DFI KS070-BT Installation Manual

Package Contents • One 7" Touch Panel PC • One sheet of Poron foam • One HDD drive bay kit • 1 DVD disk includes: - Manual DFI reserves the right to change the specifi cations at any time prior to the product's release. For the latest revision and more details of the installation procedure, please refer to the user's manual on the website. www.dfi .com

Antenna hole Reset Power button (Green LED) COM 1 (RS232/RS422/RS485) Status LED (Blue) Antenna hole Line-out Bottom View COM 3 (RS232/RS422/RS485) USB 2.0 LAN 2 DC-in Mic-in LAN 1

1. Make sure the system and all other peripheral devices connected to it have been powered-off. 2. Disconnect all power cords and cables. 3. The 8 mounting screws on the rear side of the system are used to secure the cover to the chassis. Remove these screws and put them in a safe place for later use. 4. Lift the cover up to open the system. 5. The Mini PCIe and the micro SD slots are readily accessible after removing the chassis cover. Mounting screw Mounting screw

2. Align the mounting holes of the SATA HDD with the mounting holes on the HDD drive bay and use the provided mounting screws to attach the SATA HDD to the drive bay. 1. The SATA data and power connectors are on the system board. SATA mounting location SATA connectors Mounting screw Mounting screw

connectors on the SATA drive and the other end of the SATA cable to the SATA power and data connectors on the system board. 4. Align the mounting holes of the HDD drive bay with the mounting holes on the system and use the provided mounting screws to secure the drive bay in place. SATA power/data cable SATA drive Mounting screw SATA drive SATA connectors

Note: The system also has one additional full-size Mini PCIe and one half-size Mini PCIe slot that uses PCIe and LPC interface respectively. The system board is equipped with 3 Mini PCIe slots: two full-size and one half-size slots. Here we will demonstrate the installation of a full-size Mini PCIe card (mSATA interface) for capacity expansion. 1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card with the notch in the connector on the system board. 2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on the system board. Mounting screw

• 2 wall mount brackets • Bracket screws 2. Select a place on the wall where you will mount the Panel PC. 3. Use the provided mounting screws to attach “wall mount bracket 1” to the wall. Mounting Options Wall mount Wall mount bracket 1 Wall mount bracket 2 Wall mount bracket 1 Mounting screw 1. Before starting any installation procedures, attach the poron foam to the Panel PC. Poron foam

Panel PC. Wall mount bracket 2 Mounting screw Hooks Screw 5. Slide the Panel PC to "wall mount bracket 1" to attach the two brackets with the hooks. Then tighten the screw to secure the assembly in place.

• 6 mounting clamps 2. Select a place on the panel (or wall) where you will mount the Panel PC. 3. Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (202.5mm x 140.3mm) and ensure that the Panel PC can be fi tted into the panel properly. 4. Insert the Panel PC from the outside surface of the panel into the mounting hole until it is properly fi tted against the panel. 5. Position the mounting clamps along the rear edges of the Panel PC and insert them into the slits around the Panel PC. 1. Before starting any installation procedures, attach the poron foam to the Panel PC. Poron foam Panel Mounting hole 202.5 140.3

prior to mounting the rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the white plastic cap onto the back of the panel. The illustration below shows that all clamps are properly mounted. White plastic cap fi Slit for mounting the clamp Mounting clamp Note: The maximum thickness of your panel’s mounting wall should be 10 mm for secure panel mount.

LAN 2 LAN 1 3 DDR3L DDR3L DDR3L DDR3L Mini PCIe with SIM COM 4 RS232/RS422/RS485 12 10 3 1 JP22 1 1 1 (JP20) (JP18) (JP17) (JP21) 1 3 12 10 COM 2 RS232/RS422/RS485 COM 1 RS232/RS422/RS485 USB 0 USB 3.0 HDMI Reset Power 39 40 2 1 LVDS LCD Panel USB 7 USB 6 Mic-in 1 Battery Buzzer 1 Chassis Intrusion 1 Clear CMOS Data (JP24) SPI Flash BIOS eMMC (optional) iTE IT8528E Mini PCIe with LPC mSATA MicroSD (optional) 1 System Fan 1 USB 0 Power Select (JP5) 1 2 5 6 (JP23) 1 1 1 (JP3) (JP4) 1 2 10 9 COM 6 1 10 9 COM 5 1 1 USB 2 Power Select (JP6) USB 5-7 Power Select (JP7) 1 2 10 9 USB 5 (JP25) USB 2.0 USB 2.0 (JP17) (JP20) COM 4/DIO Select (JP22, JP21) Digital I/O 0-3 Output State Digital I/O Power Select Panel Power Select (JP3) (JP4) (JP23) Backlight Enable Power Select Auto Power-on Select (JP25) Dimming Mode Select (JP18) Digital I/O 4-7 Output State 1 COM 3 RS232/RS422/RS485 4 1 (JP2) (JP2) LCD/Inverter Power Select SATA 1 4 1 SATA Power 1 SATA 2.0 Line-out DC-in USB 2 U USB 2 U USB 2 USB 2 USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7) +5V_standby (default) 1-2 On +5V 2-3 On Clear CMOS Data JP24 Normal (default) 1-2 On Clear CMOS Data 2-3 On Panel Power Select JP23 +12V 1-2 On +5V 3-4 On +3.3V (default) 5-6 On Auto Power-on Select JP25 Power-on via power button (default) 1-2 On Power-on via AC power 2-3 On Note: You cannot use COM 4 and DIO at the same time. Please adjust JP21 and JP22 together. Backlight Enable Power Select JP3 +3.3V (default) 1-2 On +5V 2-3 On Dimming Mode Select JP4 Voltage Mode 1-2 On PWM Mode (default) 2-3 On Digital I/O Output State JP18 (DIO 4-7) JP20 (DIO 0-3) GND (default) 1-2 On +5V or +5V_standby 2-3 On Digital I/O Power Select JP17 +5V_standby 1-2 On +5V (default) 2-3 On COM 4/DIO Select JP21, JP22 COM 4 (default) 1-2, 4-5 7-8, 10-11 On DIO 2-3, 5-6 8-9, 11-12 On LCD/Inverter Power Select JP2 +12V (default) 1-2 On +5V 2-3 On