPad

User manual ` 6 CONTENTS Legal Notice ............................................................................................................................................................. 4 Compatibility ........................................................................................................................................................... 4 1. Technical specification ........................................................................................................................................ 7 2. Box Contents ....................................................................................................................................................... 8 3. General View ....................................................................................................................................................... 9 4. Operation Modes .............................................................................................................................................. 12 4.1 Battery status level (for devices with fuel gauge) ..................................................................................... 12 4.2 Charging indication and current select ...................................................................................................... 12 4.3 Automatic charge (for devices with fuel gauge) ........................................................................................ 12 4.4 Vibration on scan ....................................................................................................................................... 12 4.5 Pass-through sync through mini USB ........................................................................................................ 12 4.6 Enable external speaker ............................................................................................................................ 12 4.7 Bluetooth transferring data ....................................................................................................................... 12 4.8 Reset the InfineaX-Mini ............................................................................................................................. 12 4.9 Reset Barcode engine ................................................................................................................................ 13 4.10 Update firmware of the device ............................................................................................................... 13 4.11 Update firmware of Barcode engine ....................................................................................................... 13 4.12 RF card reading ........................................................................................................................................ 13

User manual ` 7 1. Technical specification Processor 32-bit ARMTM CortexTM - M3 based Microcontroller Barcode Reader (option) • Intermec EA-30* - Image Sensor 752 x 480 CMOS, High Performance 2D Imager Scan Engine • Intermec EA-31 - Image Sensor 752 x 480 CMOS, High Performance 2D Imager Scan Engine Supported Barcode Types * Imager Supported Symbologies: 1D symbologies: EAN/UPC, GS1 Databar (limited expanded & omni-directional), RSS, Code 39, Code 128, UCC/EAN 128, ISBN, ISBT, Interleaved/Matrix/ Industrial and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI, Plessey, Telepen, postal codes (Australian Post, BPO, Canada Post, Dutch Post, Japan Post, PostNet, Sweden Post) 2D symbologies: Data Matrix, PDF417, Micro PDF 417, Codablock, Maxicode, QR, Aztec, GS1 composite codes, Direct Part Marking Reading multicodes and barcodes on mobile phone screens available. Battery • Fuel Gauge microcontroller for remaining battery capacity, state-of-charge, battery voltage and etc. • Rechargeable hard pack Li-Ion Battery 3.7V / 1900 mAh • Rechargeable hard pack Li-Ion Battery 3.7V / 3800 mAh (option) Connectivity • Apple 9 pin connector • Pass-through sync through special 4 pin waterproof connector • Pass-through sync through mini USB • BT 2.0 Class 2 (option) • 3.5 mm TRRS Audio Jack Device compatibility Apple iPad mini Buttons • 6 x Scan buttons • Battery status button LED indication 18 LEDs for battery and emergency status Audio indication Electro-Magnetic Buzzer Vibration capabilities Micro Vibration Motor - Rated speed: 14,000 ± 2,000rpm Sound capabilities • 1.7-W mono fully differential audio power amplifier • Front Speaker – 150mW • 2 x Rear Speakers – 2 x 750mW • 2 x Electret Condenser Microphones Certifications FCC, Apple® Mfi Weight, g 510g with battery and 2D barcode reader (without iPad Mini) Dimensions (LxWxH), mm 235 x 160 x 36 Environmental • Operating: -10oC to +40oC / 5% to 90% RH • Storage: -20oC to +50oC / 5% to 90% RH Power Supply • 5V through special 4 pin waterproof connector • 5V through single or 5 station charger * Specifications subject to change without notice.

User manual ` 8 2. Box Contents Item Part Number Descriptions Image 1 InfineaX-Mini InfineaX-Mini Scanner 2 USB A to mini B(0.9m) USB sync cable 3 InfineaX-Mini User Manual User's manual

User manual ` 9 3. General View Front Speaker Microphones Home button Scan Engine

User manual ` 10 Battery Status Button Rear Speakers/Front Speaker Switch Battery RF card reader Rear Speakers

User manual ` 11 LEDs indications mini USB connector LEDs indications Volume buttons

User manual ` 12 4. Operation Modes To insert iPad mini in InfineaX-Mini, first remove all eight screws from top cover. Then attach iPad mini to 9-pin lightning connector. After that, insert audio jack in iPad mini connector. 4.1 Battery status level (Press battery level button) - Battery percentage above 75% – LEDs flash on green - Battery percentage between 50-75% – LEDs blinks on green - Battery percentage between 25-50% – LEDs blinks on orange - Battery percentage between 10-25% – LEDs blinks on red - Battery percentage under 10% – One red LED is blinks (In operating mode) - Low battery indicator - Battery percentage under 25% - one red LED is light all the time 4.2 Charging indication and current select - When the device is charging, green led is light - Charging current of iOS device can be select between 500mA and 1000mA, when is charging via USB adapter 4.3 Automatic charge - When the battery level is above 25% – InfineaX-Mini is automatically start to charge iPad Mini. When battery level is drop under 10%, charge automatically will stop. 4.4 Vibration on scan - This function can be enabled or disabled 4.5 Pass-through sync through mini USB - Transferring data between iPad Mini and PC or MAC. This function can be enable or disable. 4.6 Enable external speaker - This function can be enabled or disabled (from setting or with right side button), switch between rear and front speaker. - When the rear speaker is active, blue led will light. 4.7 Bluetooth transferring data - This function is allow to transfer data with other device via Bluetooth. 4.8 Reset the InfineaX-Mini - Holding on same time status and scan button for ~5sec

User manual ` 13 4.9 Reset Barcode engine - When is selected, barcode engine will return to default values. 4.10 Update firmware of the device - Firmware of InfineaX-Mini can be update for application. Before proceed update make it sure, battery of the iOS device and InfineaX-Mini is more that 20%. 4.11 Update firmware of Barcode engine - Firmware of barcode engine can be update from application. Before proceed update make it sure, battery of the iOS device and InfineaX-Mini is more that 20%. Some of the operating modes, may be different, depends of the firmware version. 4.12 RF card reading - Start the application for iOS and select tab “RF”. Then place the card on the spot with RF symbol (backside of the device).